after a call I see a screen that tell me "if I want to sent message or call again etc".
someone know how to disappear this screen ????
I just want to press the red button and the phone go to home page
Why not just press the home button?
gx3k said:
Why not just press the home button?
Click to expand...
Click to collapse
If I press the home button dont stop the call.so if I end a call I have to press the red button(to be sure that the call finished)and then the back button to go out of this ungy screen. I just want to press one's the red button and go to home page.
rodosman said:
If I press the home button dont stop the call.so if I end a call I have to press the red button(to be sure that the call finished)and then the back button to go out of this ungy screen. I just want to press one's the red button and go to home page.
Click to expand...
Click to collapse
I end calls by pressing the power button then go to the homes screen by pressing the home button.
Related
Hey everyone
as the title says, how can i re enable back button on Clockwork?
it used to work then mustve pressed up*/down on volume rocker a flukey amount of times to shut it off
what is the combo to re enable it ?
thanks then
you have to scroll through the menus a couple of times using the volume buttons till it appears on the screen "back button enabled".
Hope that helps
ricey1986 said:
you have to scroll through the menus a couple of times using the volume buttons till it appears on the screen "back button enabled".
Hope that helps
Click to expand...
Click to collapse
Thanks mate, got it working now....although the home button now seems to work as down ....ill sort that later tho
cheers guv
ricey1986 said:
you have to scroll through the menus a couple of times using the volume buttons till it appears on the screen "back button enabled".
Hope that helps
Click to expand...
Click to collapse
You can achieve the same result with tapping several times the "menu" button (the left touch button) until you'll see the "back button enabled" notification on screen.
Issue: I have a galaxy S4 that has a bad LCD. The LCD itself functions. However when the phone is locked and the screen is off, when I click the power button, the screen doesn't come back on. But if I click the power button again to lock it and click the power button again to unlock it, the screen will come back on after the second time.
So what I'm looking for is an app or mod that will allow me to map either the power button or even double clicking menu button to have the action of clicking the power button 3 times. Any advice? Thanks!
Hello so I've noticed sometimes when I'm in an app, say chrome, or a game and I press the home button it always takes a few seconds for the press to register and go back home. Is there a way to get rid of the home button lag?
NoFanboy said:
Hello so I've noticed sometimes when I'm in an app, say chrome, or a game and I press the home button it always takes a few seconds for the press to register and go back home. Is there a way to get rid of the home button lag?
Click to expand...
Click to collapse
this is because of the double tap home button to open the camera, at least most likely, it means the phone waits a moment to check for the 2nd press of the home button before treating it like a single home button press.
This can be disabled by going into the camera, then camera settings, then turn off "quick launch"
How to enter Recovery mode in intex Irist, please please please help me some one.
Probably it's too late to reply but it may help somebody else so here it goes...
Turn off your watch phone. Wait till it's completely off and some more time. Then, press the bottom button and top button simultaneously until you land on the recovery screen. Basically you can first press the bottom button, keep it pressed and then power the watch phone with the top button, as you normally do, while the bottom button is pressed.
In the recovery mode, as far as I remember, the bottom button is used to scroll the cursor down and top button is used to select. Cursor goes back to the top when the end of the list is reached and then comes down in cycle.
Addy11 said:
Probably it's too late to reply but it may help somebody else so here it goes...
Turn off your watch phone. Wait till it's completely off and some more time. Then, press the bottom button and top button simultaneously until you land on the recovery screen. Basically you can first press the bottom button, keep it pressed and then power the watch phone with the top button, as you normally do, while the bottom button is pressed.
In the recovery mode, as far as I remember, the bottom button is used to scroll the cursor down and top button is used to select. Cursor goes back to the top when the end of the list is reached and then comes down in cycle.
Click to expand...
Click to collapse
It goes in test mode not in recovery
Anyone know how to make the button presses that you map on your kunai not show? I layout the buttons and make that invisible, but when I hit the button it flashes the button press on screen. I'd like to make it so I don't see my button presses for a full screen experience without crazy button flashes.
I just uncheck the display hotkeys configuration option.
I have a picture but it won't let me upload it.
https://i.imgur.com/Whkjpoq_d.webp?maxwidth=640&shape=thumb&fidelity=medium
iBluesurge said:
I just uncheck the display hotkeys configuration option.
I have a picture but it won't let me upload it.
Click to expand...
Click to collapse
Yea but when you hit the button it shows up on the screen. That's what I'm talking about. I hate the button flashing and analog stick showing up while playing fullscreens.