Hello, i'm having some problems with an MTK 6572_S00 GT-I9500 Clone. I flash to it a wrong firmware and brick it really bad, after a few days of downloading tools, drivers and firmwares, managed too install the proper drivers (PreloaderUSB and DA USB) and with that flash a rom wich makes the phone to power on a red led (then it goes blue), the capacitive bottons and when i touch the power botton it makes a sound like is the screen was unlocking, but the problem is that the screen remains black, it doesn't do anything.
So... The problems that i'm having right know are:
1- The phone looks like is booting up, but the screen never do anything
2- I cannot flash another firmware to the phone, the ones that i have downloaded shows me an error message that says "Nand Flash was not detected"
3- I make a backup of my original firmware before flash anything to it, but i when i tryed to restore it, the SP Flash Tools showed to me an message error wich says that my phone was an MT6572_S00 and i tryed to flash a ROM for an MT6589.
Any ideas will help!
Adding some recently news:
Flashed some part of another firmware and made to screen lights up but the phone still doesn't boot in the regular way. When i push Volume + and Power botton it boots on Factory mode i think because it shows a black menu with three boot options (Recovey, Fastboot and Normal). If i pick Normal or Recovery mode the screen goes blank and starts to blink, if pick Fastboot shows a message that says Fastboot Mode On or something like that.
Download mode
elfanto said:
Hello, i'm having some problems with an MTK 6572_S00 GT-I9500 Clone. I flash to it a wrong firmware and brick it really bad, after a few days of downloading tools, drivers and firmwares, managed too install the proper drivers (PreloaderUSB and DA USB) and with that flash a rom wich makes the phone to power on a red led (then it goes blue), the capacitive bottons and when i touch the power botton it makes a sound like is the screen was unlocking, but the problem is that the screen remains black, it doesn't do anything.
So... The problems that i'm having right know are:
1- The phone looks like is booting up, but the screen never do anything
2- I cannot flash another firmware to the phone, the ones that i have downloaded shows me an error message that says "Nand Flash was not detected"
3- I make a backup of my original firmware before flash anything to it, but i when i tryed to restore it, the SP Flash Tools showed to me an message error wich says that my phone was an MT6572_S00 and i tryed to flash a ROM for an MT6589.
Any ideas will help!
Adding some recently news:
Flashed some part of another firmware and made to screen lights up but the phone still doesn't boot in the regular way. When i push Volume + and Power botton it boots on Factory mode i think because it shows a black menu with three boot options (Recovey, Fastboot and Normal). If i pick Normal or Recovery mode the screen goes blank and starts to blink, if pick Fastboot shows a message that says Fastboot Mode On or something like that.
Click to expand...
Click to collapse
I'm no expert at unbricking. Does it show a screen to go to download mode when u press volume down+home+power button when turned off?
NoobInToto said:
I'm no expert at unbricking. Does it show a screen to go to download mode when u press volume down+home+power button when turned off?
Click to expand...
Click to collapse
Nope! I just try it, but screen lights up and starts to blink
Enviado desde mi ST25i usando Tapatalk 2
Related
I tried to Unroot my Galaxy Tab 10.1 LTE last night and think I may have bricked my tablet. I used the instructions here on the XDA forum which had a link to all the Stock ROM's in one place. I got the most recent one and the only one for USA but it said it was for the model 7510. I didn't think that would be a problem since the USB drivers I installed on my PC were also labeled as being for the 7510 and they worked.
This tablet is the SCH-I905. Now I can't get it to boot at all. Gets stuck in a boot loop. Shows the Samsung logo, then resets and does it again. I can't get it in recovery mode either. Goes to a black screen and hangs.
Using the normal process to get to Download mode doesn't work. Holding Power and Volume Up, then letting go of the Power button, then pressing Volume Down and then Up. That's one weird thing. I can get to the option screen that shows the Download and Recovery mode options. Normally I would hit the Volume Down button to select Download mode and on the screen it says to press Volume Up to continue or Volume Down to cancel. If I press Volume Up it goes to a black screen and hangs. If I press Volume Down I get the Odin Download screen that says Waiting on USB cable.
That screen doesn't look the same as what I normally see but I'm not sure what's different. I didn't memorize each line of text. I just know there's not as much text there as there usually is. My PC will not recognize the tablet no matter which USB port I try to use and the tablet doesn't recognize that the USB cable is plugged in. I had no problem with the USB connection before I flashed the 7510 stock ROM.
So, if I cannot get to recovery mode and I can't get Download mode to work so I can use Odin to flash a different rom then is this thing bricked or is there something else I can try? I am about to try using my laptop and its USB ports but I don't think that's going to make any difference.
BTW, I have since found the correct 'stock recovery rom' at droidbasement.com and downloaded it to my PC. I just need to get on the tablet somehow.
Many people have your problem. I have my Lte verizon bricked as yours. The problem is demaged bootloader, only nvflash can fix it but actually our bootloader is locked and we need a hex key called sbk. At least we have to wait that somebody hack our tab from the basement. For now we can only search and share result.
pickupcash said:
I tried to Unroot my Galaxy Tab 10.1 LTE last night and think I may have bricked my tablet. I used the instructions here on the XDA forum which had a link to all the Stock ROM's in one place. I got the most recent one and the only one for USA but it said it was for the model 7510. I didn't think that would be a problem since the USB drivers I installed on my PC were also labeled as being for the 7510 and they worked.
This tablet is the SCH-I905. Now I can't get it to boot at all. Gets stuck in a boot loop. Shows the Samsung logo, then resets and does it again. I can't get it in recovery mode either. Goes to a black screen and hangs.
Using the normal process to get to Download mode doesn't work. Holding Power and Volume Up, then letting go of the Power button, then pressing Volume Down and then Up. That's one weird thing. I can get to the option screen that shows the Download and Recovery mode options. Normally I would hit the Volume Down button to select Download mode and on the screen it says to press Volume Up to continue or Volume Down to cancel. If I press Volume Up it goes to a black screen and hangs. If I press Volume Down I get the Odin Download screen that says Waiting on USB cable.
That screen doesn't look the same as what I normally see but I'm not sure what's different. I didn't memorize each line of text. I just know there's not as much text there as there usually is. My PC will not recognize the tablet no matter which USB port I try to use and the tablet doesn't recognize that the USB cable is plugged in. I had no problem with the USB connection before I flashed the 7510 stock ROM.
So, if I cannot get to recovery mode and I can't get Download mode to work so I can use Odin to flash a different rom then is this thing bricked or is there something else I can try? I am about to try using my laptop and its USB ports but I don't think that's going to make any difference.
BTW, I have since found the correct 'stock recovery rom' at droidbasement.com and downloaded it to my PC. I just need to get on the tablet somehow.
Click to expand...
Click to collapse
Did you solved the issue?
Please share ..., i face the same problem now ...
regards,
erwien.
Did you solved the issue.
share me......i face the same problem now
.
.
.
.
.
.
.
.
.
.
.
.
help me plz
Sorry, i'm new here, i've downloaded roms and some other stuff here, but now i have a serious problem. I had this GoogleBeAnZP rom on my phone (i had root, unlocked bootloader and CWM) and it was fine!!! actually it was running smooth, but i wanted to try another rom, i tried to instal a JB custom rom that i saw over the internet, so i entered the recovery mode and installed this rom with aroma installer. it said that everything was installed, and that it was going to reboot, so i waited, and NOTHING HAPPEND!!! now, i try to enter flashmode to instal the rom from flashtool and i can't even enter flash mode. my cellphone is really dead, all it does is turn a red light when i connect it. once it turned on the green light like when it enters flash mode but not anymore. I've hold the down button before connecting it, like a hundred times, trying to reboot the phone pressing the up volume button and the power button at the same time but its dead. it keeps showing the red LED indicator but not starting. i've been reading hundreds of posts but no cellphone does what mine does. i tried SEUS, flashtool but both require flashmode and I simply can't enter!!
All i get is this red light from the LED but no response in my phone. the screen doesn't blink neither vibrates
HEEELLLLP!!!!!
I have been reading posts for days in multiple Xperia forums here trying to identify my soft brick condition.
I had a bad flash using flash mode, and the device just keeps power cycling with no logos. I turn it on, and I receive one "buzz" followed by a red light, then a green light, then it goes back off.
If I hold vol down for flash mode, this just repeats over and over.
If I old up for Fast boot, it does go into fast boot, but this is a VZW locked boot loader, and I can not do much in fast boot mode due to these restrictions.
If anyone knows a hack to unlock the boot loader or some other way to fix the flash mode so I can re-flash, it would be greatly appreciated!
When the read and green leds are going off ypu should be in flashmode
Look on your pc device manager and ypu will see the device therw
When the red light flashes, it buzzes, then the green light comes on for a brief second, then it reboots immediately and I never see the device show up in device manager. The Flashtool also never recoginzies the device either while it is in this cycle of kernel rebooting (I assume it is just the kernel attempting to boot since it can go into fastboot).
rcstar6696 said:
When the read and green leds are going off ypu should be in flashmode
Look on your pc device manager and ypu will see the device therw
Click to expand...
Click to collapse
usually when i mess this phone up i am able to use the companion to flash it back to stock. i tryed to flash magisk and now the light flashes when plugged into a power source and the phone does not turn on at all. if i hold volume up while turning on it boots into fastboot mode because i see the blue light and i was able to use flashtool and its fastboot tools to flash system.sin from stock firmware but that has not made a difference. i have tried to get it into download mode(upgrade mode) by holding volume down but it continues to boot loop. if the device is not plugged into power and i hold volume down and power it boots into recovery and i click both safe mode and factory reset but both turn the device off. any ideas?
ths is far from beeig bricked. go into twrp recovery and flash new rom. this should work.
It is just a dead mobile
TjNiko said:
ths is far from beeig bricked. go into twrp recovery and flash new rom. this should work.
Click to expand...
Click to collapse
mine is not doing anything but it only boots into fastboot mode.
my device : Z3v D6708
rooted
no twrp is able to accessed.
dead body which blinks red+green LED when plugged in....and shows a blue light in fastboot.
Inside the SD card / SIM card slot is a small orange or red button, press with a tooth pick or a pin untill you feel vibration and then try to reflash.
a recovery shouzld be aways present at fota my friend.
rockinroller said:
Inside the SD card / SIM card slot is a small orange or red button, press with a tooth pick or a pin untill you feel vibration and then try to reflash.
Click to expand...
Click to collapse
i held the button in the sim card slot until the phone vibrated but what's next? i tried the companion and flashtool but the only thing it lets me do is flash the system, which does not fix my problem still, what is that button?
TjNiko said:
a recovery shouzld be aways present at fota my friend.
Click to expand...
Click to collapse
the only recovery available is the stock one that says power off, safe mode, continue boot, factory reset... none of them do anything....this device does have a locked bootloader, it uses a recovery like many motorola's do... its a software recovery so its gone lol
You should be able to use flash tool to flash the proper ftf file for your device. That is what you are trying to do right?
rockinroller said:
You should be able to use flash tool to flash the proper ftf file for your device. That is what you are trying to do right?
Click to expand...
Click to collapse
yes, every time i try it asks to put the device is upgrade mode, which it can not do at the moment
logan71f100 said:
yes, every time i try it asks to put the device is upgrade mode, which it can not do at the moment
Click to expand...
Click to collapse
So, if you hit the flash button on flashtool, tick the flashmode and after preparing it asks you to power off your phone and plug your USB cable into your computer and then press the volume button "down" while plugging in the USB cable to your phone, It should enter flashmode and start a automated flash. This is not working?
rockinroller said:
So, if you hit the flash button on flashtool, tick the flashmode and after preparing it asks you to power off your phone and plug your USB cable into your computer and then press the volume button "down" while plugging in the USB cable to your phone, It should enter flashmode and start a automated flash. This is not working?
Click to expand...
Click to collapse
nope thats my problem, i only can access flashmode, when plugged in it just bootloops, it only goes into flash mode via the blue light
logan71f100 said:
nope thats my problem, i only can access flashmode, when plugged in it just bootloops, it only goes into flash mode via the blue light
Click to expand...
Click to collapse
I'm not understanding how it is bootlooping. Your phone should be off (power off) when holding down the volume button and plugging in the USB. Is your phone powering on at this point to bootloop? If so you might have hardware problems Is all I can think of.
rockinroller said:
I'm not understanding how it is bootlooping. Your phone should be off (power off) when holding down the volume button and plugging in the USB. Is your phone powering on at this point to bootloop? If so you might have hardware problems Is all I can think of.
Click to expand...
Click to collapse
the phone started bootlooping after flashing that zip. so that rules out hardware, and when i say boot loop i mean lights flash screen stays dark..im trying to figure out if there's a fancy way to fix this through fastboot
depends on wich ftf was used before and bootloader some of them can enter flashmode just by put on the otg cable
It was running 5.1.1 and it boots into fastboot when I hold volume up, but just lights and virbates when holding down for upgrade mode
Same problem. z3v, accidentally flashed a wrong firmware zip via TWRP.
Now if I push the power button, nothing happens.
A long push causes a short vibration and nothing else.
Yellow rest button does not change anything either.
If I connect it to the PC, the following happens: Red led lights up briefly, phone vibrates, green led lights up briefly; whole sequence cycles after that. Now the only thing I can do from there is hold volume up for a couple of seconds, then the phone enters fastboot mode. Blue led lights up continuously. Flashtool sees the phone in Fastboot mode.
However, where to go from here, I cannot see. Any advise?
I had this problem once. It might be your usb cable try a brand new one that rated for data also not just charging. I was trying to root my phone at work and it wouldnt work and when I got home I tried a different usb cable and it worked.,
s300pmu1 said:
Same problem. z3v, accidentally flashed a wrong firmware zip via TWRP.
Now if I push the power button, nothing happens.
A long push causes a short vibration and nothing else.
Yellow rest button does not change anything either.
If I connect it to the PC, the following happens: Red led lights up briefly, phone vibrates, green led lights up briefly; whole sequence cycles after that. Now the only thing I can do from there is hold volume up for a couple of seconds, then the phone enters fastboot mode. Blue led lights up continuously. Flashtool sees the phone in Fastboot mode.
However, where to go from here, I cannot see. Any advise?
Click to expand...
Click to collapse
I am no closer than when I posted this, until there is a bootloader unlock witch in theory can be done through fastboot, we are s.o.l.
logan71f100 said:
I am no closer than when I posted this, until there is a bootloader unlock witch in theory can be done through fastboot, we are s.o.l.
Click to expand...
Click to collapse
aaa,It's very easy.you can use flashtool to flash a new system. but you must be in green light.only it.you also can be flash.sure,if your phone can't get into system,it only loop at"SONY".You touch the power and the volume up and down. keep 7s. then the phone will get into 3E RECOVERY,you chosed power down.and then the phonwill be power off. Now you can flash you phone.
If you phone can't get into green light.you can use the tool Z3X easy tool to save your phone.or it will be a brick.
my phone cant be start.it have became a brick. Good luck
s300pmu1 said:
Same problem. z3v, accidentally flashed a wrong firmware zip via TWRP.
Now if I push the power button, nothing happens.
A long push causes a short vibration and nothing else.
Yellow rest button does not change anything either.
If I connect it to the PC, the following happens: Red led lights up briefly, phone vibrates, green led lights up briefly; whole sequence cycles after that. Now the only thing I can do from there is hold volume up for a couple of seconds, then the phone enters fastboot mode. Blue led lights up continuously. Flashtool sees the phone in Fastboot mode.
However, where to go from here, I cannot see. Any advise?
Click to expand...
Click to collapse
I have same problem if you resolve it please help
So i was using RessurectionRemix (a version from last month) and recovery twrp 3.1.0-0 and the phone was working great!
Yesterday i left my phone charging over night and in the morning i wake up to my phone bootlooping!
So i tried different things including everything it says here https://forum.xda-developers.com/le-max-2/how-to/guide-hard-brick-fix-qualcomm-hs-usb-t3492949 without luck
I can get it into recovery and fastboot but as soon as i let the key combination go the phone stops and just shows a black screen (screen is on) and i cant get into qualcomm recovery to flash!
And the only way to shut off the phone is by holding power + vol up + vol down!
Any solution or suggestions?
Use flashone method to unbrick
md07 said:
Use flashone method to unbrick
Click to expand...
Click to collapse
As i already mentioned i cant get into qualcomm recovery so i cant use flashone
try to flash fastboot rom from cucoco's.
Tsoler said:
As i already mentioned i cant get into qualcomm recovery so i cant use flashone
Click to expand...
Click to collapse
connect phone to computer, try force shutdown phone by hard button, ater phone shutdown, immediately release power but keep both volume. Phone maybe will enter Qualcomm flash dead mode, and Flashone will regconize com phone (refresh nedded)
Hope you success ! And believe, if a phone can flash with Qfil or Flashone, almost that phone never die (software)
Are you able to connect to the phone via Vysor, either via Chrome browser or as a standalone app on Windows PC when you do not see anything on the phone screen? Please post if Vysor install goes thru successfully. Hope your developer options/USB debugging are on. I assume your phone boots but may have display issues either hw or sw.
md07 said:
connect phone to computer, try force shutdown phone by hard button, ater phone shutdown, immediately release power but keep both volume. Phone maybe will enter Qualcomm flash dead mode, and Flashone will regconize com phone (refresh nedded)
Hope you success ! And believe, if a phone can flash with Qfil or Flashone, almost that phone never die (software)
Click to expand...
Click to collapse
Did what you said but nothing happens
kayyappan said:
Are you able to connect to the phone via Vysor, either via Chrome browser or as a standalone app on Windows PC when the you do not see anything on the phone screen? Please post if Vysor install goes thru successfully. Hope your developer options/USB debugging are on. I assume your phone boots but may have display issues either hw or sw.
Click to expand...
Click to collapse
Phone gets recognized but not long enough to do anything (windows makes sound but doesn't install anything and doesn't show up in device manager)
try this guide
https://www.gizmochina.com/2016/11/20/leeco-x820-max-2-super-unbrick-guide/
You have mentioned that you are able to see the device in recovery and fastboot till you release the buttons - does this mean if the buttons are held say in fastboot mode you are able to see the device via "fastboot devices" or in recovery the twrp screen or nothing ever shows up at all? Are the buttons clicking properly? Check individually to make sure - particularly the power button. Does it vibrate at any point of time when you press and hold the power button? Are you able to see any backlight when you say the screen is on?
If there no backlight shine a torch or sunlight from the side of the screen to see anything at all on the screen.
Vysor reports apk not installed when it attempts to download from PC to phone but fails. With Vysor you will have two windows one showing status of phone - this is the main window. The other is the mirrored one - that of the phone when you click view on the main window. I forgot that the phone requires approval to install the apk. Please see the attached thumbnails. Keep touching the screen about 3 cms up from the bottom of the screen (not the phone) to see any change. Hope your touch works.
I know it is quite frustrating to try a number of things. I recently went thru the same on Galaxy S4 to make sure the phone but for the screen works OK prior to ordering the screen. Besides in my case developer options was disabled and touch also did not work. It took about a week of learning and trying to see something on Vysor. I never have used a Sam phone till that time this broken phone was handed over to me.
After a lot of trying i found out that when i keep pressed power + vol down or vol up while connected to pc and device is off it gets recognized as
qualcomm hs-usb qdloader 9008 long as i keep the keys pressed so i tried the flashone method but it just says could not connect
Are Qualcomm drivers loaded on your computer? I have not used flashone. I used QPST to see if phone is connected. I am not sure if they are same.
kayyappan said:
You have mentioned that you are able to see the device in recovery and fastboot till you release the buttons - does this mean if the buttons are held say in fastboot mode you are able to see the device via "fastboot devices" or in recovery the twrp screen or nothing ever shows up at all? Are the buttons clicking properly? Check individually to make sure - particularly the power button. Does it vibrate at any point of time when you press and hold the power button? Are you able to see any backlight when you say the screen is on?
If there no backlight shine a torch or sunlight from the side of the screen to see anything at all on the screen.
Vysor reports apk not installed when it attempts to download from PC to phone but fails. With Vysor you will have two windows one showing status of phone - this is the main window. The other is the mirrored one - that of the phone when you click view on the main window. I forgot that the phone requires approval to install the apk. Please see the attached thumbnails. Keep touching the screen about 3 cms up from the bottom of the screen (not the phone) to see any change. Hope your touch works.
I know it is quite frustrating to try a number of things. I recently went thru the same on Galaxy S4 to make sure the phone but for the screen works OK prior to ordering the screen. Besides in my case developer options was disabled and touch also did not work. It took about a week of learning and trying to see something on Vysor. I never have used a Sam phone till that time this broken phone was handed over to me.
Click to expand...
Click to collapse
It doesn't stay long enough in recovery or fastboot to do anything it shuts off after a few seconds even with the buttons pressed after that it just shows a black screen
Phone vibrates when i press power and shows leeco logo (not os logo) and after 1-2 seconds screen goes black and phone vibrates again and shows leeco logo again and just continues looping
if i try to press power + vol up normally it goes into recovery but as soon as recovery is loaded screen goes black (screen on just doesn't show anything) the same goes for fastboot if i press power + vol down it loads fastboot but after 1-2 seconds screen goes black
if i keep pressing keys the phone just stays longer in recovery/fastboot but only 4-5 seconds
I assume you have adb and fastboot. Since you say the screen remains on when booting to recovery open a command prompt at the directory where adb is and issue a command "adb devices" without quotes. Does it just exit without showing any device or throws up some error? Try this irrespective of the black screen.
Have you looked at and tried what is given by @HTC-TYTN2 at post #8? It is for Le Max 2 and you will find a link to Quallcomm drivers too. Do not bother that the link mentions X820 even your Max 2 is 821, 829, etc.
since it happened after charging, you might want to check your cable and battery. best is to get a cheap usb multimeter.
Gesendet von meinem LEX820 mit Tapatalk
I too thought it could be the battery based on that's the screen goes off. But he also mentioned that the screen remains on but nothing to be seen after a short while. Wanted to suggest slow speed charging probably via a laptop usb as I'm not sure if he used high speed charging resulting in battery issue.
Did you solve the problem?
My phone just died completely! No response at all anymore. I'm contacting the seller now to send the phone back.
Looks like it is a hardware defect! A pretty odd one but nothing i can do anymore. I send it back and post what the problem is as soon as get any information.
Thanks to everyone who tried to help!
Tsoler said:
My phone just died completely! No response at all anymore. I'm contacting the seller now to send the phone back.
Looks like it is a hardware defect! A pretty odd one but nothing i can do anymore. I send it back and post what the problem is as soon as get any information.
Thanks to everyone who tried to help!
Click to expand...
Click to collapse
Try this:
https://www.androidfilehost.com/?w=files&flid=136823
download file, unzip, open folder, connect phone to USB via fastboot ( phone off phone + hold volume -) . Click to the flash app in your PC. The app should find the phone. Confirm TWRP problem -NO and start flash.
Drivers must be installed.
Drivers here.
https://uloz.to/!A6B4AmEVx87S/adbdriverinstaller-exe
I can, pass the cuoco rom by qfil? Another type of flash, because I can not access recovery and twrp ?, only by fastboot
RaphaBraga23 said:
I can, pass the cuoco rom by qfil? Another type of flash, because I can not access recovery and twrp , only by fastboot
Click to expand...
Click to collapse
Try this via fastboot mode.:
https://www.androidfilehost.com/?w=files&flid=136823
download file, unzip, open folder, connect phone to USB via fastboot ( phone off phone + hold volume -) . Click to the flash app in your PC. The app should find the phone. Confirm TWRP problem -NO and start flash.
Drivers must be installed.
Drivers here.
https://uloz.to/!A6B4AmEVx87S/adbdriverinstaller-exe