Related
I now know the Allwinner A13 is a stripped down version of the Allwinner A10, to be clearer the specifications of my Tablet (from UniFlash and AnTuTu Benchmark) are as follows:
Manufacturer: None
Brand: softwinners
CPU hardware: sun5i
CPU model: ARMv7 Processor (VFPv3, NEON)
CPU frequency: 60.0 ~ 1008.0 MHz
Screen resolution: 800 x 444
GPU vendor: Mali-400 MP
GPU version (OpenGL): OpenGL ES 2.0
RAM size: 512 MB DDR2 RAM
Knowing this, I used UniFlash to make a backup of the firmware bt after using UniFlash to try and load a CM9 Rom on to the Tablet, the Tablet died. After alot of googling I discovered AllWinner based chipsets use Live Suite (sometimes called LiveSuit) to flash firmwares on to the device.
To Flash firmware on to the device you need to follow the attached instructions ((http://dragondevs.com/viewtopic.php?f=159&t=390):
Download LiveSuite (http://www.softpedia.com/get/System/System-Miscellaneous/Live-Suit-Pack.shtml)
Install Live Suite
Start Live Suite
Select the Live Suite image file (folder icon
Turn device off (to be sure hold power button for 12 - 20 seconds)
Hold "Volume Up" button down
Connect the device to your PC (while still holding "Volume Up" down)
Start pressing the power button (you may need to do this once a second for 5/6 seconds)
If you haven't installed windows will ask to install a driver for a device (Dive Id will be something like Vf73465789123465435_Id, if the device is in the right mode, A13-MID, ADB-Interface indicates the tablet has connected in anouther mode).
Once this has finished LiveSuite will detect the device and a wizard will flash the firmware for you.
I have found a working firmware which according to AnTuTU Benchmark gives my tablet a rating of 3047 (see firmware section), this is on the higher end of reported A13-MID tablets
I have found out how to install CWM on to the device via SaussageMod (http://www.slatedroid.com/topic/29916-scriptmod-for-allwinner-a1x-platforms/). This solution is untested, further more it may be unnessary futher investigation has shown this website (https://www.miniand.com/forums/forums/2/topics/73) has developed a way of create Live Suite images. This is simplier than installing clockworkmod recovery,
I tried to load the following images on to my tablet and failed completely: http://forum.xda-developers.com/showthread.php?p=31043317 It didn't work and forced me to do a firmware refresh.
My other step for the day was to create Ubuntu 10.10 installation then I began following this guide to construct an Xperia Play CM9 Rom/Kernel. once I have created a working ROM (I own an Xperia Play). I'm hoping to be able to modify the kernel to include the relevent A13 drivers, but one step at a time.
TODO
Create Ubuntu Partition
Follow Xperia Play CM9 Rom/Kernel Guide and create working rom (test on my Xperia Play)
Download CT repository (https://github.com/christiantroy) and compare with Xperia Play CM9 rom
Find the relevent drivers from https://github.com/amery/linux-allwinner leaked source
Retrieve offical MALI 400 MP drivers (parts of it have been released) compare with leaked source
Use UniFlash backup of original Rom along with LiveSuite image creation to try and restore original firmware (see If I understand it properly)
Examine Build.prop find out why original firmware displayed ina phone layout and new one is in tablet mode (potentially reference CM supported Tablets).
Attempt to compile a A13 (Sun5i) based rom
Create a google code page to hold all of these thoughts properly.
Left blank will include rom/firmwares here for future reference
Firmware
https://www.dropbox.com/sh/bzjt7mzuftwz79f/nt7mRMPDj1 - My public Dropbox
http://www.azhuo.net/en/products_A13B_Allwinner-A13_7_inch_Android_4.0_Upgrade.html - password is: tabletpc
http://dragondevs.com/viewtopic.php?f=159&t=390 - McPad F1 firmware
Novo 7 Tools
https://dl.dropbox.com/u/74970692/Novotools_v1.0.apk
SausageMod
http://www.slatedroid.com/topic/29916-scriptmod-for-allwinner-a1x-platforms
Gapps - http://goo.im/gapps/
I have the same tablet and it would be very cool if you succeeded in your attempt to create a CM9 rom for it. I tried ROM made by Tragidy from this thread but there is a problem with touchscreen driver, ROM booted successfully but I could not even unlock the screen cause touchscreen did not work. I finaly flashed rom DCPAD2121.zip using livesuite which I belive is the original ROM that came with tablet and it worked.
I installed clockwordmod using sausagemod successfully, but there is a big problem - no hardware "back" key and only volume up works.
novo7tools.apk works OK for reboot, reboot to recovery or shutdown.
syncing
Thanks, it's slow going at the moment, I only spending ~1 hour each day on it and at the moment trying to sync the CM9 source is painful (it keeps timing out, due to "remote side corruption").
I figure I would start there as all the firmware images I can find are ICS roms (meaning the drivers must be ICS).
Hi, I have the same tablet but I cannot find the firwmare DCPAD2121.zip
Could you upload it please? From dropbox has been deleted
Thanks
You should check this topic:
http://forum.xda-developers.com/showthread.php?t=1861445
WillingMagic said:
You should check this topic:
http://forum.xda-developers.com/showthread.php?t=1861445
Click to expand...
Click to collapse
I tried that ROM, on my tablet after flashing the ROM it got stuck in a boot loop. It might be an idea to steal the config he created. The ROM is pre CM9 release. The A10 Flash kitchen software seems to work. I was hoping on producing a complete Live Suit image that people could flash (figuring our what CT has done on the A10 took a while).
Still having fun trying to sync the repositories, given up on trying to use a Debian VM, I'll will install full Ubuntu on a drive tomorrow, hopefully that will help fix things. It doesn't help most of the guides I can find are out of date and I keep having to make corrections.
I've also uploading all firmware I can find to my dropbox (at 200mb each they will take a while), I won't with tools simply because others ask you not too.
The Dropbox firmware was out of date when I tried to download it sun5i_android_a13-pfdq88_en_D06 firmware worked well for me, the firmwares are located at: https://www.dropbox.com/sh/bzjt7mzuftwz79f/nt7mRMPDj1
Cyanogenmod 9 in not working for you. Did you made data and cache wipe? Can you send me logcat and dmesg output?
You can`t steal my config, you have to remember about credits, and other stuff.
Creating a wiki is useless, there is already wiki for allwinner products, so better update info on it.
Github is better than google code to keep sources.
Using Livesuit=Windows, I hate dual booting just for flashing, Clockwork Recovery or modified SDcard with uboot is better solution.
Current kernel is not working well, with sun5i.
Using VM is stupid, because building rom takes a lot of time on quad core pc without it.
WillingMagic said:
Cyanogenmod 9 in not working for you. Did you made data and cache wipe? Can you send me logcat and dmesg output?
You can`t steal my config, you have to remember about credits, and other stuff.
Creating a wiki is useless, there is already wiki for allwinner products, so better update info on it.
Github is better than google code to keep sources.
Using Livesuit=Windows, I hate dual booting just for flashing, Clockwork Recovery or modified SDcard with uboot is better solution.
Current kernel is not working well, with sun5i.
Using VM is stupid, because building rom takes a lot of time on quad core pc without it.
Click to expand...
Click to collapse
I wiped the caches I couldn't send a logcat or dmesg as the device simply boot looped.
I've been providing links to threads whenever I come across others work, I'm new to android rom development for me this is a research effort which will hopefully produce something cool for my £50 tablet. Basically my day job has switched to developing UI's and I am looking for something new to learn (instead of why is Vaadin, Guice, SWT, Javascript, etc... is putting that button there).
Said dev career has also made me hate Git with a passion (not as bad as perforce but still) since Git integrates poorly with Visual Studio and Eclipse and you end up getting everyone overwriting each others changes. The idea of google code is simply because it makes a good platform for projects and you can use things like git with it. I didn't know about an Allwinner wiki, with all of my Googling I haven't come across it, where is it?
I don't care about build times I'm just researching, alas Debian has caused me enough problems so I've installed ubuntu on to a old disk I had lying around. Considering I've just tried to install Ubuntu via a Net install CD and it has screwed up the GRUB installation (nicely taking out my windows partition as well) can you blame me?
The reason for nabbing the config (and the Xperia Play and Christian Troys) is to understand how they work. Over the years I've found most Open Source software documentation is poor unless you have a set level of knowledge about it already.
Lastly I like automation, I want things to just work. Livesuit does that since I am normally a windows user, I as hoping in the distant future once I understand the build process to set up a Jenkins server to do it and create the whole lot automatically (via the Allwinner flash kitchen). In the even longer term I would like to update FlashTool to do what LiveSuit does. In the near term (next couple of months) I just want to be able to build a CM9 image.
All android and kernel source are keep on git, so changing it is stupid.
This is allwinner wiki: http://rhombus-tech.net/allwinner_a10 you can also update http://elinux.org/Hack_A10_devices
Everyone use CWM and it's standard for unofficial firmware/ROMS
brandonlee2 said:
Hi, I have the same tablet but I cannot find the firwmare DCPAD2121.zip
Could you upload it please? From dropbox has been deleted
Thanks
Click to expand...
Click to collapse
Here's my upload, I packed it in rar format: http://www.mediafire.com/?we4zhgop29bg3dj
I also found it here: https://docs.google.com/open?id=0BzQuMwoMQqvba1VtQ1p1ZWJkR2M
from this forum post: http://www.slatedroid.com/topic/35314-a13-generic-tablet/page__view__findpost__p__421128
I built a CM10 rom for A13 from sources. It boots fine but hangs either at the Android setup wizard or sometimes even at the CM animation.
myfluxi said:
I built a CM10 rom for A13 from sources. It boots fine but hangs either at the Android setup wizard or sometimes even at the CM animation.
Click to expand...
Click to collapse
Mind sharing your repo ?
Trying 4.1.2
Hi all,
So I've tried compiling from 4.1.2 source for my A13 Emgeton Consul 3
It boots up and gets to the CM10 boot animation but it doesn't get past it.
I can adb at first boot until adb stops.
logcat from boot attempt:
http://pastebin.com/gLTrieHm
My build.prop:
http://pastebin.com/Ap9M1tjW
Any pointers as to why it doesn't get past the boot animation?
Hello guys! I know it's not he proper place here to pose my question, but I am definitely at loss!
Do you happen to know if there is a way of rooting this tablet? And if so, does everything work properly after that?
phoivos86 said:
Hello guys! I know it's not he proper place here to pose my question, but I am definitely at loss!
Do you happen to know if there is a way of rooting this tablet? And if so, does everything work properly after that?
Click to expand...
Click to collapse
Mine came pre-rooted.
Just received my MID A13 Tablet. Is this thread dead?
koodiifin said:
Just received my MID A13 Tablet. Is this thread dead?
Click to expand...
Click to collapse
I've gone a bit quiet on the development front, setting up a file/media server & samba domain server to power my home network is eating up my time.
My dropbox contains every image I could find for the tablet, as mentioned previously you can root the device using saussage mod, although my device and every one of those images is already rooted. You can prove this by installing super user.
Sassage mod's clockworkmod recovery doesn't work for me and I was looking at the backup tool in order to generate my own one. If you are aimed at any development, let me know and I will update the main thread
Many have said that they have "lost" "forget" to take backup from original rom. So, i'd like to have backup from my original to go back if/when something goes wrong. How do i do that? What software i need. Do i need to root?
This is from my info sheet:
Model TWD_MID
android version 6.0.1 ?????
Baseband 1.5
Kernel 3.0.8+
Buildnumber: nuclear_evb-eng6.0.1 IMM76D 20120917 test keys
I am in a desperate need for some help:
My tablets specs are these:
Phone model: A13-MID
Brand: softwinners
CPU hardware: sun5i
CPU model: ARMv7 Processor (VFPv3.NEON)
CPU frequency: 60.0 - 1008.0 MHz
Screen Resolution: 800 x 444
GPU vendor: ARM
GPU render: Mali-400 MP
GPU version (OpenGL): OpenGL ES 2.0
Memory size: 353.5 MB
Android version: 4.0.4
Build number: nuclear_pfdq88c-eng 4.0.4 IMM76D 20120821 test-keys
Kernel: Linux version 3.0.8+
I just installed OpenVPN installer and installed the OpenVPN binary in the system/xbin
After that I tried to connect to my university's VPN but when it tried to connect, the tablet lost wifi connection and ever since it doesnt connect to any available wifi network!! I manually deleted the OpenVPN binary, but problem remains!
Do you know where could I find the stock ROM for this tablet in order to re-flash it?
Do you have any other proposals? Anything will help!
Thank you very much!!
i just bought a chinese htm xs5292 runnin 4.1.1 i want to root and upgrade to 4.3 any help on how to do this would be greatly appreciated, here are the specs
manufacturer - htm
model - x5292
android version - 4.1.1
kernel - x5292 dual core
software - mt5617-c913-en-vo5
hardware - c913-v1.02
i'm a first timer at this so please speak like you would to a child (even though i'm 35)
many thanks in advance
paul
paul0909 said:
i just bought a chinese htm xs5292 runnin 4.1.1 i want to root and upgrade to 4.3 any help on how to do this would be greatly appreciated, here are the specs
manufacturer - htm
model - x5292
android version - 4.1.1
kernel - x5292 dual core
software - mt5617-c913-en-vo5
hardware - c913-v1.02
i'm a first timer at this so please speak like you would to a child (even though i'm 35)
many thanks in advance
paul
Click to expand...
Click to collapse
I can help you get rooted. First you will need to install drivers on your PC so your device can communicate with the root program. Then try this:
http://forum.xda-developers.com/showpost.php?p=43163569&postcount=7
If that dont work, let me know. You can always use MTK Droid Tools and SP flash tool to pull your stock recovery and port it into a custom recovery that will allow you to flash a simple root.zip
Hope this helps!
usb drivers
thanks Klown80, that looks like it should work, but first i need to install my usb drivers, i have loked at a ton of sites and they all didnt work, i need spreadtrum usb drivers, but can't figure out wich ones, a few said they all worked on any spreadtrum phone, but either im installing them incorrectly, or they simply didnt work,
again, thanks for any help in advance
paul
paul0909 said:
thanks Klown80, that looks like it should work, but first i need to install my usb drivers, i have loked at a ton of sites and they all didnt work, i need spreadtrum usb drivers, but can't figure out wich ones, a few said they all worked on any spreadtrum phone, but either im installing them incorrectly, or they simply didnt work,
again, thanks for any help in advance
paul
Click to expand...
Click to collapse
Try using this, it installs drivers for many different phones, it may not be the actual manufacturers drivers for your specific device but it will help get your phone talking to your PC:
http://www.snappea.com/
Also - Make sure you are going into settings and turning USB debugging on. You can usually find this under Settings > Developer Options.
snapea
Again, thanks Klown, but no joy, i tried serveral times and after 15 - 20 mins of "fobulating" (is that even a real word ) my phone it said "failed to processs phones data" i tried restarting both devices etc and a couple of other thing suggested but no joy.
Any other ideas, as always thanks in advance.
Paul
oh ps, i also tried to connect to snapea via wifi, but got the same message
paul0909 said:
Again, thanks Klown, but no joy, i tried serveral times and after 15 - 20 mins of "fobulating" (is that even a real word ) my phone it said "failed to processs phones data" i tried restarting both devices etc and a couple of other thing suggested but no joy.
Any other ideas, as always thanks in advance.
Paul
oh ps, i also tried to connect to snapea via wifi, but got the same message
Click to expand...
Click to collapse
Try these drivers
https://www.dropbox.com/sh/oaslz8xuxk7ag50/VRzHnZvA-b
finally
\it worked, can't thank you enough, one more bothersome question, now i have my phone rooted how do i safely, and i emphasise safely upgrade from 4.1.1 to 4.3
I have looked into it a bit myself, and am in half a mind to give it a go, but the warnings about bricking my phone always puts me off, so once again, thanks in advance for any help given, and many thanks for the help so far.
Paul
paul0909 said:
\it worked, can't thank you enough, one more bothersome question, now i have my phone rooted how do i safely, and i emphasise safely upgrade from 4.1.1 to 4.3
I have looked into it a bit myself, and am in half a mind to give it a go, but the warnings about bricking my phone always puts me off, so once again, thanks in advance for any help given, and many thanks for the help so far.
Paul
Click to expand...
Click to collapse
Go here and download MTK Droid Tools from first post:
http://forum.xda-developers.com/showthread.php?t=2160490&styleid=18
Run the program and connect your phone to PC, this tool will tell you lots of info about your phone but the main function is to possibly back up your stock firmware (This is good to have if you plan on trying to flash anything to the phone, this way you will have your stock files to fall back on in case something you flash to the phone does not work.) Once you have MTK Droid Tools running and phone connected, what does it say next to Hardware on the phone info tab please?
I am not sure off top of my head about updating to a higher version of Android but this back up step is REALLY important. It is hard if not impossible to find stock firmware floating around on the net for these chinese clone devices. IF you have stock files backed up you can flash almost anything you want knowing you have a way to restore your phone to working order. IF you look around here on XDA you will see tons of posts by people looking for the stock firmware for their clone phone after soft bricking it playing around. Sadly there is not much help for them unless they find someone with the EXACT same phone and are willing to share their back up (if the next person made one theirselves that is!)
hardware
Klown80 said:
Go here and download MTK Droid Tools from first post:
http://forum.xda-developers.com/showthread.php?t=2160490&styleid=18
Run the program and connect your phone to PC, this tool will tell you lots of info about your phone but the main function is to possibly back up your stock firmware (This is good to have if you plan on trying to flash anything to the phone, this way you will have your stock files to fall back on in case something you flash to the phone does not work.) Once you have MTK Droid Tools running and phone connected, what does it say next to Hardware on the phone info tab please?
I am not sure off top of my head about updating to a higher version of Android but this back up step is REALLY important. It is hard if not impossible to find stock firmware floating around on the net for these chinese clone devices. IF you have stock files backed up you can flash almost anything you want knowing you have a way to restore your phone to working order. IF you look around here on XDA you will see tons of posts by people looking for the stock firmware for their clone phone after soft bricking it playing around. Sadly there is not much help for them unless they find someone with the EXACT same phone and are willing to share their back up (if the next person made one theirselves that is!)
Click to expand...
Click to collapse
Thanks again, while i go to the link and follow the next steps i thought i'd put up the hardware version you asked for
hardware - c913-v1.02
Paul
edit
even though my pc now recognises the fact that tere is a spreadtrum phone in my devices list and i managed to root it ok, when i load up mtk droid tools it says "the device isn't revealed, connect or reconnect a cable"
needless to say i tried reconnecting and it didn't change i downloaded the adb drivers from the link under the mtk link but have no idea what to do with them,
appologies for my ignorance in all of this, but like i said in my first post, i have no idea what i'm doing with all this, thanks
paul
pps the hardware version i posted was from the info on my phone
Don't know if I should've asked somewhere else but here it goes...
The device I have is a K-Free (or K-Phone) K480 aka Karbonn Titanium S25 Klick (it has another name in the store I bought it jeez) and what I'm specifically trying to do is to boot a kernel from another phone, almost exactly the same model Gigabyte GSmart Mika M3. Both phones run on the MT6582 platform.
Both devices are nearly identical, with the exception of the front facing camera where on the GSmart it is 8MP and on mine it is 5MP (the only difference in H/W mind you) and I even have the case for it on my phone. The point is - the hardware could be considered the same thing. Then I took a look at the software side of things...
Guess what - everything's almost the same as well, down to the partition layout (scatter files identical), littlekernel (uboot) works on my phone and yet I can't boot the boot.img of it or even the OS (haven't tried too hard on copying system.img, it should've worked with the ROM I have) so the only conclusion I can make is that the preloader needs to be flashed as well which is the most scary part.
Comparing the two preloaders from each phone, the one I have is newer than the one from the GSmart and I know why exactly - the dude in the store flashed my phone since it was a "new" model lol. The OEM provided them with software for Karbonn Titanium S25 (v1.7). Other than the date, there are still some differences - at the large chunk at the beginning it is the same, some stuff is moved around and most of all the final portion is different and I assume that's for the kernel side of things, but I could be wrong. So in conclusion, a large part of it is similar as well.
The reason why I make this fuss about is because Gigabyte seems to update their devices more often for one and the second reason would be simply exploring the possibilities of what I can and can't do with my phone and finally, the third reason would be ultimately, Gigabyte provided me with kernel sources for their Mika M3 and yet nobody from K-Free or Karbonn have responded so I have to get the stock GSmart kernel running on my device anyway and I know it's possible.
I need to know one thing for sure - would this work? The only way to find out is to flash it and I am a bit skeptical to try it out. Unless there's a safe escape route (no testpoints or anything, it's under warranty), I really don't know if I'm going to try it at all. At least, if anybody knows if the device will load some preloader or USB VCOM mode if it fails, please let me know.
EDIT: Just to let you know, holding Vol Down while plugged in without battery loads the meta mode, so it may work after all. I ask people who are familiar with MTK devices to confirm if MT6582 after failed preloader will continue doing that.
EDIT2: I was a bit impatient, but hey, flashing the preloader worked! lol Now onto turning the phone into a Mika M3 completely...
EDIT3: OK nevermind it seems I have answered my questions myself. To everyone who owns this device: you can flash Mika M3 software on it. Everything works just fine.
I found this bricked tablet, it's a generic chinese 7 inch tablet, it has the MTK8382 processor, single SIM, but I can't figure out anything else about it. Is there any kind of universal rom for these things? I tried to install some roms I found online for models with a similar shape but I ended up bricking it, now it just display lines on the display or a white screen when I turn it on, nothing else works. Should I just throw it away?
It's this generic model that can be found on alibaba if you want to buy in bulk and start your awful tablet company: http://www.alibaba.com/product-detail/MTK8382-7-inch-alps-tablet-pc_60273334448.html
I managed to resuscitate it using a rom meant for a device called IKON 7 Tablet, also known as Royqueen MR706. I had flashed at least 20 roms for similar devices before I found this one. It works 100%, even the camera and the FM radio, so it must mean it's a clone of a clone of a clone with the same source hardware from the same crappy chinese factory. This rom is pretty decent too, moderately fast and only has a few crappy games preinstalled, no malware or weird stuff. It even comes with the google apps (still not giving it my google account), flash player, and office suite.
This is the info from MTK Droid Tools. Any other rom I can get for this device to make it a bit more useful?
Also, it seems like I lost the original IMEI of this device. Is there any way to recover it or give it a working IMEI?
I have the same tablet too!
MarkMRL said:
I managed to resuscitate it using a rom meant for a device called IKON 7 Tablet, also known as Royqueen MR706. I had flashed at least 20 roms for similar devices before I found this one. It works 100%, even the camera and the FM radio, so it must mean it's a clone of a clone of a clone with the same source hardware from the same crappy chinese factory. This rom is pretty decent too, moderately fast and only has a few crappy games preinstalled, no malware or weird stuff. It even comes with the google apps (still not giving it my google account), flash player, and office suite.
This is the info from MTK Droid Tools. Any other rom I can get for this device to make it a bit more useful?
Also, it seems like I lost the original IMEI of this device. Is there any way to recover it or give it a working IMEI?
Click to expand...
Click to collapse
Hi! I have the same tablet and in my case this ROM not worked.
My tablet is: Mediatek MT8312v. Was bricked, and I tried flash with ROM royqueen MR706D by rp_yonex (maybe you saw it out there) but not revived correctly... showed a IKON logo when it start but the display and touch function failed, the screen is misaligned or is seen as half, i don´t know how say, just not functioned correctly.
But i think that i'm not very away from solution.
Even though the screen does not work very well, I could get this data in the "settings/ about tablet" :
Model number: IK-TPC783
Android version: 4.2.2
Baseband version: MOLY.WR8.W1315.MD.WG.MP.V18, 2013/11/29 20:10
Buil number: MT83x2_MR706_MR7063L1C2W1.2014031418
Custom build version: 1.19_20140125
Hardware info: MT8312
Please help!
I'm having an issue with a VERY similar device... It's an MR706, with zero markings indicating brand/manufacturer... The motherboard appears to be model K20-MB-V1.0 and there's a chip (not sure WHICH chip) with a brand called FORESEE on it. Anyway - I attempted to update the firmware using that royqueen scatter, and now the thing won't boot at all. Held the reset button, held all buttons, plugged in (it was at 96% battery before I flashed it) - nothing. Wondering if it's totally bricked or if there's some magic that someone can teach me...
Ithilhin said:
I'm having an issue with a VERY similar device... It's an MR706, with zero markings indicating brand/manufacturer... The motherboard appears to be model K20-MB-V1.0 and there's a chip (not sure WHICH chip) with a brand called FORESEE on it. Anyway - I attempted to update the firmware using that royqueen scatter, and now the thing won't boot at all. Held the reset button, held all buttons, plugged in (it was at 96% battery before I flashed it) - nothing. Wondering if it's totally bricked or if there's some magic that someone can teach me...
Click to expand...
Click to collapse
You must be sure the exact model to the chip (the big one usually). In my case it's "MediaTek ARM MT8312v". You can search a compatible ROM to flash with the SP Flash Tools.
Or check if this help (mytabletguru.com/how-to-find-chinese-tablet-firmware)
Share the results!
qsdinf said:
You must be sure the exact model to the chip (the big one usually). In my case it's "MediaTek ARM MT8312v". You can search a compatible ROM to flash with the SP Flash Tools.
Or check if this help (mytabletguru.com/how-to-find-chinese-tablet-firmware)
Share the results!
Click to expand...
Click to collapse
While I'm a fairly seasoned technician, I'll fully/freely admit to this being the first Android tablet I've taken apart. Here's a picture of the innards - help? The only chip with writing/markings is on the top-left - and there's nothing with MediaTek, ARM, or MT - though there is a number that's been popping up in my searches (8382)...
I have same problem
hello how are you dear,
i have a tablet ismart china tablet. Model is i-tab79g8.
i flash this tab whith sp flash tool. i cannot make a backup old files.
i download a scatter file.
this scatter was install success. but when power on the device screen lights on but no display on lcd.
i am so worry please help me.
some additional information hear.
SP. Flash tool information.
Chip Name: MT6582_s01
Chip version: 0x0000ca01
Ext clock: EXT_26M
RAM Type: DRAM
so when i open back cover i see
bord number : K733 B1-1 20140329
processor: MEDIATEK ARM MT8312 V 1421-XAHHTH CTT3P551
PLEASE HELP ME
I just noticed these new posts in my thread. Unfortunately I'm not able to help any of you because I literally fixed mine via trial and error. Like I said I kept flashing rom after rom until one worked. I bricked it in several ways before getting the right rom, it had all kinds of issues from not booting at all, showing a boot logo and then bootlooping, showing lines on the screen, and so on. I found it by googling for devices with similar hardware.
But honestly, it wasn't worth it to fix this p.o.s.
If you have a similar device you're better off getting rid of it and buying a new one.
Hello everyone.
Before explaining my problem, I must apologize for my english (I'm from Argentina).
I have to say I'm confuse.
My grandfather gave me a phone he didn't use (because mine died), an Archos 45c Titanium with lots of viruses (old people way of use I guess), so I tried to root with Kingo in order to clean it, but it got bootloop and it's not going further of the logo screen and stay vibrating forever. So I googled for instructions to flash it and found the stock rom (archos 45c titanium MT6572) and SP Flash Tools, MTK drivers and even ADB drivers. But couldn't manage to get my phone detected by SP Flash Tools so I started a quest searching for the right driver (and a lots of ways to clean my driver library in Win 10), but none of the older or newest versions of MTK/ADB/CDC/VROM drivers managed to detect my phone, not even by adding legacy hardware. Until I found Spreadtrum drivers that I installed with no much hope, but they worked perfectly. So I googled if there's any version of archos 45c with Spreadtrum processor (most of them say MT6572), and I found just a couple of web with specification for an Archos 45c Titanium with SC7731 Spreadtrum processor.
My question is... Is this even possible? xD Maybe I just mess up everything good in the world and now I'm hallucinating... or is it my phone really that rare? And more important, anybody knows where I can find a .pac stock rom for a device wich is suposse to be MT6572? If not, can I use another stock rom for another archos 45 Spreadtrum series?
Thank you in advanced.