Hi, i was try to update my N7000 to 4.1.2 , when i was use Odin to PC, it stuck on as below , i was left it in more than 30mins.
<OSM> Please wait..
<OSM> N7000DXLSE_N7000OLBLSE_N7000DXLS8_HOME.TAR.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
<ID:0/016> Initialzation..
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> zImage
<ID:0/016> NAND Write Start!!
and i also turn off my phone & start again to recovery mode , it can not turn it , it just stuck on start page ( GT- N7000 ).
what can i do ps help.
TQ
Wrong forum, this is I9100 Q&A. I've asked mods to move your thread here, wait until they do/someone replies.
Related
I made the mistake of attempting to apply the US region stock ROM to my apparent Europe version (KJ4) galaxy note.
In so doing, it now won't seem to turn on.
However, I can hear it connect and disconnect from the computer if I toggle the power button. I'm assuming it's continuously in the download mode until I get it out? I don't know, since nothing shows up on the screen. Am I screwed? Should I attempt a replacement?
Please help me.. if I posted in the wrong forum, please move the post.
I will give you my first born if you can help me, no strings attached.
<ID:0/012> Added!!
<ID:0/012> Removed!!
<ID:0/012> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P7310XEUKJ4_P7310XXKJ4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Set PIT file..
<ID:0/012> DO NOT TURN OFF TARGET!!
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> boot.img.md5
<ID:0/012> NAND Write Start!!
<ID:0/012>
<ID:0/012> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I've made sure no KIES things were running on my PC.
I've tried different USB ports.
I've unzipped Odin3 again.
Worst part is that I changed my SIM over from my iPhone4 already, so I have no phone.. no ladies now... nothing. I'm turning into a monk.
Tried to flash firm:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXKKA_N7000XEUKK3_N7000XXKK5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Get PIT for mapping..
<ID:0/011> Firmware update start..
<ID:0/011> zImage
<ID:0/011> NAND Write Start!!
<ID:0/011> boot.bin
<ID:0/011> modem.bin
...and again.. sits at "modem.bin"
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXKKA_N7000XEUKK3_N7000XXKK5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Set PIT file..
<ID:0/011> DO NOT TURN OFF TARGET!!
<ID:0/011> Get PIT for mapping..
<ID:0/011> Firmware update start..
<ID:0/011> zImage
<ID:0/011> NAND Write Start!!
<ID:0/011> boot.bin
<ID:0/011> modem.bin
Assuming you cant get into CWM or anything?
CdTDroiD said:
Assuming you cant get into CWM or anything?
Click to expand...
Click to collapse
That's correct sir.
But I can hear it connecting/reconnecting if I toggle it.
Is this a complete irreversible hard brick?
I don't think so...
I don't think so.... try to flash with heimdall!!!
or
Send to samsung.... a month ago i sent my GT-P1000 (galaxy tab) completely bricked (it doesn't power on!!!!!) in 2 weeks they have sent me a new one!!
Just Try !!!!
Cheers Cascio97
Mushinronjya said:
I made the mistake of attempting to apply the US region stock ROM to my apparent Europe version (KJ4) galaxy note.
In so doing, it now won't seem to turn on.
However, I can hear it connect and disconnect from the computer if I toggle the power button. I'm assuming it's continuously in the download mode until I get it out? I don't know, since nothing shows up on the screen. Am I screwed? Should I attempt a replacement?
Please help me.. if I posted in the wrong forum, please move the post.
I will give you my first born if you can help me, no strings attached.
<ID:0/012> Added!!
<ID:0/012> Removed!!
<ID:0/012> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P7310XEUKJ4_P7310XXKJ4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Set PIT file..
<ID:0/012> DO NOT TURN OFF TARGET!!
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> boot.img.md5
<ID:0/012> NAND Write Start!!
<ID:0/012>
<ID:0/012> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I've made sure no KIES things were running on my PC.
I've tried different USB ports.
I've unzipped Odin3 again.
Worst part is that I changed my SIM over from my iPhone4 already, so I have no phone.. no ladies now... nothing. I'm turning into a monk.
Tried to flash firm:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXKKA_N7000XEUKK3_N7000XXKK5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Get PIT for mapping..
<ID:0/011> Firmware update start..
<ID:0/011> zImage
<ID:0/011> NAND Write Start!!
<ID:0/011> boot.bin
<ID:0/011> modem.bin
...and again.. sits at "modem.bin"
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXKKA_N7000XEUKK3_N7000XXKK5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Set PIT file..
<ID:0/011> DO NOT TURN OFF TARGET!!
<ID:0/011> Get PIT for mapping..
<ID:0/011> Firmware update start..
<ID:0/011> zImage
<ID:0/011> NAND Write Start!!
<ID:0/011> boot.bin
<ID:0/011> modem.bin
Click to expand...
Click to collapse
hard bricked, you have to use riffbox
hi
I probably tried loading i9100 rom into my i9100G phone and now its stuck.
I got BSOD (Black Screen Of Death) - see attached jpg.
when i connected the phone back to the pc the odin app recognized it (i guess it remained in download mode).
I loaded the following file GT-I9100G_ICS_ClockworkMod-Recovery_6.0.1.2.tar and by that i coud enter download mode and recovery mode.
I tried to load ROM stock and failed time and again, each time got the same message:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100GXXLPQ_I9100GODDLP7_I9100GDDLP5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> cache.img
<ID:0/007> NAND Write Start!!
<ID:0/007> factoryfs.img
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
CAN SOMEONE PLEASE HELP ME TO REVIVE MY PHONE?
Thanks.
itsik888 said:
hi
I probably tried loading i9100 rom into my i9100G phone and now its stuck.
I got BSOD (Black Screen Of Death) - see attached jpg.
when i connected the phone back to the pc the odin app recognized it (i guess it remained in download mode).
I loaded the following file GT-I9100G_ICS_ClockworkMod-Recovery_6.0.1.2.tar and by that i coud enter download mode and recovery mode.
I tried to load ROM stock and failed time and again, each time got the same message:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100GXXLPQ_I9100GODDLP7_I9100GDDLP5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> cache.img
<ID:0/007> NAND Write Start!!
<ID:0/007> factoryfs.img
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
CAN SOMEONE PLEASE HELP ME TO REVIVE MY PHONE?
Thanks.
Click to expand...
Click to collapse
hi, did you resolve your problem with your phone? i have the same problem, but with a Galaxy Note. if you done it, can you give me a hand? thanks
adyolcian said:
hi, did you resolve your problem with your phone? i have the same problem, but with a Galaxy Note. if you done it, can you give me a hand? thanks
Click to expand...
Click to collapse
Go to Galaxy Note forum.
Sent from my GT-I9100
boki9999 said:
Go to Galaxy Note forum.
Sent from my GT-I9100
Click to expand...
Click to collapse
And the other guy can go to the Gt-I9100GGGGGGGGGG forum.
I had the same problem and I've flashed a stock ICS rom via odin. And do a factory reset/ cache wipe. After that *2767*3855#. It's a hard reset and you'll lose everything but you can use your phone again
Edi got the same problem. Already tried flash stock 4.0.1 rom. FAILED.
<OSM> Leave CS..
<ID:0/028> Odin v.3 engine (ID:28)..
<ID:0/028> File analysis..
<ID:0/028> SetupConnection..
<ID:0/028> Initialzation..
<ID:0/028> Get PIT for mapping..
<ID:0/028> Firmware update start..
<ID:0/028> boot.bin
<ID:0/028> NAND Write Start!!
<ID:0/028>
<ID:0/028> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
What should i do now ?
shinseijuro said:
Edi got the same problem. Already tried flash stock 4.0.1 rom. FAILED.
<OSM> Leave CS..
<ID:0/028> Odin v.3 engine (ID:28)..
<ID:0/028> File analysis..
<ID:0/028> SetupConnection..
<ID:0/028> Initialzation..
<ID:0/028> Get PIT for mapping..
<ID:0/028> Firmware update start..
<ID:0/028> boot.bin
<ID:0/028> NAND Write Start!!
<ID:0/028>
<ID:0/028> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
What should i do now ?
Click to expand...
Click to collapse
try to change the port USB, or try it on another PC if you can
if anyone know, is there any way to change the firmware beside ODIN? thanks
shinseijuro said:
Edi got the same problem. Already tried flash stock 4.0.1 rom. FAILED.
<OSM> Leave CS..
<ID:0/028> Odin v.3 engine (ID:28)..
<ID:0/028> File analysis..
<ID:0/028> SetupConnection..
<ID:0/028> Initialzation..
<ID:0/028> Get PIT for mapping..
<ID:0/028> Firmware update start..
<ID:0/028> boot.bin
<ID:0/028> NAND Write Start!!
<ID:0/028>
<ID:0/028> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
What should i do now ?
Click to expand...
Click to collapse
This actually happens quite often for me. Just try again and again. You'll get there eventually. Try and do the process as quick possible. That helped me.
Not working. Now my friend cant use his phone and its not even rooted yet! All he wants just a standard pc kies update and kies give him the computer screen.
Now using:
Sony Xperia tipo ST21i
stock 4.0.4
11.0.A.4.22
(rooted, locked bootloader)
Current problem:
Cant get past installing flash drivers in xp.
Hi all
please understand me and help ?
i have a bricked Fascinate because i flashed wrong Odin package and it dead
so that I do JTag for it to restore downloadmode,
yes it is restored to downloadmode but when i try to flash any modem or any odin rom it arrive to modem and said fail
the txt message for Odin
<ID:0/017> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> powerwashed_20_b3_Full_ec09modem.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/017> Odin v.3 engine (ID:17)..
<ID:0/017> File analysis..
<ID:0/017> SetupConnection..
<ID:0/017> Initialzation..
<ID:0/017> Set PIT file..
<ID:0/017> DO NOT TURN OFF TARGET!!
<ID:0/017> Get PIT for mapping..
<ID:0/017> Firmware update start..
<ID:0/017> boot.bin
<ID:0/017> NAND Write Start!!
<ID:0/017> cache.rfs
<ID:0/017> dbdata.rfs
<ID:0/017> factoryfs.rfs
<ID:0/017> modem.bin
<ID:0/017>
<ID:0/017> Complete(Write) operation failed.
<ID:0/017> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
note : red Color for explain
the pict can explain
sorry for bad english
thaifani said:
Hi all
please understand me and help ?
i have a bricked Fascinate because i flashed wrong Odin package and it dead
so that I do JTag for it to restore downloadmode,
yes it is restored to downloadmode but when i try to flash any modem or any odin rom it arrive to modem and said fail
the txt message for Odin
<ID:0/017> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> powerwashed_20_b3_Full_ec09modem.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/017> Odin v.3 engine (ID:17)..
<ID:0/017> File analysis..
<ID:0/017> SetupConnection..
<ID:0/017> Initialzation..
<ID:0/017> Set PIT file..
<ID:0/017> DO NOT TURN OFF TARGET!!
<ID:0/017> Get PIT for mapping..
<ID:0/017> Firmware update start..
<ID:0/017> boot.bin
<ID:0/017> NAND Write Start!!
<ID:0/017> cache.rfs
<ID:0/017> dbdata.rfs
<ID:0/017> factoryfs.rfs
<ID:0/017> modem.bin
<ID:0/017>
<ID:0/017> Complete(Write) operation failed.
<ID:0/017> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
note : red Color for explain
the pict can explain
sorry for bad english
Click to expand...
Click to collapse
If you flashed with the wrong package
I would Highly recommend flashing with the Verizon OTA Full package -- eh03_full_odin.tar.md5
make sure you have the atlas_v2.2.pit
if that doesn't work for some reason please try with the Odin3 v1.83 instead of the 3.04 version
.
thanks i will try
hhp_211 said:
If you flashed with the wrong package
I would Highly recommend flashing with the Verizon OTA Full package -- eh03_full_odin.tar.md5
make sure you have the atlas_v2.2.pit
if that doesn't work for some reason please try with the Odin3 v1.83 instead of the 3.04 version
.
Click to expand...
Click to collapse
i will try and tell you what the result
not solved and same error
hhp_211 said:
If you flashed with the wrong package
I would Highly recommend flashing with the Verizon OTA Full package -- eh03_full_odin.tar.md5
make sure you have the atlas_v2.2.pit
if that doesn't work for some reason please try with the Odin3 v1.83 instead of the 3.04 version
.
Click to expand...
Click to collapse
Please help me , I get this error
ID:0/346> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> eh03_full_odin.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/346> Odin v.3 engine (ID:346)..
<ID:0/346> File analysis..
<ID:0/346> SetupConnection..
<ID:0/346> Initialzation..
<ID:0/346> Set PIT file..
<ID:0/346> DO NOT TURN OFF TARGET!!
<ID:0/346> Get PIT for mapping..
<ID:0/346> Firmware update start..
<ID:0/346> factoryfs.rfs
<ID:0/346> recovery.bin
<ID:0/346> zImage
<ID:0/346> boot.bin
<ID:0/346> cache.rfs
<ID:0/346> dbdata.rfs
<ID:0/346> modem.bin
<ID:0/346>
<ID:0/346> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
@thaifani
Try this::
Keep Odin open and change USB ports, remount the PDA & flash.
You may need to do this 3 - 4 tries before it works completely
.
not worked
any help please
hi, thaifani ...... I have got the same problem. I can only enter the Download mode ... if try to flash anything .... NAND WRITE Failed. Don't know what to do. My warranty expired 2months ago. I was running on KitKat 4.4.2 rooted for 3 months without any problems.
Hello XDA,
I did brick my phone by trying to downgrade to 5.0.2 from 5.1.1 and bricked my phone and searching this forum I felt that there should be a post like this to ease the journey of people like me. As I did learn a lot from my 5 years android journey, I would like help everybody like me. Therefore if I find any important/"you may not know" fixes, I will share here with headings. Also If you have another solutions for any problems of these kind; please write here so I can collect em' all in the OP. Let's go!
-ODIN fail while flashing hidden.img-
Solution: This is caused because of your partition(pit). In XDA, you can find .pit files of S6 Edge for several models (i.e. I have a g925f so i have to find the corresponding pit file. The one worked for me was the G925F pit with Hidden_300M. First you flash this pit to your phone, then try to flash your rom; you're good to go!
Solution 2 Thanks to @Alex-V : Just delete the hidden.img from the rom.
---------------------------------------------------------------
-If you can't properly enter to recovery mode-
Solution: Please do the combo "Volume Down-Home-Power" until you reach download mode. When you reach there again do the same combo until the screen goes off. When it goes off QUICKLY switch to "Volume Up-Home-Power" combo and hold it until the screen comes in and dims a bit. When it dims release all buttons and ta-da you're in recovery mode.
---------------------------------------------------------------
-ODIN gives a fail at NAND write-
Solution: This problem is caused because of the nand mismatches (generally, or build differences etc.). Doing this may cause a hard-brick IF YOU DON'T follow the instructions CAREFULLY.
1) Get your device to download mode by using this combo "VolumeDown-Home-Power"
2) Open an UP TO DATE ODIN.
3) Find the corresponding .PIT file for your S6 EDGE.
4) Find the corresponding stock rom for your S6 EDGE.
5) Then put them into odin CORRECTLY. Rom to "AP", .pit to PIT
6) Make Sure these are checked: "Re-partition","NAND all erase"
7) Plug your device in and then press start.
After these you should be already flashed correctly without any nand write fail.
---------------------------------------------------------------
-SW REV CHECK FAIL DEVICE: 2 BINARY:1-
This happens when you try to downgrade from 5.1.1... Thanks to Samsung, we can not downgrade to repair our phones or save them because of the locked bootloader. So you have to flash to 5.1.1 again.
If anyone with a working rooted phone, can he/she share his/her own nand backup, so people with screwed boots can recover
or simple delete the hidden.img
Added to the post, thanks mate. Also looking for how to fix corrupted sdcard (theres no mmcblk0x file)
Hi,
I'm following your advice to try and overcome my S6 Edge's issue with failing to NAND write but I am still getting the same NAND write fail. I have another post detailing the issue here http://forum.xda-developers.com/showpost.php?p=67930722&postcount=5 if you want more info but I'll just post the Odin log here too just in case you can spot where I went wrong.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925W8VLU1AOCG_G925W8OYA1AOCG_G925W8VLU1AOCG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Added!!
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Erase...
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My device is an S6 Edge G925W8. Thanks.
Please Respond
Malganor said:
Hi,
I'm following your advice to try and overcome my S6 Edge's issue with failing to NAND write but I am still getting the same NAND write fail. I have another post detailing the issue here http://forum.xda-developers.com/showpost.php?p=67930722&postcount=5 if you want more info but I'll just post the Odin log here too just in case you can spot where I went wrong.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925W8VLU1AOCG_G925W8OYA1AOCG_G925W8VLU1AOCG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Added!!
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Erase...
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My device is an S6 Edge G925W8. Thanks.
Click to expand...
Click to collapse
I am also getting the exact same thing. I Put in the pit file like instructed as well as the correct rom... still get the same NAND WRITE START.
Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925W8VLU1AOCG_G925W8OYA1AOCG_G925W8VLU1AOCG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Erase...
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I'm having trouble with flashing the stock rom for the Samsung Galaxy S3 on Odin, as I get a fail everytime I try to flash the rom onto my device.
This comes up everytime I try to flash:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGOK1_I9300NZCGOK1_I9300XXUGOK1_HOME.tar.md 5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
The model number is a GT-i9300, and no stock roms so far have succeeded.
I have used Odin 3.07 and Odin 3.09, my samsung drivers are up to date and Odin still fails to flash the rom.
I've also tried different usb cables, along with trying out different ports, none of them have worked.
On the S3 it's currently running TWRP version 3.0.2-1, it also asks me whether or not I keep it "System Read only" whenever I go in recovery mode. And each time I always choose the option of keeping it read only. I don't know if these has anything to do with Odin failing to flash the rom but might as well mention it. I was also running CyanogenMod13 for roughly a month before the brick happened.
Any help would be appreciated !
Reply
Kiddzu said:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGOK1_I9300NZCGOK1_I9300XXUGOK1_HOME.tar.md 5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
Click to expand...
Click to collapse
Hi, after NAND Write Start!! and this double !! means it start to WRITE on your Device Flash Memory when this fails it means that the cable dont transfer correct data / Cable Connection OK but wrong cable cannot write correctly on your device
I recommend you to use Original cable when flashing or a other cable but look for the compatibility to devices:good:
as far as I know it cant be a other opportunity to fix this because in the Download Mode of the s3 is the only way to Flash Original Firmware when this fails i dont now how to continue and i cannot help you more than that
And sry for my bad as fu** English