Hi all,
i got an bootloop at my Presitigo PMP5580C (same as Intenso TAB 814). The recovery mode (Power + vol+) wont work.
How to flash the firmware to the tablet?
I installed Android SDK and the Drivers. But what to do now? What Software did i have to use to flash und what file (Firmware) to flash?
Please help me...
Regards
Hi,
any ideas? I need your help...
I also have such a problem with my PMP5580C DUO.
It just hangs on the Bootscreen with the "The Art Hi-Tech" and the logo.
No chance to get into cwm with power+vol up and even the Hardresetbutton just switches the tablet off.
Can someone help? Or did you find a solution yet?
Thank you very much
W3hrWolf said:
Hi all,
i got an bootloop at my Presitigo PMP5580C (same as Intenso TAB 814). The recovery mode (Power + vol+) wont work.
How to flash the firmware to the tablet?
I installed Android SDK and the Drivers. But what to do now? What Software did i have to use to flash und what file (Firmware) to flash?
Please help me...
Regards
Click to expand...
Click to collapse
Have you tried to put the update.zip file and recovery image on an SD card ?
If not do that then press (Volume +) + (Power) buttons then when the screen flashes stop pressing the (Power) button and keep pressing the (Volume +) button after some time it will start flashing the Tab.
Here is the link if you don't have the update.zip file :
http://www.prestigio.com/catalogue/Archive_products/Multipads/MultiPad_8.0_Pro_Duo#/product-support/firmware
use the 2.0.24 version.
Hope this helps
If not tell me so I can give you another way by using CWM.
Waiting for your reply...
pmp5580c bootloop
Zacktamondo said:
Have you tried to put the update.zip file and recovery image on an SD card ?
If not do that then press (Volume +) + (Power) buttons then when the screen flashes stop pressing the (Power) button and keep pressing the (Volume +) button after some time it will start flashing the Tab.
Here is the link if you don't have the update.zip file :
use the 2.0.24 version.
Hope this helps
If not tell me so I can give you another way by using CWM.
Waiting for your reply...
Click to expand...
Click to collapse
Hi, my friend has the PMP5580c and it too will not go to recovery at all. it just hangs in a boot loop on the start up screen. I have tried the recovery combination, but it does not work. how would I go about flashing the firmware/update.zip file using CWM.
AzahTabor said:
Hi, my friend has the PMP5580c and it too will not go to recovery at all. it just hangs in a boot loop on the start up screen. I have tried the recovery combination, but it does not work. how would I go about flashing the firmware/update.zip file using CWM.
Click to expand...
Click to collapse
Do you have a CWM flashed already or not?
If so then I had this problem before you just need to put the update.zip on the root of the SD card then press the recovery buttons for some time like 2 minutes -some times it takes so long but it works- .
reply to me soon.
Bootloop fixed
Hi Zack.
I was able to get it sorted with fastboot. Needed the laptop to register the m3-chip that it was saying was the tablet. Once that was done, flashed it with the original stock firmware. It now runs like it was brand new.
Thank you all for your time on this matter
AzahTabor said:
Hi Zack.
I was able to get it sorted with fastboot. Needed the laptop to register the m3-chip that it was saying was the tablet. Once that was done, flashed it with the original stock firmware. It now runs like it was brand new.
Thank you all for your time on this matter
Click to expand...
Click to collapse
hi, i have the same fault on the same tablet, how do i fastboot? also when connected to pc it is saying it is a world cup device? thanks in advance
Bricked PMP5580C
Hello
I have bricked my Intenso Tab 814 (same as Prestigio PMP5580C). I formated the bootloader space + the recovery space, and now I can't even turn it on. The backlight of the display isn't glowing up at least. So I used my MicroUSB cable and connected to the computer, it is recognized by the computer, but I can't flash anything back with the amlogic software which I've got, I am really appreciating when someone of you can try to help me out,
thanks in advance,
AMLOGIC
Unbricked Intenso Tab 814
I have successfully unbricked an Intenso Tablet 814 also know as Prestigio PMP5580C! It had no bootloader and all partitions were formatted! This includes the bootloader, means it even showed backlight as I plugged it into the power supply. I got a rescue sd card made with Christian Troys tutorial but my tabket was nit abke to start, because the nand chip was corrupted, so I looked at the nand chip and used a scrwwdriver and put it on the 6 and 5 th point t the right side on the left side is the hole on the nand chip, after that I was able to permitt the access for the nand chip to the mainboard, so it booted from the sd card automaticaly,
Intenso Tab 814 can be unbricked! Yeah, now I need it's source to customize the recovery and boot splash + oneday the os,
Take care!
Bye bye!
Stuck in bootloop intenso tab 724
So the title says it all how can I fix it? No custom recovery only root
Related
Hey guys.....
This is pretty much my first thread . I have got a Chinese android tablet called HSG MIDX5A Telechips Tcc 8902 (a.k.a. Herotab RK7, Pandawill G11 1st model) with ARM1176J2 chip.
What I did yesterday is that I tried to get it into recovery mode and then somebody on IRC assisted me to flash the tablet with the recovery image using fastboot and then I got the recovery mode <3e> working but I was not able to navigate through the recovery menu using the home, back and menu buttons. However I do not have any Vloume up /down keys with this tablet .
BUT this is not my problem now. After I failed to navigate through the recovery menu I decided to flash a new lk.rom file using FWDN V7 2.13 and that went fine but as you guys know I need to flash the tcc8902_mtd.img after that. Here is the problem I want to get into the FWDN mode to flash the tcc8902_mtd.img but I`ve been trying since yesterday and I was not able to go into FWDN mode. My tablet is not booting too normally. I`ve tried to make the splash screen "I love you " to still there but no hope. I`ve tried the home+power button and also power+touch the center of the screen also did not work too. Whenever I release my finger out of the power button it just turn off.
So please what do you guys suggest ???
Alternatve method ?
I heard about USB Host boot mode or is it no longer needed even in my case ?
What about this ?
I am really sure that I flashed the right rom.
Again I am really struggling on how can I put the tablet in FWDN mode, however I tried the combination you just mentioned and it did not work for me . Yeah something happened to me yesterday that I tried to push the middle of the screen but firmly and really hard at the same time I hold the power button and finally the splash screen"I love you" freezed as it should be but I was not able to get it detected by FWDN V7 2.13 ? Am I doing something wrong ?Should I switch to windows xp 32 bit ? I am using windows 7 64 bit which I had to hack the drivers in order to get the tablet detected at the first beginning before I flashed the lk.rom file so please help
I've got an MSI Windpad Enjoy 10" Plus (http://www.msi.com/product/windpad/Enjoy-10-Plus.html) and I tried to flash it this ROM (http://forum.xda-developers.com/showthread.php?t=1540616).
The rom is for MSI Windpad Enjoy 10", while mine is called Enjoy 10" Plus. So GG, I think I got owned. So retarded you don't even have to tell me.
Now whenever I try to turn on the tablet, it would simply vibrate, show the logo and then turns off. PC doesn't detect it.
However, I tried holding Power button + Reset button together, the PC detects it, but it's unknown and it can't identify it (even though I have MSI's drivers installed and all).
...Any ideas on how to overcome it?
I'm going to sleep now, and will check tomorrow. Thanks in advance.
[UPDATE] 2/22/2013 11:00pm gmt
I'm able to boot it only if I have it plugged in. I can only use Power + Volume controllers + Reset buttons. I can enter Recovery Mode but I cannot confirm/click on any selection.
Tablet does not get recognized by the computer in "Flashing Mode".
I forced to install the driver for the "Flashing mode" when the tablet is in recovery mode but programs like MSIFlashtool, RKBatchTool, RKAdnroid. (not sure if i correcly used the last 2... but whatever)
spilot said:
I've got an MSI Windpad Enjoy 10" Plus (http://www.msi.com/product/windpad/Enjoy-10-Plus.html) and I tried to flash it this ROM (http://forum.xda-developers.com/showthread.php?t=1540616).
The rom is for MSI Windpad Enjoy 10", while mine is called Enjoy 10" Plus. So GG, I think I got owned. So retarded you don't even have to tell me.
Now whenever I try to turn on the tablet, it would simply vibrate, show the logo and then turns off. PC doesn't detect it.
However, I tried holding Power button + Reset button together, the PC detects it, but it's unknown and it can't identify it (even though I have MSI's drivers installed and all).
...Any ideas on how to overcome it?
I'm going to sleep now, and will check tomorrow. Thanks in advance.
Click to expand...
Click to collapse
i dont think that that is called brick
anyways go download Odin and the stock image for your phone (in tar format)(just search on XDA)
put phone into download mode nd open odin
select PDA and select the tar file u downloaded
click start and it should take u back to stock
forgot if this unroots ur phone or not so u might have to root again.
Jack Jake said:
i dont think that that is called brick
anyways go download Odin and the stock image for your phone (in tar format)(just search on XDA)
put phone into download mode nd open odin
select PDA and select the tar file u downloaded
click start and it should take u back to stock
forgot if this unroots ur phone or not so u might have to root again.
Click to expand...
Click to collapse
This is not Samsung or a phone. Read what you are told
If you have a splash screen, you are not bricked. Does adb recognise your tablet? Can you access any recovery/download mode?
Sent from my ARCHOS 80G9 using Tapatalk HD
Quinny899 said:
This is not Samsung or a phone. Read what you are told
If you have a splash screen, you are not bricked. Does adb recognise your tablet? Can you access any recovery/download mode?
Click to expand...
Click to collapse
ADB doesn't recognize it. I tried holding Power + Reset button and did 'adb devices' on Ubuntu and it didn't show anything. On Windows, if I held these 2 buttons, it would show an unknown device in Device Manager. (Mind you, I don't have the Android SDK on Windows, just Linux.)
I can't access any recovery/download mode. Any combination of buttons (Power+VolDown, Power+VolUp/VolDown, Power+VolUP, Power+Home, Power+Back, Power+Settings) would do nothing.
-----------------------------------------------------------------------------------------------------
This what it does when I press Power + Reset Button with a needle. It boots up, splash screen, and stays on black screen (Btw, in this stage, it's Unknown Device in Windows Manager).Once I let go of Reset or Power button, it shuts down.
Turning it on without holding Reset, it would show splash screen, black screen and turns off in about 2 seconds.
Bump.
I've tried playing with it for some time. I can't get it to stay working without pressing power+reset buttons, it always shuts off...
Go to the device website, and download section, get the latest firmware and forget to download the flash driver.
Follow the steps that in firmware folder after unzip it, and you'll get your tablet on
Sent from my Enjoy 10 Plus using xda app-developers app
mramzi said:
Go to the device website, and download section, get the latest firmware and forget to download the flash driver.
Follow the steps that in firmware folder after unzip it, and you'll get your tablet on
Click to expand...
Click to collapse
... I was trying all the time to get it work on the PC without plugging the charger. Anyways~
(Tablet's turned off), I plugged charger, I plugged USB, I turned on the tablet and viola it actually worked and booted into OS. However, no buttons work AT ALL, and touch input doesn't work as well.
I tried to get into Recovery Mode and it worked, but I can go up/down using VolUp/VolDow buttons but I cannot click on any thing because the home button don't work nor any other.
Only Power + VolUp + VolDown + Reset buttons work... What to do now?
TL;DR I want to click on 'Update from SD Card' from the Android Recovery but I couldn't get the 'home' button to click enter on the selection. So what's the solution?
bump.
updates:
I tried to place the firmware from the official website as update.img on an SD Card and placed it in the tablet and went into the recovery mode and selected the 'update from sd card' but i couldn't click it. I tried to tap power, home, search, settings and back and nothing worked.
what I've got up until now:
I can boot into the ROM / RecoveryMod as long as I have the charger plugged in the tablet.
For Ubuntu, when I use the command $ tail -f /var/log/syslog and plug in my tablet, it shows this log http://pastebin.com/pBpBUA2Q (it identifies the tablet) [note, the tablet is booted into the ROM]
Also, if I'm in the recovery mode and I plug in the tablet, it would enumerate the USB... ~,~
Bump
bump
spilot said:
bump
Click to expand...
Click to collapse
Please don't bump your thread more than once in 24 hours, it's against the rules
Sent from my Galaxy Nexus using Tapatalk HD
bump
Hello,
I know it has been long since this thread stopped.
I'm currently in his shoes and for the life of me cannot find anything on the web to help me solve my problem.
My MSI Enjoy 10" Plus was flashed with the wrong MSI Enjoy 10" update. Now the tablet only turns on when in "Recovery Mode", but selecting in that mode is not possible using 10" Plus' buttons. Is there anyone from you good people that can help? Please? Thanks.
Uhm...bump?
Bump? Need help from the experts here. Please. I'm desperate.
Thank you very much in advance.
Hi to all, my Huawei Ascend G700 that I just bought has gone into a bootloop. I have succesfully root the phone using Huwaei eroot software from as in the picture below but I havent flashed any custom ROM yet.
But then I want to install CWM recovery into the phone as it much feature rich that the stock e3 recovery. So I've downloaded the CWM recovery from the page in the picture below.
I used MobileUncle Tools to boot the CWM recovery & that's when the issue occured. It keep restarting after the Huawei logo. I cant even get into the recovery (by holding volume button up + power button). If I hold the volume down button + power button, a sentence " => FSATBOOT mode... " at the lower left corner of the screen will appear but the phone will reboot itself again & again. Please help. Thank you.
shortcopperjumper said:
Hi to all, my Huawei Ascend G700 that I just bought has gone into a bootloop. I have succesfully root the phone using Huwaei eroot software from as in the picture below but I havent flashed any custom ROM yet.
But then I want to install CWM recovery into the phone as it much feature rich that the stock e3 recovery. So I've downloaded the CWM recovery from the page in the picture below.
I used MobileUncle Tools to boot the CWM recovery & that's when the issue occured. It keep restarting after the Huawei logo. I cant even get into the recovery (by holding volume button up + power button). If I hold the volume down button + power button, a sentence " => FSATBOOT mode... " at the lower left corner of the screen will appear but the phone will reboot itself again & again. Please help. Thank you.
Click to expand...
Click to collapse
I have the exact same problem for me too :crying:
maialo said:
I have the exact same problem for me too :crying:
Click to expand...
Click to collapse
same here.
desperately trying to find a solution, but I guess it's totally bricked ...
the ddsetNa
I'm getting out of options here:
when I try to 'catch' the phone in fastboot mode using a firmare restore tool, the tool detects the phone but complains the connection is broken.
how do I turn off this watchguard that reboots the phone??
jpsollie said:
I'm getting out of options here:
when I try to 'catch' the phone in fastboot mode using a firmare restore tool, the tool detects the phone but complains the connection is broken.
how do I turn off this watchguard that reboots the phone??
Click to expand...
Click to collapse
in case the 2 people here are still looking 4 the answer:
http://forum.xda-developers.com/showthread.php?t=2412017
get the firmware for your phone (don't know if it's G700-U00 or U10), and flash images back. take out the battery, put the software in download mode for the necessary images (=download to phone), and insert the cable while you 're pushing both volume buttons
Huawei Ascend G700 bootloop
Did n`t work for me. Does someone know serial connecting points for Ascend G700, or has .pdf or picture of electrical schematic?
I think , it may help much!
Thanks for answer anyway.
SAme problem Guys plz help and reply any solution
Hi to all, my Huawei Ascend G700 that I just bought has gone into a bootloop. I have succesfully root the phone using Huwaei eroot software from as in the picture below but I havent flashed any custom ROM yet.
But then I want to install CWM recovery into the phone as it much feature rich that the stock e3 recovery. So I've downloaded the CWM recovery from the page in the picture below.
I used MobileUncle Tools to boot the CWM recovery & that's when the issue occured. It keep restarting after the Huawei logo. I cant even get into the recovery (by holding volume button up + power button). If I hold the volume down button + power button, a sentence " => FSATBOOT mode... " at the lower left corner of the screen will appear but the phone will reboot itself again & again. Please help. Thank you.[/QUOTE]
went through same met with same
I have the same problem and tried many different solution but not working ((((((PLEASE HELP!!!
QUOTE=ashish18mohan;48673012]Hi to all, my Huawei Ascend G700 that I just bought has gone into a bootloop. I have succesfully root the phone using Huwaei eroot software from as in the picture below but I havent flashed any custom ROM yet.
But then I want to install CWM recovery into the phone as it much feature rich that the stock e3 recovery. So I've downloaded the CWM recovery from the page in the picture below.
I used MobileUncle Tools to boot the CWM recovery & that's when the issue occured. It keep restarting after the Huawei logo. I cant even get into the recovery (by holding volume button up + power button). If I hold the volume down button + power button, a sentence " => FSATBOOT mode... " at the lower left corner of the screen will appear but the phone will reboot itself again & again. Please help. Thank you.[/QUOTE]
went through same met with same[/QUOTE]
okra9 said:
I have the same problem and tried many different solution but not working ((((((PLEASE HELP!!!
QUOTE=ashish18mohan;48673012]Hi to all, my Huawei Ascend G700 that I just bought has gone into a bootloop. I have succesfully root the phone using Huwaei eroot software from as in the picture below but I havent flashed any custom ROM yet.
But then I want to install CWM recovery into the phone as it much feature rich that the stock e3 recovery. So I've downloaded the CWM recovery from the page in the picture below.
I used MobileUncle Tools to boot the CWM recovery & that's when the issue occured. It keep restarting after the Huawei logo. I cant even get into the recovery (by holding volume button up + power button). If I hold the volume down button + power button, a sentence " => FSATBOOT mode... " at the lower left corner of the screen will appear but the phone will reboot itself again & again. Please help. Thank you.
Click to expand...
Click to collapse
went through same met with same[/QUOTE][/QUOTE]
as I said, use the solution I posted ... I managed to recover my phone with bricked recovery, uboot & boot partition:
- download the original stuff on the page,
- install the program
- tell it to upload firmware parts 'boot' & 'recovery' & start it
- connect the USB cable, hold both volume buttons and then enter the battery. this may not be easy: windows will first need to install a CDC driver, so the first time you try to download it will certainly fail, but maybe the 2nd or 3rd time . You know you're in the good mode when your screen keeps blank.
Sir
I guess I need more assistance from you if you don't mind.I have added my comments in red letters to your email below and if you can assist me on that it will be appreciated
Regards
jpsollie said:
went through same met with same
Click to expand...
Click to collapse
[/QUOTE]
as I said, use the solution I posted ... I managed to recover my phone with bricked recovery, uboot & boot partition:
- download the original stuff on the page,(Which stuff are you talking please give me link about it )
- install the program Which program is this please link about it
- tell it to upload firmware parts 'boot' & 'recovery' & start it
- connect the USB cable, hold both volume buttons and then enter the battery. this may not be easy: windows will first need to install a CDC driver, so the first time you try to download it will certainly fail, but maybe the 2nd or 3rd time . You know you're in the good mode when your screen keeps blank.[/QUOTE]
okra9 said:
Sir
I guess I need more assistance from you if you don't mind.I have added my comments in red letters to your email below and if you can assist me on that it will be appreciated
Regards
Click to expand...
Click to collapse
as I said, use the solution I posted ... I managed to recover my phone with bricked recovery, uboot & boot partition:
- download the original stuff on the page,(Which stuff are you talking please give me link about it )
- install the program Which program is this please link about it
- tell it to upload firmware parts 'boot' & 'recovery' & start it
- connect the USB cable, hold both volume buttons and then enter the battery. this may not be easy: windows will first need to install a CDC driver, so the first time you try to download it will certainly fail, but maybe the 2nd or 3rd time . You know you're in the good mode when your screen keeps blank.[/QUOTE][/QUOTE]
I think the program he is refering to is listed on that other thread that he refers to http://forum.xda-developers.com/showthread.php?t=2412017
The program hisuite is mentioned. just google hisuite and you will find the official Huawei website with the program download.
But a "dummies how to guide" could be useful if anyone that have done this themself could take the trouble to make one.
Personally I just have ordered and not received my G700 yet, and found this thread because I was planning to root and put CWM into it when I get it.
But reading this thread makes me a bit worried if its worth the trouble, as it sounds as its a common problem on these phones.
From what I read, rooting is rather safe, but the CWM part may brick the phone, is this correct?
Stuck at boot loop
jpsollie said:
went through same met with same
Click to expand...
Click to collapse
[/QUOTE]
as I said, use the solution I posted ... I managed to recover my phone with bricked recovery, uboot & boot partition:
- download the original stuff on the page,
- install the program
- tell it to upload firmware parts 'boot' & 'recovery' & start it
- connect the USB cable, hold both volume buttons and then enter the battery. this may not be easy: windows will first need to install a CDC driver, so the first time you try to download it will certainly fail, but maybe the 2nd or 3rd time . You know you're in the good mode when your screen keeps blank.[/QUOTE]
->i used sp flash tool but the software is not detecting my phone even after installing MT65XX VCOM driver
->again the device show up only for couple seconds in fastboot mode like just detected and den removed.
-> tried pressing vol+ key battery removed and den pushing battery but nthng helped.
tried everything but m nt able to read the partition of my device. Plz suggest any alternative to push and replace recovery
Thanks
Cwm g700-u20 v100r001c00b110
Does anyone know how to install CWM recovery to this phone ? I have root this but mobileuncle doesnt install recovery, its just give me a bootloop.
I have tried this many times and many ways, just cant install custom recovery. Can someone help me with this problem ?
I too have the same problem
pihlaja81 said:
Does anyone know how to install CWM recovery to this phone ? I have root this but mobileuncle doesnt install recovery, its just give me a bootloop.
I have tried this many times and many ways, just cant install custom recovery. Can someone help me with this problem ?
Click to expand...
Click to collapse
Any solution yet ??:cyclops:
acacio23 said:
Any solution yet ??:cyclops:
Click to expand...
Click to collapse
nothing yet.
any solution i have the same problem
okra9 said:
Sir
I guess I need more assistance from you if you don't mind.I have added my comments in red letters to your email below and if you can assist me on that it will be appreciated
Regards
Click to expand...
Click to collapse
as I said, use the solution I posted ... I managed to recover my phone with bricked recovery, uboot & boot partition:
- download the original stuff on the page,(Which stuff are you talking please give me link about it )
- install the program Which program is this please link about it
- tell it to upload firmware parts 'boot' & 'recovery' & start it
- connect the USB cable, hold both volume buttons and then enter the battery. this may not be easy: windows will first need to install a CDC driver, so the first time you try to download it will certainly fail, but maybe the 2nd or 3rd time . You know you're in the good mode when your screen keeps blank.[/QUOTE][/QUOTE]
---------- Post added at 02:15 PM ---------- Previous post was at 01:47 PM ----------
pihlaja81 said:
Does anyone know how to install CWM recovery to this phone ? I have root this but mobileuncle doesnt install recovery, its just give me a bootloop.
I have tried this many times and many ways, just cant install custom recovery. Can someone help me with this problem ?
Click to expand...
Click to collapse
Hi how did you get out of the boot loop i have the same issue
Boot Loop
HI i have the same problem of HUAWEI G 700- 10 boot loop while installing CWM recovery using mobileuncle
any solution please
acacio23 said:
HI i have the same problem of HUAWEI G 700- 10 boot loop while installing CWM recovery using mobileuncle
any solution please
Click to expand...
Click to collapse
Read this thread, someone else managed to fix their phone with bootloop
http://forum.xda-developers.com/showthread.php?t=2412017&page=9
shortcopperjumper said:
Hi to all, my Huawei Ascend G700 that I just bought has gone into a bootloop. I have succesfully root the phone using Huwaei eroot software from as in the picture below but I havent flashed any custom ROM yet.
But then I want to install CWM recovery into the phone as it much feature rich that the stock e3 recovery. So I've downloaded the CWM recovery from the page in the picture below.
I used MobileUncle Tools to boot the CWM recovery & that's when the issue occured. It keep restarting after the Huawei logo. I cant even get into the recovery (by holding volume button up + power button). If I hold the volume down button + power button, a sentence " => FSATBOOT mode... " at the lower left corner of the screen will appear but the phone will reboot itself again & again. Please help. Thank you.
Click to expand...
Click to collapse
do u got the solution?
Mobile uncle tools problem
okra9 said:
I have the same problem and tried many different solution but not working ((((((PLEASE HELP!!!
QUOTE=ashish18mohan;48673012]Hi to all, my Huawei Ascend G700 that I just bought has gone into a bootloop. I have succesfully root the phone using Huwaei eroot software from as in the picture below but I havent flashed any custom ROM yet.
But then I want to install CWM recovery into the phone as it much feature rich that the stock e3 recovery. So I've downloaded the CWM recovery from the page in the picture below.
I used MobileUncle Tools to boot the CWM recovery & that's when the issue occured. It keep restarting after the Huawei logo. I cant even get into the recovery (by holding volume button up + power button). If I hold the volume down button + power button, a sentence " => FSATBOOT mode... " at the lower left corner of the screen will appear but the phone will reboot itself again & again. Please help. Thank you.
Click to expand...
Click to collapse
went through same met with same[/QUOTE][/QUOTE]
Hi i faced the same issue , the reason is mobile uncle told dint download the recovery image properly it was of 0 KB and i flashed it and error ..
still awating proper document to recover using sp tool recovery
Hello! I don't know where i should post this since the UMI X3 device isn't on this site, so i just post it here...
I installed a custom rom, now it's bootlooping.
If i turn it on it will show the little boot splash screen, then the screen will go black and usually it would show the boot loading screen but it doesn't, it reboots again to the boot splash screen.
I tried searching on google, but none of the forum posts actually helped me.
I try to holds down the power button and the volume up button at the same time, but it will just do the same bootloop thing.
The home button is a touch button, and i actually already tried holding down on that but it didn't work.
I also tried holding power button and volume down, and i tried holding all the buttons down at once (power + volume up and down)... also no succes.
Now it used to work, i got into some chinese bootloader before i installed this rom.
So, basicly it won't get into any recovery. I did install clockworkmod recovery actually and it did work, yet i needed to launch it via mobile uncle tools to get into it. I think im totally ****ed now...
Pleace, is there ANY way to solve this problem?
Problem in a nutshell:
Boot looping splash screen, can't get into recovery mode. (PS: i also tried to connect it via USB but it won't find my phone...)
- Kyran
UPDATE:
I'm now able to get into recovery mode!
However i can't mount usb.
Same problem
Kyranio said:
I'm now able to get into recovery mode!
However i can't mount usb.
Click to expand...
Click to collapse
Hi Kyriano,
I have the same problem after installing the cynogenmod, does your phone work now. How did you get in the recovery mode??
posible solution
Hi,
After struggling with this issue all day i found a quite simple solution.
The cause of the bootloop in my case was the simcard. So this is what i did:
1. remove simcard tray
2. Turn the phone off and on
3. If everything is ok the bootloop stopped, if not try to reboot again
4. Download mobileuncle in the playstore
5. Open the app click on; into recovery mode
6. Recovery will open and then hopefully you made a backup.Restore it and voila!
If you did not make a back try to flash the official umi ROM.
I hope this solved your problem to.
Greets ryan
Hi, I've acquired a NABI 2 to try and repair off a friend but its proving difficult to say the least. I know he was doing something with the firmware but beyond that im not sure.
The current state its in is this: It doesnt power on by pressing the power button. If you enter the recovery menu (VOL +, VOL- and power) the recovery menu displays in the top left with the nabi logo in the centre of the screen. The menu cannot be navigated, either its froze or its unresponsive. If i connect it by usb when in the recovery menu the PC detects it as a MTP USB Device but it fails to install the drivers.
Really i just want this back to factory standard, is their anyway to put this back in working order? I've not a whole lot of android experience so please, treat me as a noob with step by step instructions.
Any help appreciated
Update
As is often the case new things happened after i posted, i can now access the recovery menu. This happened when i tried to instal the stock 2.0.5 from SD card
Rubberduckuy said:
As is often the case new things happened after i posted, i can now access the recovery menu. This happened when i tried to instal the stock 2.0.5 from SD card
Click to expand...
Click to collapse
I'm short on time this Christmas Eve but the general idea is this if it's a US Nabi2: http://forum.xda-developers.com/showpost.php?p=51037177&postcount=21
EXCEPT use the files from here, http://forum.xda-developers.com/showpost.php?p=54871957&postcount=2342
instead of the ones it says to download in the first post I link, use the files from the second post I linked(Nabi 246 files, JB bootloader). It will work but the only trick is which TWRP to start with ICS ot JB. You may have to try one and then the other. After that the procedure should get everything running again.
Ok, i managed to get TWRP working again but its unable to install anything, whenever i try it just shows as in the screenshot. Any further advice?
Rubberduckuy said:
Ok, i managed to get TWRP working again but its unable to install anything, whenever i try it just shows as in the screenshot. Any further advice?
Click to expand...
Click to collapse
It's the wrong TWRP, if you used ICS TWRP use JB or vice versa.
no power on or boot
aicjofs said:
It's the wrong TWRP, if you used ICS TWRP use JB or vice versa.
Click to expand...
Click to collapse
i have no power and no boot after flashing bootloader with JB246bootloader after I flashed 246 stock .. nabi 2