Here is the MJ4 firmware in a flashable tar. It includes bootloader, modem, baseband, etc.
This will NOT wipe your phone or data. It does not flash a ROM, only the firmware. This will update people to the MJ4 baseband.
hlte SPR Firmwares
Thank You Sir...
freeza said:
Here is the MJ4 firmware in a flashable tar. It includes bootloader, modem, baseband, etc.
This will NOT wipe your phone or data. It does not flash a ROM, only the firmware. This will update people to the MJ4 baseband.
hlte SPR Firmwares
Click to expand...
Click to collapse
Thank you, sir! Just terrific providing this.
micmars said:
Thank you, sir! Just terrific providing this.
Click to expand...
Click to collapse
Much appreciated... Just to confirm though because I'm not logged into androidfilehost;
Is this the mj4firmware.tar you uploaded about a half hour ago?
https://www.androidfilehost.com/?fid=23212708291676766
54.6MB
MD5: 269930fed0e2672940d3b2634a9e37bc
Kompster said:
Much appreciated... Just to confirm though because I'm not logged into androidfilehost;
Is this the mj4firmware.tar you uploaded about a half hour ago?
https://www.androidfilehost.com/?fid=23212708291676766
54.6MB
MD5: 269930fed0e2672940d3b2634a9e37bc
Click to expand...
Click to collapse
Yes
freeza said:
Here is the MJ4 firmware in a flashable tar. It includes bootloader, modem, baseband, etc.
This will NOT wipe your phone or data. It does not flash a ROM, only the firmware. This will update people to the MJ4 baseband.
hlte SPR Firmwares
Click to expand...
Click to collapse
Can you flash this from phone? My computer is broke right now...
xyojimbox said:
Can you flash this from phone? My computer is broke right now...
Click to expand...
Click to collapse
I'm sure you can flash it with Mobile Odin, but it's not a recovery flashable.
Careful with mobile Odin. Last time I tried bit with a modem it didn't work so well. Had to reflash whole tar from desktop to get phone back in working order. Unless they fixed it since then.
Note 3 or Gear Sent
freeza said:
I'm sure you can flash it with Mobile Odin, but it's not a recovery flashable.
Click to expand...
Click to collapse
Says phone is not supported and I don't have external sd . Any plans in future to make this a zip?
xyojimbox said:
Says phone is not supported and I don't have external sd . Any plans in future to make this a zip?
Click to expand...
Click to collapse
Same here with mobile odin. Guess ill just stop being lazy and boot up the pc lol
Sent from my SM-N900P using xda app-developers app
Just to be sure since I havent flashed firmware via odin in a really long time, what slot do we put this in PDA?
BlGPAPA1321 said:
Same here with mobile odin. Guess ill just stop being lazy and boot up the pc lol
Sent from my SM-N900P using xda app-developers app
Click to expand...
Click to collapse
My computer broke so I'm screwed lol
Just flashed and in about phone it still says my baseband is MI3
I believe you need to be on MI5 first. At least that's what I seen a lot from other people before u can go to MJ4. Don't kill me if I'm wrong
Sent from my SM-N900P using xda app-developers app
rbtrucking said:
Just flashed and in about phone it still says my baseband is MI3
Click to expand...
Click to collapse
Did Odin say it was successful?
Confirming that an Odin from MI5 booted right back up into my rom with Software and Baseband MJ4.
Thanks freeza. You're like the Robin Hood of firmware.
freeza said:
Did Odin say it was successful?
Click to expand...
Click to collapse
Yes it did. Maybe I should try it again, perhaps use a regular usb 2.0 cable? For some reason this 3.0 cable doesnt get along to well with my computer. First time rooting it I almost bricked it because it kept failing then I got the firmware upgeade encountered an error message when trying to boot my phone up but luckily finally it worked and all was well.
I am supposed to be putting this in the PDA slot of odin and leaving the file zipped exactly as it was when I downloaded it, correct?
rbtrucking said:
Yes it did. Maybe I should try it again, perhaps use a regular usb 2.0 cable? For some reason this 3.0 cable doesnt get along to well with my computer. First time rooting it I almost bricked it because it kept failing then I got the firmware upgeade encountered an error message when trying to boot my phone up but luckily finally it worked and all was well.
I am supposed to be putting this in the PDA slot of odin and leaving the file zipped exactly as it was when I downloaded it, correct?
Click to expand...
Click to collapse
The stock cable should be adequate if not good quality. Compared to the Epic 4G and cable for that I had before...
Flash .zips. Odin .tars .tar.md5 .pit or whatever it is properly. Make sure you have the correct .tar in the pda slot and use an updated version of Odin3 (3.04) and leave all the default settings as is, aside from the PDA .tar, hit start.
Edit: Also make sure to check the MD5, maybe you got a corrupt download.
Kompster said:
The stock cable should be adequate if not good quality. Compared to the Epic 4G and cable for that I had before...
Flash .zips. Odin .tars .tar.md5 .pit or whatever it is properly. Make sure you have the correct .tar in the pda slot and use an updated version of Odin3 (3.04) and leave all the default settings as is, aside from the PDA .tar, hit start.
Edit: Also make sure to check the MD5, maybe you got a corrupt download.
Click to expand...
Click to collapse
Still didnt work. Do I need to be on MI5 like you suggested earlier for this to work?
I wonder if we can pull the MI5 stock keyboard and replace it with the MJ4 to get the gray colored keyboard back
BrianBaker said:
I wonder if we can pull the MI5 stock keyboard and replace it with the MJ4 to get the gray colored keyboard back
Click to expand...
Click to collapse
Yeah, you can.
Related
Much like I did for ED01, I created a new Odin for the OTA ED03 update. Once again, this doesn't include the modem, just the base system, kernel, and recovery. It will also perform a factory reset, and is currently Odin only, I'll create a CWM flashable package at some point as well. Enjoy. This should be fully stock unrooted as I was only temp-rooted when I created the image.
Download here
Benefits over ED01 as its 2 days newer than ED01 according to build date??
Sent from my SCH-I500 using XDA App
is it rooted? i figure its stock.
am i a noob? yes. but im addicted to flashing so im about to do it!!!
ED03????? WTF over?!?!?!?!
Bubbadogg14 said:
Benefits over ED01 as its 2 days newer than ED01 according to build date??
Sent from my SCH-I500 using XDA App
Click to expand...
Click to collapse
See the ED03 thread in General
touchthecaleb said:
is it rooted? i figure its stock.
Click to expand...
Click to collapse
It is fully stock and should be unrooted as well.
Hashes
Could you provide file hashes? I've had corrupted download with very small errors which was not detected until I use odin.
beray5 said:
Could you provide file hashes? I've had corrupted download with very small errors which was not detected until I use odin.
Click to expand...
Click to collapse
Umm, if it fails verification in Odin, it doesn't flash. How is allowing Odin to check it harder than checking it manually that you wouldn't just allow Odin to work as it is designed to do?
ok I flashed it! I don't know what's different but it's working perfectly.
Im using the latest otb kernel the latest cwm (in purple) and the ec01 radio.
I even rooted it and uninstalled all the annoying aps. Think I'm going to use this rom for now. Thanks imnuts!!!!
Edit: it just feels good to be "up-to-date" lol
Edit: LOL! such small changes.... Pointless but fun.
imnuts said:
Umm, if it fails verification in Odin, it doesn't flash. How is allowing Odin to check it harder than checking it manually that you wouldn't just allow Odin to work as it is designed to do?
Click to expand...
Click to collapse
I'm very often in places with no connection of any kind whatsoever, its also when I'm between time waiting and had the time for things like odin.
If the file is corrupted, then I would have to abort and wait for the next unknown available free time period to repeat all over again.
I don't see any files on the forums to attain the ED03 modem
Odin has a built in MD5, and created the file to support it. If you don't have a connection or time to flash via Odin, how is having the checksum going to help you? No connection and the checksum is bad, you can't download the file again. No time for Odin, and you probably don't have time to generate and verify a checksum because in the time that it'd take you to verify it, you'd be part way through flashing in Odin.
AuroEdge said:
I don't see any files on the forums to attain the ED03 modem
Click to expand...
Click to collapse
That's because there isn't a file available.
If you want the radio, you'll need to Odin back to DL09 or DI01 and go through the OTA process
imnuts said:
Odin has a built in MD5, and created the file to support it. If you don't have a connection or time to flash via Odin, how is having the checksum going to help you? No connection and the checksum is bad, you can't download the file again. No time for Odin, and you probably don't have time to generate and verify a checksum because in the time that it'd take you to verify it, you'd be part way through flashing in Odin.
Click to expand...
Click to collapse
I'll just make do with my own limitations.
Thanks.
Os anyone working on a debinged / debloated version of this?
Sent from my SCH-I500 using Tapatalk
MANY many thanks, imnuts! This will come in VERY handy in the future!
heya mate
first up thanks awesome pice of work indeed.
second , I AM A NEWBIE on myvzn fsc that i am using in INDIA i guess only DL09 seems to working well as all other builds apart from DL09 and EB01 seem to stuck on language selection after first boot.
]can you please tell me what do i have to actually do to install it ( your odin package )
i mean my details are :
Firmare
2.1-update1
baseband version
S:i500.04V.DL09
Kernal version
2,6.29
Build number
SCH-I500.DL09
the handset aint rooted ( as there is no CWM or superuser thingy ion here there is a vooodoo folder in the sdcard though - i am a noob LOL pl bear with me )
please help me man , i am sorta fed up now flashing cstuff 10 times a day since last 4 days
regards
lord dredd said:
heya mate
first up thanks awesome pice of work indeed.
second , I AM A NEWBIE on myvzn fsc that i am using in INDIA i guess only DL09 seems to working well as all other builds apart from DL09 and EB01 seem to stuck on language selection after first boot.
]can you please tell me what do i have to actually do to install it ( your odin package )
i mean my details are :
Firmare
2.1-update1
baseband version
S:i500.04V.DL09
Kernal version
2,6.29
Build number
SCH-I500.DL09
the handset aint rooted ( as there is no CWM or superuser thingy ion here there is a vooodoo folder in the sdcard though - i am a noob LOL pl bear with me )
please help me man , i am sorta fed up now flashing cstuff 10 times a day since last 4 days
regards
Click to expand...
Click to collapse
You should use this -> http://forum.xda-developers.com/showthread.php?t=1044474
Since there will not be any data wipe in that procedure as you already are on DL09 you should be able to update to ED01 without being stuck at the language menu.
Are there actually any benefits
to the ED03 update as opposed to ED01?
beray5 said:
You should use this -> http://forum.xda-developers.com/showthread.php?t=1044474
Since there will not be any data wipe in that procedure as you already are on DL09 you should be able to update to ED01 without being stuck at the language menu.
Click to expand...
Click to collapse
well i did that as well
still i get stuck at language selection window ,
just donno what to do.
seems like apart from dl09 and eb01 no other ROM works
pntballer505 said:
Are there actually any benefits
to the ED03 update as opposed to ED01?
Click to expand...
Click to collapse
benefits: very little if any
negatives? there are no mods/roms/themes available and probably wont be
I recently had to revert back to my verison fascinate and now I need the file to revert it back to stock. I tried all the links on here but the seem to be dead. Does anyone have the files I need for Odin. Also I would like to get a hold of Blackhole ROM again. Thanks
find my guide in general section
http://forum.xda-developers.com/showthread.php?t=1526488
Right here if you still need it. I used the EH03 one.
thanks for your reply
hey I tried the files but I dont think their for verizon, do you have or know where I can get verison I think it was EB01.
sidduced said:
hey I tried the files but I dont think their for verizon, do you have or know where I can get verison I think it was EB01.
Click to expand...
Click to collapse
yes those are verizon files.
not sure whats going on but I followed the steps and odin says hash is invalid. I must be on an older build and it wont let me upgrade for some reason. I even tried it without pit. Any ideas?
sidduced said:
not sure whats going on but I followed the steps and odin says hash is invalid. I must be on an older build and it wont let me upgrade for some reason. I even tried it without pit. Any ideas?
Click to expand...
Click to collapse
Try redownloading the file. It may be a corrupt download.
Sent from my SCH-I500 using xda app-developers app
Hey, guys. I have a question that is kinda similar to this post as well. I accidentally went into my stock recovery and wiped my phone. So by using odin I can restore my phone using the pit file and placing EOH3 under PDA and click start?
tburch82 said:
Hey, guys. I have a question that is kinda similar to this post as well. I accidentally went into my stock recovery and wiped my phone. So by using odin I can restore my phone using the pit file and placing EOH3 under PDA and click start?
Click to expand...
Click to collapse
Yep, don't forget to click re-partition (only do this when you Odin with the .pit file)
Sent from my SCH-I500 using xda premium
Hey guys, here's an Odin flashable of the NH7 modem, for those who wish to remain on their current setup but still benefit from having the new baseband.
The steps to flash this are as follows (make sure you have the Samsung mobile drivers installed so that your phone can be recognized by Odin):
-Disconnect your phone from the PC, if it's connected.
-Completely power down your phone, not reboot, or boot into download mode, but power down.
-Power back on your phone into download mode (vol+down,power,home)
-Open Odin (3.04/3.09) and connect your phone to the PC. At this point, Odin shoudl say <<Added>> or something of the sort.
-Uncheck "auto reboot" from Odin.
-Load up this NH7 baseband tar image into the PDA (3.04) or AP(?) (3.09) section of Odin, and flash.
-Once complete, disconnect your phone, remove the battery for around 5-10 seconds, then power your phone back on into download mode.
-Check "auto reboot" from Odin.
-Flash again, then let your phone auto reboot back into android.
-You should either receive an "android has been upgraded" message or you can verify you're on the new baseband by checking settings>about
-Profit
Note: Steps were taken from the unlock thread in general.
Download NH7 baseband/modem: Here
Thanks for this
Sent from my SM-N900P using Tapatalk
Awesome!
Mobile Odin
Thanks for this Freeza! Can I use this with mobile Odin?? I don't have a windows computer (Zorin (umbuntu)). Thanks again for all of your awesome work sir.
Note: Steps were taken from the unlock thread in general.
Download NH7 baseband/modem: Here[/QUOTE]
I'm trying to flash this through Odin 3.07 and keep getting md5 invalid, any suggestions? Redownloaded 3 times and still a no go. Thanks
Sweet! Thx..
Sent from my SM-N900P using XDA Free mobile app
rogerandgina said:
I'm trying to flash this through Odin 3.07 and keep getting md5 invalid, any suggestions? Redownloaded 3 times and still a no go. Thanks
Click to expand...
Click to collapse
Same here...
rogerandgina said:
I'm trying to flash this through Odin 3.07 and keep getting md5 invalid, any suggestions? Redownloaded 3 times and still a no go. Thanks
Click to expand...
Click to collapse
Hmm maybe a bad upload. Let me do it again
freeza said:
Hmm maybe a bad upload. Let me do it again
Click to expand...
Click to collapse
Just wondering if you have the new upload uploaded?
rogerandgina said:
Just wondering if you have the new upload uploaded?
Click to expand...
Click to collapse
I just downloaded the tar file and tried changing the filename by removing .md5, leaving just the .tar extension. Odin started
but failed
I think the answer to your question is no
yep
no go
Has there been any benifits found in the new update? I
Sent from my SM-N900P using Xparent Skyblue Tapatalk 2
OP updated... I posting a different link, same file. I've had one person post success with it, so it was probably either a bad upload or my site not completing downloads.
@freeza sup bud. I have a question if I have mobile Odin and flash this will it affect my phone while I'm on NC5 or update the baseband then flash the stock rooted NH7 rom then reboot
Still a no go with updated op.
screenshot of what im getting
pancho8188 said:
no go
Click to expand...
Click to collapse
here is what im getting
Jocutz1987 said:
@freeza sup bud. I have a question if I have mobile Odin and flash this will it affect my phone while I'm on NC5 or update the baseband then flash the stock rooted NH7 rom then reboot
Click to expand...
Click to collapse
Unless Mobile Odin had changed recently, I believe that modems are about the only thing it won't flash correctly. PC Odin is the way to go for modem flashes (until someone puts together recovery flashable modem).
pancho8188 said:
here is what im getting
Click to expand...
Click to collapse
Strange.....one of my buddies was able to update it just fine.
I'll just go ahead and redo it.
freeza said:
OP updated... I posting a different link, same file. I've had one person post success with it, so it was probably either a bad upload or my site not completing downloads.
Click to expand...
Click to collapse
Worked for me.
Shows up in settings NH7 baseband
Works for me.
Sent from my SM-N900P using Tapatalk
xxDeletedxx Sorry guys
Goat1378 said:
I pulled this from the new 4.4.4 NK4/N900PVPUDNK4_SPR zip
Its just baseband. Odin flashable tar file.
Do the following and you should be good.
1) download the NK4 tar file from the link below.
2)Power your device down completely using the 3 button combo (Power,Volume down,Home button.
3)Fire up Odinv3.09 UNCHECK auto reboot and load your tar into slot AP and hit start.
4)After it does its thing and shows its done unplug your usb cord and pull your battery.
5)Leave your battery out for 10sec. and put it back in.
6)Use your 3 button combo once more to boot into Download mode.
7)This time make sure to check auto reboot.
8)Load the same tar file again and flash.
After its done you should be good to go. Basically I'm just using the steps suggested by freeza on the NH7 Baseband update. So give that guy thanks too while your at it.
Heres a link to the full release of NK4 when it was brought to us by shadowcliffs http://forum.xda-developers.com/note-3-sprint/general/stock-rom-n900pvpudnk4-released-t2987901 to see what all the fuss is about. Give shadowcliffs thanks for bring this to us when you get over there and any of the other guys if you find there info useful.
NK4 (Modem only) https://www.androidfilehost.com/?fid=95887005526788421
NK4 (Full Update) https://www.androidfilehost.com/?fid=95887005526788395
If i missed any steps anyone feel free to correct me. HAPPY MODDING!!!!!!!!
Click to expand...
Click to collapse
Is their a NK4 flashable kernel zip floating around anywhere yet ?
Alright Goat.. Thank you for this..
In the past, at least on my former Nexus devices, I was able to just flash new radios via a zip in recovery without needing to go home and hook up to my PC to use Odin - is that possible with the Note 3 as well?
I'm at work and would love to just download the radio and update in recovery if possible.
chico260 said:
Is their a NK4 flashable kernel zip floating around anywhere yet ?
Click to expand...
Click to collapse
I will try and pull it from the update and zip it up and post here in a bit.
Does anyone know of a flashable through recovery zip for the modem? I'm currently without a computer. Thanks in advance.
rogerandgina said:
Does anyone know of a flashable through recovery zip for the modem? I'm currently without a computer. Thanks in advance.
Click to expand...
Click to collapse
You can't flash the modem in recovery.
Goat1378 said:
You can't flash the modem in recovery.
Click to expand...
Click to collapse
I thought there was a way if packaged right.
rogerandgina said:
I thought there was a way if packaged right.
Click to expand...
Click to collapse
I thought so too...
22stars said:
I thought so too...
Click to expand...
Click to collapse
There might be a way but I'm no developer and I'm not gonna pack it without knowing what I'm doing. I've never seen a recovery flashable modem. Not saying theres not a such thing. But I done know how. Sorry. I'm sure if its possible someone will make it.
Link
Does anyone have an active link for the modem only? Please and thanks.
njspank said:
Does anyone have an active link for the modem only? Please and thanks.
Click to expand...
Click to collapse
Is it not working? Try it again.
I just downloaded for later tonight and it worked for me
Goat1378 said:
Is it not working? Try it again.
Click to expand...
Click to collapse
Hey Goat, I don't know nuthin, but shouldn't the tar.md5 file contain a .img file instead of a .bin file?
But again, I don't know nuthin..
oldjackbob said:
Hey Goat, I don't know nuthin, but shouldn't the tar.md5 file contain a .img file instead of a .bin file?
But again, I don't know nuthin..
Click to expand...
Click to collapse
I'm not entirely sure but if you want an image I got an image for you! Lol jk . Not not really sure . I dl the nh7 to see what it had in it. Did it not work? Ill get it rite sooner or later.
oldjackbob said:
Hey Goat, I don't know nuthin, but shouldn't the tar.md5 file contain a .img file instead of a .bin file?
But again, I don't know nuthin..
Click to expand...
Click to collapse
I just downloaded this from freezas nh7 baseband and this is whats inside. Which is what i had at first.
So now im lost in the game. Cuz someone told to that just the modem bin worked.??????
Goat1378 said:
I'm not entirely sure but if you want an image I got an image for you! Lol jk . Not not really sure . I dl the nh7 to see what it had in it. Did it not work? Ill get it rite sooner or later.
Click to expand...
Click to collapse
No sir, didn't work for me but I'm not using the recommended route, I'm using Mobile Odin Pro.
When I open Philz Touch tar.md5 file (which contains a recovery.img file) from inside Mobile Odin, it recognizes that it's a recovery partition image and "pre-loads" it into that partition slot for flashing. But when I open the nk4 baseband tar.md5 file (which contains a modem.bin file) in Mobile Odin it says "Partition could not be found in file".
oldjackbob said:
No sir, didn't work for me but I'm not using the recommended route, I'm using Mobile Odin Pro.
When I open Philz Touch tar.md5 file (which contains a recovery.img file) from inside Mobile Odin, it recognizes that it's a recovery partition image and "pre-loads" it into that partition slot for flashing. But when I open the nk4 baseband tar.md5 file (which contains a modem.bin file) in Mobile Odin it says "Partition could not be found in file".
Click to expand...
Click to collapse
I do know we couldnt use moblie odin to flash nh7 cuz i tried.
Goat1378 said:
I do know we couldnt use moblie odin to flash nh7 cuz i tried.
Click to expand...
Click to collapse
Fair enough, like I said, I don't know nuthin, so y'all prolly shouldn't be paying much attention to me, lol.
But I'm still wondering, has anyone had any success flashing the NK4 baseband yet?
I
oldjackbob said:
Fair enough, like I said, I don't know nuthin, so y'all prolly shouldn't be paying much attention to me, lol.
But I'm still wondering, has anyone had any success flashing the NK4 baseband yet?
Click to expand...
Click to collapse
Yeah someone else did from from someone else that posted the baseband. Not sure who. Screen shot of whats in the update.
Hey Guys and Gals:So I was able to pull the new OC5 TAR file from Samsung Kies and tough of shearing it with you
Here is the stock tar for OC5.
Recommended steps:
-Download file, unzip file to extract full tar.md5 file
-Load PC Odin (right-click on file, select "Run as Administrator")
-Unplug your phone from the computer (if plugged in)
-Completely power down your phone
-Boot into download mode (Volume Down+Power+Home)
-Plug your phone into the computer
-Load tar.md5 file into PDA slot in Odin
-Flash stock rom
DOWNLOAD LINKS:
MEGA:https://mega.co.nz/#!ZVBA0YjB!w4ymFFaRqwZZ620oX9hgwkZcoyJT0s7l31bhAHa4AIQ
GDRIVE:https://drive.google.com/file/d/0BxYsU5Xb_krEbkVNTXd6X3hPSlU/view?usp=sharing
ODIN(just in case some one need's it):http://odindownload.com/
Thanks for sharing. :good:
Sweet thank you so much this is going to come in handy
rlmiller said:
Sweet thank you so much this is going to come in handy
Click to expand...
Click to collapse
Hey Miller,are we going to get a rom out of this since the tar is out?
You bet.......soon
Yeah no problem I just want to see a good lollipop rom and I bet sac will come out with that!!!
How did you finally get it if I may ask? I know a lot of people were trying lol.
Sent from my SM-N900P using XDA Free mobile app
It's different to pull the tar file than the update.zip i try to pull the update.zip several times but it would get corrupted then I found out how to get the tar file and believe me it's a little complicated but I managed to get it for all of you!!!!
Has anyone tried to odin this yet? Does it truly work? Im at work and cant try it out. Anyone lmk. Thx
Hec1N1 said:
Has anyone tried to odin this yet? Does it truly work? Im at work and cant try it out. Anyone lmk. Thx
Click to expand...
Click to collapse
Yes, Odined it last night..Works great!
Jairsantana said:
Yeah no problem I just want to see a good lollipop rom and I bet sac will come out with that!!!
Click to expand...
Click to collapse
Thanks for sharing :good: :good: :good:
This will be done when I get home I hate base roll ups.a nice clean tar flash is where it's at..
Sent from my 0x1 Note 3...... I love tep
kaos420 said:
This will be done when I get home I hate base roll ups.a nice clean tar flash is where it's at..
Sent from my 0x1 Note 3...... I love tep
Click to expand...
Click to collapse
I hope we can get some fast kernels soon, I tried 2 and they wern't great, now I'm back to stock again.
I tried it 3 times each on 2 different devices using Odin 3.09 and each time it fails during the system write process. However, I tried the NK4 tar file and it worked no problem. Is it just me?
travisw0204 said:
I tried it 3 times each on 2 different devices using Odin 3.09 and each time it fails during the system write process. However, I tried the NK4 tar file and it worked no problem. Is it just me?
Click to expand...
Click to collapse
That happened to me as well..Then I installed the newest Samsung drivers and it worked.
Using it now too. Nice to have working data on lollipop
Sent from my SM-N900P using XDA Free mobile app
baseband still NH7
sorico said:
baseband still NH7
Click to expand...
Click to collapse
No
Its a tar it's oc5
Sent from my 0x1 Note 3...... I love tep
Ap: N900pvpueoc5
cp: N900pvpudnh7
csc: N900pspteoc5
sorico said:
Ap: N900pvpueoc5
cp: N900pvpudnh7
csc: N900pspteoc5
Click to expand...
Click to collapse
Try pulling your battery then going to DL mode from totally powered off. May take a couple flashes to stick as well.