This was my question before I converted it into a tutorial:
Sorry if this question was posted before (I did ask this in the NOOB-FRIENDLY thread, but didn't get a constructive answer)
My Xperia Neo V dropped into water.
Dried it with rice for a whole day and turned it on. Success! Was able to even play games.
Then I sent it for charging. (Battery was 8%)
5 mins later, it died.
Responds by entering flashmode after blinking red LEDs (3 I think), so I flashed stock.
Still couldn't start, so I sent it for charging (No response either after some hours)
I abandoned it and switched to a Galaxy Ace...until now....
Connected it to PC a month later.
It blinks red LED continuously, unplugged it and plugged it to a charger. No LED response whatsoever.
Plugged to PC again and POOF! Magic.
Detected by PC as my old MT11i :'D
LED is green, can do file exploration. Buttons are lit, vibrates when I press shutter button. No sound with the volume buttons
So the verdict...
CAN I STILL REVIVE MY NEO V?
IS MY DISPLAY DAMAGED?
This tutorial was made possible by @xange and @georgeiulian89. Thanks!
Usually when you drop your phone, you would be doomed. Or so you thought. With this tutorial, you can save A LOT of money buying a new phone or repairing the wet phone!
HOWEVER, I CANNOT GUARANTEE THAT YOUR PHONE CAN REVIVE. THIS WORKED FOR ME (SHALLOW DIP IN WATER). YOU MIGHT ALSO NEED A NEW BATTERY (IF YOU THINK YOU CAN REVIVE IT)
Steps(suggested by xange, proved):
1. Remove your phone from the water source IMMEDIATELY! (duh) DO NOT ATTEMPT TO SWITCH IT ON OR PRESS ANY BUTTON.
2.Remove the battery, SIM and micro SD cards.
3.Dry the body with a dry cloth. Try not to use tissue paper as it will leave residue.
4.Disassemble the phone, all the way to the motherboard. I used a small slotted screwdriver (the one with only one edge)as there are screws shaped like stars. If you have that type of screwdriver you can use it. Similar disassembly video here: www.youtube.com/watch?v=ginuDIeNCs8
WARNING: INTERNAL PARTS ARE VERY SENSITIVE TO STATIC, METAL,ETC. BE CAREFUL. ALSO REMOVE THE CONNECTIONS TO THE FRONT COVER AND DIGITIZER (display) BEFORE REMOVING THEM.
5.Direct a blowing fan to all the internal parts to dry them. Keep the screws and parts in an accessible area. Leave it for 30 minutes. DO NOT DRY IT WITH A HAIRDRYER. YOU ARE JUST TRYING TO SCREW YOUR PHONE.
6.Reassemble the phone and insert the battery ONLY. NOTE: Make sure the ribbon connector is clean before connected, if dust (or any tiny electric conductor) sticks on the connector while connecting them, you will have high chancesof damaging the phone. Then, switch on the phone. If not,
A) CHARGE IT: Your phone battery might be 100% dead(until normal charging can't power it on). For me I pressed and held the Back button while plugging the charger into the phone (Flashmode). The LED should blink red and eventually, green. This is when normal charging starts.
B) REPLACE THE BATTERY: You'll need to do so especially when the (once)white area near the connectors of the battery has turned red, indicating battery damage.
C) SEND IT TO A (optional: AUTHORIZED) SERVICE CENTER: Out of luck. This is the furthest I can help.
ALTERNATIVE DRYING METHODS:
A)PUT IT IN RICE FOR A DAY: NO, Asians won't come to repair your phone. Rice acts like silica, which absorbs moisture like sponge. I suggest you disassemble the phone first as rice might get into the small holes around your phone.
B)SOAK IN ALCOHOL, THEN PUT IT OUT: Disassemble it first, too. Though I haven't tried this method, there are those who have proved it to work.
C) RADIATOR DRYING (suggested by georgeiulian89): I've turned it off,i've removed the back cover, took out the battery, sim card and sd card, and i've put the phone on the radiator (i've put a towel between the phone and the radiator and i've placed the phone on the towel). I've left the phone about two hours to dry, and then i've inserted back the sim, sd card and the battery and turned it on.
C)DRY IT WITH A HAIRDRYER: NO. RISKY METHOD. Water will evaporate, then condense back somewhere once you've done hairdrying your phone it will condense back. I tried it and it condensed on my phone's camera lens. (It's a hairdryer, not a phonedryer!)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Hope this tutorial helps those out there whose phones have went swimming (or diving)
THANK ME IF I HELPED
Jessss
Sent from my Xperia Neo V using XDA Premium 4 mobile app
karanrajkapur said:
Jessss
Sent from my Xperia Neo V using XDA Premium 4 mobile app
Click to expand...
Click to collapse
If you mean yes, then HOW?
fenzo3 said:
If you mean yes, then HOW?
Click to expand...
Click to collapse
What i believe is you've broken your battery and i didn't get anything what you asking about the display. It doesn't light up or what???
Sent from my Xperia Neo V using XDA Premium 4 mobile app
I dropped my Xperia Neo into water for 3 times, yet still operable, i mean, it survived 3 times of dropped into a pail of water, NO JOKES! .
What you should do is, the moment you dropped your phone into water, pick it out of water immediately, open the back cover and take out the battery immediately to prevent further electric short circuit. You will need some small tool to open every single screw to get the mother board come out (careful when unplug those ribbon sockets, if it breaks, you may have to pay to replace it) and dry (using hair dryer?) every single spot in the phone, except the screen, the screen should be tightly seal and should have no water enter into it. maybe the rubber physical buttons you have to take out and dry it too. (DON'T open the screen no matter what happen, unless water really enters the screen, or else the dust enter and stick at the screen you will have a REALLY HARD TIME { i mean it } to clean those dust out of the screen) confirm everything is dried and then assemble it. (from here onwards, it is a luck test whether you still able to save your phone or not, a line between hell and heaven) Put in your battery, It is normal you may not able to turn on your phone at first, give it a charge about 20 minutes and leave it there (red LED may blink repeat-ly for a while and you will not able to turn it on, just leave it) then switch it on, If you still can't turn it on, try change the battery. If symptom persist, god bless you, i tried my best helping you. ( it means it may not 100% probability to save your phone, but it is a way i did to save my phone)
Eventhough my phone survived dropping into water for 3 times, but it has some problems now, a random one, the phones get really really hot for no reasons for a short period (about 1 hour to 2 days) the heat comes from the motherboard after my inspection, maybe some water droplet enter into the chips and causing electric short circuit?
Good luck.
xange said:
I dropped my Xperia Neo into water for 3 times, yet still operable, i mean, it survived 3 times of dropped into a pail of water, NO JOKES! .
What you should do is, the moment you dropped your phone into water, pick it out of water immediately, open the back cover and take out the battery immediately to prevent further electric short circuit. You will need some small tool to open every single screw to get the mother board come out (careful when unplug those ribbon sockets, if it breaks, you may have to pay to replace it) and dry (using hair dryer?) every single spot in the phone, except the screen, the screen should be tightly seal and should have no water enter into it. maybe the rubber physical buttons you have to take out and dry it too. (DON'T open the screen no matter what happen, unless water really enters the screen, or else the dust enter and stick at the screen you will have a REALLY HARD TIME { i mean it } to clean those dust out of the screen) confirm everything is dried and then assemble it. (from here onwards, it is a luck test whether you still able to save your phone or not, a line between hell and heaven) Put in your battery, It is normal you may not able to turn on your phone at first, give it a charge about 20 minutes and leave it there (red LED may blink repeat-ly for a while and you will not able to turn it on, just leave it) then switch it on, If you still can't turn it on, try change the battery. If symptom persist, god bless you, i tried my best helping you. ( it means it may not 100% probability to save your phone, but it is a way i did to save my phone)
Eventhough my phone survived dropping into water for 3 times, but it has some problems now, a random one, the phones get really really hot for no reasons for a short period (about 1 hour to 2 days) the heat comes from the motherboard after my inspection, maybe some water droplet enter into the chips and causing electric short circuit?
Good luck.
Click to expand...
Click to collapse
I followed a disassembly video for the Neo, but unfortunately the Neo V has a slightly different assembly, so I could not remove the screen to get access to the motherboard. Also, before I put it in rice, I tried to turn it on (Sony said it was water-resistant) after 12 hours in rice. The screen went all weird but I could hint the LegacyXperia kernel logo. That was before my phone booted up normally, and died upon charging.
For your heat problem, perhaps rust? Water should have evaporated from the heat and condensed everywhere in the motherboard.
Would soaking it in alcohol help?
fenzo3 said:
Sorry if this question was posted before (I did ask this in the NOOB-FRIENDLY thread, but didn't get a constructive answer)
My Xperia Neo V dropped into water.
Dried it with rice for a whole day and turned it on. Success! Was able to even play games.
Then I sent it for charging. (Battery was 8%)
5 mins later, it died.
Responds by entering flashmode after blinking red LEDs (3 I think), so I flashed stock.
Still couldn't start, so I sent it for charging (No response either after some hours)
I abandoned it and switched to a Galaxy Ace...until now....
Connected it to PC a month later.
It blinks red LED continuously, unplugged it and plugged it to a charger. No LED response whatsoever.
Plugged to PC again and POOF! Magic.
Detected by PC as my old MT11i :'D
LED is green, can do file exploration. Buttons are lit, vibrates when I press shutter button. No sound with the volume buttons
So the verdict...
CAN I STILL REVIVE MY NEO V?
IS MY DISPLAY DAMAGED?
Click to expand...
Click to collapse
I guess that it's a problem with the battery, not with the display (probably the battery has been short-circuited). I dropped my phone (Xperia Neo) in water 3 days ago. I've took it out after about 10-15 seconds (this was the time until i've realised that it dropped). The phone was still working fine, it didn't shut down by itself. What i did: I've turned it off,i've removed the back cover, took out the battery, sim card and sd card, and i've put the phone on the radiator (i've put a towel between the phone and the radiator and i've placed the phone on the towel). I've left the phone about two hours to dry, and then i've inserted back the sim, sd card and the battery and turned it on. Gues what: it works without any problem, just like before the incident. You should check the water damage indicator on the battery (it's a white strip near the connectors of the battery). If it's white, the phone don't have any problem, but if it's pink or red, the phone was damaged by the water. Mine it's white, with some very little pink on the edge (before it was completely white).
georgeiulian89 said:
I guess that it's a problem with the battery, not with the display (probably the battery has been short-circuited). I dropped my phone (Xperia Neo) in water 3 days ago. I've took it out after about 10-15 seconds (this was the time until i've realised that it dropped). The phone was still working fine, it didn't shut down by itself. What i did: I've turned it off,i've removed the back cover, took out the battery, sim card and sd card, and i've put the phone on the radiator (i've put a towel between the phone and the radiator and i've placed the phone on the towel). I've left the phone about two hours to dry, and then i've inserted back the sim, sd card and the battery and turned it on. Gues what: it works without any problem, just like before the incident. You should check the water damage indicator on the battery (it's a white strip near the connectors of the battery). If it's white, the phone don't have any problem, but if it's pink or red, the phone was damaged by the water. Mine it's white, with some very little pink on the edge (before it was completely white).
Click to expand...
Click to collapse
Thanks for the tip but in all-summer Singapore we don't have radiators.
UPDATE: After following steps by @xange to reassemble and charge my Neo V, it BEAUTIFULLY WORKED!
The catch: Battery calibration problem, stuck at 100%. I'll figure a way out. Thanks a lot devs!
fenzo3 said:
Thanks for the tip but in all-summer Singapore we don't have radiators.
UPDATE: After following steps by @xange to reassemble and charge my Neo V, it BEAUTIFULLY WORKED!
The catch: Battery calibration problem, stuck at 100%. I'll figure a way out. Thanks a lot devs!
Click to expand...
Click to collapse
To get rid of 100% battery issue, you might just want to flash stock ftf in the first place, give it a full charge and then flash your desired driver.
Sent from my Xperia Neo V using XDA Premium 4 mobile app
fenzo3 said:
Thanks for the tip but in all-summer Singapore we don't have radiators.
UPDATE: After following steps by @xange to reassemble and charge my Neo V, it BEAUTIFULLY WORKED!
The catch: Battery calibration problem, stuck at 100%. I'll figure a way out. Thanks a lot devs!
Click to expand...
Click to collapse
try battery calibrator by zeppelinrox. i couldn't recall where he put the script. try search around XDA.... good luck.
---------- Post added at 09:26 PM ---------- Previous post was at 09:16 PM ----------
fenzo3 said:
This was my question before I converted it into a tutorial:
Sorry if this question was posted before (I did ask this in the NOOB-FRIENDLY thread, but didn't get a constructive answer)
My Xperia Neo V dropped into water.
Dried it with rice for a whole day and turned it on. Success! Was able to even play games.
Then I sent it for charging. (Battery was 8%)
5 mins later, it died.
Responds by entering flashmode after blinking red LEDs (3 I think), so I flashed stock.
Still couldn't start, so I sent it for charging (No response either after some hours)
I abandoned it and switched to a Galaxy Ace...until now....
Connected it to PC a month later.
It blinks red LED continuously, unplugged it and plugged it to a charger. No LED response whatsoever.
Plugged to PC again and POOF! Magic.
Detected by PC as my old MT11i :'D
LED is green, can do file exploration. Buttons are lit, vibrates when I press shutter button. No sound with the volume buttons
So the verdict...
CAN I STILL REVIVE MY NEO V?
IS MY DISPLAY DAMAGED?
This tutorial was made possible by @xange and @georgeiulian89. Thanks!
Usually when you drop your phone, you would be doomed. Or so you thought. With this tutorial, you can save A LOT of money buying a new phone or repairing the wet phone!
HOWEVER, I CANNOT GUARANTEE THAT YOUR PHONE CAN REVIVE. THIS WORKED FOR ME (SHALLOW DIP IN WATER). YOU MIGHT ALSO NEED A NEW BATTERY (IF YOU THINK YOU CAN REVIVE IT)
Steps(suggested by xange, proved):
1. Remove your phone from the water source IMMEDIATELY! (duh) DO NOT ATTEMPT TO SWITCH IT ON OR PRESS ANY BUTTON.
2.Remove the battery, SIM and micro SD cards.
3.Dry the body with a dry cloth. Try not to use tissue paper as it will leave residue.
4.Disassemble the phone, all the way to the motherboard. I used a small slotted screwdriver (the one with only one edge)as there are screws shaped like stars. If you have that type of screwdriver you can use it. Similar disassembly video here: www.youtube.com/watch?v=ginuDIeNCs8
WARNING: INTERNAL PARTS ARE VERY SENSITIVE TO STATIC, METAL,ETC. BE CAREFUL. ALSO REMOVE THE CONNECTIONS TO THE FRONT COVER AND DIGITIZER (display) BEFORE REMOVING THEM.
5.Direct a blowing fan to all the internal parts to dry them. Keep the screws and parts in an accessible area. Leave it for 30 minutes. DO NOT DRY IT WITH A HAIRDRYER. YOU ARE JUST TRYING TO SCREW YOUR PHONE.
6.Reassemble the phone and insert the battery ONLY. Then, switch on the phone. If not,
A) CHARGE IT: Your phone battery might be 100% dead(until normal charging can't power it on). For me I pressed and held the Back button while plugging the charger into the phone (Flashmode). The LED should blink red and eventually, green. This is when normal charging starts.
B) REPLACE THE BATTERY: You'll need to do so especially when the (once)white area near the connectors of the battery has turned red, indicating battery damage.
C) SEND IT TO A (optional: AUTHORIZED) SERVICE CENTER: Out of luck. This is the furthest I can help.
ALTERNATIVE DRYING METHODS:
A)PUT IT IN RICE FOR A DAY: NO, Asians won't come to repair your phone. Rice acts like silica, which absorbs moisture like sponge. I suggest you disassemble the phone first as rice might get into the small holes around your phone.
B)SOAK IN ALCOHOL, THEN PUT IT OUT: Disassemble it first, too. Though I haven't tried this method, there are those who have proved it to work.
C) RADIATOR DRYING (suggested by georgeiulian89): I've turned it off,i've removed the back cover, took out the battery, sim card and sd card, and i've put the phone on the radiator (i've put a towel between the phone and the radiator and i've placed the phone on the towel). I've left the phone about two hours to dry, and then i've inserted back the sim, sd card and the battery and turned it on.
C)DRY IT WITH A HAIRDRYER: NO. RISKY METHOD. Water will evaporate, then condense back somewhere once you've done hairdrying your phone it will condense back. I tried it and it condensed on my phone's camera lens. (It's a hairdryer, not a phonedryer!)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Hope this tutorial helps those out there whose phones have went swimming (or diving)
THANK ME IF I HELPED
Click to expand...
Click to collapse
add in: make sure the ribbon connector is clean before connected, if dust(or any tiny electric conductor) stick at connector while connecting them, you will have high chances to spoilt the phone.
Related
I have X10 that i bought from a friend. Last month i dropped it when i was on the beach. I Quickly remove the battery and wash it with clean water because i heard that salt water will damage my phone.then i leave it to air for about 2 days, I didn't dissasemble it because i was affraid. Then after 2 days i power up my phone then it backs to normal (there is some kind of water trace on the screen but everything works normal).
After about a week, i charged it but it won't charge at all. I have to remove the battery,put it back after 5 mins and recharge to do it. After about a month I was playing mp3 using headset and went to sleep but what i found on the morning is my phone turned off. I thought the battery has run out of power, I charged it but nothing happens,even the LED won't show a red light. I brought it to SE but they won't repair it because my friend bought this phone at hongkong not in my country. I decided to fix it my self,i tear down the phone and found that the cover of the ICs are rusty, not all of the cover but only some. I try to plugged in the charger to the micro usb slot on that teared down condition and what i found is the power management IC (qualcomm PM7540) got hot.
Could anybody help me?what should I do?
Did you stick it in uncooked rice. I did it when I dropped mine in sanitized water. Left it in for a full 24 hours and my x10 works like a charm. Try it. Just be careful to get ALL the rice out before powering it back up.
slyism3003 said:
Did you stick it in uncooked rice. I did it when I dropped mine in sanitized water. Left it in for a full 24 hours and my x10 works like a charm. Try it. Just be careful to get ALL the rice out before powering it back up.
Click to expand...
Click to collapse
thx for your reply,i have tried it last night.but only for a night because I'm sure that it is already dried ( I leave it to air for about a week ). Still it won't powered on,looks like short circuit problem. My friend told me that i should buy a new mainboard but it cost so damn high. I just want to know if there is another way to fix it.
Now, for this device already is late to help, but for the future, to other users such advice:
If your device visited salt water, then
1. Take off a back lid and battery
2. Carefully and repeatedly wash in the distilled water all parts
3. Dry up to the complete drying out at a temperature 40 С
so my phone got wet.. probably something was spilled over it or something...
anyway it shut down immediately (obvious)
i've opened the battery and pulled it out and i had water there.. i've dried it with a napkin as best as i could and power it on.. id didnt work
i've tried to plug it in the charger (probably shouldnt but was in panic heh) and i got the boot logo and the battery showed 5 precent.. i've waited a couple of minutes and it went up and up.. then i booted the phone... everything worked fine.. thought it was over and all was good.
then after 30 minutes or so i've unpluged the phone and after maybe 5 minutes it shut down (battery showed like 30 precent)
anyway.. i've then dried it some more with a hair drier but still the phone didnt boot
every time i connect the charger it shows 5% but doesnt move from it.. always on 5%..
When plugged in i can try to boot up but i see the M logo and after a few seconds it shuts down, nothing happens
I also can enter recovery or RSD or all the things...
What can i do?? is that the battery thats faulty? or the phone is gone? what can i try??
Well you have probably ended up frying something by turning it on while it was wet. I think you should let it dry out completely and then try to boot it up. If it still doesn't boot its a goner.
Google ways how to dry it. One way is to put it in a bag of rice for 2 days.
Sent from my MB860 running Jokersax's CM9
Towards the right of the SIM card, there is a whole in the plastic that has a moisture indicator spot, if that is white, then things are goodish, but if it is red??? then you may be in bad shape. Also, on the underside of the battery, there is another indicator, it should be mostly white with red + all over it, however if it is all red??? then the batter may be a goner. However, electronics these days are protected from some type of moisture, so it may just be still wet on the inside and may just need to be dried up.
To dry up electronics, as mentioned, a bag of dry rice is a great moisture sucker. Otherwise if you have an abundance of silica gel packets laying around, you can toss the phone into a container with those and let them sit for a few days.
However, you did you a hair drier, to that I say good luck. That kind of direct intense heat is horrible for most electronics, there is a very good chance you have destroyed some other internal component, and you probably won't be using your ATRIX any longer.
The issues you are running into are hardware related and the fact you can power on the phone at all surprises me. If you have a warranty plan that supports water damage, you can try reaching out to them and see what they want to do to help you, but considering you blasted a hair dryer at it, I would be very surprised.
take the battery, sim, sdcard, etc out and put in dry rice.
You plugged it into the charger, so game over imo. Whether it turns on or not you have damaged it. Better to cut your losses and look for a new phone. Done it myself.
Sent from my MB860 using xda premium
WiredPirate said:
take the battery, sim, sdcard, etc out and put in dry rice.
Click to expand...
Click to collapse
Its too late for that.
Sent from my MB860 using xda premium
Thanks for the replies.. An update for the situation..
I've waited more for the phone to dry and rest and then my girlfriend (her phone actually) started to mess with it and somehow turned it on and it actually works now.
The spot near the sim is white but the spot on the battery is totally red..
Now the strange thing is that the phone indicator shows that there is 5 percent left but when I looked at the battery voltage it showed 4196.. In the morning I checked the voltage and it was 4100 and the indicator showed 1%..
What's up with that??
Is the battery ruined? Or something else? Im going to buy a new one anyway but still...
Using neutrino 2.7 EE
You may have got lucky and just ruined the battery. Watch for corrosion on the connectors in the phone for battery, sim, and sdcard. That may be the next problem if a new battery works out.
Sent from my MB860 using xda premium
I dropped my phone in water for maximum 5-6 seconds. I pulled the battery out, dried it with a towel then ...(later i realize it was stupid) tried to turn it back on. It just did a fast boot loop without even pressing the power button. It's like the power button was stuck?
Then i read the online guides about the rice. So i put the phone in a rice container for 12 hours. I took it out and turned it on (using the power button). This time, it actually turned on, loaded up the KISS screen (I'm using ICS KISS) then it would just reboot to Vibrant again.
I also tried vol + and got download mode but when i did vol - i did not get recovery
Turned it off, put it back into the rice. Hoping things might change. Got a backup phone for the time being.
Question is... Can I simply flash the phone to stock or is a component linked to the main SDCard corrupted?
Thanks for the help!
Hello there! Are you comfortable with talking the phone apart? If so (only if you are), i myself would take out the battery asap with no power connect to the device. Then i would simply take it apart and leave it in parts to let dry. I would also look around for possible corrosion around soldered connections. If corrosion (usually white powdery looking kinda like a battery terminal in a car), i would take rubbing alcohol and a tooth brush and scrub it away. Then let it sit and let dry. Once dried out reassemble and insure that the connection ribbons are very securely in place. Sometimes when a phone is dropped and starts to boot loop, it just means a connector isn't all the way connected anymore. But considering that water is in the picture, it could be a combination. By the way this is at your own risk and this is what i would personally do and have done with success. Ive seen phones with plenty of water still in them after the rice thing. I hope this helps you out man. Good luck and if you do choose to take apart your phone just take your time and be careful. I would only take out the main board and the board that connects to it and not worry about anything else that isn't a board. Sorry for the book lol.
Sent from my SAMSUNG-SGH-I717 using XDA
If you Google "how to install front faced camera vibrant mobiletech video", watch the youtube video because they take apart the back of the phone. It not as hard as you think. Then put it in a bag if rice like the above post said. Good luck!
Sent from my SGH-T959 using xda premium
So, to start this off my rezound fell into a pool with me. Rushed and did the usual steps for drying it out and all that. The battery was the only thing that took water damage according to the sensor. So I bought a new one and it won't charge the battery. The one time I got the phone on it read 0% charged after sitting for 6 hours. Now it's either blinking orange or staying orange for around 5 seconds. Is there anything I can do?
DincWeeman said:
So, to start this off my rezound fell into a pool with me. Rushed and did the usual steps for drying it out and all that. The battery was the only thing that took water damage according to the sensor. So I bought a new one and it won't charge the battery. The one time I got the phone on it read 0% charged after sitting for 6 hours. Now it's either blinking orange or staying orange for around 5 seconds. Is there anything I can do?
Click to expand...
Click to collapse
Sounds like your phone is damaged, the old battery was probably fine, the water indicator is there to let Verizon know the phone had water damage when people try to warranty them...
I'd throw it in a bag of rice a little longer, see if there's any more moisture stuck in it, otherwise it's time for a new phone...
I had a similar situation, minus the water, but you might try pulling the battery out and charging it manually with a power supply set to supply 5 V and current limited to 1 A. Let it charge like that for 20 min and try putting it in the phone again. If it still will not work, then it could be that the leads on the phone that connect to the battery are corroded and need to be cleaned.
swilbert80 said:
I had a similar situation, minus the water, but you might try pulling the battery out and charging it manually with a power supply set to supply 5 V and current limited to 1 A. Let it charge like that for 20 min and try putting it in the phone again. If it still will not work, then it could be that the leads on the phone that connect to the battery are corroded and need to be cleaned.
Click to expand...
Click to collapse
How would I go about doing this?
DincWeeman said:
How would I go about doing this?
Click to expand...
Click to collapse
I take that to mean you don't have access to a variable voltage power supply. Not a problem, but it would help if you at least have access to a voltmeter or multimeter. You would need to plug in your charger with cable and test each of the leads to see which two have 5 V across them. Then attach wires to both and the other end of each wire to the positive and negative leads on the battery itself. I would use a different cable (not micro-usb) so that the leads are larger and easier to access. If you cannot do this, then you could use a stand-alone battery charger like this:
http://www.verizonwireless.com/b2c/...peId=12852&accessoryId=48042&initialPhoneId=0
But that would require you to buy one, which may be a waste if the phone is actually the problem. But if you do buy it and it turns out the phone is the problem, you could keep the receipt and get a refund.
As far as clean the leads on the phone, you could try mixing baking soda and water (little water) into a thick paste and scrubbing with a tooth brush. The paste will need to sit on the metal leads for some time (30 mins to 2 hours depending). Then use isopropyl alcohol (rubbing alcohol) on tissue to clean any remaining garbage/residue. Then you will need to let it dry again, ideally in a sealed container with silica or rice. I would probably leave it in there for at least 24 hours.
If both of these don't fix the problem, then you probably have either shorted some internal circuitry or have some other corrosion inside the phone somewhere.
Well I really can't try that suggestion broke college student and all. Thanks though.
You can get this external charger cheap. I have it, works fine:
http://www.amazon.com/gp/product/B0054U58OY/ref=oh_details_o02_s00_i00?ie=UTF8&psc=1
Here's a battery to go with it:
http://www.amazon.com/gp/product/B0079Q67IC/ref=oh_details_o03_s00_i00?ie=UTF8&psc=1
Note to self check amazon before ebay. This one should work too right?: http://www.ebay.com/itm/400429190799?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
Water got into my phone(obviously) and I tried turning it on because of water resistance. It didn't respond. So I tried charging it. Tell my why the phone's battery screen flashed? NVM that, I tried the ol' bag full of rice trick. I left it there for about 12 hours. I tried again, and I got into recovery, but with a reddish tint. Well, I tried re-installing my ROM, hoping that it was an easily fixable issue. When the rom was installing, I unplugged my phone, instant power off. And my phone was at 100% before the install. I panicked, and knowing that I had to use my phone soon, I did probably the stupidest move ever, and put it on AN ELECTRIC HEATER. I left it there for 5 minutes, because that heater gets so hot that the air in my whole house is dry after ~30 minutes. Now sometimes when I turn it on, if the charger isn't in, the apps initialize, then power off, other times I get nothing. If I put the charger in, I sometimes get a white-ish triangle with a red thermometer(I'm guessing temperature warning?) and sometimes the battery flashes periodically. Please help, because of family health problems I need to be able to use my phone.
EDIT***: Phone WILL turn on now, condensation on both cameras, and battery temp too low to charge, so now there's a broken thermometer.
GG3K said:
Water got into my phone(obviously) and I tried turning it on because of water resistance. It didn't respond. So I tried charging it. Tell my why the phone's battery screen flashed? NVM that, I tried the ol' bag full of rice trick. I left it there for about 12 hours. I tried again, and I got into recovery, but with a reddish tint. Well, I tried re-installing my ROM, hoping that it was an easily fixable issue. When the rom was installing, I unplugged my phone, instant power off. And my phone was at 100% before the install. I panicked, and knowing that I had to use my phone soon, I did probably the stupidest move ever, and put it on AN ELECTRIC HEATER. I left it there for 5 minutes, because that heater gets so hot that the air in my whole house is dry after ~30 minutes. Now sometimes when I turn it on, if the charger isn't in, the apps initialize, then power off, other times I get nothing. If I put the charger in, I sometimes get a white-ish triangle with a red thermometer(I'm guessing temperature warning?) and sometimes the battery flashes periodically. Please help, because of family health problems I need to be able to use my phone.
EDIT***: Phone WILL turn on now, condensation on both cameras, and battery temp too low to charge, so now there's a broken thermometer.
Click to expand...
Click to collapse
This phone is not water resitant. So trying to turn it on, before it dried completely was not that great of an idea. You could still have someone disassemble it, clean the board in alcohol and replace the battery. I think you just overheated the battery and you might have several shorts on your "mainboard". So please stop using it, until someone cleaned the board at least in some isopropanole or even better isoprop in an ultrasonic device. Dont just throw it in completely, but the "mainboard" only.
Sent from my SM-G925F using XDA Free mobile app