** I will post some pictures later today - I'm at work currently **
The Nillkin Fresh case came about 2-3 days ago and I was quite excited. But that was short lived. The case is a faux-leather flip cover case with a thin plastic shell on that clips to the phone. It looks decent enough, but I have some problems with mine (possibly QC problems):
The case though didn't completely fit!! Along the right side (near the SD/SIM) it is a bit warped - not bad or noticeable unless your looking right at it and for it.
The case is held closed by a magnet, but the magnet on the flip cover is quite small which then requires it to be precisely over the other pole or it does nothing. Not a big deal, but I wish this was thought out better.
Additionally, one of the main features of the case is (link below) how the case being used as a stand. The flip cover is a tri-fold design which should act as a stand but I haven't had much luck with it. The inside of the seemingly leather flip cover is a soft touch, almost suede, material that is quite slippery. This plus the fact that the case seems to be needing to be broken in makes for the "stand" feature unusable... it falls right over currently. (I have tried multiple configurations).
Over all, I bought the case on eBay for $9.99 with no shipping cost (ships from china - companies home country) and it took about 15 days to get here (in the US). Not bad, but I am already looking for a replacement that will make my device feel premium again rather then cheap.
Would I recommend this case? Yes, but only as a temporary case until more come out - like the official Sony cases or a case from Incipio (link below).
** Complete side note: I had a Nillkin case for my old Nexus 4 which only lasted a few short months because the leather started to peel away from the flip cover! I knew this would be a temporary case when I bought it, so keep that in mind!
http://www.nillkin.com/english/proshow.asp?mid=2&sid=0&tid=0&cid=1&scid=13&id=3526&page=1
http://www.incipio.com/cases/smartphone-cases/sony-smartphones/sony-xperia-z-ultra-cases.html
I was fortunate to get to try that case out and many others (being in hk and china) - and I posted about this case. It's unfortunate you didn't read my post and what case eventually went with in the big Z ultra case thread.
This case is definitely not recommended if you want one to work well with desk stand, and want to use the trifold ipad style cover as a stand.
The snap-in style plastic mounts doesn't make it easy to pop in and out of to use the desk stand, and the plastic mounts are shiny thus looks and feels cheap.
Finally, the cover doesn't even come close to the quality and feel of the ipad cover, even the vinyl kind. The material is stiff and plasticky and most importantly doesn't fold together to function as a working stand at all. It will unfold/collapse and fall over.
In addition, there's an issue with the the magnet. With the magnet closed, there is a gap between the last third of the tri-fold cover and the phone's screen. This gap exists because the case (mold or design) is not the right fit - the wider flap makes it essentially unable to align with the opposing magnet. If you try to push the flap down to get rid of the gap, you inadvertently push/slide the magnet off and the cover comes loose. In practice, the magnet will never be engaged because you'll always push the cover down somehow (pocket, bag, stacking something on top).
The only Nillkin I recommend is the http://www.nillkin.com/english/proshow.asp?mid=2&sid=0&tid=0&cid=1&scid=13&id=3516&page=1 shield case. I ended up buying the black one for scenarios where I don't want a flip cover. The fit is good, texture is good (good grippy backside), and it doesn't look too cheap (no shiny plastic). It's decent protection for rougher than usual situations. There are sections where there's a thin piece of plastic on the edge of the phone (like over the usb flap) where it feels weak, cheap and easily breakable. Besides that only issue, I like this case as a back-up.
For a flip cover case that works well with a desk stand, actually stands up, and feels decent quality - I recommend Kaso and Krussell. I went with Kaso as a cheaper alternative for now.
So I guess it's not just me... which is kind of a bummer, but I have already found a replacement. Now if only October 22 was here (my Birthday) I could get a new case!
Thanks for the replay, some good thoughts there!
toonhead85
Funny how the 2 Nillkin cases the OP talks about are the exact 2 I bought online.
I bought the white Fresh, and Yellow leather.
Anyway, after having used both, now I know that flip covers, despite the protection it gives, tend to get in the way of general use. Answering calls involve one extra hassle step.
Taking pictures, you have to roll the flip cover up into the triangle as if you are going to use it as a stand and hold it in your left hand, because simply flipping it and folding it over will obstruct the camera.
Nothing wrong with the build quality...I am sure it is better than most cheapos out there. All the useful ports are left uncovered (one of the reasons why I chose Nillkin...there is actual thought process that has gone into the design). If you want to use the magnetic charging port, not many other manufacturers apart from Nillkin make them uncovered.
The yellow I chose is less vibrant in colour (than what it seemed on screen), and does not go so well with the white ZU I have, so that got retired until the day I get SBH-52 and leave my phone in the bag.
For the Nillkin Fresh, I got in white, and am very happy with it, and currently in use.
It has a nice tight fit, seems to be made of good tough plastic, and the texture on the back helps with general grip.
I did make one modification to it, because even though the magnetic charging port is left open by design, it was impossible to get a good connection while the pone was still in the case. So I cut off the thin strip that runs along the screen side of the mag port. Filed it down with nail clipper file, and now it is perfect. It has not lost structural rigidity.
The number of times that i thought that I had closed the USB port properly, but was still slightly open (thus not making it fully waterproof) has prompted me to get the magnetic charging cable. I knew it was something I wanted while I was out choosing the case, so for those who are still looking for cases, I won't say go Nillkin, but make sure you go for one that has the magnetic charging port uncovered.
Whether you buy DK-30 is a different debate. Some like it, but some find it expensive for what it is. There are not many covers out there tat allow you to dock with it on.
But the USB magnetic charging cable is something I believe every ZU owner should have. For that reason get a cover with the port uncovered.
jewelkobayashi said:
I did make one modification to it, because even though the magnetic charging port is left open by design, it was impossible to get a good connection while the pone was still in the case. So I cut off the thin strip that runs along the screen side of the mag port. Filed it down with nail clipper file, and now it is perfect. It has not lost structural rigidity.
Click to expand...
Click to collapse
Can we please get pictures of this modification? Keen to replicate. Otherwise attractive looking case, be a shame to waste.
liqn7 said:
Can we please get pictures of this modification? Keen to replicate. Otherwise attractive looking case, be a shame to waste.
Click to expand...
Click to collapse
Here u go
jewelkobayashi said:
Nothing wrong with the build quality...
Click to expand...
Click to collapse
I came back to post a quick update about the case I got and this caught my eye... actually the build quality is the reason as well!!
The case is broken ><. On the top left hand side (near the charging port) the case has snapped. A piece is broken clean off and only after about 2 weeks. I know the case was $10, but I also had build quality issues with a Nexus 4 case, so I am going to say the quality is rather low.
With this new information, I am going to say stay away from this case. The long import time (from HK to US), and poor quality aren't worth it. Spend the few extra bucks and get a quality case you will have for more than a few weeks.
Just my 2 cents though...
toonhead85
Related
Just received the $33 FUSE case [http://electroniccrap.com/store/index.php?main_page=product_info&cPath=5_9&products_id=37] from electronicCrap. It is quite a nice case. I really like the finish on both the outer and inner.
The inside is a stiffer type of velvet or something. Not exactly rough, but not as smooth as microfiber for example.
The exterior is very sharp, and business meeting ready. It is a soft suede-like material and is a nice shade of gray. One big advantage of this material is a slightly higher friction grip on surfaces than leather or faux-leather. If I try to slide the tablet in the case on a smooth surface, it is quite hard. I imagine you could set the case on a dashboard and it would rarely slide.
The tablet is VERY secure in the case, and can be made even more secure with a bit of velcro or some other material to fully secure the closing flap. However, with only friction holding the flap, the tablet won't fall out even if I hold the whole thing by the folding cover and shake it.
The case functions well as a stand, sitting comfortably at all three angles on my lap bot sitting and lying in bed. The cutouts for ports are all perfectly sized. The dock port is accessible for something like the HDMI cable. I don't have a dock, so I am not sure if that would fit. The fabric over the microsd and usb slot is put together a little funny. The bottom edge (somewhat visible in this picture from electronicCrap: http://dl.dropbox.com/u/10015338/Cases/hy3.JPG, it is the edge below the microSD cover) sort of tucks in where it should not, and the part that tucks isn't really necessary. This is a really minor thing that doesn't affect the function, just the form a bit. Seems like instead of an oval cut-out of one large connection between front and back panel it should be just two narrow strips.
The comment Steve makes about the magnets on his site is very true. They are a little on the weak side to close the case, but it doesn't bother me at all.
I ordered my Fuse case from electroniccrap.com last Friday and received it three days later. After three months of using my GTab "naked", I have to say it is a much more pleasant experience using it in the Fuse folio case. As ramerco mentions, the case feels well made. My only complaint is that there is no cutout for the charge status LED on the front of the GTab near the charging port. Otherwise, I would not hesitate to recommend this case.
It's a good case for Gtablet.
I have the P3, and I love it as well. Is the only difference a matter of the P3 blocking the left speaker and the flap on top?
If yes, the P3 is a few bucks cheaper and I highly recommend that too.
i think the p3 cutout for the mini usb cover is not lined up properly. i don't know though, i only have the fuse...
imdaman99 said:
I have the P3, and I love it as well. Is the only difference a matter of the P3 blocking the left speaker and the flap on top?
If yes, the P3 is a few bucks cheaper and I highly recommend that too.
Click to expand...
Click to collapse
The P3 is a synthetic leather PU style case that has a "slicker" feel to it.
The Fuse is almost like a suede feel. They are both great cases. I flip back and forth between both of them to fit my mood
And yes, there is a little bit of an overlap of one of the speakers, but it doesn't affect the functionality that much. It still pumps out descent sound!
I ordered the FUSE case as well and it's great. It's a great bargain. I highly recommend it.
Sent from my TnT-Enhanced using XDA Premium App
FUSE - great case for those without a dock.
I read through a dozen or more threads here looking for info on all of the cases that were compatible with the G tablet. The only noteworthy negative aspect of the FUSE case that I could gleen from the experiences of others was the fact that it did not allow the tablet to dock while inside the case - for that you'd need the CLIP I believe. I didn't see any reason to bother with a dock, so I went with the FUSE (from electroniccrap).
Six months later, I'm still happy with my purchase. The material has held up exceptionally well (my 2-year-old got a hold of the case once and didn't manage to leave any visible blemishes or marks, despite his persistence) and I still like the feel of it. The faux-sued or whatever it is offers just the right amount of texture/friction to hold the tablet 1-handed without fear of it slipping out of my grip.
So, I suppose I should say thank you to all of the posters here who shared their experiences with the various cases - much obliged, everyone.
Although not normally a fan of cases for phones, I've now dropped my Atrix a few times (due to the hopeless shiny back with a total lack of grip) so I've decided I need to get one! Luckily, the Atrix has only been dropped onto carpet so it remains undamaged.
I don't like the silicone cases and I'm not overly keen on the TPU ones either. The 'official' rubberised battery cases looked like the right sort of thing, but after checking the reviews, I'm not keen on the way the side bits on the front can come loose when coming in or out of the pocket.
As I'm looking for something slim/lightweight, I think this leaves me with either the Seidio Surface or the Incipio Feather.
My questions is this: Regardless of the amount these cases protect the phone in case of being dropped, are they actually likely to help me to avoid dropping them? Do these cases improve the 'grippability' of the Atrix?
Any helpful comments are appreciated!
I used the Incipio Feather for a few months. I really liked the "low-profile" but it was very fragile. I ended up cracking two of them just from taking them off to do battery pulls. As far as grip goes, it was generally nice to hold but doesn't offer that much more grip then the phone by itself. I've also used the Ballistic SG and while it was too bulky for me it had excellent grip. I was able to put it on my lap, back facing down, while driving and it never moved.
Currently I use the Speck Candyshell and it holds up pretty well. Grip can become an issue if your palms get sweaty as the exterior is all hard plastic.
Maringer said:
Although not normally a fan of cases for phones, I've now dropped my Atrix a few times (due to the hopeless shiny back with a total lack of grip) so I've decided I need to get one! Luckily, the Atrix has only been dropped onto carpet so it remains undamaged.
I don't like the silicone cases and I'm not overly keen on the TPU ones either. The 'official' rubberised battery cases looked like the right sort of thing, but after checking the reviews, I'm not keen on the way the side bits on the front can come loose when coming in or out of the pocket.
As I'm looking for something slim/lightweight, I think this leaves me with either the Seidio Surface or the Incipio Feather.
My questions is this: Regardless of the amount these cases protect the phone in case of being dropped, are they actually likely to help me to avoid dropping them? Do these cases improve the 'grippability' of the Atrix?
Any helpful comments are appreciated!
Click to expand...
Click to collapse
I had the feather. After two drops on different corners, the case had cracks. I expected as much and the case did its job. I got the Incipio silicrylic case as a replacement, which has a silicon cover AND a hard cover. It's slightly bulkier than the feather, but it still looks good and is definitely more sturdy. Case is grippy but not overly grippy where you have a tough time putting the phone in your pocket. I can remove the case without fear of cracking it, unlike the feather.
I had one of the Incipio Feather's also. It lasted about 2 months before it completely fell apart. Is is a nice case and I really liked the feel and look of it and it will fit in the car dock with a little modification. But it is not rugged enough for me to recommend. I am using a TPC case now. Does the job. Easy to remove to put in my Car Dock, LapDock or Standard Dock. It feels much better than the Atrix does by itself. But it is kinda ugly. But I have dropped it a few times and it keeps my Atrix safe.
The Seidio Active was my choice and I like it a lot. Two pieces - rubber with hard shell skeleton protects it nicely.
I can remove it (to dock) in seconds and replace it quickly too. Got it at Amazon: http://www.amazon.com/gp/product/B004WKIEF2/ref=oh_o03_s00_i01_details
That's the sapphire blue one, but they have other colors.
I'm using the otterbox commuter case. I got it off of Amazon.com for only 20 bucks on Saturday. So far it's been amazing
Sent from my MB860 using XDA App
When talking about cases, would it be possible to mention (as some of the posts do) which docks these work with (I use all the docks...car, HD/standard docks, lapdock). Also a link to some site with the product or a good enough description that I can google it.
I hate to be a pain in asking for the extrra info, but I'm looking for a case now, too and don't want to have to remove it all the time (especially for the car dock).
Of all the experiences I have read about cases and their compatibility with docks, the only one that I have heard that works is the Incipio Feather (or somehting similar) when taking in the consideration of actually not removing the case.
troycarpenter said:
When talking about cases, would it be possible to mention (as some of the posts do) which docks these work with (I use all the docks...car, HD/standard docks, lapdock). Also a link to some site with the product or a good enough description that I can google it.
I hate to be a pain in asking for the extrra info, but I'm looking for a case now, too and don't want to have to remove it all the time (especially for the car dock).
Click to expand...
Click to collapse
Is this the one:
http://www.amazon.com/Incipio-Motorola-Atrix-feather-Ultralight/dp/B004QJPWK4/ref=pd_cp_cps_1
Yes, I have read that people just simply remove the insert that is in the docks and it fits just fine. I have seen pics before too but can't remember where I saw them. Maybe I can try to find them.
troycarpenter said:
Is this the one:
http://www.amazon.com/Incipio-Motorola-Atrix-feather-Ultralight/dp/B004QJPWK4/ref=pd_cp_cps_1
Click to expand...
Click to collapse
---------- Post added at 11:29 AM ---------- Previous post was at 11:16 AM ----------
Here is a thread about a mesh cover (which is essentially the Feather but with a mesh look) and the second link is a post of someone in that thread showing the Atrix in the car dock with the case on.
Thread:
http://forum.xda-developers.com/showthread.php?t=1194096
Post with pics:
http://forum.xda-developers.com/showpost.php?p=16704009&postcount=27
Here is another thread discussing (and maybe confirming) the Feather working with docks:
http://forum.xda-developers.com/showthread.php?t=982574
The Incipio feather will fit in the car dock with the cardock insert removed, but the latch wont close. It has a ridge that comes over the face of the phone, but sits on top of the feather case. It will work if you make sure you have it inserted firmly all of the way in. I take corners pretty fast and had it fall out a couple of times. I modified mine to make the latch close pretty easily. Put it in the cardock and marked the outline with a X-acto knife. Used diagonal cutters to cut the 2 short vertical cuts. Scored the Horizontal mark with the X-acto knife and snapped the piece off with some lineman pliers. Now that these are $10 apiece I am tempted to get another one (or 2). Just was not worth the 25 bucks I paid 6 months ago.
Thanks for the various comments about cases.
I've looked at the various recommended cases and think I'll probably have to give the Incipio Feather a miss if it is as fragile as others have mentioned. I'm based in the UK so I'd have to order the case from the US (can't locate a UK seller) and this would cost me the equivalent of around US $ 45.00 which is a bit too much for something which won't last long!
Various other hard cases aren't available in the UK either (or not at decent prices) and, for me, the most important thing is to have a case lacking in bulk.
The Otterbox Commuter is the only one I get can get reasonably cheaply from within the UK (about US $ 20) but I'm not taken by the look of this.
Therefore, I think I've settled on the Seidio Surface which looks to have good reviews and will hopefully be the sort of slimline case I can deal with. I can obtain this via Amazon UK from a US seller for a mere US 36.00!
Incidentally, in the monster "Ruggedized battery cover" thread, there was mention that the Seidio Surface fits the lapdock and can be easily removed for the car dock:
http://forum.xda-developers.com/showpost.php?p=16600986&postcount=379
I don't own either dock so this isn't really of relevance to me!
I started looking for a discrete case for the same reason (battery door is way too slippery.)
There were some Chinese-made rubberized battery door replacements that seemed popular a while back. Most of the mobile accessory sites that carried them sold out, though I found and ordered one on eBay. The seller seems to have more:
http://www.ebay.com/itm/Back-Cover-...ltDomain_0&hash=item415bd6c69c#ht_2880wt_1085
I just got my yesterday. Fitment is surprisingly accurate, no misaligned cutouts or anything, and the added bulk is acceptable. Feels much better in hand now, too, when typing in landscape mode. It takes a deliberate effort to free the phone from the case, as it has a couple of tabs that clip into the retaining slots used by the factory battery door. Haven't noticed it snagging or coming loose as it goes in and out of my pocket either.
edit:
I just noticed the "dock fitment" discussion going on in this thread. I can't say anything about this case + docks since I don't own any docks.
I fashioned a case out of 3M carbon vinyl wrap. Keeps that Carbon Fibre effect on the back case whilst making it much more grippy (never dropped it since) and much more aesthetically pleasing as it gives off a 3D carbon fibre effect.
I can post pics if you like
Also worth mentioning you can pick this stuff up dead cheap off eBay - http://www.ebay.co.uk/itm/30x20cm-G...arParts_SM&hash=item4cf189dd66#ht_1792wt_1163
This sheet will give you a few attempts at it. It took me 2 to get mine the way I liked it
If you are just looking for grip without affecting aesthetics the Zagg Total protection is a great option. Clear is nearly impossible to tell it is on there. It is the same material and install as the screen protector. So no residue when removed. Make sure you read/watch the install tips from Zagg. I have been using it since April without a drop.
I have; however, decided to get a case and am trying the Seidio Active. The wife got the Incipio Silicrylic. both indeed fit in the HD/Standard Dock with the insert removed, I'm curious about whether there is enough support from the back of the dock though. As mentioned, I'm guessing the car dock will not close due to the extra couple millimeters, but will try it out and reply if it does indeed work.
Well, the Seidio Surface winged its way across the Atlantic reasonably quickly and I received it earlier this week.
It is very slightly bulkier than I expected but it is still very slimline so this isn't a problem as it still fits in my pocket easily. A little more difficult to take the phone out of my pocket than previously but again, not really a problem.
The surface of case itself isn't as 'grippy' as I expected, either, but it is a great improvement to the usual slick battery cover and I haven't juggled with it yet this week! I can now operate the phone using one hand if necessary without fear that I will lose my grip and drop it.
There are a few small imperfections on the back of the case - it would seem as though there were a few specks of dust or some other substance on the case before it was covered with the rubberised coating as a few tiny bumps can be felt. Not enough of a problem for me to bother returning it all the way to the US, however!
It is slightly tricky to take the Seidio Surface off the phone - it seems to come off easily sometimes but remain stubbornly in place at others. I think I'll need to practice taking it on and off the phone a bit more until I get the knack.
Overall, I'm reasonably impressed with the case and would give it an 8/10. It would have received a higher score had it not been so ridiculously expensive for me to buy here in the UK - Amazon.com are selling it at approximately half the price I paid!
Purchased the SiKai MicroFiber case for the Lenovo IdeaPad K1 Tablet. Delivery was within the UK and didn't take too long, about 5 days including the weekend.
I paid £15.19 delivered from Ebay UK Item number: 200647561882
The case is made from a strange type of plastic material, it's quite soft and flexible. Am kind of glad rather than faux leather. It is very thin and light, but seems sturdy enough to protect the tablet around the house. I have a 10" netbook bag that I keep it in when travelling to add extra protection.
I like it since it makes it easy to carry around with you and doesn't add bulk to it. I would say the case is lighter than my official HP Touchpad case and similar in strength, although a different material. I can only compare it to the ROOCASE Multi-Angle Leather Case and can say it is much thinner and lighter than that.
There is only one angle that the case allows for, but since it is an Android tablet you can flip the whole thing round and get a lower angle. Its fine for watching at night when streaming video so its not an issue for me.
Price wise the only options available to me at the time were the faux leather ones for about £9.99 or the official case from the Lenovo website coming in at a hefty £34.99 once you add the crazy £10 delivery charge! Not many options in the UK unfortunately but am glad I did some research and found this case.
Other things that you might notice in the photos (sorry poor camera phone ones) there is a place to put a pen, all cut outs seem correct and I love the fact that I can charge it without having the case open, also the hdmi port is free.
Not sure how long it will last but considering the few days usage of it, the minor things like the tablet can slide a tiny bit inside the case so would have preferred a tighter fit (although will try and adjust the velcro again that closes once you slip the tablet inside), the cut out by the front facing button could be a bit lower, and the magnetic clasps to be quite weak I will give this case an 8/10 and can recommend it.
http://www.ebay.co.uk/itm/SiKai-MicroFiber-case-Lenovo-IdeaPad-Tablet-K1-case-/200647561882
great case! I bought this sikai case too and actually prefer it more than the original lenovo K1 case.
This covers all ports, and also has a great microfiber texture that is slightly grippy, while remaining smooth to the touch. does not attract dust at all and keeps the K1 snug (if it feels loose, readjust the velcro tighter).
recommended!
Yeh have tightened it a bit more, doesn't move as much.... Glad I chose this over the cheaper cases and the official one which was more than double the cost here in the UK.
Can't believe how dead this forum is for this tablet, going to see if there are anymore forums with more support....
Just got this tab last week and love it so far. Looking for a good case but hate the leather, faux leather look.
Please let me know if you find more forums as I have looked and am surprised how little I've found....
I know of one other decent one, google "lenovo community K1"
viggs74 said:
Just got this tab last week and love it so far. Looking for a good case but hate the leather, faux leather look.
Please let me know if you find more forums as I have looked and am surprised how little I've found....
I know of one other decent one, google "lenovo community K1"
Click to expand...
Click to collapse
Cool will do.
This case is pretty good if you want something thin and light, there are stronger/more protective cases out there but they add bulk and I don't want that since I use this round the house...... Still glad I bought this case and find it better in that respect to the Roocase.....
Thanks, will google what you said.....
Got the SiKai for my TPT. Everyting else looks bulky in comparison. It is extremely thin (I''ve tried a lot of gadget cases over the years), and although it's screamingly vinyl, it doesn't look really cheap since it fits so well. Leather like this might come off as over-the-top (not that I wouldn't probably sucker into that if I could find it). It's got the seam around the edge where it cushions a drop, and the magnetic closure on the flap is a great touch, not too powerful, but it stays closed well enough.
My gripes are with the screen cover flap: it leaves two stripes on my matte screen protector where the fold places rub off the grease I thought I cleaned off last night, it doesn't hold the tablet vertical enough to really use, and it's busy looking on the front. If I had a choice in the design, I would leave off the "stand" capabilities and leave it flat. If it's open, it's really floppy; it would be easier to manage if it were entirely rigid. I might add a hide-able tether & a knob/button so you could stand it up on its other edge more vertically instead.
All in all, for the price I paid (US$26-ish), I'm very happy with it. If Piel Frama comes up with something, though, I might check that out, if only to drool. I still love my old Wizard case, and my Advantage case from them, too. Very lovely, solid product, and they've been keeping customers happy for a long time.
Addendum: After a couple of months with it, mine is holding together just fine. I had to trim a bit of vinyl fringe, butvall vinyl does that ( it frays a bit after it's freshly cut, but after you trim it once, unless it's cut really crooked, you're done). I have noticed that after a bit of stretching from the daily+ in & out I do to use the dock, it's loose enough to partially obscure the rear camera, not to mention trying to take pics with the flap cover is a huge PITA. If I used this camera a lot, I'd be totally fed up with this case. I may also be melting a bigger hole for the speaker (whch is hard-core disappointing to begin with). All in all, though, that's it for my complaints, which is pretty rare for me.I plan on cloud storage sync and a great cam on my next phone to use the tab for pviewing,
To be fair the official HP Touchpad case does the same thing to my Touchpad so it's one of those things.
I use the same case for my Thinkpad Tablet, and it's the best I've encountered so far, albeit with some flaws of it's own: Some of the stitching on the inside of the cover is already beginning to fall apart after ~1 Month of usage :-/
Stitching has been fine on mine, maybe tell the reseller to exchange it?
Wow cool.... but its little bit expensive
Hi all,
Here is my review of the Sikai leather/plastic case, as sold by Amazon. For comparison, I have had my Prime in the Poetic cover since I got it. It was okay, but didn't have a charging slot in the spine so it had to be open to be plugged in - plus the nearly-flat angle was nearly-useless because the cover kept slipping out of the tab you tucked it into. I had ordered the GreatShield folio case, but returned it because I didn't like the way the case gripped the tablet, plus I didn't like that to close the cover I had to put pressure on the screen to slide the clip past the edge.
Onto my review...
As mentioned in other reviews, it is a strange mix of black leatherette and dark brown plastic. The plastic back plate is great - the Prime snaps in and seems to be held quite securely. Similar to many iPad covers, it just wraps over the edge - enough to hold, but out-of-the-way enough to really reveal the sleek Prime look. The main portion of the back plate is the black leatherette material, with only the outer edge showing the brown plastic. It has all of the necessary cutouts - including (apparently) the ability to have the dock attached and still close the cover. That is because the "hinge" pieces that connect the cover to the back plate are elastic. I don't have a dock, so I can't comment much on that.
The leather-ish cover looks to be two pieces glued/sewn together, with two bends in the midde - allowing it to be folded up in a triangle shape. Both angles I tried seem to be reasonably stable while typing. About the two layers of the cover...they might have been able to get away with only one, giving it a sleeker appearance, but they had to account for the strap that slips over the sides to hold the cover against the screen. The strap is fine, and gives it an upscale look, but I would have preferred a more unobtrusive solution with magnets or something similar. Overall, the case is skinny enough - just about the same thickness as my Poetic case. That is actually a bit of a downer since I expected this to be thinner since the Poetic case has that layer around the bezel with the magnets in the corners.
There are a few tiny fit-and-finish things that I didn't expect to see in a $30 case. The leather part of the back plate doesn't always make a perfect fit with the plastic border. I'm really nitpicking here, but when this costs three times as much as my Poetic case, I was expecting Ferrarri-quality stuff. I know - it still only $30 so I won't beat them up (much) for it.
Overall, I really like the Sikai. It has a superior look to the Poetic - that one hid all of the nice features of the Prime underneath the protective layers of the front/back/cover. When all that is exposed is the center part of the screen, it almost doesn't matter anymore what Asus designed it to look like. The Sikai shows the Prime's lines and curves much better than the other cases I have seen. The plastic seems tough enough to not break or wear any time soon, so as long as the leatherette holds up, I say this is the best case available for the Prime under $30...
By the way, when ordering from Amazon, it ships from Hong Kong. I placed the order on June 18th, and got a confirmation within 24 hours that it had shipped. However, the confirmation email said my ETA was JULY 31st! Needless to say, I was very happy when it arrived today instead...
I figured there were already better pictures available than my crappy phone can provide, but I can take some close-ups of specific features if requested.
Thanks!
swordsman74 said:
It has all of the necessary cutouts - including (apparently) the ability to have the dock attached and still close the cover. That is because the "hinge" pieces that connect the cover to the back plate are elastic. I don't have a dock, so I can't comment much on that.
Click to expand...
Click to collapse
The dock works great with this case!
yeah I've had this case for a few weeks and its very functional. I really like how it doesn't cover the bezel on the prime like the sikai fiber case and you get multiple angles that actually work
My only complaints are that its a bit on the heavy side and because its designed to be put into the dock with the case on, the steepest angle isn't quite as steep as other cases because the flap slides out making the "hinge" not at the fold but an inch out
oh and the case is kind of ugly haha
Just got my cover in the mail today. Unfortunately it leaves a bit gap at the bottom where the USB port is. Anyone else got this cover and have the same issue? Also the buttons are a bit stiff.
deadman3000 said:
Just got my cover in the mail today. Unfortunately it leaves a bit gap at the bottom where the USB port is. Anyone else got this cover and have the same issue? Also the buttons are a bit stiff.
Click to expand...
Click to collapse
Yes, mine is pretty similar.
I can live with it, it is quite a decent case for the cash and I like the stiffer buttons as they help to prevent 'pocket presses'
bisto321 said:
Yes, mine is pretty similar.
I can live with it, it is quite a decent case for the cash and I like the stiffer buttons as they help to prevent 'pocket presses'
Click to expand...
Click to collapse
Ah! OK that's interesting to know. My main concern was it being a weak point during a drop (like if something hitting it square on the front edge). It's a shame it's not just a little more snug fitting as it would be perfect otherwise. The main reason I got this case instead of a standard TPU is so I can put the metal plate for my magnetic car phone holder behind the plastic back which works really well. I do notice when putting the USB cable in the phone can shift slightly up and down in the rubber housing. It's just a fraction longer than it should be. I have also ordered the Brotect screen protector after trying some other brand that is absolute carp! I am waiting on a refund for those (ordered 3 of them in case I messed up the first). I also have an issue with garbled voice on calls but not sure if that is down to my network or not yet.
Also the lack of accessories is rather depressing.
But that's what happens when you don't follow the iPhone/Samsung crowd.
Fun and games eh?
deadman3000 said:
Ah! OK that's interesting to know. My main concern was it being a weak point during a drop (like if something hitting it square on the front edge). It's a shame it's not just a little more snug fitting as it would be perfect otherwise. The main reason I got this case instead of a standard TPU is so I can put the metal plate for my magnetic car phone holder behind the plastic back which works really well. I do notice when putting the USB cable in the phone can shift slightly up and down in the rubber housing. It's just a fraction longer than it should be. I have also ordered the Brotect screen protector after trying some other brand that is absolute carp! I am waiting on a refund for those (ordered 3 of them in case I messed up the first). I also have an issue with garbled voice on calls but not sure if that is down to my network or not yet.
Also the lack of accessories is rather depressing.
But that's what happens when you don't follow the iPhone/Samsung crowd.
Fun and games eh?
Click to expand...
Click to collapse
Good idea for the use of the removeable plate.
Yes, bit disappointing about accessories - but the phone is great.
I have a Nillkin hardcase and a Nillkin flip case too - both really good and much slimmer fit than the J&D, but they offer less protection, so I will stick with J&D for now
I have the Incipio version of that case style, it fits great.
http://www.incipio.com/cases/smartp...cases/dualpro-case-motorola-droid-turbo2.html
How thick does this make the phone