My phone is fine until I'm on travelling severl days ago, I recharge the phone with power bank that I usual use when I cand find any electricity port.
For several minute my phone become warm, and more warmer and close to hot. I try to switch off my phone, then remove battery (its more warm or hot than I expect) after its become colder I try to install battery and swich on power, tara.... There is nothink happen.. Try to charge with charger no response on its screen, still blank. Try to connect on my laptops, its same nothink happens. No hardware detection or etc...
First I think the battery is dead, I try to charge the battery directly with universal charger until the battery full charge, but the result is same my phone still on its "freeze".
Than I try to use fastboot but on 2nd stage give response like i mention below, its FAILED to writing X and U (remote : partition does not exist)
anyone has solution for this?
Code:
waiting for 2ndstage response...
usb_read 4
usb read = aabbccdd
accepted 2ndstage response
sending image to target...
size = 246272
usb_write 4
usb_write 246272
** Done **
< waiting for device >
sending 'x-loader' (384 KB)...
OKAY [ 0.201s]
writing 'x-loader'...
FAILED (remote: partition does not exist)
finished. total time: 0.217s
sending 'u-boot' (1024 KB)...
OKAY [ 0.527s]
writing 'u-boot'...
FAILED (remote: partition does not exist)
finished. total time: 0.534s
Done
Press any key to continue . . .
adim6001 said:
My phone is fine until I'm on travelling severl days ago, I recharge the phone with power bank that I usual use when I cand find any electricity port.
For several minute my phone become warm, and more warmer and close to hot. I try to switch off my phone, then remove battery (its more warm or hot than I expect) after its become colder I try to install battery and swich on power, tara.... There is nothink happen.. Try to charge with charger no response on its screen, still blank. Try to connect on my laptops, its same nothink happens. No hardware detection or etc...
First I think the battery is dead, I try to charge the battery directly with universal charger until the battery full charge, but the result is same my phone still on its "freeze".
Than I try to use fastboot but on 2nd stage give response like i mention below, its FAILED to writing X and U (remote : partition does not exist)
anyone has solution for this?
Code:
waiting for 2ndstage response...
usb_read 4
usb read = aabbccdd
accepted 2ndstage response
sending image to target...
size = 246272
usb_write 4
usb_write 246272
** Done **
< waiting for device >
sending 'x-loader' (384 KB)...
OKAY [ 0.201s]
writing 'x-loader'...
FAILED (remote: partition does not exist)
finished. total time: 0.217s
sending 'u-boot' (1024 KB)...
OKAY [ 0.527s]
writing 'u-boot'...
FAILED (remote: partition does not exist)
finished. total time: 0.534s
Done
Press any key to continue . . .
Click to expand...
Click to collapse
You my friend (I think) have a hardware issue and no one on this site can really help you with that. Contact LG
Related
I used the files from dell opensource and did the bootloader unlock and flashed a rooted boot image and now my tablet wont load to the os. it juszt goes to a black screen that say [email protected]:/ in upper left hand corner? I dont know what to do now. help!
It appears that you are trying to root the device. Please review [GUIDE] How to root Android 4.4.4 on the Dell Venue 3840
(Merrifield) Tablet
You may post there if you need additional information.
I did
Perseus said:
It appears that you are trying to root the device. Please review [GUIDE] How to root Android 4.4.4 on the Dell Venue 3840
(Merrifield) Tablet
You may post there if you need additional information.
Click to expand...
Click to collapse
I did go there and used those instructions. and the file that was provided. thats when it all happened. I have since flashed the boot.img from opensource back onto it and it works again. and used kingo root program. so it is showing rooted. but now I see that I am no longer running kitkat 4.4.4 but kitkat 4.4.2. I want to upgrade back but I am having the hardest time finding roms for my tablet. and I notice that so much of the main stuff like google play services take way too much ram, leaving me with barely 200 mb ram left to work with. and its a 1 gb. hmmm and I wanted to change my recovery to clockworkmod but it says my device isnt supported yet. I really am coming against roadblocks to optimizing the tablet. I cant even run my fb games cuz they wont sign into fb. they just keep restarting. grrrr any thoughts or ideas? thanks. also I could never get xfstk to work.
xFSTK downloader
I am trying to follow the tutorial but the xFSTK downloader is not working. It says "Details: No provisioning activities in progress..."
Anyone know what could be causing this issue?
Thanks in advance,
tomasro27 said:
I am trying to follow the tutorial but the xFSTK downloader is not working. It says "Details: No provisioning activities in progress..."
Anyone know what could be causing this issue?
Thanks in advance,
Click to expand...
Click to collapse
Post a screenshot of your computer showing this message.
turn off device
plug in
hit begin button
press volume up and power
takes like 3-5 seconds and goes as told to?
Perseus said:
I will request to have this thread moved to appropriate forum so other experts for that device may be of help.
Click to expand...
Click to collapse
Hi Perseus,
I am wondering if you know where this thread has been moved thus I could check for more updates. I have the same issue after following this - http://forum.xda-developers.com/dell-venue/development/guide-how-to-root-android-4-4-4-dell-t2918427
Presently my tablet goes black and I can see only "[email protected]:/" on top left.
Thanks!
3480
You can always flash back the original rom 4.4.4
https://www.androidfilehost.com/?fid=95784891001602440
did you manage to get your tab rooted with kingo on 4.4.2.
hamzilla said:
Hi Perseus,
I am wondering if you know where this thread has been moved thus I could check for more updates. I have the same issue after following this - http://forum.xda-developers.com/dell-venue/development/guide-how-to-root-android-4-4-4-dell-t2918427
Presently my tablet goes black and I can see only "[email protected]:/" on top left.
Thanks!
Click to expand...
Click to collapse
---------- Post added at 11:39 AM ---------- Previous post was at 11:11 AM ----------
You have to select those 4 files downloaded from here (opensource.dell.com/releases/Venue_8_3840_Merrifield/developer-edition/A195/OTA/)
FW DnX= dnx_fwr_*.bin
IFWI= ifwi_*.bin
OS DnX= dnx_osr_*.bin
OS Image= droidboot.img.POS.bin
then put your tablet into fast boot mode
1. Enable fastboot mode
1) Open “xFSTK Downloader 1.5.1”.
2) Select the second “MRD AO/BO + MOOR AO + CRC” tab as the following................................
tomasro27 said:
I am trying to follow the tutorial but the xFSTK downloader is not working. It says "Details: No provisioning activities in progress..."
Anyone know what could be causing this issue?
Thanks in advance,
Click to expand...
Click to collapse
HELP
after writing system in fastboot mode this gets me error
C:\Users\home\Desktop\Venue 8 1.22>fastboot oem start_partitioning
...
(bootloader) Start partitioning
OKAY [ 1.016s]
finished. total time: 1.016s
C:\Users\home\Desktop\Venue 8 1.22>fastboot flash /tmp/partition.tbl partition.t
bl
sending '/tmp/partition.tbl' (1 KB)
fname=partition.tbl...
1 KB / 1 KB
OKAY [ 0.766s]
writing '/tmp/partition.tbl'...
OKAY [ 1.031s]
finished. total time: 1.797s
C:\Users\home\Desktop\Venue 8 1.22>fastboot oem partition /tmp/partition.tbl
...
OKAY [ 1.156s]
finished. total time: 1.156s
C:\Users\home\Desktop\Venue 8 1.22>fastboot erase system
erasing 'system'...
OKAY [ 55.253s]
finished. total time: 55.253s
C:\Users\home\Desktop\Venue 8 1.22>fastboot erase cache
erasing 'cache'...
OKAY [ 9.079s]
finished. total time: 9.079s
C:\Users\home\Desktop\Venue 8 1.22>fastboot erase data
erasing 'data'...
OKAY [ 26.158s]
finished. total time: 26.158s
C:\Users\home\Desktop\Venue 8 1.22>fastboot erase logs
erasing 'logs'...
OKAY [ 11.329s]
finished. total time: 11.344s
C:\Users\home\Desktop\Venue 8 1.22>fastboot oem stop_partitioning
...
(bootloader) Stop partitioning
OKAY [ 0.984s]
finished. total time: 0.984s
C:\Users\home\Desktop\Venue 8 1.22>fastboot flash boot boot.img
sending 'boot' (8342 KB)
fname=boot.img...
8342 KB / 8342 KB
OKAY [ 1.235s]
writing 'boot'...
OKAY [ 1.422s]
finished. total time: 2.657s
C:\Users\home\Desktop\Venue 8 1.22>fastboot flash fastboot droidboot.img
sending 'fastboot' (11114 KB)
fname=droidboot.img...
11114 KB / 11114 KB
OKAY [ 1.375s]
writing 'fastboot'...
OKAY [ 1.594s]
finished. total time: 2.985s
C:\Users\home\Desktop\Venue 8 1.22>fastboot flash recovery recovery.img
sending 'recovery' (10202 KB)
fname=recovery.img...
10202 KB / 10202 KB
OKAY [ 1.313s]
writing 'recovery'...
OKAY [ 1.531s]
finished. total time: 2.860s
C:\Users\home\Desktop\Venue 8 1.22>fastboot flash system system.img
sending 'system' (728453 KB)
fname=system.img...
102400 KB / 728453 KB
204800 KB / 728453 KB
307200 KB / 728453 KB
409600 KB / 728453 KB
512000 KB / 728453 KB
614400 KB / 728453 KB
716800 KB / 728453 KB
728453 KB / 728453 KB
OKAY [ 50.565s]
writing 'system'...
OKAY [ 45.752s]
finished. total time: 96.317s
C:\Users\home\Desktop\Venue 8 1.22>fastboot flash splashscreen_7 oemlogo_7.bin
error: cannot get size of 'oemlogo_7.bin'
C:\Users\home\Desktop\Venue 8 1.22>fastboot flash splashscreen_8 oemlogo_8.bin
error: cannot get size of 'oemlogo_8.bin'
C:\Users\home\Desktop\Venue 8 1.22>fastboot flash dnx dnx_fwr_0003_20CA_YT2_TB2_
signed.bin
error: cannot get size of 'dnx_fwr_0003_20CA_YT2_TB2_signed.bin'
C:\Users\home\Desktop\Venue 8 1.22>fastboot flash dnx dnx_osr_0003_20CA_YT2_TB2_
signed.bin
error: cannot get size of 'dnx_osr_0003_20CA_YT2_TB2_signed.bin'
C:\Users\home\Desktop\Venue 8 1.22>fastboot flash ifwi for_product_ifwi_0003_20C
A_YT2_TB2_signed.bin
error: cannot get size of 'for_product_ifwi_0003_20CA_YT2_TB2_signed.bin'
C:\Users\home\Desktop\Venue 8 1.22>pause
Press any key to continue . . .
Click to expand...
Click to collapse
Renz Kell said:
HELP
after writing system in fastboot mode this gets me error
Click to expand...
Click to collapse
It's been a while since I had those tablets I had three of them I remember having a similar problem I tried lots of times to reflash so I started over I redownload the tablets images again and the Odin and I dont know which one was at fault but that did the trick also made sure I was using 7zip on my PC rar or zip won't work 7zip I seem to recall having a big issue there as the images I downloaded were zipped up and I had to convert to 7zips to work anyways I hope that helps a little good luck
Sorry my poor english, guys.
No response from the phone. No vol - home power, nor any other combination. No logo, no charging led, no vib... Black screen.
When plugged without battery, the PC detects the Omap4, so I can enter flasboot, but every writting attemp results in a "FAILED (remote: partition does not exist)". Here's an example:
sending 'x-loader' (384 KB)...
OKAY [ 0.203s]
writing 'x-loader'...
FAILED (remote: partition does not exist)
Any advise about this? Is it really dead?
Thanks.
Hey guys am new to this forum even though I have been using your advice for some years now This time I finally encounter my self in really really big trouble with my brand new dell venue 7840 , what happens is that i got the freaking updated for lollipop out of the box, next to that i followed all steps to root lollipop it took some time but everything went 'right'. But 3 days later my tab started to drastically drain Battery, to the point were i cant actually see it going from 100% to 0% in just a minute or two, i hope making some kind of a downgrade to 4.4.4 could fix this issue , but im afraid that when I try to get in to tethered cmw it just show this :
================================================== =====================
DEVICE STATUS: FASTBOOT-ONLINE
DEVICE INFORMATION: 56900EFA01 fastboot
================================================== =====================
copy needed files to our device
target reported max download size of 536870912 bytes
sending '/tmp/recovery.zip' (3477 KB)...
OKAY [ 0.384s]
writing '/tmp/recovery.zip'...
FAILED (remote: Bootloader must not be locked)
finished. total time: 0.655s
target reported max download size of 536870912 bytes
sending '/tmp/recovery.launcher' (400 KB)...
OKAY [ 0.276s]
writing '/tmp/recovery.launcher'...
FAILED (remote: Bootloader must not be locked)
finished. total time: 0.545s
we need to stop logcat before replacing it
...
FAILED (remote: command not allowed in this device state)
finished. total time: 0.376s
target reported max download size of 536870912 bytes
sending '/system/bin/logcat' (178 KB)...
OKAY [ 0.269s]
writing '/system/bin/logcat'...
FAILED (remote: Bootloader must not be locked)
finished. total time: 0.537s
issue fastboot oem "stop_partitioning" command to start cwm recovery:
...
FAILED (remote: command not allowed in this device state)
finished. total time: 0.367s
even though the bootloader is not locked , and if i try to unlocked it again in order to enter cmw it says this:
.................................................. .................................................. .................................................. .................................................. .................................................. .............................
C:\Users\Hugo Sanchez\Desktop\IntelAndroid-FBRL-05-16-2015-PTR\resources\platfor
m-tools_aosp>fastboot devices
56900EFA01 fastboot
C:\Users\Hugo Sanchez\Desktop\IntelAndroid-FBRL-05-16-2015-PTR\resources\platfor
m-tools_aosp>fastboot oem unlock
...
(bootloader) Checking unlock authorization.
FAILED (remote: couldn't change state)
finished. total time: 0.309s
I hope some one can help me to fix this
Just a thought but of it drains in a few minutes, something is wrong with the battery or the charger. One possibility is the battery stats are messed up, easy fix is to delete them, but I haven't tried that on lollipop. Otherwise sounds like a return to me... One question, when it drains, does it get smoking hot? If not, battery problem for sure.
dbh369 said:
Just a thought but of it drains in a few minutes, something is wrong with the battery or the charger. One possibility is the battery stats are messed up, easy fix is to delete them, but I haven't tried that on lollipop. Otherwise sounds like a return to me... One question, when it drains, does it get smoking hot? If not, battery problem for sure.
Click to expand...
Click to collapse
Actually it does not get hot when it drains, I believe there is a couple of treads were people are having the same problem after the lollipop update. Don't you think there might be a work around for this ?
I have same problem but cannot find any help ...
Hey all,
basically I ****ed up. I installed 9.0.0.161 through TWRP, forgot to clean everything so naturally while I had Pie running, everything was strange and slow working. When I went to TWRP and format everything (the option where you have to type 'yes'), it couldn't boot.
Now the only thing I can do is flash stuff over fastboot, and I tried flashing the system.img and kernel.img from the BLA-L09C432B157 (8.0.0.157) firmware. It didn't work, and I can't even access eRecovery or anything else than fastboot.
What should I do? I realize this has been my fault for trying stuff out without thinking twice. >.<
EDIT: I should say it's a European Mate 10 Pro (BLA-L09C432)
bump
Flash recovery
E recovery C185 Pİe
Shutdown phone use vol- and usb cable to enter fastboot
Press ENTER key to continue...
Wait FASTBOOT connection....
Replace kernel...
target reported max download size of 471859200 bytes
sending 'kernel' (12882 KB)...
OKAY [ 0.411s]
writing 'kernel'...
OKAY [ 0.063s]
finished. total time: 0.489s
Replace recovery...
target reported max download size of 471859200 bytes
sending 'recovery_ramdisk' (25632 KB)...
OKAY [ 0.804s]
writing 'recovery_ramdisk'...
OKAY [ 0.167s]
finished. total time: 0.992s
Unplug usb cable, use vol+ and power key to enter recovery.
Press ENTER key to continue...
I'm removing the Usb Cable for OK After. Audio Turn On And Power Off Directly into eRECOVERY. Normal does not enter Recovery!
emprazol said:
Flash recovery
Click to expand...
Click to collapse
Did that, still didn't work until now
yunusdemir said:
Shutdown phone use vol- and usb cable to enter fastboot
Press ENTER key to continue...
Wait FASTBOOT connection....
Replace kernel...
target reported max download size of 471859200 bytes
sending 'kernel' (12882 KB)...
OKAY [ 0.411s]
writing 'kernel'...
OKAY [ 0.063s]
finished. total time: 0.489s
Replace recovery...
target reported max download size of 471859200 bytes
sending 'recovery_ramdisk' (25632 KB)...
OKAY [ 0.804s]
writing 'recovery_ramdisk'...
OKAY [ 0.167s]
finished. total time: 0.992s
Unplug usb cable, use vol+ and power key to enter recovery.
Press ENTER key to continue...
I'm removing the Usb Cable for OK After. Audio Turn On And Power Off Directly into eRECOVERY. Normal does not enter Recovery!
Click to expand...
Click to collapse
Well, now I'm in eRecovery, thanks for that. However, when I try to download latest version and recovery, it just tells me "Getting package info failed".. how should I proceed?
Shutdown phone use vol- and usb cable to enter fastboot
Press ENTER key to continue...
Wait FASTBOOT connection....
Replace kernel...
target reported max download size of 471859200 bytes
sending 'kernel' (12882 KB)...
OKAY [ 0.411s]
writing 'kernel'...
OKAY [ 0.063s]
finished. total time: 0.489s
Replace recovery...
target reported max download size of 471859200 bytes
sending 'recovery_ramdisk' (25632 KB)...
OKAY [ 0.804s]
writing 'recovery_ramdisk'...
OKAY [ 0.167s]
finished. total time: 0.992s
Unplug usb cable, use vol+ and power key to enter recovery.
Press ENTER key to continue..
I'm removing the Usb Cable for OK After. Sound Turn on and Power Off Direct into eRECOVERY. Normal Recovery! E does not.