Related
Hello Friends,
i have found many queries regarding how to get stock recovery back...therefore i am presenting the solution of it....
->Requirements
Stock Recovery Image(in attachments)
Scatter Loading File(in attachments)
Micromax A116 Drivers(32bit/64bit)
SP Flash Tool
A computer
A Micromax A116 (obviously)
->Steps
1. Install drivers for your phone using Micromax drivers.
2. Extract the Stock ROM folder and replace recovery.img with cwm recovery.
3. Extract and open the SP Flash Tools.
4. In SP Flash Tools, click on Scatter-Loading and the program will ask you the location of the scatter loading file for your device.
5. select the file "MT6589_Android_scatter_emmc" which is our scatter loading file.
Check only recovery.img and uncheck all others.
6. Switch off your phone (Remove the battery to make sure it is switched off).
7. In Flash Tool, go to Options and Click USB Mode so that it is enabled. Click options again and then go to DA Download All > Speed and finally select High Speed.
8. Click the Download option (present on the right of Firmware
> Upgrade option) and the flash tool will start looking for your phone.
9. Connect your phone now. The Flash Tool will start the flashing process, the progress of which can be viewed from a yellow progress bar at the bottom of the flash tool.
**Don't interrupt this process as it can potentially brick your device.
**Make sure no power interruption takes place. (Use a laptop to ensure this).
10. After the process completes, a green ring will appear on your device signalling that the process was successful.
11.Disconnect your phone.
Great Work Man
Great Work Buddy!!!!!!!!!!
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser or SuperSU at least 2.16, no less.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip or SuperSU on your SDCARD. Remember: only one is good. DO NOT FLASH BOTH. Flash the one you like.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 or the newest one TWRP 2.8.4.0 rev 2 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119 or SP_Flash_Tool_v5.1352.01. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum in SP Flash Tool v3. In SP Flash Tool v 5 dont need. They are allready selected. Recovery.img should appear checked.
10.1. I have updated the post with some custom scatter files for 4GB and 8GB Firmware. Iff you get diferent errors when you flash the recovery file use this custom scatter files.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Then boot directly to recovery your phone by pressing power with vol + and vol - butons together. Not Optional!
15. From TWRP flash Superuser.zip or SuperSU 2.xx. SuperSU is fixed. Works fine now.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback.
Update:
I have uploaded TWRP Corrected by Javum. Thanks Javum. And it is working on ROW 226 and 227 tested personaly by installing patches, superuser and making backups.
Sent from my Lenovo P780
SP Flash Tool_v.3 and v.5
stympy said:
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have the latest FlashTool.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
Click to expand...
Click to collapse
This method did not work i got this error
"pmt changed for the rom it must be downloaded"
astrokid1993 said:
This method did not work i got this error
"pmt changed for the rom it must be downloaded"
Click to expand...
Click to collapse
Try to use Firmware Upgrade buton.
Or: You need to edit the file MT6589_Android_scatter_emmc.txt section USRDATA 0x48d80000 on USRDATA 0x58980000.
Waiting for feedback.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Point no 12 doesn't work with me, Anything I should know?
asambe2dumb said:
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Point no 12 doesn't work with me, Anything I should know?
Click to expand...
Click to collapse
If the 12 point doesn't work it means that you don't have the driver installed or installed correctly. Check the drivers.
Sent from my Lenovo P780 using XDA Free mobile app
all steps are done but not succsses
Hallo... IN my lenovo p780 with officaly updated android 4.4.2 and not rooted phone .I fallow all steps carrectly as u discribed after press download button when I connect my switched off phone I got mtp error than I edit scatter file user data as describe in comment section after that I press download and connect my p780 switched of all process done smuthaly I got green circles that's mean I am done after that I switched on phone and switched off phone for boot in recovery I press vol+ vol- and power buttons but their is not twrp recovery option ..only stock recovery option .
Pls help bro ...what I am doing wrong?. Or any other way to do this ?
Thanks for this wonderful tutorial.
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder  )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback. 
Update:
I have uploadet TWRP Corrected by Javum. Thanks Javum. And it is working on ROW 221 tested personaly by installing patches, superuser and making backups.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
Sent from my Lenovo P780 using XDA Free mobile app
I have not rooted lenovo p780 official updated to android 4.4.2 s221 OK I want root my phone I try every thing like pharma root. One click root ;rescue root;vroot ;kingoroot;and many other which I don't remember but not success ..OK than I try to follow your method ...first when I connect my switched off phone downloading process start after red bar complete I got mtp error
Then I edit scatter file user data section as u mansion in comments sections after that download has done withouts error I got green circle that's mean I am done ... OK I disconnect phone from computer and power on than switched off for boot in recovery ... I press power button + vol up and down together but their is ...
NOT TWRP RECOVERY .. only stock android recovery huuh what I do now ..where I am wrong any suggestion plz help
And thanks for this wonder full tutorial.
pu04 said:
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder  )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback. 
Update:
I have uploadet TWRP Corrected by Javum. Thanks Javum. And it is working on ROW 221 tested personaly by installing patches, superuser and making backups.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
Sent from my Lenovo P780 using XDA Free mobile app
I have not rooted lenovo p780 official updated to android 4.4.2 s221 OK I want root my phone I try every thing like pharma root. One click root ;rescue root;vroot ;kingoroot;and many other which I don't remember but not success ..OK than I try to follow your method ...first when I connect my switched off phone downloading process start after red bar complete I got mtp error
Then I edit scatter file user data section as u mansion in comments sections after that download has done withouts error I got green circle that's mean I am done ... OK I disconnect phone from computer and power on than switched off for boot in recovery ... I press power button + vol up and down together but their is ...
NOT TWRP RECOVERY .. only stock android recovery huuh what I do now ..where I am wrong any suggestion plz help
And thanks for this wonder full tutorial.
Click to expand...
Click to collapse
By any chance is your phone made in 2014 ?
Then if it is use preloader. Check preloader and try this one.
Its one year old phone ..with jelly bin 4.2.2 now I updated to 4.4.4 originally by ota ..I want to root it actually in mtk toot its show this massage `` ATTENTION! File /system/recovery-from-boot.p which restore factory recovery in case of phone switching on in a normal mode Is Found!
I don't know but I think its affect ..can u pls explain it what's this mean.
Thanks for reply ...I try with bootloder next day
Sent from my Lenovo P780 using XDA Free mobile app
Will it work on S214 also or should i instal S221 for my phone
astrokid1993 said:
Will it work on S214 also or should i instal S221 for my phone
Click to expand...
Click to collapse
For me worked on both.
Sent from my Lenovo P780
Thanksgiving
OK....FIRST I HEARTILY THANKS TO U ..NOW I AM SUCCESS ..finally rooted my lenovo p780 4.4.2 KitKat updated phone ..without any error or bricking my phone .. Thanks for this wonder full tutorial ..
As I mentioned previous reply that I got error from Sp flash tool ..something pmt error ..than as u sugest i edit user data section in scatter data section and flash it ..but nothing happen their is only stock recovery .. Today i retry process ..
1- follow all steps as it is
2 - for pmt error change user data section 3- at last u advise that power on phone then reboot in recovery by pressing volume+'- +power button at this stage ..what I have done ..is
I don't on my phone ..after flashing recovery I direct go to recovery using power + volume up+ volume down ..and waaaala here is done I got twrp custom recovery .. But don't flase superuser .zip just shutdown phone and on go to normal mode and check every thing is fine ..now power off go to recovery ...there is twrp present ..in recovery install super user ..just unchake verify check mark its install without any error ..and ..GOT ROOTED ..
Conclusion - why I unsuccessful in first time I don't know but think..I have this type of file .. File /system/recovery-from-boot.p which restore factory recovery in case of phone switching on in a normal mode Is Found! I think its prevent twrp when I normally switch on phone ..so this time I don't on phone go to direct recovery and all is done .. I got custom recovery..
AT last I thank you again for this great tut. Its worked for me finally .
Sent from my Lenovo P780 using XDA Free mobile app
stympy said:
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback.
Update:
I have uploadet TWRP Corrected by Javum. Thanks Javum. And it is working on ROW 221 tested personaly by installing patches, superuser and making backups.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
Click to expand...
Click to collapse
Friend, first time I follow all your steps to install TWRP , but it failed . And I see your reply in this thread and change the USR DATA . But it failed again , MY PHONE WAS BRICKED !!!!! IT DONT DO ANY RESPONSE , CANT POWER ON , CANT CONNECT TO COMPUTER , CANT GO TO RECOVERY . IT ONLY SHOW A RED LIGHT WHEN CHARGING . HOW TO SOLVE THIS PROBLEM ??? PLEASE HELP ME ...
stympy said:
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback.
Update:
I have uploadet TWRP Corrected by Javum. Thanks Javum. And it is working on ROW 221 tested personaly by installing patches, superuser and making backups.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
Click to expand...
Click to collapse
Not working at all for me i did everything correctly till point 11 when i connect my phone as in point 12 my phone starts charging and nothing is getting detected in the sp flash tool.
Any one please help me with my problem
tngultimate said:
Friend, first time I follow all your steps to install TWRP , but it failed . And I see your reply in this thread and change the USR DATA . But it failed again , MY PHONE WAS BRICKED !!!!! IT DONT DO ANY RESPONSE , CANT POWER ON , CANT CONNECT TO COMPUTER , CANT GO TO RECOVERY . IT ONLY SHOW A RED LIGHT WHEN CHARGING . HOW TO SOLVE THIS PROBLEM ??? PLEASE HELP ME ...
Click to expand...
Click to collapse
Your phone seems to be produced in 2014. For this phones must do this:
1. Must flash with another preloader.
Look for this ROM : P780_S136_140306_Lang.7z
Flash this Rom then OTA update.
Then tell me if it works.
Sent from my Lenovo P780
astrokid1993 said:
Not working at all for me i did everything correctly till point 11 when i connect my phone as in point 12 my phone starts charging and nothing is getting detected in the sp flash tool.
Any one please help me with my problem
Click to expand...
Click to collapse
Did you installed the drivers?
Did you presed the firmware upgrade first and then plugged the phone?
Update
Try this:
Press Download and open the case of your phone and press the little red buton for 2 seconds.
Sent from my Lenovo P780
stympy said:
Did you installed the drivers?
Did you presed the firmware upgrade first and them plugged the phone?
Sent from my Lenovo P780
Click to expand...
Click to collapse
I installed driver already... My phone now cant do anything... Help me please ...
tngultimate said:
I installed driver already... My phone now cant do anything... Help me please ...
Click to expand...
Click to collapse
Hi.
Do not panic. Your phone is just soft bricked.
Here is the link to download what you must flash first:
https://drive.google.com/folderview?id=0B2ORIgaV4iacT01mTm5JVzFuRGs&usp=sharing
And now here's a little tutorial how to save your phone. You should respectit exactly.
Step by step you will do this:
>>>>> USE WINDOWS 7 FOR THIS TUTORIAL <<<<<<<<<<<
>>>>>>>>>>REMOVE THE USB CALBLE FROM PHONE! <<<<<<<<<<<<<
NOW:
-Lets consider that you have downloadet the firmware
1. Unpack ROM, and Click on Flash_tool.exe
2. Select a the MT6589_Android_scatter_emmc.txt in ROM from target_bin folder
3. Wait file to be added into Flash Tool
4. Choose Options->USB Model,click USB Model SKIP THIS STEP IFF SELECTED
5. Choose Option->DA DownLoad All->Speed->High Speed, click High Speed
6. Check box with DA DL All With Check Sum
7. Turn off your phone - skip this step is allready powered off
8. "Press Firmware->Upgrade "
9. And ONLY NOW connect your phone into the computer via USB data cable.
10. The process will start and a red progress bar will appear after color purple, yellow.
OR
11. If the step 9 dont work open the case of your phone and you will find a red small buton and press it 2 seconds.
12. The process will start and a red progress bar will appear after color purple, yellow.
13. And green circles display
- Finish !
- You can now safely disconnect your phone and turn it on!
After this tell me iff something goes wrong !
stympy said:
Hi.
Do not panic. Your phone is just soft bricked.
Here is the link to download what you must flash first:
https://drive.google.com/folderview?id=0B2ORIgaV4iacT01mTm5JVzFuRGs&usp=sharing
And now here's a little tutorial how to save your phone. You should respectit exactly.
Step by step you will do this:
>>>>> USE WINDOWS 7 FOR THIS TUTORIAL <<<<<<<<<<<
>>>>>>>>>>REMOVE THE USB CALBLE FROM PHONE! <<<<<<<<<<<<<
NOW:
-Lets consider that you have downloadet the firmware
1. Unpack ROM, and Click on Flash_tool.exe
2. Select a the MT6589_Android_scatter_emmc.txt in ROM from target_bin folder
3. Wait file to be added into Flash Tool
4. Choose Options->USB Model,click USB Model SKIP THIS STEP IFF SELECTED
5. Choose Option->DA DownLoad All->Speed->High Speed, click High Speed
6. Check box with DA DL All With Check Sum
7. Turn off your phone - skip this step is allready powered off
8. "Press Firmware->Upgrade "
9. And ONLY NOW connect your phone into the computer via USB data cable.
10. The process will start and a red progress bar will appear after color purple, yellow.
OR
11. If the step 9 dont work open the case of your phone and you will find a red small buton and press it 2 seconds.
12. The process will start and a red progress bar will appear after color purple, yellow.
13. And green circles display
- Finish !
- You can now safely disconnect your phone and turn it on!
After this tell me iff something goes wrong !
Click to expand...
Click to collapse
Thanks for replying But my phone cant connect to computer... My computer keep saying my phone is malfunction...
tngultimate said:
Thanks for replying But my phone cant connect to computer... My computer keep saying my phone is malfunction...
Click to expand...
Click to collapse
Can you tel me what your computer says more exacly ?
Hi...
from mr stympy thread...
stympy said:
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip or SuperSU on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119 or SP_Flash_Tool_v5.1352.01. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
10.1. I have updated the post with some custom scatter files for 4GB and 8GB Firmware. Iff you get diferent errors when you flash the recovery file use this custom scatter files.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Then boot directly to recovery your phone by pressing power with vol + and vol - butons together. Not Optional!
15. From TWRP flash Superuser.zip or SuperSU 2.45. SuperSU is fixed. Works fine now.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Click to expand...
Click to collapse
item no.1: don't know if it installed correctly, but i can copy the superuser.zip unto my sdcard
item no.6: using spflash tools ver. v3.1344.0.212 that mr stympy personally gave me...
at item no.12 : 100% completed but no green circle appeared....:crying:
snapshot : imgur.com/6OCfkwM
my phone is still connected to the pc and sp flash tool because afraid of bricking it....:crying: please help:crying:
blkxiicat said:
Hi...
from mr stympy thread...
item no.1: don't know if it installed correctly, but i can copy the superuser.zip unto my sdcard
item no.6: using spflash tools ver. v3.1344.0.212 that mr stympy personally gave me...
at item no.12 : 100% completed but no green circle appeared....:crying:
snapshot : imgur.com/6OCfkwM
my phone is still connected to the pc and sp flash tool because afraid of bricking it....:crying: please help:crying:
Click to expand...
Click to collapse
Disconnect your phone and if is not starting press the small red button for 20 secconds.
Keep me informed!
stympy said:
Disconnect your phone and if is not starting press the small red button for 20 secconds.
Keep me informed!
Click to expand...
Click to collapse
ok, managed to boot the phone, but when got to home screen it says that my date is wrong....(1/1/2010).
auto-sync with network time....my date and time is back to normal...
shut down the phone (i didn't press the red button) and try to reboot into recovery (power+volumeup+volumedown)
............no twrp, i think (maybe stock recovery mode... some china word with android mascot as background...)
fortunately my phone was not bricked... but no twrp either.....so what is the problem..
thanks.
blkxiicat said:
ok, managed to boot the phone, but when got to home screen it says that my date is wrong....(1/1/2010).
auto-sync with network time....my date and time is back to normal...
shut down the phone (i didn't press the red button) and try to reboot into recovery (power+volumeup+volumedown)
............no twrp, i think (maybe stock recovery mode... some china word with android mascot as background...)
fortunately my phone was not bricked... but no twrp either.....so what is the problem..
thanks.
Click to expand...
Click to collapse
Use version 5 of TWRP!
stympy said:
Use version 5 of TWRP!
Click to expand...
Click to collapse
hmm....
stympy said:
Originally Posted by stympy
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip or SuperSU on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119 or SP_Flash_Tool_v5.1352.01. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
10.1. I have updated the post with some custom scatter files for 4GB and 8GB Firmware. Iff you get diferent errors when you flash the recovery file use this custom scatter files.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
Click to expand...
Click to collapse
point no.10 does not appear in ver. 5 sp flash tools....is it okay?
blkxiicat said:
hmm....
point no.10 does not appear in ver. 5 sp flash tools....is it okay?
Click to expand...
Click to collapse
In version 5 it automaticaly selected, to avoid any mistake.
Hi.
I wrote problems with my wife's P9000 here: https://forum.xda-developers.com/showpost.php?p=72990392&postcount=14
And yes: no solution works. And either there is no stock recovery or this device can't find them.
I offer 50 Euro for help. My goal: to install custom recovery (most TWRP), install custom ROM (some stable version of Marshmallow) and root it.
I tried about 6 hours and I have had enough.
Except that I will be appreciate.
German? English?
Vielleicht kann ich helfen
One of the official ota p9000 updates has a corrupt recovery. This is why you can't get into the recovery and why the official update fails all the time. (I think).
About the flashing part with sp flashtools. You need to install those mtk drivers with the driver signature turned off in Windows. Otherwise those drivers can not be installed on you pc and flashing your phone can't be done. Just search Google for how to disable driver signature for your Windows version.
About the part of making a scatter file. You do not need to make a scatter file. It is included in Roms that have a scatter file with them (the roms that are ment to be flashed with sp flashtools).
If you want to flash a custom recovery with sp flashtools. You load the scatter file of a stock ROM and make sure, in the download screen of sp flashtools, the location points to the custom recovery .img file. And make sure there is a check mark on the left of the row for the recovery. Otherwise sp flashtools will simply skip that part with flashing.
If you want to install a custom ROM without spflashtool. You need a custom recovery and flash it via the recovery.
I hope I helped you enough. Because this how it works for me every time on every mtk phone (that I owned). I do not want your €50
MoRiA Cheo said:
Hi.
I wrote problems with my wife's P9000 here: https://forum.xda-developers.com/showpost.php?p=72990392&postcount=14
And yes: no solution works. And either there is no stock recovery or this device can't find them.
I offer 50 Euro for help. My goal: to install custom recovery (most TWRP), install custom ROM (some stable version of Marshmallow) and root it.
I tried about 6 hours and I have had enough.
Except that I will be appreciate.
Click to expand...
Click to collapse
Do you have somewhere easier to talk? whatsapp? my whatsapp is +351 910012132 i can help
MasterDK2015 said:
German? English?
Vielleicht kann ich helfen
Click to expand...
Click to collapse
Polish or english. ?
MoRiA Cheo said:
Polish or english. ?
Click to expand...
Click to collapse
Hi, Just a couple of questions.
When did you get the P9000?
What version of Windows?
Things to download
I recommend you install the 20170112 (store on computer)here
Extract the RAR file, it is contained in a folder, no need to extract in a new folder.
Super SU root (store on phone, SD card preferred) here
And TWRP 3.0.2-8 from Jonny (store on computer)here
Go to Device Manager.
View - Show Hidden Devices
If you see MTK Preloader VCOM
or MTK USB Device, that's good. More MTK xxxxx the better.
Open SP Flash Tool
Load the scatter file from the load button. 3rd row down. Go to the Extracted RAR file and select MT6755_Scatter.txt.
Then press the recovery file location name (C: USER ........ recovery.img) and navigate to the
TWRP 3.0.2-8.img and select that.
Now Press the Download (green down arrow) button and then use the stock cable and connect to a USB 2.0 port, then while pressing the volume up button, on the P9000, connect the phone to the other end of the cable.
A Red bar down the bottom saying Download DA 100% should appear and then a yellow bar and some percentage, which will take 5 or so minutes to go all yellow then a big green tick on a pop up should appear and it's done!
Then go to recovery which is Volume Up and Power at the same time untill the ELE logo appears. When it appears release the buttons. Swipe the allow modifications and then press the install button, navigate to the SuperSu.zip by Select storage if you have an SD CARD, otherwise it will probably be in the Download folder. Swipe to install, wipe cache and dalvik, swipe and reboot system. Hope that works any questions just ask. Sincerely, X
Hexyl said:
One of the official ota p9000 updates has a corrupt recovery. This is why you can't get into the recovery and why the official update fails all the time. (I think).
About the flashing part with sp flashtools. You need to install those mtk drivers with the driver signature turned off in Windows. Otherwise those drivers can not be installed on you pc and flashing your phone can't be done. Just search Google for how to disable driver signature for your Windows version.
About the part of making a scatter file. You do not need to make a scatter file. It is included in Roms that have a scatter file with them (the roms that are ment to be flashed with sp flashtools).
If you want to flash a custom recovery with sp flashtools. You load the scatter file of a stock ROM and make sure, in the download screen of sp flashtools, the location points to the custom recovery .img file. And make sure there is a check mark on the left of the row for the recovery. Otherwise sp flashtools will simply skip that part with flashing.
If you want to install a custom ROM without spflashtool. You need a custom recovery and flash it via the recovery.
I hope I helped you enough. Because this how it works for me every time on every mtk phone (that I owned). I do not want your €50
Click to expand...
Click to collapse
Your instructions was very, very good but a little bit general for me. I lost myself in Your shortcuts (device on/off, connected/disconnected). But when I finished, I see You wrote everything.
So thank You very much. You helped me very much, You showed me the instruction I didn't find before.
Ninja X said:
Hi, Just a couple of questions.
When did you get the P9000?
What version of Windows?
Things to download
I recommend you install the 20170112 (store on computer)here
Extract the RAR file, it is contained in a folder, no need to extract in a new folder.
Super SU root (store on phone, SD card preferred) here
And TWRP 3.0.2-8 from Jonny (store on computer)here
Go to Device Manager.
View - Show Hidden Devices
If you see MTK Preloader VCOM
or MTK USB Device, that's good. More MTK xxxxx the better.
Open SP Flash Tool
Load the scatter file from the load button. 3rd row down. Go to the Extracted RAR file and select MT6755_Scatter.txt.
Then press the recovery file location name (C: USER ........ recovery.img) and navigate to the
TWRP 3.0.2-8.img and select that.
Now Press the Download (green down arrow) button and then use the stock cable and connect to a USB 2.0 port, then while pressing the volume up button, on the P9000, connect the phone to the other end of the cable.
A Red bar down the bottom saying Download DA 100% should appear and then a yellow bar and some percentage, which will take 5 or so minutes to go all yellow then a big green tick on a pop up should appear and it's done!
Then go to recovery which is Volume Up and Power at the same time untill the ELE logo appears. When it appears release the buttons. Swipe the allow modifications and then press the install button, navigate to the SuperSu.zip by Select storage if you have an SD CARD, otherwise it will probably be in the Download folder. Swipe to install, wipe cache and dalvik, swipe and reboot system. Hope that works any questions just ask. Sincerely, X
Click to expand...
Click to collapse
You are the NINJA!
Thank You! Thanks to You I installed TWRP. Rest is easier.
You show me to install ANY MTK device and P9000 can be on. And You show me precisely that I should change the destination point for TWRP (so not default but the .img file).
And that was important for me. And thanks to You I did it.
Thank You.
Please write to me in private message Your account number or PayPal.
Thank You again.
MoRiA Cheo said:
You are the NINJA!
Thank You! Thanks to You I installed TWRP. Rest is easier.
You show me to install ANY MTK device and P9000 can be on. And You show me precisely that I should change the destination point for TWRP (so not default but the .img file).
And that was important for me. And thanks to You I did it.
Thank You.
Please write to me in private message Your account number or PayPal.
Thank You again.
Click to expand...
Click to collapse
No problem. I'll PM my PayPal soon. Thanks!
i had try to find the twrp file for lyf water 7s but i did'nt get i search ..unable to find can anyine tell me plzz how to root lyf water 7s without pc its too hard i use all app or tell root through pc but safe way
Hey Guys,There is a Good News for you all After a long time i have found The way on how to root our phone LYF Water 7s Ls5507{yup you read it right} ? I have ported a TWRP Custom recovery for it [ I know its very long time since no development has been done for our very own device but wait is over now ! ]
Procedure to flash TWRP Recovery and Root
------------------------------------------------------------------------
Follow These Steps:-
1>Download The required Tools pack for flashing the recovery From here-https://drive.google.com/file/d/1Dnq6DwJdLI3lYyLQzgUG3Y_u024EiWEd/view?usp=drivesdk And Super Su v2.82 From here-https://drive.google.com/file/d/1jMjCziMaafiyo3_b0GVlaDZEy1RB1fbb/view?usp=drivesdk
2>Install the MTK drivers for your phone in your Computer (search the Google)
3>Extract the tools pack on your computer and copy the Super Su v2.82.zip to your phone's SD Card
4>And After Extracting tools pack you will get 2 folders Twrp Recovery pack and SP Flash Tool
5>Open SP Flash Tool Folder,Double click Flash Tool.exe
6>Now in SP Flash Tool Click on Scatter Loading Button
7>Now Locate the folder where you have extracted the "Twrp Flashing Pack" Folder open it and select Mtk6753 Android Scatter.txt and click open
8>From the List Choose Recovery and hot the Download Button Above
9>After Clicking "Download" Completely Power off your phone and Connect your phone to Computer using USB Cable and the Tool will start flashing the Recovery image in it
10>After the Flashing Process Completes You will be able to see a green ring,now disconnect the cable and press and hold volume up(+) and power button ,you will see very small words according to them locate recovery option using volume up(+)key and select it using volume down(-)key then after some time the recovery will open.
11>In the recovery draw your pattern or enter your password(if asked)and swipe the bar ,then go to Your sdcard location where you have placed the Super Su v2.82.zip then flash it and reboot your phone(at first boot it may restart 2 times but dont worry its preparing the phone)and when your phone boots up........ Congratulations you have rooted your device successfully !
-------------------------------------------------------------------------
If you liked my work please let me know
Thank you !
Also i will keep updating you all about the latest mods and hacks for the device and for now i m trying to port miui 9 for the device !
So stay tuned !