Related
FLASHING CUSTOM RECOVERY (CWM) FROM LGMDP
FOR LG P500 / OPTIMUS ONE ONLY
This method works for all unrooted p500/optimus one and p500/optimus one devices stuck in emergency mode.
DO THIS ON YOUR OWN RISK, I WILL HAVE NO LIABILITY IF YOU BRICK YOUR PHONE !!!
download lgmdp : Download here
download clockwork recovery (5.0.2.0): Download here
1. disable lg modem ( in device manager->modems)
2. now connect your phone to pc. (If phone not booting into rom connect in emergency mode, turn off phone and press (volup+return+power) buttons simultaneously)
3. start lgdmp
4. click "select port"
Phone will be automatically detected press "connect"
(close the pop up window of image select generally you will get it on connect of lgmdp)
5. backup nv for safety (tools->nv backup) {ignore this step when phone connected in emergency mode, i did ignore this and found no risk of loosing nv}
6. extract downloaded recovery into a new folder
7. select the extracted recovery folder as "image folder or select image" in lgmdp
(it gives some errors as other files are not present, donot worry as we are only flashing recovery those 2 files are enough, files "recovery" and "partiton" will be automatically checked and others gray out)
8. Close the selection window and press "download" (in main window of lgmdp)
DONOT DISCONNECT YOUR MOBILE UNTILL IT SHOWS DOWNLOAD COMPLETE AT BOTTOM
it shows in middle trying to connect to phone etc. donot touch the phone it will be automatically connect everytime.
AFTER DOWNLOAD COMPLETE your device should boot into recovery
1. switch off your device
2. pressing (home+vol down+power) buttons simultaneously should boot into recovery.
now install whichever rom you want and enjoy
Tested on O1 having baseband v10 and v20 also, from normal boot and emergency mode as well and it works.
mak.3736 said:
FOR LG P500 / OPTIMUS ONE ONLY
This method should work for all unrooted devices and p500/optimus one devices stuck in emergency mode.
This is tested on O1 having v10 baseband and it works.
SHOULD WORK FOR V20 as well
download lgmdp : http://www.mediafire.com/?ov799yg7vbnce9j
download cwm recovery : http://www.mediafire.com/?1lcjbfa3ypqbqj3
1. disable lg modem ( in device manager->modems)
2. now connect your phone to pc.(if phone not booting into rom connect in emergency mode (home+volup+return) button holding simultaneously)
3. start lgdmp
4. click "select port"
Phone will be automatically detected press "connect"
(close the pop up window of image select generally you will get it on connect of lgmdp)
5. backup nv for safety (tools->nv backup) {ignore this step while connecting phone in emergency mode, i did ignore this and found no risk of loosing nv}
6. extract downloaded recovery into a new folder
7. select the extracted recovery folder as "image folder or image select" in lgmdp
(it gives some errors donot worry, but files "recovery" and "partiton" will be automatically checked and others gray out)
8. press start or download
DONOT DISCONNECT YOUR MOBILE UNTILL IT SHOWS DOWNLOAD COMPLETE AT BOTTOM
AFTER DOWNLOAD COMPLETE your device should boot into recovery
1. switch off your device
2. pressing (home+vol down+power) buttons simultaneously should boot into recovery.
now install whichever rom you want and enjoy
TESTED ON v10 baseband LG O1 and it worked for me.
Click to expand...
Click to collapse
i need to try it once.thanks tho
phone is not detecting
no phone to connect.LGMDP-v1.5 is not detecting the phone.pls help...my full problem http://forum.xda-developers.com/showthread.php?p=19303459#post19303459
ojobinv said:
no phone to connect.LGMDP-v1.5 is not detecting the phone.pls help...my full problem http://forum.xda-developers.com/showthread.php?p=19303459#post19303459
Click to expand...
Click to collapse
reinstall drivers.
let your phone be on (stuck at lg logo), connect to computer, flash custom recovery from lgmdp.
There might errors occur at nv backup or nv restore but it will flash recovery.
my phone doesnt even starting in emergency mode.
1. disable lg modem ( in device manager->modems)
2. now connect your phone to pc. (If phone not booting into rom connect in emergency mode, turn off phone and press (home+volup+return) buttons simultaneously)
3. start lgdmp
4. click "select port"
Phone will be automatically detected press "connect"
(close the pop up window of image select generally you will get it on connect of lgmdp)
5. backup nv for safety (tools->nv backup) {ignore this step when phone connected in emergency mode, i did ignore this and found no risk of loosing nv}
6. extract downloaded recovery into a new folder
7. select the extracted recovery folder as "image folder or select image" in lgmdp
(it gives some errors as other files are not present, donot worry as we are only flashing recovery those 2 files are enough, files "recovery" and "partiton" will be automatically checked and others gray out)
8. press start or download
DONOT DISCONNECT YOUR MOBILE UNTILL IT SHOWS DOWNLOAD COMPLETE AT BOTTOM
AFTER DOWNLOAD COMPLETE your device should boot into recovery
1. switch off your device
2. pressing (home+vol down+power) buttons simultaneously should boot into recovery.
now install whichever rom you want and enjoy
Tested on O1 having baseband v10 and v20 also, from normal boot and emergency mode as well and it works.[/QUOTE]
hi
i tried to update firmware through kdz updater.
it erased the c drive but then due to some error my phone is not starting even in emergency mode.
i tried all possible combinations of hard keys.
luckily its under warranty.
but i dont know any convincing reason that the service center would accept.
plz help.
farzii said:
hi
i tried to update firmware through kdz updater.
it erased the c drive but then due to some error my phone is not starting even in emergency mode.
i tried all possible combinations of hard keys.
luckily its under warranty.
but i dont know any convincing reason that the service center would accept.
plz help.
Click to expand...
Click to collapse
Tell them you were updating phone through official lg tool software updater, the phone went to emergency mode during process, it shutdown and it didnt power on since then.
They wont ask a single question after this. All the best
(I did use the same explanation)
Heyy, so when I do this(note I am stuck in recovery mode on the phone), it says Error can't open serial port, reboot and restart. Every time I click download to put the recovery in it it does this.
MXFrodo195 said:
Heyy, so when I do this(note I am stuck in recovery mode on the phone), it says Error can't open serial port, reboot and restart. Every time I click download to put the recovery in it it does this.
Click to expand...
Click to collapse
i experienced same problem in one of my friends computer, but then it was solved when we tried again after fresh install of windows and drivers, better you try on any other computer, i m sure u will get it work.
mak.3736 said:
i experienced same problem in one of my friends computer, but then it was solved when we tried again after fresh install of windows and drivers, better you try on any other computer, i m sure u will get it work.
Click to expand...
Click to collapse
I tried from another computer, it's doing the same exact thing. Any other ideas?
Thats what happens when I click download, when I click Select Image, nothing is happening at all. In recovery should I be mounting anything?(data, sdcard, cache, system). Or should I be mounting the USB Storage? I am just baffled, I must be doing something simple wrong, as it seems pretty straightforward.
Hi,
Thank you for the informations.
after image file selected and started, error message was occured "Error! Partition table"
Plz help...
solenun said:
Hi,
Thank you for the informations.
after image file selected and started, error message was occured "Error! Partition table"
Plz help...
Click to expand...
Click to collapse
I think you are not selecting partion.mbn, download the recovery zip once again and follow below:
there are 2 files in zip, recovery image and other is partition.mbn.
Make sure both the files are selected and ticked while image select.
partition.mbn will be selected in partition table,
recovery.img will be selected in recovery image,
then close the window of image select and press download.
MXFrodo195 said:
I tried from another computer, it's doing the same exact thing. Any other ideas?
Thats what happens when I click download, when I click Select Image, nothing is happening at all. In recovery should I be mounting anything?(data, sdcard, cache, system). Or should I be mounting the USB Storage? I am just baffled, I must be doing something simple wrong, as it seems pretty straightforward.
Click to expand...
Click to collapse
uninstall other phone drivers (nokia , motorola etc.) from computer, reboot, reinstall lg p500 usb drivers, reboot and follow guide as the same.
mak.3736 said:
uninstall other phone drivers (nokia , motorola etc.) from computer, reboot, reinstall lg p500 usb drivers, reboot and follow guide as the same.
Click to expand...
Click to collapse
Don't forget to disable the LGE virtuial modem with tools in the LGDMP after it "sees" the phone(leaving the other LGE modem active) (that is the LGDMP)Also after the disable cmd do not restart your computer(mine suggestes this after).Select your image zip the p500 partition table is included there.You will get about 4 or 5 error windows just ok click them away (ignore) and run download.It takes a short time and then pauses a min. and continues.DO NOT disconnect or stop/cancell anything untill you get a red DOWNLOAD COMPLETE!..I used this a couple of times and feel it a very safe way to flash
is it possible to flash amon ra recovery via LGMDP.exe?
if so, how?
vivithbharath said:
is it possible to flash amon ra recovery via LGMDP.exe?
if so, how?
Click to expand...
Click to collapse
yes , but i didnt test it.
try it by replacing clockwork's recovery.img with amonra's revovey.img in folder u get after extracting the zip of clockwork provided in thread.
(i mean use partition.mbn from clockwork zip in thread and amonra recovery.img and flash with lgmdp)
mak.3736 said:
yes , but i didnt test it.
try it by replacing clockwork's recovery.img with amonra's revovey.img in folder u get after extracting the zip of clockwork provided in thread.
(i mean use partition.mbn from clockwork zip in thread and amonra recovery.img and flash with lgmdp)
Click to expand...
Click to collapse
thanks! will try and post the results
My start button is greyed out, clicking it is useless.
Edit: after selecting the file, I closed the window and clicked download. After backing up my NV, the flash worked.
jasonwsc said:
My start button is greyed out, clicking it is useless.
Edit: after selecting the file, I closed the window and clicked download. After backing up my NV, the flash worked.
Click to expand...
Click to collapse
yes i mentioned in procedure press "start" or "download", its obvious start button will be grayed out as all files are not selected. so close file select window and press "download" in main window..
............
I have added it in steps as well now
Why is it that after I selected the port, the select image button is not doing anything? it's clickable but it does nothing?
bryanposas said:
Why is it that after I selected the port, the select image button is not doing anything? it's clickable but it does nothing?
Click to expand...
Click to collapse
After selecting port , a window will pop up to browse for "image folder" close this poped up window then all the functions of main window of lgmdp will be accesible
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser or SuperSU at least 2.16, no less.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip or SuperSU on your SDCARD. Remember: only one is good. DO NOT FLASH BOTH. Flash the one you like.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 or the newest one TWRP 2.8.4.0 rev 2 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119 or SP_Flash_Tool_v5.1352.01. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum in SP Flash Tool v3. In SP Flash Tool v 5 dont need. They are allready selected. Recovery.img should appear checked.
10.1. I have updated the post with some custom scatter files for 4GB and 8GB Firmware. Iff you get diferent errors when you flash the recovery file use this custom scatter files.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Then boot directly to recovery your phone by pressing power with vol + and vol - butons together. Not Optional!
15. From TWRP flash Superuser.zip or SuperSU 2.xx. SuperSU is fixed. Works fine now.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback.
Update:
I have uploaded TWRP Corrected by Javum. Thanks Javum. And it is working on ROW 226 and 227 tested personaly by installing patches, superuser and making backups.
Sent from my Lenovo P780
SP Flash Tool_v.3 and v.5
stympy said:
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have the latest FlashTool.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
Click to expand...
Click to collapse
This method did not work i got this error
"pmt changed for the rom it must be downloaded"
astrokid1993 said:
This method did not work i got this error
"pmt changed for the rom it must be downloaded"
Click to expand...
Click to collapse
Try to use Firmware Upgrade buton.
Or: You need to edit the file MT6589_Android_scatter_emmc.txt section USRDATA 0x48d80000 on USRDATA 0x58980000.
Waiting for feedback.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Point no 12 doesn't work with me, Anything I should know?
asambe2dumb said:
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Point no 12 doesn't work with me, Anything I should know?
Click to expand...
Click to collapse
If the 12 point doesn't work it means that you don't have the driver installed or installed correctly. Check the drivers.
Sent from my Lenovo P780 using XDA Free mobile app
all steps are done but not succsses
Hallo... IN my lenovo p780 with officaly updated android 4.4.2 and not rooted phone .I fallow all steps carrectly as u discribed after press download button when I connect my switched off phone I got mtp error than I edit scatter file user data as describe in comment section after that I press download and connect my p780 switched of all process done smuthaly I got green circles that's mean I am done after that I switched on phone and switched off phone for boot in recovery I press vol+ vol- and power buttons but their is not twrp recovery option ..only stock recovery option .
Pls help bro ...what I am doing wrong?. Or any other way to do this ?
Thanks for this wonderful tutorial.
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder  )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback. 
Update:
I have uploadet TWRP Corrected by Javum. Thanks Javum. And it is working on ROW 221 tested personaly by installing patches, superuser and making backups.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
Sent from my Lenovo P780 using XDA Free mobile app
I have not rooted lenovo p780 official updated to android 4.4.2 s221 OK I want root my phone I try every thing like pharma root. One click root ;rescue root;vroot ;kingoroot;and many other which I don't remember but not success ..OK than I try to follow your method ...first when I connect my switched off phone downloading process start after red bar complete I got mtp error
Then I edit scatter file user data section as u mansion in comments sections after that download has done withouts error I got green circle that's mean I am done ... OK I disconnect phone from computer and power on than switched off for boot in recovery ... I press power button + vol up and down together but their is ...
NOT TWRP RECOVERY .. only stock android recovery huuh what I do now ..where I am wrong any suggestion plz help
And thanks for this wonder full tutorial.
pu04 said:
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder  )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback. 
Update:
I have uploadet TWRP Corrected by Javum. Thanks Javum. And it is working on ROW 221 tested personaly by installing patches, superuser and making backups.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
Sent from my Lenovo P780 using XDA Free mobile app
I have not rooted lenovo p780 official updated to android 4.4.2 s221 OK I want root my phone I try every thing like pharma root. One click root ;rescue root;vroot ;kingoroot;and many other which I don't remember but not success ..OK than I try to follow your method ...first when I connect my switched off phone downloading process start after red bar complete I got mtp error
Then I edit scatter file user data section as u mansion in comments sections after that download has done withouts error I got green circle that's mean I am done ... OK I disconnect phone from computer and power on than switched off for boot in recovery ... I press power button + vol up and down together but their is ...
NOT TWRP RECOVERY .. only stock android recovery huuh what I do now ..where I am wrong any suggestion plz help
And thanks for this wonder full tutorial.
Click to expand...
Click to collapse
By any chance is your phone made in 2014 ?
Then if it is use preloader. Check preloader and try this one.
Its one year old phone ..with jelly bin 4.2.2 now I updated to 4.4.4 originally by ota ..I want to root it actually in mtk toot its show this massage `` ATTENTION! File /system/recovery-from-boot.p which restore factory recovery in case of phone switching on in a normal mode Is Found!
I don't know but I think its affect ..can u pls explain it what's this mean.
Thanks for reply ...I try with bootloder next day
Sent from my Lenovo P780 using XDA Free mobile app
Will it work on S214 also or should i instal S221 for my phone
astrokid1993 said:
Will it work on S214 also or should i instal S221 for my phone
Click to expand...
Click to collapse
For me worked on both.
Sent from my Lenovo P780
Thanksgiving
OK....FIRST I HEARTILY THANKS TO U ..NOW I AM SUCCESS ..finally rooted my lenovo p780 4.4.2 KitKat updated phone ..without any error or bricking my phone .. Thanks for this wonder full tutorial ..
As I mentioned previous reply that I got error from Sp flash tool ..something pmt error ..than as u sugest i edit user data section in scatter data section and flash it ..but nothing happen their is only stock recovery .. Today i retry process ..
1- follow all steps as it is
2 - for pmt error change user data section 3- at last u advise that power on phone then reboot in recovery by pressing volume+'- +power button at this stage ..what I have done ..is
I don't on my phone ..after flashing recovery I direct go to recovery using power + volume up+ volume down ..and waaaala here is done I got twrp custom recovery .. But don't flase superuser .zip just shutdown phone and on go to normal mode and check every thing is fine ..now power off go to recovery ...there is twrp present ..in recovery install super user ..just unchake verify check mark its install without any error ..and ..GOT ROOTED ..
Conclusion - why I unsuccessful in first time I don't know but think..I have this type of file .. File /system/recovery-from-boot.p which restore factory recovery in case of phone switching on in a normal mode Is Found! I think its prevent twrp when I normally switch on phone ..so this time I don't on phone go to direct recovery and all is done .. I got custom recovery..
AT last I thank you again for this great tut. Its worked for me finally .
Sent from my Lenovo P780 using XDA Free mobile app
stympy said:
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback.
Update:
I have uploadet TWRP Corrected by Javum. Thanks Javum. And it is working on ROW 221 tested personaly by installing patches, superuser and making backups.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
Click to expand...
Click to collapse
Friend, first time I follow all your steps to install TWRP , but it failed . And I see your reply in this thread and change the USR DATA . But it failed again , MY PHONE WAS BRICKED !!!!! IT DONT DO ANY RESPONSE , CANT POWER ON , CANT CONNECT TO COMPUTER , CANT GO TO RECOVERY . IT ONLY SHOW A RED LIGHT WHEN CHARGING . HOW TO SOLVE THIS PROBLEM ??? PLEASE HELP ME ...
stympy said:
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback.
Update:
I have uploadet TWRP Corrected by Javum. Thanks Javum. And it is working on ROW 221 tested personaly by installing patches, superuser and making backups.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
Click to expand...
Click to collapse
Not working at all for me i did everything correctly till point 11 when i connect my phone as in point 12 my phone starts charging and nothing is getting detected in the sp flash tool.
Any one please help me with my problem
tngultimate said:
Friend, first time I follow all your steps to install TWRP , but it failed . And I see your reply in this thread and change the USR DATA . But it failed again , MY PHONE WAS BRICKED !!!!! IT DONT DO ANY RESPONSE , CANT POWER ON , CANT CONNECT TO COMPUTER , CANT GO TO RECOVERY . IT ONLY SHOW A RED LIGHT WHEN CHARGING . HOW TO SOLVE THIS PROBLEM ??? PLEASE HELP ME ...
Click to expand...
Click to collapse
Your phone seems to be produced in 2014. For this phones must do this:
1. Must flash with another preloader.
Look for this ROM : P780_S136_140306_Lang.7z
Flash this Rom then OTA update.
Then tell me if it works.
Sent from my Lenovo P780
astrokid1993 said:
Not working at all for me i did everything correctly till point 11 when i connect my phone as in point 12 my phone starts charging and nothing is getting detected in the sp flash tool.
Any one please help me with my problem
Click to expand...
Click to collapse
Did you installed the drivers?
Did you presed the firmware upgrade first and then plugged the phone?
Update
Try this:
Press Download and open the case of your phone and press the little red buton for 2 seconds.
Sent from my Lenovo P780
stympy said:
Did you installed the drivers?
Did you presed the firmware upgrade first and them plugged the phone?
Sent from my Lenovo P780
Click to expand...
Click to collapse
I installed driver already... My phone now cant do anything... Help me please ...
tngultimate said:
I installed driver already... My phone now cant do anything... Help me please ...
Click to expand...
Click to collapse
Hi.
Do not panic. Your phone is just soft bricked.
Here is the link to download what you must flash first:
https://drive.google.com/folderview?id=0B2ORIgaV4iacT01mTm5JVzFuRGs&usp=sharing
And now here's a little tutorial how to save your phone. You should respectit exactly.
Step by step you will do this:
>>>>> USE WINDOWS 7 FOR THIS TUTORIAL <<<<<<<<<<<
>>>>>>>>>>REMOVE THE USB CALBLE FROM PHONE! <<<<<<<<<<<<<
NOW:
-Lets consider that you have downloadet the firmware
1. Unpack ROM, and Click on Flash_tool.exe
2. Select a the MT6589_Android_scatter_emmc.txt in ROM from target_bin folder
3. Wait file to be added into Flash Tool
4. Choose Options->USB Model,click USB Model SKIP THIS STEP IFF SELECTED
5. Choose Option->DA DownLoad All->Speed->High Speed, click High Speed
6. Check box with DA DL All With Check Sum
7. Turn off your phone - skip this step is allready powered off
8. "Press Firmware->Upgrade "
9. And ONLY NOW connect your phone into the computer via USB data cable.
10. The process will start and a red progress bar will appear after color purple, yellow.
OR
11. If the step 9 dont work open the case of your phone and you will find a red small buton and press it 2 seconds.
12. The process will start and a red progress bar will appear after color purple, yellow.
13. And green circles display
- Finish !
- You can now safely disconnect your phone and turn it on!
After this tell me iff something goes wrong !
stympy said:
Hi.
Do not panic. Your phone is just soft bricked.
Here is the link to download what you must flash first:
https://drive.google.com/folderview?id=0B2ORIgaV4iacT01mTm5JVzFuRGs&usp=sharing
And now here's a little tutorial how to save your phone. You should respectit exactly.
Step by step you will do this:
>>>>> USE WINDOWS 7 FOR THIS TUTORIAL <<<<<<<<<<<
>>>>>>>>>>REMOVE THE USB CALBLE FROM PHONE! <<<<<<<<<<<<<
NOW:
-Lets consider that you have downloadet the firmware
1. Unpack ROM, and Click on Flash_tool.exe
2. Select a the MT6589_Android_scatter_emmc.txt in ROM from target_bin folder
3. Wait file to be added into Flash Tool
4. Choose Options->USB Model,click USB Model SKIP THIS STEP IFF SELECTED
5. Choose Option->DA DownLoad All->Speed->High Speed, click High Speed
6. Check box with DA DL All With Check Sum
7. Turn off your phone - skip this step is allready powered off
8. "Press Firmware->Upgrade "
9. And ONLY NOW connect your phone into the computer via USB data cable.
10. The process will start and a red progress bar will appear after color purple, yellow.
OR
11. If the step 9 dont work open the case of your phone and you will find a red small buton and press it 2 seconds.
12. The process will start and a red progress bar will appear after color purple, yellow.
13. And green circles display
- Finish !
- You can now safely disconnect your phone and turn it on!
After this tell me iff something goes wrong !
Click to expand...
Click to collapse
Thanks for replying But my phone cant connect to computer... My computer keep saying my phone is malfunction...
tngultimate said:
Thanks for replying But my phone cant connect to computer... My computer keep saying my phone is malfunction...
Click to expand...
Click to collapse
Can you tel me what your computer says more exacly ?
Hi all ,
i'm new.
I have a rooted p4502 (op3ndott)
specs
mtk 6582
1 gb ram
I accidentally deleted the folder "framework" in system partition. The phone crash and when i start it go in boot loop.
i can go in recovery and also i do a data/factory reset, and always boot loop.
i havent did a backup of rom and now i can find the original rom on the web.
What i can do ? it's recuperable ?
(sorry for my english but i'm italian )
please answer
i have same problem :crying:
You must install CWM or TWRP with spflashtool. I install twrp in terminal, I don't now method install it with spflashtool, you must looking in network. I can upload twrp and backup firmware ver 208 and ver 213.
------
1. Install MediaTek DA USB VCOM drivers
2. Download and run SPFlashTool
3. Click Scatter-loading button to load the correct scatter file
4. Deselect all parts except recovery.img, set path to recovery.img
5. Turn off your phone, remove the battery and replace it after some seconds (and don't turn on the phone).
6. Press Download and connect your phone into the computer via USB data cable.
7. The process will start and a red progress bar will appear.After the red progress bar is complete, there will appear a purple progress bar.When the yellow bar is complete, you'll get a popup with a green circle and Download OK message,
which means that the process has been successfully terminated.
If you have installed recovery you can install backup. I can upload my backup.
shanti77 said:
You must install CWM or TWRP with spflashtool. I install twrp in terminal, I don't now method install it with spflashtool, you must looking in network. I can upload twrp and backup firmware ver 208 and ver 213.
------
1. Install MediaTek DA USB VCOM drivers
2. Download and run SPFlashTool
3. Click Scatter-loading button to load the correct scatter file
4. Deselect all parts except recovery.img, set path to recovery.img
5. Turn off your phone, remove the battery and replace it after some seconds (and don't turn on the phone).
6. Press Download and connect your phone into the computer via USB data cable.
7. The process will start and a red progress bar will appear.After the red progress bar is complete, there will appear a purple progress bar.When the yellow bar is complete, you'll get a popup with a green circle and Download OK message,
which means that the process has been successfully terminated.
If you have installed recovery you can install backup. I can upload my backup.
Click to expand...
Click to collapse
Hi.
I have the original software on my phone without root, i can make this operation ?
thankyou
Good evening,
I installed TWRP with flash tool, it works but missing the OS.
With flash tool i used those files:
logo.bin, lk.bin, MBR, preloader.bin, secro.img, MT6582_Android_scatter.txt, boot.img, recovery.img, system.img
But i don't have any files for:
ebr1, ebr2, cache, usrdata
If someone has got the files or can help me...
Thx you.
Firmware backups(TWRP)
ver208
ver213
Files must be in internal memory(you can copy it from external sd in TWRP)
Path:
/TWRP/BACKUPS/P4502/ver_or_date/files(boot.mmc.win,system.ext4.win ...)
Hi All,
Really annoying self inflicted problem, changed the swipe code, forgot it, google account ADM wont reset phone, no sequence of button pressing gets phone into recovery mode, USB debugging appears to be off. How can I save my phone??!??!?!?!? What sequence should I follow, what ROM should I install, need a step by step if at all possible, complete newbie!!1? Thanks in advance.
Jacko110 said:
Hi All,
Really annoying self inflicted problem, changed the swipe code, forgot it, google account ADM wont reset phone, no sequence of button pressing gets phone into recovery mode, USB debugging appears to be off. How can I save my phone??!??!?!?!? What sequence should I follow, what ROM should I install, need a step by step if at all possible, complete newbie!!1? Thanks in advance.
Click to expand...
Click to collapse
ok you are most likely on 20160810 where recovery does not work.
you are most likely on windows 10 as well. first lets find a rom where recovery works.
We can use 20160810 rom and wipe userdata partition..
Here is the download link https://mega.nz/#!ys4DTIxa!8rrL0aktVQ8W7Q4Et8fvQ8jk2tAxLZvJOJH48S9Vkyk .
Once you have finished downloading you should then extract it to a folder.
Next we need to prepare your computer for the flashing process by installing the correct drivers.
look in this thread http://forum.xda-developers.com/elephone-p9000/how-to/how-to-guideline-install-mtk-drivers-t3344042 scroll for your version of windows. follow the instructions and everything should work.
If you dont have add hardware option in windows then hit windows button and r and enter hdwwiz.exe.
now you have installed the drivers we need to download sp flash tools which is what we need to install the rom.
So go this website http://spflashtool.com/ now click on the first download link 'SPFlash Tool 5.1628' .
this will download a zip file. again extract it to a new folder. ok now you need to go in the flash tool and run flash_tool.exe by just clicking on it. now the software will load up.
You need to load the scatter file from the rom folder. The scatter file should be outside the encrypt folder and should be called MT6755_Android_scatter.txt . Now the rom should be loaded. You have some more options here, you can either untick all boxes and leave userdata (where your security and codes are stored) ticked or you can leave everything ticked which would flash the rom again. So once you have decided what option you have you need to turn your phone off. you then need to click download in flash tools and then connect your phone to the pc and hold the vol+ button. Then wait for it to flash, once the box with the tick opens you can close the program and restart your phone.
no recovery
there is no recovery in this build.........you have to flash one of your own.....
No recovery
Thank you, will start trying now and let you know.
Success!
Pro4TLZZ said:
ok you are most likely on 20160810 where recovery does not work.
you are most likely on windows 10 as well. first lets find a rom where recovery works.
We can use 20160810 rom and wipe userdata partition..
Here is the download link https://mega.nz/#!ys4DTIxa!8rrL0aktVQ8W7Q4Et8fvQ8jk2tAxLZvJOJH48S9Vkyk .
Once you have finished downloading you should then extract it to a folder.
Next we need to prepare your computer for the flashing process by installing the correct drivers.
look in this thread http://forum.xda-developers.com/elephone-p9000/how-to/how-to-guideline-install-mtk-drivers-t3344042 scroll for your version of windows. follow the instructions and everything should work.
If you dont have add hardware option in windows then hit windows button and r and enter hdwwiz.exe.
now you have installed the drivers we need to download sp flash tools which is what we need to install the rom.
So go this website http://spflashtool.com/ now click on the first download link 'SPFlash Tool 5.1628' .
this will download a zip file. again extract it to a new folder. ok now you need to go in the flash tool and run flash_tool.exe by just clicking on it. now the software will load up.
You need to load the scatter file from the rom folder. The scatter file should be outside the encrypt folder and should be called MT6755_Android_scatter.txt . Now the rom should be loaded. You have some more options here, you can either untick all boxes and leave userdata (where your security and codes are stored) ticked or you can leave everything ticked which would flash the rom again. So once you have decided what option you have you need to turn your phone off. you then need to click download in flash tools and then connect your phone to the pc and hold the vol+ button. Then wait for it to flash, once the box with the tick opens you can close the program and restart your phone.
Click to expand...
Click to collapse
Thank you soo much, all sorted. Take it that I can now use these tools and newly gained knowledge to upgrade OS???
Jacko110 said:
Thank you soo much, all sorted. Take it that I can now use these tools and newly gained knowledge to upgrade OS???
Click to expand...
Click to collapse
You can but be careful as you could damage your phone
Has anyone got a link to a custom recovery I can flash on to p9000 running latest ROM
haidar123 said:
Has anyone got a link to a custom recovery I can flash on to p9000 running latest ROM
Click to expand...
Click to collapse
http://forum.xda-developers.com/ele...nofficial-twrp-elephone-p9000-t3426678/page11 use a p9000 scatter file
Hi,
I have the same problem with my P9000 : Elephone_P9000_20160810, I even cannot install the last update 20170112 because the recovery mode is not working. but I use Linux mint on my laptop.
I already downloaded the Linux version of the flashing tool, give it a try but at the time of the flashing my laptop freeze. Scarred to death, I restarted my phone, no damage done, but now, after stay away from the idea the time to recover from my post traumatic syndrome disorder, I am ready to try again with the help of peoples knows what they are doing.
What are the points I have to be aware using Linux mint when I follow this tutorial.
Thanks for your time
New Recovery File
Need to use this one. I had the same problems https://redirect.viglink.com/?format=go&jsonp=vglnk_148541845062211&key=f0a7f91912ae2b52e0700f73990eb321&libId=iye3se1601000n4o000DA1jol7bnvwro0d&loc=https%3A%2F%2Fforum.xda-developers.com%2Fsitesearch.php%3Fq%3Dp9000%2520twrp%2520unofficial&v=1&out=https%3A%2F%2Fwww.google.com%2Furl%3Fq%3Dhttps%3A%2F%2Fforum.xda-developers.com%2Felephone-p9000%2Fdevelopment%2Frecovery-unofficial-twrp-elephone-p9000-t3426678%26sa%3DU%26ved%3D0ahUKEwiR2N_0rt_RAhUF5xoKHQaCAEUQFggEMAA%26client%3Dinternal-uds-cse%26usg%3DAFQjCNEDufTDo_BhHEYeYoUxe8gtq12xsw&title=General%20Search&txt=%5BRECOVERY%5D%20%3Cb%3EUnofficial%20TWRP%3C%2Fb%3E%20for%20Elephone%20%3Cb%3EP9000%3C%2Fb%3E%203.0.2-8
As someone who has done this a few times - and forgotten this vital step almost every time, just a reminder that when using SPFlash Tool - after you set up the scatter file, you click on download so that it is trying to communicate with the phone before you even plug the cable into the phone, then with your phone turned off you hold Vol+ as you plug in the cable. It should send the file almost instantly.
Hi.
I wrote problems with my wife's P9000 here: https://forum.xda-developers.com/showpost.php?p=72990392&postcount=14
And yes: no solution works. And either there is no stock recovery or this device can't find them.
I offer 50 Euro for help. My goal: to install custom recovery (most TWRP), install custom ROM (some stable version of Marshmallow) and root it.
I tried about 6 hours and I have had enough.
Except that I will be appreciate.
German? English?
Vielleicht kann ich helfen
One of the official ota p9000 updates has a corrupt recovery. This is why you can't get into the recovery and why the official update fails all the time. (I think).
About the flashing part with sp flashtools. You need to install those mtk drivers with the driver signature turned off in Windows. Otherwise those drivers can not be installed on you pc and flashing your phone can't be done. Just search Google for how to disable driver signature for your Windows version.
About the part of making a scatter file. You do not need to make a scatter file. It is included in Roms that have a scatter file with them (the roms that are ment to be flashed with sp flashtools).
If you want to flash a custom recovery with sp flashtools. You load the scatter file of a stock ROM and make sure, in the download screen of sp flashtools, the location points to the custom recovery .img file. And make sure there is a check mark on the left of the row for the recovery. Otherwise sp flashtools will simply skip that part with flashing.
If you want to install a custom ROM without spflashtool. You need a custom recovery and flash it via the recovery.
I hope I helped you enough. Because this how it works for me every time on every mtk phone (that I owned). I do not want your €50
MoRiA Cheo said:
Hi.
I wrote problems with my wife's P9000 here: https://forum.xda-developers.com/showpost.php?p=72990392&postcount=14
And yes: no solution works. And either there is no stock recovery or this device can't find them.
I offer 50 Euro for help. My goal: to install custom recovery (most TWRP), install custom ROM (some stable version of Marshmallow) and root it.
I tried about 6 hours and I have had enough.
Except that I will be appreciate.
Click to expand...
Click to collapse
Do you have somewhere easier to talk? whatsapp? my whatsapp is +351 910012132 i can help
MasterDK2015 said:
German? English?
Vielleicht kann ich helfen
Click to expand...
Click to collapse
Polish or english. ?
MoRiA Cheo said:
Polish or english. ?
Click to expand...
Click to collapse
Hi, Just a couple of questions.
When did you get the P9000?
What version of Windows?
Things to download
I recommend you install the 20170112 (store on computer)here
Extract the RAR file, it is contained in a folder, no need to extract in a new folder.
Super SU root (store on phone, SD card preferred) here
And TWRP 3.0.2-8 from Jonny (store on computer)here
Go to Device Manager.
View - Show Hidden Devices
If you see MTK Preloader VCOM
or MTK USB Device, that's good. More MTK xxxxx the better.
Open SP Flash Tool
Load the scatter file from the load button. 3rd row down. Go to the Extracted RAR file and select MT6755_Scatter.txt.
Then press the recovery file location name (C: USER ........ recovery.img) and navigate to the
TWRP 3.0.2-8.img and select that.
Now Press the Download (green down arrow) button and then use the stock cable and connect to a USB 2.0 port, then while pressing the volume up button, on the P9000, connect the phone to the other end of the cable.
A Red bar down the bottom saying Download DA 100% should appear and then a yellow bar and some percentage, which will take 5 or so minutes to go all yellow then a big green tick on a pop up should appear and it's done!
Then go to recovery which is Volume Up and Power at the same time untill the ELE logo appears. When it appears release the buttons. Swipe the allow modifications and then press the install button, navigate to the SuperSu.zip by Select storage if you have an SD CARD, otherwise it will probably be in the Download folder. Swipe to install, wipe cache and dalvik, swipe and reboot system. Hope that works any questions just ask. Sincerely, X
Hexyl said:
One of the official ota p9000 updates has a corrupt recovery. This is why you can't get into the recovery and why the official update fails all the time. (I think).
About the flashing part with sp flashtools. You need to install those mtk drivers with the driver signature turned off in Windows. Otherwise those drivers can not be installed on you pc and flashing your phone can't be done. Just search Google for how to disable driver signature for your Windows version.
About the part of making a scatter file. You do not need to make a scatter file. It is included in Roms that have a scatter file with them (the roms that are ment to be flashed with sp flashtools).
If you want to flash a custom recovery with sp flashtools. You load the scatter file of a stock ROM and make sure, in the download screen of sp flashtools, the location points to the custom recovery .img file. And make sure there is a check mark on the left of the row for the recovery. Otherwise sp flashtools will simply skip that part with flashing.
If you want to install a custom ROM without spflashtool. You need a custom recovery and flash it via the recovery.
I hope I helped you enough. Because this how it works for me every time on every mtk phone (that I owned). I do not want your €50
Click to expand...
Click to collapse
Your instructions was very, very good but a little bit general for me. I lost myself in Your shortcuts (device on/off, connected/disconnected). But when I finished, I see You wrote everything.
So thank You very much. You helped me very much, You showed me the instruction I didn't find before.
Ninja X said:
Hi, Just a couple of questions.
When did you get the P9000?
What version of Windows?
Things to download
I recommend you install the 20170112 (store on computer)here
Extract the RAR file, it is contained in a folder, no need to extract in a new folder.
Super SU root (store on phone, SD card preferred) here
And TWRP 3.0.2-8 from Jonny (store on computer)here
Go to Device Manager.
View - Show Hidden Devices
If you see MTK Preloader VCOM
or MTK USB Device, that's good. More MTK xxxxx the better.
Open SP Flash Tool
Load the scatter file from the load button. 3rd row down. Go to the Extracted RAR file and select MT6755_Scatter.txt.
Then press the recovery file location name (C: USER ........ recovery.img) and navigate to the
TWRP 3.0.2-8.img and select that.
Now Press the Download (green down arrow) button and then use the stock cable and connect to a USB 2.0 port, then while pressing the volume up button, on the P9000, connect the phone to the other end of the cable.
A Red bar down the bottom saying Download DA 100% should appear and then a yellow bar and some percentage, which will take 5 or so minutes to go all yellow then a big green tick on a pop up should appear and it's done!
Then go to recovery which is Volume Up and Power at the same time untill the ELE logo appears. When it appears release the buttons. Swipe the allow modifications and then press the install button, navigate to the SuperSu.zip by Select storage if you have an SD CARD, otherwise it will probably be in the Download folder. Swipe to install, wipe cache and dalvik, swipe and reboot system. Hope that works any questions just ask. Sincerely, X
Click to expand...
Click to collapse
You are the NINJA!
Thank You! Thanks to You I installed TWRP. Rest is easier.
You show me to install ANY MTK device and P9000 can be on. And You show me precisely that I should change the destination point for TWRP (so not default but the .img file).
And that was important for me. And thanks to You I did it.
Thank You.
Please write to me in private message Your account number or PayPal.
Thank You again.
MoRiA Cheo said:
You are the NINJA!
Thank You! Thanks to You I installed TWRP. Rest is easier.
You show me to install ANY MTK device and P9000 can be on. And You show me precisely that I should change the destination point for TWRP (so not default but the .img file).
And that was important for me. And thanks to You I did it.
Thank You.
Please write to me in private message Your account number or PayPal.
Thank You again.
Click to expand...
Click to collapse
No problem. I'll PM my PayPal soon. Thanks!