Karbonn a111 rooting method.
Download the file from this link or attachment
https://www.dropbox.com/sh/j60bewdi6veje92/1RHtPTzXZ-/SRSRoot-Setup.exe
Extract in your windows pc or laptop(works in windows only)
step 1: install in computer.
step 2: install drivers for your phone.
step 3: Select USB DEBUGGING ON in your phone (it can be found in under developer options in settings).
step 4: connect your phone with computer via usb.
step 5: run the installed software.
step 6: select root.
wait till the process ends
your phone will reboot twice.
that's all
enjoy root now.........................
Related
Hey guys i am not expert but this guide is very easy for noobs
maybe it's helpfull for some people's
your device must in mass storage usb mode(see in setting somewhere)and usb debugging ON
1: download tft rom here http://forum.xda-developers.com/showthread.php?t=1598195
2: download flashtool here http://forum.xda-developers.com/showthread.php?t=1351324
3: install flashtool
4: install adb drivers,after flashtool installed you will find adb drivers in c:flshtool/drivers/flashtool drivers
5: copy tft file and paste to c:flashtool/firmwares
6: power off the device,pull out battery for few seconds then put it again
7: press volume down button and plug the usb cable(now device in flashmode)
8: open flashtool,click flash(icon flash),click OK on flashmode,select a firmware(ST18i) and ok.
when the rom installed, unplug the device and restart it,that's it,enjoy your ICS
Well my P7500 bricked this way http://forum.xda-developers.com/showthread.php?t=2180371
So I tried this procedure
http://forum.xda-developers.com/showthread.php?t=1130574
Section 2: Putting tablet in nvflash ADX mode
1: Turn tablet off
2: Unplug the tablet from pc
3: Hold vol up(right vol button) then hold power button at the same time
4: Keep holding them for 15 secs
5: The screen will stay black the whole time
6: After 15 sec let go of the buttons and plug the tab in to your pc
7: Open device manager and look for APX Device listed with an error
8: Right click on the APX device
9: Select 'Update driver software'
10: Select 'Browse my computer...'
11: Select 'Let me pick...'
12: Select 'Have disk'
13: Browse to c:\nvflash\usbpcdriver and make sure use sub folders is checked
14: Select NVIDIA USB Boot-recovery driver for mobile devices
15: Accept any warnings, including the big red alert (you may need to disable UAC)
16: Now in Device Manager under USB Controllers you should have an NVIDIA USB Boot-recovery driver for mobile devices
And of course as In my first post my computer is not able to find that hardware because it is showing me USB device not found. I tried on other computer but it didnt work also .
Sorry for my bad english
any suggestions will be helpful . please help me
enkhtwshn said:
any suggestions will be helpful . please help me
Click to expand...
Click to collapse
why double post?
you need to have the samsung usb drivers installed
download Samsung Kies and install it, it will also install the drivers
Hello Peeps,
Here is the tutorial on how to root Jelly Bean 4.3 Android on Grand 2 SM-N7102 Using CF-Auto-Root:
Prerequisites:
Install the USB driver with USB debugging enabled from the Developers Tool
Make a necessary backup of any important data.
Make sure your device has enough battery juice in it (80%)
Step 1: Download and extract the following files:
Download:
Zip File
Odin v3.09
You should get a .tar.md5 file within extracted folder. Extract Odin zip file and you will get Odin3 v3.09.exe along with few other files. You could use any extracting software such a WinZip, Winrar or 7zip to extract files.
Step 2: Put Your Phone In Download Mode
Now turn off your phone and wait few seconds for vibration to confirm complete switch off. Then boot it into the Download Mode. To do that press and keep holding the Volume down and Home button at the same time, with these two buttons pressed press the Power Button all simultaneously. When a warning message is displayed press on the Volume Up button to continue to the process.
Step 3: Run Odin
Now run Odinv3.09.exe in as an Administrator because an Admin privilege is required to complete this installation process without any hiccups. Now connect your phone with your PC using USB cable. Once you connect, you will see a message under Odin’s message box in the bottom left-panel displaying “Added”. You should also see ID: COM port with a number and colored box in Yellow/Blue i.e. if you successfully added your device, if not then you can do the following Steps:
Re-start the same procedure.
Try Uninstalling and then re-installing the drivers again and restart you pc.
Use different USB cable.
Ensure KIES is not running in the background.
Disable Your Antivirus.
Uninstall or disable any program that may be causing conflicts such as your OEM’s PC Suite or any other third party software.
Step 4: Staring the flashing process
In Odin, make sure Auto Reboot and F. Reset Time checkboxes are only two that are selected. DO NOT SELECT ANY OTHER OPTION! Click the AP button and select that file CF-Auto-Root-ms013g-ms013gxx-smg7102.tar.md5 you downloaded earlier in Step 1 with extension .tar.md5. Now, once you are ready, hit the START button to begin the flashing process. This process may take a minute or two to finish. Please do not disconnect your phone once Odin sets in motion. As the installation process completes, your phone will reboot itself and you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect it from the computer.
Voila, You have successfully rooted your phone
Closed. This is already here: http://forum.xda-developers.com/galaxy-grand-2/development/cf-root-root-galaxy-grand-2-t2698428
Phone bricked?? No problem. Here is the tutorial for Unbrick MediaTek (MT65xx) Phones.
You need VCOM driver, Stock Frimware and SP Flash tool to unbrick your phone.
SP Flash Tool Download HERE
Then Download Your MT65xx VCOM Driver, Please Google it
Then Download your Phone’s Stock Frimware, Please Google it
You also need..
1. a PC
2. a USB cable to connetc your phone with PC
3. a Brain
4. and A little respact
Note : No need battery unbrick your phone.
Instruction for install VCOM Driver to your PC :-
Download the zip and extract to desktop. Remove battery of your phone, open device manager in PC. Then connect your mobile with cable. Then you see adevice as adb or something like that in device manager. Right click on that and click update driver , then manually install the driver give path to that as u extracted in desktop tick on whole folder. That’s it. Your VCOM drivers are installed . Now your SP flash tool is ready to flash stock rom.
Instruction for flash stock rom with SP flash tool :-
1. Extract “Stock Frimware”
2. Open the folder “ SP_Flash_Tool”
3. Run “Flash_tool.exe”
4. Click “Scatter-loading”
5. Open “MT65xx_Android_scatter_emmc.txt” from your zipped firmware or google it if you don’t get it there.
6. Click Frimware -> Upgrade
7. After that remove your battery from your phone. Then connect your phone to PC via data cable
8. Wait for a while to finish the process.
9. When finished, Close Flash_tool Application.
10. Then carefully disconnect your phone from PC. Reinsert your battery. Then turn on phone. If all is ok, then your phone will be fine.
Thanks for reading.
NOTE !!! :good:
*Responsibility Will Not Be Taken By Me Incase Of Any Sort Of Damage.
*Rooting Does Not Work 100% All The Time So BE AWARE !!!
Step 1 : Download The Rooting Software To Your Computer.
Step 2 : Enable USB Debugging on your device.
Step 3 : Find the desktop icon of Android ROOT and double-click to launch it.
Step 4 : Connect your GALAXY S3 Mini to your computer via USB cable.
Step 5 : Click ROOT to start the process when you are ready.
Step 6 : ROOT Succeeded! Click Finish to reboot your device.
ENJOY YOUR ROOT !!!