Related
hi guys can anyone guide me to root the gingerbread mt6575?
Please!
touseefiqbal said:
hi guys can anyone guide me to root the gingerbread mt6575?
Click to expand...
Click to collapse
Hello, I am looking for a solution, but can not find. I could not rooting my Avvio 760 mt 6575 with Android 2.3.6 Gingerbread. PLEASE HELP!!! :crying:
solution
jheysonamc said:
Hello, I am looking for a solution, but can not find. I could not rooting my Avvio 760 mt 6575 with Android 2.3.6 Gingerbread. PLEASE HELP!!! :crying:
Click to expand...
Click to collapse
install usb vcom drivers first
i think i have found.. download mtkdroid tools and sp flash tool put usb debugging mode on and connect through usb and run mtkdroidtools when it detects then click on block maps i think.... now a table open click on create scatter... now scatter created...open sp flash tool..load scatter click on read back then double click on first page-only now choose page only then on lenght give the chache address from scatter when done click ok... take the battery out and connect your mobile through usb without battery.now click on read back when its done then tell me
1.Dowoad the file from the link below.
2. Then download Clockwork Mod Custom Recovery.
3. Then boot into recovery mode, and choose "install from SD Card".
4. Choose Clockwork mod recovery.zip, and it will boot you into a different recovery.
5. From that recovery mode you should be able to flash .zip files without signature verification.
6. Choose install zip from SD Card and choose SU Installer.zip.
Note:To unroot just flash SU Uninstaller.zip the same way you did to flash Installer.zip.
Downloads:
CWM Custom Recovery (Choose either Touch Recovery or Recovery for your device.):
http://clockworkmod.com/rommanager
SU Installer:
http://www.mediafire.com/?0r9dx4t1utvvuj0
SU Uninstaller:
http://www.mediafire.com/?c469p1nu64e92gf
Be sure to click dat THANKS button if I helped!
Sent from my GT-I9100 using xda premium
Avvio 760 Root!!!
Ronny927 said:
1.Dowoad the file from the link below.
2. Then download Clockwork Mod Custom Recovery.
3. Then boot into recovery mode, and choose "install from SD Card".
4. Choose Clockwork mod recovery.zip, and it will boot you into a different recovery.
5. From that recovery mode you should be able to flash .zip files without signature verification.
6. Choose install zip from SD Card and choose SU Installer.zip.
Note:To unroot just flash SU Uninstaller.zip the same way you did to flash Installer.zip.
Be sure to click dat THANKS button if I helped!
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
Dont Work Help Me!!!
hey
jheysonamc said:
Dont Work Help Me!!!
Click to expand...
Click to collapse
i tell you something why you didnt follow it?
jheysonamc said:
Hello, I am looking for a solution, but can not find. I could not rooting my Avvio 760 mt 6575 with Android 2.3.6 Gingerbread. PLEASE HELP!!! :crying:
Click to expand...
Click to collapse
Give some more details about ur phone, I can help u to root.
Sent from my A2 using xda app-developers app
touseefiqbal said:
hi guys can anyone guide me to root the gingerbread mt6575?
Click to expand...
Click to collapse
Download root genius for pc
Open it with administrator rights and root
Anyone has any idea how to root this latest phone QMobile NOIR A2 Classic?
It seems that old tricks for QMobile NOIR A2 (it's a different model) don't work with this model.
Try the root method available for qmobile noir a2 v3 method
Sent from my A2 using xda app-developers app
I have rooted my a2 classic
Sent from my A2_Classic using xda app-developers app
bilalz400 said:
I have rooted my a2 classic
Sent from my A2_Classic using xda app-developers app
Click to expand...
Click to collapse
Can you tell me how did you rooted A2 Classic and Provide some Screenshots of your rooted QMobile Noir A2 Classic?
bilalz400 said:
I have rooted my a2 classic
Sent from my A2_Classic using xda app-developers app
Click to expand...
Click to collapse
Please share the procedure of rooting A2 Classic.
I have tried almost everything but I have been unable to root it.
How did u root
bilalz400 said:
I have rooted my a2 classic
Sent from my A2_Classic using xda app-developers app
Click to expand...
Click to collapse
i have tried many methods but i was un successful, can u plz tell me the method u applied.
qmobilea2 said:
Try the root method available for qmobile noir a2 v3 method
Sent from my A2 using xda app-developers app
Click to expand...
Click to collapse
works like a charm on A2 Classic
Ok I will post method soon
Sent from my A2_Classic using xda app-developers app
un successful
threatalive said:
works like a charm on A2 Classic
Click to expand...
Click to collapse
i have tried but still un successful
How To Root Qmobile Noir A2 Classic
EDIT : THIS METHOD NO LONGER WORKS USE THIS METHOD http://forum.xda-developers.com/showthread.php?t=2380935
Things You Need:-
Adb Drivers http://ge.tt/2yL21VT
Mtk Root and Tools http://dfiles.ru/files/fmnok7ke7
Vcom Drivers
Windows 8 http://www.mediafire.com/?7yee2of64nhl947
WIndows 7/xp/vista http://www.mediafire.com/?cypm22rgs2k83ji
SP Flash Tool http://www.mediafire.com/?agsj3n4neniq054
Recovery Image http://www.mediafire.com/download/9g6eqmmb8b9mafi/A2_Classic_130302_recovery_130608-000343.img
Scatter File http://www.mediafire.com/view/rbg0jnclccctnpt/MT6575_Android_scatter.txt
Method :-
1. Open Smart Phone Flash Tool and load Scatter File (click "File" from the menubar and click "Scatter Loading file" and Select "MT6575_Android_scatter.txt".)
2. Tick ONLY THE RECOVERY OPTION and select the recovery image
3. Turn off your phone ,remove the battery and reinsert it and click the download button on sp flash tool and connect the usb and wait for the
flashing to complete.
4. You will see a green circle indicating flash is successfull
5. Remove the USB turn on the phone in recovery mode by pressing power and volume up button
6. Dont Do anything in recovery and connect the phone to the usb when the phone is in the recovery mode
7. Your computer will recognize the phone
8. Open MTK Droid Root and tools
9. It will also recognize the phone and display some information about the phone if so then click the "root,backup and recovery" tab
10. First Click the Backup option , It Will backup your entire Phone software so if you mess anything up you can restore it back
11. then click super user button it will root your phone it will ask you for root managing application its up to you which one you want i choosed
super user after it has finished reboot your phone by selecting the reboot system now option on your phone recovery and entering it by
pressing power key
12 . Check your phone for superuser application IF it has then CONGRATULATIONS your phone is rooted
If the Super user application does not launch turn on debugging mode
Press Thanks IF i Helped
trm33 said:
i have tried but still un successful
Click to expand...
Click to collapse
you must be missing something!
try again by closely following the steps in the above post by @bilalz400
threatalive said:
you must be missing something!
try again by closely following the steps in the above post by @bilalz400
Click to expand...
Click to collapse
By the way smart phone flash tool has to be version specific, other versions for some reasons dont work with this phone, download the one from the link on my post
threatalive said:
you must be missing something!
try again by closely following the steps in the above post by @bilalz400
Click to expand...
Click to collapse
MTK droid tools does not recognize fone in recovery mode, however 1st 3 steps are successful
Which recovery are you getting?? confirm it is cwm recovery ( it is blue) or any other?? If it is cwm then use this method which does not require mtk droid tool
Put the zip file I attached. In sd card (dont put in any folder)
In recovery mode select "update from sd card" (to navigate in recovery mode ,press vol + to go up, vol - to go down and power key to enter) and select the zip file once it is complete reboot your phone by selecting "reboot system now" it will be rooted inshallah
Zip file http://db.tt/owvX0f7t
Sent from my A2_Classic using xda app-developers app
trm33 said:
MTK droid tools does not recognize fone in recovery mode, however 1st 3 steps are successful
Click to expand...
Click to collapse
Is step 4 successful, I mean do you see the green circle?
If yes, then you must have CWM recovery in which case you may skip further steps if MTK is not recognizing and instead use alternate method given by @bilalz400 in above post.
I apply your method, this error is showing
RaoTayyab said:
I apply your method, this error is showing
Click to expand...
Click to collapse
Double check is your sp flash tool ver is 3.1224 because this error comes on other versions
plz check the error
its not cwm recover its defaulat "android recovery 3e", i was thinking that i was successful in above 4 steps b/c it was showing 100% bar after than i m receiving this error picture attached. version of flash tools is SP_Flash_Tool_v3.1224.01
@threatalive which sp flash tool do you use
Sent from my A2_Classic using xda app-developers app
I use this method, showing error ... whats should i do... where the problem with me....
Anyone can help will be very much appreciated.
It is this model = http://www.lelong.com.my/zte-v793-a...alcatel-hidamari-129512382-2014-05-Sale-P.htm
I also have this phone and still looking for a working method to root it. Please share the info if you know. Thank you.
ZTE V793 rooted
rooted my zte v793 successfully
i used the SP Flash tool to obtain scatter file and use that file to modify CWM from zte blade using MTK Droid tools. Then i flash the recovery image to the phone using SPF tool.
then using CWM, i flashed Root_Superuser_3.1.3_Busybox_1.20.2-Update1-signed.zip to the phone.
Then i use Link2SD and partitioned my sdcard to offload files from the meagre 100MB limitation
i will put the detailed procedure and the customised CWM for v793 if that's needed so you don't have to mess around with those files.
thanks
zte v793
kokokranc said:
rooted my zte v793 successfully
i used the SP Flash tool to obtain scatter file and use that file to modify CWM from zte blade using MTK Droid tools. Then i flash the recovery image to the phone using SPF tool.
then using CWM, i flashed Root_Superuser_3.1.3_Busybox_1.20.2-Update1-signed.zip to the phone.
Then i use Link2SD and partitioned my sdcard to offload files from the meagre 100MB limitation
i will put the detailed procedure and the customised CWM for v793 if that's needed so you don't have to mess around with those files.
thanks
Click to expand...
Click to collapse
1. Can u teach me how to root zte v793 step by step and give also download link?
2. I also have another problem : after update zte v793 my phone keep restarting...
kokokranc said:
rooted my zte v793 successfully
i used the SP Flash tool to obtain scatter file and use that file to modify CWM from zte blade using MTK Droid tools. Then i flash the recovery image to the phone using SPF tool.
then using CWM, i flashed Root_Superuser_3.1.3_Busybox_1.20.2-Update1-signed.zip to the phone.
Then i use Link2SD and partitioned my sdcard to offload files from the meagre 100MB limitation
i will put the detailed procedure and the customised CWM for v793 if that's needed so you don't have to mess around with those files.
thanks
Click to expand...
Click to collapse
Hi
Can you teach us step by step to root zte v793 and the link to download the software you use.
kokokranc said:
rooted my zte v793 successfully
i used the SP Flash tool to obtain scatter file and use that file to modify CWM from zte blade using MTK Droid tools. Then i flash the recovery image to the phone using SPF tool.
then using CWM, i flashed Root_Superuser_3.1.3_Busybox_1.20.2-Update1-signed.zip to the phone.
Then i use Link2SD and partitioned my sdcard to offload files from the meagre 100MB limitation
i will put the detailed procedure and the customised CWM for v793 if that's needed so you don't have to mess around with those files.
thanks
Click to expand...
Click to collapse
edit: I also in need of usb driver for this phone because whenever I switch off phone for Flash tool, my XP laptop always ask for drivers of which I don't have.
Thank you in advance. I'll wait for your files and guidance to do it. :good:
Dear all,
my method ultimately becomes obselete now. to root, you can just use one of these 2 methods:
1. Ishuaji
2. e-root
the supersu included is in chinese, so you might need to flash CWM to change to english supersu.
as for flashing CWM, you can find tutorials using Mobileuncle.
thanks!
First, disclaimer:
WE TAKE NO CREDIT FOR ANY WORK THAT COMES ASSOCIATED WITH THESE BUILDS UNLESS SPECIFIED OTHERWISE. THANKS FOR KEEPING THINGS OPEN!
OFFICIAL DISCLAIMER
PHP Code:
Code:
#include
/*
* Your warranty is now void.
*
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about this custom CWM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at me for messing up your device, I will laugh at you.
*/
All the files needed are in this google drive folder:
https://drive.google.com/folderview?id=0BzFjevWXftUyY3RQUlZjZ2s1QjA
Detail of files:
1. zte_mtk6573_drivers_cdc+vcom+adb_v1.1136.0.zip
USB VCOM driver. needed when you want to flash the phone (This is when you strip the battery off the phone and connect it to USB). this driver is unsigned, so for win8 users, pls google how to install unsigned drivers.
2. SP Flash Tool v3.1216.05.7z
Flashing tool. you need this to flash the custom CWM attached.
3. MT6575_Android_scatter.txt
Device-specific memory map. we need this to tell SP flash tool where to put the custom CWM when flashing.
4. ZTE-V793_130615__recovery_130802-123951.img
Custom CWM generated from my phone (ZTE V793) bought from Happy Mobile (DiGi) under SKMM package.
DISCLAIMER: this is generated from my phone's settings and intended only for my phone's usage. I will not be responsible for any damage caused by your act of flashing this file onto your phone.
I successfully generated the file using the tutorial from a russian site
http://forum.china-iphone.ru/viewtopic.php?p=496116#p496116
also an xda tutorial here
http://forum.xda-developers.com/showpost.php?p=38337401&postcount=5
You can generate your own CWM using tutorials above, but if you agree with the disclaimer, you can use the custom recovery attached. With no warranties, of course.
5. Root_Superuser_3.1.3_Busybox_1.20.2-Update1-signed.zip
The rooting tool to be installed by our custom CWM to the phone to obtain root
Click to expand...
Click to collapse
Method:
This can be divided into several process:
1. Download all related files
2. Install Driver
3. Flash custom CWM
4. Install Root & Busybox zip file using CWM
Click to expand...
Click to collapse
1. Download all related files
Pretty self explanatory. Download and extract all files.
First, download and install USB Driver:
http://www.mediafire.com/download/f7h1f7i7skggmtg/ZTE+Driver.rar
2. Install Driver
We need 2 drivers to be installed:
- ZTE_Handset_USB_Driver.exe
- JoinMe_for_Android.exe
the Joinme driver is needed when flashing custom CWM. However, it didn't work for me. so I installed zte_mtk6573_drivers_cdc+vcom+adb_v1.1136.0.zip manually. To install it, remove battery from phone, connect to usb. Wait for computer to start searching for drivers, select Browse for drivers and select the vcom drivers downloaded.
3. Flash custom CWM
1. Open Flash_tool.exe from SP Flash Tool v3.1216.05 folder extracted earlier.
2. Click "Scatter-loading". Select "MT6575_Android_scatter.txt" that you downloaded earlier.
View attachment 2159248
3. Click to deselect ALL checkboxes in the list. ONLY TICK RECOVERY.
View attachment 2159266
4. Double click on the word RECOVERY and select "ZTE-V793_130615__recovery_130802-123951.img" downloaded earlier
View attachment 2159267
5. Click Download. A warning will pop up "Not ALL images are correctly loaded blah blah blah". just click Yes.
View attachment 2159283
6. If you see below the application, it will say "Searching" next to NAND. Time to plug in your phone. DON'T FORGET TO REMOVE THE BATTERY BEFORE PLUGGING IN YOUR PHONE.
View attachment 2159284
View attachment 2159285
7. Now you're done flashing, it's time to boot into CWM. Unplug the phone from USB. Put on battery. Press Vol+ & Power Button simultaneously. When ZTE logo appear, RELEASE ALL BUTTON.
8. Let's hope you boot straight into CWM
If you have this, then CONGRATULATIONS! you are now a step away from root!
4. Install Root & Busybox zip file using CWM
1. Copy the "Root_Superuser_3.1.3_Busybox_1.20.2-Update1-signed.zip" onto the root of SD Card on your phone as normally you would (I wouldn't elaborate since this is android 101 knowledge)
2. Boot into Clockworkmod (CWM) recovery. To do this, turn off your phone normally. 5 seconds after the phone vibrates (fully off), press volume up (vol+) and power button. Wait until ZTE logo appears, then release both buttons.
If you do this correctly, you will see "CWM v 5.5.0.4 for ZTE V"
to navigate, use volume up (vol+) & volume down (vol-). to select, use power button.
3. Select "install zip from SD CARD" > "Choose zip from sdcard" > Look for "Root_Superuser_3.1.3_Busybox_1.20.2-Update1-signed.zip". REMEMBER: Navigate using volume button, select using power button.
then, confirm by selecting "Yes - Install Root_Superuser_" and pressing power button.
when completed, go back to main menu and select reboot.
if nothing goes wrong, you will see SuperUser and busybox icon in your App drawer.
UPDATE:
12082013 - finished 4th item - install root & busybox
todo - revise SP Flash tool version
kokokranc said:
4. Install Root & Busybox zip file using CWM
Can I continue next time? wow, doing this is such a pain. i never knew that. kudos to all the gurus who are willing to spend their time making guides and walkthroughs.
thanks
Click to expand...
Click to collapse
Hi kokokranc..appreciate if you could continue
Will Try
kokokranc said:
First, disclaimer:
If you have this, then CONGRATULATIONS! you are now a step away from root!
4. Install Root & Busybox zip file using CWM
Can I continue next time? wow, doing this is such a pain. i never knew that. kudos to all the gurus who are willing to spend their time making guides and walkthroughs.
thanks
Click to expand...
Click to collapse
want to try it after buaka puasa :laugh:
error
got this error
maybe it because my pc just detects then undetects preloader drivers
my phone cannot power after format using spf tools
TQ for your full tutorial but i having problem after formating using spf tools....my phone zte v793 cannot turn on...can u help me plzz...
Cannot On
pendaflour said:
TQ for your full tutorial but i having problem after formating using spf tools....my phone zte v793 cannot turn on...can u help me plzz...
Click to expand...
Click to collapse
same here
saifudinbesoot said:
got this error
maybe it because my pc just detects then undetects preloader drivers
Click to expand...
Click to collapse
When the red bar reaches 100% just disconnect and reconnect phone before timeout.
Sent from my GT-I9500 using xda app-developers app
---------- Post added at 02:54 AM ---------- Previous post was at 02:49 AM ----------
pendaflour said:
TQ for your full tutorial but i having problem after formating using spf tools....my phone zte v793 cannot turn on...can u help me plzz...
Click to expand...
Click to collapse
saifudinbesoot said:
same here
Click to expand...
Click to collapse
Log file from spf tool?
Sent from my GT-I9500 using xda app-developers app
thanks bro
all success after i use latest Flash_tool.exe from SP Flash Tool
it also solve this guy prob bec mine also like him
saifudinbesoot said:
got this error
maybe it because my pc just detects then undetects preloader drivers
Click to expand...
Click to collapse
pls continue to Install Root & Busybox zip file using CWM
sadmanex said:
thanks bro
all success after i use latest Flash_tool.exe from SP Flash Tool
it also solve this guy prob bec mine also like him
pls continue to Install Root & Busybox zip file using CWM
Click to expand...
Click to collapse
do u manage to get into CWM like the last screenshot above?
Sent from my ZTE V793 using xda app-developers app
Error 8038
Please help, my phone is still OK, can ON, but I got this error. I've tried another version of SP Flash Tool but still got the same error..
Root Success
kokokranc said:
First, disclaimer:
WE TAKE NO CREDIT FOR ANY WORK THAT COMES ASSOCIATED WITH THESE BUILDS UNLESS SPECIFIED OTHERWISE. THANKS FOR KEEPING THINGS OPEN!
OFFICIAL DISCLAIMER
PHP Code:
Code:
#include
/*
* Your warranty is now void.
*
.
.
.
.
[COLOR="Red"][B]4. Install Root & Busybox zip file using CWM[/B][/COLOR]
Can I continue next time? wow, doing this is such a pain. i never knew that. kudos to all the gurus who are willing to spend their time making guides and walkthroughs.
thanks[/QUOTE]
Of course you can. Btw, I successfully root my phone using your recovery.img and scatter file. The only thing I need to change is SP Flash Tool. I downloaded new version SP_Flash_Tool_v3.1224.01, because your provided version doesn't work for me.
Anyway, thank you very much for all the files.
Click to expand...
Click to collapse
kokokranc said:
do u manage to get into CWM like the last screenshot above?
Sent from my ZTE V793 using xda app-developers app
Click to expand...
Click to collapse
yes
and can on/start my phone normally
just use new SP_Flash_Tool_v3.1224.01 (download at softpedia)
cannot on phone
some have link to download PRELOADER image?plzzz share...my phone cannot on after flash format...
saifudinbesoot said:
same here
Click to expand...
Click to collapse
pendaflour said:
TQ for your full tutorial but i having problem after formating using spf tools....my phone zte v793 cannot turn on...can u help me plzz...
Click to expand...
Click to collapse
remove your battery and replace it again, and then turn on. I got the same problem back then and those steps worked for me.
Please help me I want to install custom recovery on my karbonn titanium MACHFIVE.
This phone running on lollipop 5.0. & it have MediaTek MT6582 1.3 GHz Quad-core processor
&2GB of RAM & 16GB internal memory.
have you rooted your fone
need root
i know machfive is new in the market but really need at least rooting method for it cause it have some bugs though pls pls pls developers we are relaying on you for this
Yes
farhanfarhan32 said:
have you rooted your fone
Click to expand...
Click to collapse
I have rooted phone.
I root with kingroot
mukulkumars13 said:
I have rooted phone.
I root with kingroot
Click to expand...
Click to collapse
kingo root does not worked for me
Use iroot it worked for me
Need recovery for it man..... Xposed is also need to flash zip n i dont hav recovery damn!!
ajju akm said:
Use iroot it worked for me
Click to expand...
Click to collapse
kingo root , iroot , towel root, every thing failed:crying::crying:
I just rooted with iroot windows application.
ashish128 said:
I just rooted with iroot windows application.
Click to expand...
Click to collapse
which version of iroot you used?
root with kingroot
i used kingroot ver. 4.0.0 and it works try it out
after root u can use http://forum.xda-developers.com/showthread.php?t=2379412 to make recovery for ur machfive as it is a mediatek device
hit thanks if i helped
ajju akm said:
i used kingroot ver. 4.0.0 and it works try it out
after root u can use http://forum.xda-developers.com/showthread.php?t=2379412 to make recovery for ur machfive as it is a mediatek device
hit thanks if i helped
Click to expand...
Click to collapse
king root 4.0 worked:laugh:
farhanfarhan32 said:
king root 4.0 worked:laugh:
Click to expand...
Click to collapse
Hi
Just bought this phone for my friend. While trying to root with kingroot v4 and 4.5 its does not works.. Can u tell me ur frmware version number ?
Is there any recovery for this phone Karbonn Titanium Machfive.
Thanks in advance.
Sent from my MACHFIVE using Tapatalk
phone stuck in boot loop after kingroot 4.5. what to do?
model karbonn mach five.
Ya my phone too struck in karnonn logo after updating su binary...
Please anyone provide the factory image of karbonn titanium mach five ASAP..
And also provide instructions for flashing the image
Device: Karbonn Titanium Mach Five
Status: Rooted, No custum recovery installed, Bootloop...
Kingroot 4.0 worked. Rooted successfully
Sent from my MACHFIVE using Tapatalk
Recover KARBONN TITANIUM MACHFIVE
rockybilla007 said:
Ya my phone too struck in karnonn logo after updating su binary...
Please anyone provide the factory image of karbonn titanium mach five ASAP..
And also provide instructions for flashing the image
Device: Karbonn Titanium Mach Five
Status: Rooted, No custum recovery installed, Bootloop...
Click to expand...
Click to collapse
The last week I had a similar issue stuck on KARBONN logo.
I used Stock from XDA Firmware xdafirmware.com/karbonn-mach-five
Download the necessary drivers (a must) .
The downloaded compressed file will have SP flash tool with it .
1 .Open "flash_tool.exe" under "\SP Flash Tool v5.1516" folder (with admin privileges) .
2 .Navigate to the "Download" section .
3. Click on the "Scatter-loading". Browse "MT6582_Android_scatter.txt" under "Firmware" .
4. Now this will give you a list of files to flash that comes from the "\Firmware" folder . Make sure every files load correctly to the list(location can be seen to the right of the item to be flashed) . Especially "Android" which correspond to the system.img file in the \Firmware which I think which actually solves the android system related files' problems.
5. Now Power off your phone .
'''Wait for a sec ( many people advice removing the battery for a while).
6. Now click on the Download sign in the SP flash tool window . Connect your phone with the USB cable immediately and click on the volume up or down for SP flash tool to detect your phone. If the phone gets detected SP flash tool throws some info on the left pane. Then the files will start flashing . Flashing status is provided by a yellow bar at the bottom of the window.
7. After the flash is complete a green ok popup.
8. Boot your phone to recovery and Wipe the cache partition.
9. Restart the phone.
This worked with my MACHFIVE . Wishing you luck :good:.
*Flashing always have a risk of bricking your phone. Think twice before you act . I will not take responsibility.
*Always take any errors in SP flash tool seriously and consult expert advice before continuing
*Even if you are stuck on boot if you have enabled USB debugging you can use adb pull to pull your data from memory.
greentoy said:
The last week I had a similar issue stuck on KARBONN logo.
I used Stock from XDA Firmware xdafirmware.com/karbonn-mach-five
Download the necessary drivers (a must) .
The downloaded compressed file will have SP flash tool with it .
1 .Open "flash_tool.exe" under "\SP Flash Tool v5.1516" folder (with admin privileges) .
2 .Navigate to the "Download" section .
3. Click on the "Scatter-loading". Browse "MT6582_Android_scatter.txt" under "Firmware" .
4. Now this will give you a list of files to flash that comes from the "\Firmware" folder . Make sure every files load correctly to the list(location can be seen to the right of the item to be flashed) . Especially "Android" which correspond to the system.img file in the \Firmware which I think which actually solves the android system related files' problems.
5. Now Power off your phone .
'''Wait for a sec ( many people advice removing the battery for a while).
6. Now click on the Download sign in the SP flash tool window . Connect your phone with the USB cable immediately and click on the volume up or down for SP flash tool to detect your phone. If the phone gets detected SP flash tool throws some info on the left pane. Then the files will start flashing . Flashing status is provided by a yellow bar at the bottom of the window.
7. After the flash is complete a green ok popup.
8. Boot your phone to recovery and Wipe the cache partition.
9. Restart the phone.
This worked with my MACHFIVE . Wishing you luck :good:.
*Flashing always have a risk of bricking your phone. Think twice before you act . I will not take responsibility.
*Always take any errors in SP flash tool seriously and consult expert advice before continuing
*Even if you are stuck on boot if you have enabled USB debugging you can use adb pull to pull your data from memory.
Click to expand...
Click to collapse
Sir thank you so much for replying have been waiting for weeks for the solution..
1)Downloaded the files
2)Installed drivers
3)Started flash tool and loaded scatter file
4)Clicked on download
5)Powered off phone and connected via usb
6)Flashing process started
7)Flashing finished and green ring appeared!!!
8)Device booted after some time.
Thanks again for the solution :good::good::good:
Thanks for the guide.
Did anyone made custom recovery for this phone yet. If anyone has a recovery kindly share here.
Sent from my MACHFIVE using Tapatalk
Bros...help me to unbrick My HCL me connect 3G 2.0 tab...i need the stock rom?
Deadman jo said:
Bros...help me to unbrick My HCL me connect 3G 2.0 tab...i need the stock rom?
Click to expand...
Click to collapse
Here you go :
https://docs.google.com/uc?id=0B0DGQDSsarOAdG1pd1pZTjFobE0&export=download
i need HCL me connect 3G 2.0tabs Stock recovery
Deadman jo said:
i need HCL me connect 3G 2.0tabs Stock recovery
Click to expand...
Click to collapse
Stock recovery should be included in the stock rom package unless you mean custom recovery.
MigoMujahid said:
Here you go :
https://docs.google.com/uc?id=0B0DGQDSsarOAdG1pd1pZTjFobE0&export=download
Click to expand...
Click to collapse
Bro i cant flash this rom on sp flash tool
Deadman jo said:
Bro i cant flash this rom on sp flash tool
Click to expand...
Click to collapse
As far as i know, you use mp tool not sp flash tool.
http://hulkload.com/pjj60j5hx6mt
Deadman jo said:
Bro i cant flash this rom on sp flash tool
Click to expand...
Click to collapse
this rom only flash with stock recovery im lost my stock recovery..
Flash with Digma iDND7 firmware.
Deadman jo said:
this rom only flash with stock recovery im lost my stock recovery..
Click to expand...
Click to collapse
I have one but the file is locked ... since a year now
Also I tried flashing the stock rom gives this error :
Error: Invalid partition setting
17: fat 979e8000:84de8000
installation aborted
Please help or suggest
++++++++++++++++++++++++++++++++++++
Deadman jo said:
this rom only flash with stock recovery im lost my stock recovery..
Click to expand...
Click to collapse
So there is an update I was able to successfully Flash a firmware from same board which was used by HCL me connect 3G 2.0.
I searched this for 3 days and found that Digma idnd 7 tab used the same board , so I hunted for Digma firmware and luckily got them, the file link contains both ota and Flash file via MP tool.
I tried ota update but I got the same error.
So I used MP flash tool v5.1352.01
Download adb drivers of HCL me tablet.
Extract the zip, then edit the scatter file name to "MT6577_Android_scatter_emmc".
Now open SP flash tool and choose the scatter.
Click on download and then plug the tab in using the USB.
Then I got some PMT file needs to be updated error which was fixed by the next step.
Stop the download, pull the device out, then click Format options in the 2nd tab and then "Format except Bootloader".
Plug the device in.
once the format is done, plug out again, click download(make sure scatter is selected).
Plug in the device.
It will start flashing.
File links :
HCL USB drivers : androidmtkDOTcom/download-hcl-usb-driver
SP flash links : androidmtkDOTcom/smart-phone-flash-tool
Digma original firmware : Unable to post link so : use google and search supportdotdigma
ps: may be this helps digmaDOTru/catalog/item/1344
Also you will need to change the language to English after Booting up.
Click on the equalizer>> click on icon marked A[use some common sense that's what I did xD] then inside that tap on the very , top of the submenu, you will get the option to change to English.
Please let me know if if works for you. Or you need any thing.