How to root - recovery - rom - Samsung Galaxy Mega

Hey folks,
I have quite some experience with rooting etc, but I don't know how to work with odin.
Could someone provide some kind of guide that will help to install a custom recovery? Via odin
Thanks!
Sent from my GT-I9205 using XDA Premium 4 mobile app

Here is info on that i had saved for a while now, and this works the same way for flashing recoveries also.
Before Flashing A ROM or .TAR file via ODIN
First, download the latest version of ODIN you can find. i use odin 3.07 which works great
Install ODIN on your computer.
Make sure that your phone's drivers are installed in your computer. If you connect your phone to the computer (and it doesn't have drivers), your computer will find and install them for you. Happened to all Samsung Galaxy devices.
Turn on USB Debugging Mode in your phone by going to Settings > More > Developer options > and check USB debugging box, and if this selection is not shown go to About phone under the More tab still and go down to Build number and tap it 7 times and then it will say developers option is now available or something like that and then go back to Settings > More and you should then see the selection for Developer options.
Make sure that your battery is fully charged or at least 50% charged.
Flashing A ROM or .TAR file via ODIN
Launch ODIN on your computer. Just allow it if your computer asks for permission. Mine does every time.
Unzip the ROM you downloaded (usually a .rar file). It might contain 3 .md5 files, just 1 .md5 file and sometimes, an additional .pit file.
Golden rule: Don't mess with the presets ever. Example, if re-partition is unticked, DO NOT TICK IT. The only time it gets ticked is when you upload a .pit file on the PIT box. If it does, leave it that way. ODIN TICKED IT FOR A REASON. Let ODIN do its job.
See bottom of post for guide on where to place files on ODIN.
Connect your phone to the computer using a USB cable. The box on the upper left corner of ODIN should turn yellow (depending on what version of odin) and the message "Added!" should be on display.
Click "Start" and wait for the box on the upper left to turn green and say "PASS!"
Your phone should auto-reboot after that and presto, you now have a squeaky new ROM/Recovery to play with and you can then disconnect the usb cable now.
Where To Place Files On ODIN
pit file ---> PIT box
If there is just one .md5 file or .tar file, no matter the label place in ---> PDA box
If there are three .md5 files:
file containing "CODE" ---> PDA box
file containing "MODEM" ---> Phone box
file containing "CSC" ---> CSC box
Hope this helps you out.

starmaster10 said:
Here is info on that i had saved for a while now, and this works the same way for flashing recoveries also.
Before Flashing A ROM via ODIN
First, download the latest version of ODIN you can find. i use odin 3.0.7 which works great
Install ODIN on your computer.
Make sure that your phone's drivers are installed in your computer. If you connect your phone to the computer (and it doesn't have drivers), your computer will find and install them for you. Happened to all Samsung Galaxy devices.
Turn on USB Debugging Mode in your phone by going to Settings > Applications > Development > check USB debugging.
Make sure that your battery is fully charged or at least 50% charged.
Flashing A ROM via ODIN
Launch ODIN on your computer. Just allow it if your computer asks for permission. Mine does every time.
Unzip the ROM you downloaded (usually a .rar file). It might contain 3 .md5 files, just 1 .md5 file and sometimes, an additional .pit file.
Golden rule: Don't mess with the presets ever. Example, if re-partition is unticked, DO NOT TICK IT. The only time it gets ticked is when you upload a .pit file on the PIT box. If it does, leave it that way. ODIN TICKED IT FOR A REASON. Let ODIN do its job.
See bottom of post for guide on where to place files on ODIN.
Connect your phone to the computer using a USB cable. The box on the upper left corner of ODIN should turn yellow (depending on what version of odin) and the message "Added!" should be on display.
Click "Start" and wait for the box on the upper left to turn green and say "PASS!"
Your phone should auto-reboot after that and presto, you now have a squeaky new ROM/Recovery to play with and you can then disconnect the usb cable now.
Where To Place Files On ODIN
pit file ---> PIT box
If there is just one .md5 file, no matter the label place in ---> PDA box
If there are three .md5 files:
file containing "CODE" ---> PDA box
file containing "MODEM" ---> Phone box
file containing "CSC" ---> CSC box
Hope this helps you out.
Click to expand...
Click to collapse
Hi! Thanks a ton for this extensive post!! I still have one question, with my note n7000 I downloaded a stock rom from Sammobile and got a tar.md5 file. Do I get the same files from Sammobile for the I9205? If so, where do I place this file in odin? Also in PDA?
Sent from my GT-I9205 using XDA Premium 4 mobile app

Thatgrass said:
Hi! Thanks a ton for this extensive post!! I still have one question, with my note n7000 I downloaded a stock rom from Sammobile and got a tar.md5 file. Do I get the same files from Sammobile for the I9205? If so, where do I place this file in odin? Also in PDA?
Sent from my GT-I9205 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Yep you put the file in the PDA window also. :good:

starmaster10 said:
Yep you put the file in the PDA window also. :good:
Click to expand...
Click to collapse
And flashing for (Silesh.Niar's TWRP with kitkat support) recoveries? Also in the PDA I guess?

Thatgrass said:
And flashing for (Silesh.Niar's TWRP with kitkat support) recoveries? Also in the PDA I guess?
Click to expand...
Click to collapse
Yes in PDA window also. :good:

Related

Possible Brick. How can i make download mode work?

Samsung wont boot past VIBRANT screen.
I have access to both Download mode and recovery mode.
In recovery i have stock recovery and when i try to put ClockWordmod via reinstall packages it just restarts to recovery mode.
I have access to download mode but my computer doesnt prompt me and there is no icon for my samsung galaxy s in "devices with removable storage"
I want to flash Odin or Bionix on top of it, but i dont seem to have the option.
Any one help?
Update:
It previously had Bionix 1.7 , but when i tried installing Bionix 1.8 the case along with the battery fell.
So it does not boot up
So you can get your phone into Download mode? (Yellow Triangle with an android digging and the words "Downloading, do not turn off target"?)
yeah the yellow icon does not install what ever drivers are needed for my Windows 7 to know im connnected. i do get a sound though
Does anyone have any ideas???
This thread contains drivers, and everything you'll need to get odin working. Before doing anything make sure you read up on ODIN. Just take a deep breath, and don't rush anything or you'll screw up your phone. Read, then read some more, then triple check. Make sure you have drivers installed, odin, tar file (rom), pit file, and patience.
http://ip208-100-42-21.static.xda-developers.com/showthread.php?t=803492
Thanks Paging I am trying it right now. I'll tell you how it went. Been stuck for a while on Set PIT.
Paging Dr B said:
This thread contains drivers, and everything you'll need to get odin working. Before doing anything make sure you read up on ODIN. Just take a deep breath, and don't rush anything or you'll screw up your phone. Read, then read some more, then triple check. Make sure you have drivers installed, odin, tar file (rom), pit file, and patience.
http://ip208-100-42-21.static.xda-developers.com/showthread.php?t=803492
Click to expand...
Click to collapse
Best advice this century!
xallies said:
I have access to download mode but my computer doesnt prompt me and there is no icon for my samsung galaxy s in "devices with removable storage"
Click to expand...
Click to collapse
It won't show up as a device with removable storage when it's in Download Mode. If it's working properly it will show up on a COM port in Odin (in a yellow box toward the top left).

ICS 4.0.4 Update

Try this step by step and it should work!
Requirements
A Samsung Galaxy S2 GT-I9100
A Windows PC
Your phone’s USB cable
7-Zip, WinRAR, or any other programs that can extract archive files
Handset USB drivers installed on the PC. You may install the drivers by installing Samsung Kies.
Enable USB Debugging on your handset.
Disable antivirus, firewall, and other security software. Also disable Samsung Kies and other software that accesses
your phone. Such software can interfere with the procedure in this guide.
Download the following files to your computer:
Android 4.0.4 ICS firmware build XXLQ5 (I9100XXLQ5_I9100OXALQ5_OXA.zip, 387.1 MB)
copy and paste
hotfile.com/dl/162208594/226b6f0/I9100XXLQ5_I9100OXALQ5_OXA.zip.html
Odin3 1.85 (Odin 1.85.zip,199 kB)
Make sure your phone’s battery is charged up to 75% or more to avoid interruptions during the process.
Backup all personal data on your phone to make sure you have a copy of your personal data (e.g., contacts, SMS, MMS,
Internet settings, Wi-Fi passwords, and the like) in case the procedure in this guide erases such data.
For backup tips, check our guides on how to sync your data to the cloud and how to create local backups of your
mobile data.
Instructions
Extract the contents of the I9100XXLQ5_I9100OXALQ5_OXA.zip file to get these files:
I9100_CODE_I9100XXLQ5_CL753921_REV02_user_low_ship.tar.md5
GT-I9100-MULTI-CSC-OXALQ5.tar.md5
MODEM_I9100XXLQ5_REV_02_CL1165929.tar.md5
u1_02_20120326_emmc_EXT4_8GB.pit
Extract the contents of the Odin 1.85.zip file to obtain the Odin3 v1.85.exe file.
Double-click on the Odin3 v1.85.exe file to launch Odin on your computer.
Unplug your phone from the computer if it is connected. After unplugging, turn your phone off.
Put your phone into Download Mode. To do this, hold the Volume Down, Home, and Power buttons together until the
screen turns on. Press the Volume Up key to put your phone into Download Mode.
Connect your phone to the PC using the USB cable. In Odin, a message saying “Added!!” will appear on the bottom left
of the window.
In the Odin window, click on the PDA button and select the
I9100_CODE_I9100XXLQ5_CL753921_REV02_user_low_ship.tar.md5file. The file should show on the space beside the PDA
button.
Click on the PHONE button and select MODEM_I9100XXLQ5_REV_02_CL1165929.tar.md5 file. The file should show on the
space beside the Phone button.
Click on the CSC button and select the GT-I9100-MULTI-CSC-OXALQ5.tar.md5file. The file should show on the space
beside the CSC button.
Don’t alter anything else in Odin. Leave everything else as is, except for adding the files mentioned in steps 7 to
9.
Click on the Start button in Odin to start flashing the firmware to your phone.
After the flashing completes, your phone will automatically reboot. You should be able to get a “PASS” message on
the top left part of Odin.
NOTE: If you get a FAIL message or Odin gets stuck, disconnect your phone from the PC and close Odin. Remove the
battery from your phone, re-insert it, and place your phone into Download Mode again. Open Odin and do the procedure
starting from step 6.
Once you see the Samsung logo on your phone’s screen, you can safely disconnect your phone from the PC.
Hope this helps!
ScottsDesk
What is the meaning of this?
Jokesy said:
What is the meaning of this?
Click to expand...
Click to collapse
Its a ICS 4.0.4 update I found that I thought I would share. This is the place to do that right?
Scott
Emm... but there such guides already are in General / Original Android Development.
So, you have just worked unnecessarily.
przemcio510 said:
Emm... but there such guides already are in General / Original Android Development.
So, you have just worked unnecessarily.
Click to expand...
Click to collapse
Such is the story of my life...lol
ScottsDesk
when extracting them it show me brocken files. can u fix that?
mahmoudsalem91 said:
when extracting them it show me brocken files. can u fix that?
Click to expand...
Click to collapse
There are enough guides in xda. Just read and you probably can solve this

How to UNBRICK Samsung Showcase on NTELOS!?

Ok thanks to my friend lending me his Bricked phone i was able to Unbrick his phone for his. Heres what you need to do!
****I TAKE NO RESPONSIBILITY IF YOUR PHONE WORSENS OR ENTERS A PERMANENT BRICK****
****TAKE CAUTION AND REALIZE THAT YOU ARE THE ONE PERFORMING THESE DIRECTIONS****
1.Have Odin installed and download that file from the link http://db.tt/VJzi0DNk
2.Extract the Files into a Folder on the home screen of your Computer
3.Fire Up and Prep Odin
4.In the OPTIONS check Auto Reboot and F.Reset Time
5.In PIT place the pit file extracted from the ZIP you downloaded from the link above by browsing to the Folder that you extracted the files to
6.In PDA repeat the directions from #5 EXCEPT place the Tar. File instead
7.Power off the Samsung Showcase and connect the microUSB to the computer but not the Samsung Showcase.
8.Boot YOUR Samsung Showcase into download mode BY holding down Volume Down while connecting the MicroUSB cable to YOUR Samsung Showcase.
9.When ODIN says Added Click start and leave the Phone alone.
10.Once it says DONE or your Phone has Reboot You are Finished
****I TAKE NO RESPONSIBILITY IF YOUR PHONE WORSENS OR ENTERS A PERMANENT BRICK***
**Please Thumbs Up if i Helped**
*****UPDATE 10.26.12*****No 3G Working on NTELOS...trying to find solution but, If you don't care about that then go ahead and sign to wifi

[Q] Samsung S3 mini i8200L - Hard Bricked

Hi All,
Need some help. My Samsung S3 mini i2800L was flashed with the wrong firmware in an attempt to upgrade to Jellybean 4.2.2 using odin and it failed . It remained in download mode and I did a battery pull ,now the phone is absolutely dead. Black Screen for all the following:Recovery Mode and Download Mode .The phone wont power on at all. The only sign of life , is when I plugged into my girl friend's Toshiba laptop via usb cable and it searched and installed the drivers.In addition Windows makes a sound when the device is plugged in and unplugged, but is not being recognized by Kies or Odin. I also tried a USB JIG with no success.
Is there any debrick file that I can use for to place on my SD card and attempt to boot from SD, or is JTAG the only option left?
yes!!! you can UNBrick it!!!
OK ... good news for you is it can still be read by the comp when connected (prompts by audio signal) ... it wont take more than 2 min to unbrick your phone... tell me have if you have a stock ROM available for your device?
unbrick Samsung galaxy s3 mini
omkarfrozen said:
OK ... good news for you is it can still be read by the comp when connected (prompts by audio signal) ... it wont take more than 2 min to unbrick your phone... tell me have if you have a stock ROM available for your device?
Click to expand...
Click to collapse
Yes I have downloaded a stock ROM from the internet that can be used. My phone is unlocked so I just downloaded a open firmware , please guide me on the steps required and thanks for responding BTW.
Leon bernard said:
Yes I have downloaded a stock ROM from the internet that can be used. My phone is unlocked so I just downloaded a open firmware , please guide me on the steps required and thanks for responding BTW.
Click to expand...
Click to collapse
have you downloaded SP flash tool along with it??? if not then search for that tool on needrom website... now turn off your phone by removing the battery... now open the SP flash tool and select the Scatter-Loading file present in your stock ROM folder... now click download button... then quickly connect your phone via USB... wait for 5 min ... you will get a message box with green circle and you are done!!! use your phone as you used to earlier...
will try it
omkarfrozen said:
have you downloaded SP flash tool along with it??? if not then search for that tool on needrom website... now turn off your phone by removing the battery... now open the SP flash tool and select the Scatter-Loading file present in your stock ROM folder... now click download button... then quickly connect your phone via USB... wait for 5 min ... you will get a message box with green circle and you are done!!! use your phone as you used to earlier...
Click to expand...
Click to collapse
Wow. Im going to try this when I reach home from work today, I will let you know if it works. Thanks a million
how to access scatter loading file
Leon bernard said:
Wow. Im going to try this when I reach home from work today, I will let you know if it works. Thanks a million
Click to expand...
Click to collapse
Hi ,
So I have the stock rom but its in md.5 format so I cant access the directories. Is their anyway I can convert it so I can access the scatter loading file ?
omkarfrozen said:
have you downloaded SP flash tool along with it??? if not then search for that tool on needrom website... now turn off your phone by removing the battery... now open the SP flash tool and select the Scatter-Loading file present in your stock ROM folder... now click download button... then quickly connect your phone via USB... wait for 5 min ... you will get a message box with green circle and you are done!!! use your phone as you used to earlier...
Click to expand...
Click to collapse
Hi ,
So I have the stock rom but its in md.5 format so I cant access the directories. Is their anyway I can convert it so I can access the scatter loading file ?
Leon bernard said:
Hi ,
So I have the stock rom but its in md.5 format so I cant access the directories. Is their anyway I can convert it so I can access the scatter loading file ?
Click to expand...
Click to collapse
OK if you have stock ROM in md5 then follow these steps
1) copy the md5 file on desktop
2. Download Odin 3.07
3. Switch off your phone and boot Galaxy S3 Mini I8200L into Download
Mode by pressing and holding the Volume Down+Home+Power buttons
(long press until the boot screen appear), now press Volume Up key to
proceed to Download Mode .IN CASE IT doesn't WORK TRY EVERY COMBINATION SO AS TO ACHIEVE 6TH STEP... IF NOTHING WORKS THEN JUST CONNECT THE PHONE WITHOUT PRESSING ANY COMBINATIONS...
4. Extract the downloaded Odin3.07 zip file and run the Odin3 v3.07.exe
file as an administrator (Right click on the .exe file and click on Run as
administrator)
5. Now connect your Galaxy S3 Mini I8200L to your computer via USB
cable
6. In Odin3 screen, you should see a COM Port number like “0:[COM7]” at
ID:COM section and “Added!” text at the message box. This means your
device has been detected by Odin3.
7. Make sure that, only the “Auto Reboot” and “F. Reset Time” options are
checked.
8. Now, extract the downloaded firmware .zip file, you’ll find a firmware file
with extension .tar.md5
9. In Odin screen, click on PDA button and select the firmware file with
.tar.md5 extension (The firmware file look something like:
I8200LXXDLJ5_I8200LODDDLI7_INU.tar.md5)
10. Now, click on the Start button to begin the installation process, wait few
moments.
11. Once completed, you would see “PASS!” message in ID:COM port having
green background
12. Your phone should automatically reboot after completion
13. You can now disconnect your phone from computer
14. Finish.
omkarfrozen said:
OK if you have stock ROM in md5 then follow these steps
1) copy the md5 file on desktop
2. Download Odin 3.07
3. Switch off your phone and boot Galaxy S3 Mini I8200L into Download
Mode by pressing and holding the Volume Down+Home+Power buttons
(long press until the boot screen appear), now press Volume Up key to
proceed to Download Mode .IN CASE IT doesn't WORK TRY EVERY COMBINATION SO AS TO ACHIEVE 6TH STEP... IF NOTHING WORKS THEN JUST CONNECT THE PHONE WITHOUT PRESSING ANY COMBINATIONS...
4. Extract the downloaded Odin3.07 zip file and run the Odin3 v3.07.exe
file as an administrator (Right click on the .exe file and click on Run as
administrator)
5. Now connect your Galaxy S3 Mini I8200L to your computer via USB
cable
6. In Odin3 screen, you should see a COM Port number like “0:[COM7]” at
ID:COM section and “Added!” text at the message box. This means your
device has been detected by Odin3.
7. Make sure that, only the “Auto Reboot” and “F. Reset Time” options are
checked.
8. Now, extract the downloaded firmware .zip file, you’ll find a firmware file
with extension .tar.md5
9. In Odin screen, click on PDA button and select the firmware file with
.tar.md5 extension (The firmware file look something like:
I8200LXXDLJ5_I8200LODDDLI7_INU.tar.md5)
10. Now, click on the Start button to begin the installation process, wait few
moments.
11. Once completed, you would see “PASS!” message in ID:COM port having
green background
12. Your phone should automatically reboot after completion
13. You can now disconnect your phone from computer
14. Finish.
Click to expand...
Click to collapse
Sigh , unfortunately odin is not detecting my phone at all. Remember that the phone is completely dead, which means it cant power on or go any mode . I think the SP Flash tool would work but I need the scatter file
Leon bernard said:
Sigh , unfortunately odin is not detecting my phone at all. Remember that the phone is completely dead, which means it cant power on or go any mode . I think the SP Flash tool would work but I need the scatter file
Click to expand...
Click to collapse
Download Samsung mobile drivers... Because you had said your friends laptopts prompts when you connect your mobile to his laptop. So remember 1thñg your phone is not completely dead yet. try if flash ROM from his laptop
omkarfrozen said:
Download Samsung mobile drivers... Because you had said your friends laptopts prompts when you connect your mobile to his laptop. So remember 1thñg your phone is not completely dead yet. try if flash ROM from his laptop
Click to expand...
Click to collapse
Ok so update: I downloaded Keis and installed all drivers. I recognized now that the phone is connecting as EMEI on PC. I clicked on it uninstall the drivers and re install it , but ODIN nor Keis still does not recognize phone , only computer recognizes phone as EMEI. Let me know your views.
Leon bernard said:
Ok so update: I downloaded Keis and installed all drivers. I recognized now that the phone is connecting as EMEI on PC. I clicked on it uninstall the drivers and re install it , but ODIN nor Keis still does not recognize phone , only computer recognizes phone as EMEI. Let me know your views.
Click to expand...
Click to collapse
get your Samsung usb drivers from here developer.samsung .com /board/download.do?bdId=0000000700&attachId=0000000001 (remove the spaces in between). give me some time so that I can find scatter file for your phone.
omkarfrozen said:
get your Samsung usb drivers from here developer.samsung .com /board/download.do?bdId=0000000700&attachId=0000000001 (remove the spaces in between). give me some time so that I can find scatter file for your phone.
Click to expand...
Click to collapse
drivers downloaded and installed. I await the scatter file. thanks for your efforts .
Leon bernard said:
Hi All,
Need some help. My Samsung S3 mini i2800L was flashed with the wrong firmware in an attempt to upgrade to Jellybean 4.2.2 using odin and it failed . It remained in download mode and I did a battery pull ,now the phone is absolutely dead. Black Screen for all the following:Recovery Mode and Download Mode .The phone wont power on at all. The only sign of life , is when I plugged into my girl friend's Toshiba laptop via usb cable and it searched and installed the drivers.In addition Windows makes a sound when the device is plugged in and unplugged, but is not being recognized by Kies or Odin. I also tried a USB JIG with no success.
Is there any debrick file that I can use for to place on my SD card and attempt to boot from SD, or is JTAG the only option left?
Click to expand...
Click to collapse
follow this brick
Help me too
Leon bernard said:
drivers downloaded and installed. I await the scatter file. thanks for your efforts .
Click to expand...
Click to collapse
I got the exact same issue.. my phone is samsung galaxy s3 mini. i will be very happy if you would also find the scatter file (although i still have no idea what is that) for my phone too, while i google it. i'm newbie, i'm not really sure what to find.. help me.. :crying:
tebegaya said:
I got the exact same issue.. my phone is samsung galaxy s3 mini. i will be very happy if you would also find the scatter file (although i still have no idea what is that) for my phone too, while i google it. i'm newbie, i'm not really sure what to find.. help me.. :crying:
Click to expand...
Click to collapse
Hey guys am using samsung s3 mini GT I8190, i recently flashed cyanogenmode 5.1.1 on my device, it was working fine but i decided to do a nandroid back up and in the process my phone died. it cannot power on or go to downloading mode. When i connect to my laptop there is a sound that its connected but then it disconnects help please..
omkarfrozen said:
OK if you have stock ROM in md5 then follow these steps
1) copy the md5 file on desktop
2. Download Odin 3.07
3. Switch off your phone and boot Galaxy S3 Mini I8200L into Download
Mode by pressing and holding the Volume Down+Home+Power buttons
(long press until the boot screen appear), now press Volume Up key to
proceed to Download Mode .IN CASE IT doesn't WORK TRY EVERY COMBINATION SO AS TO ACHIEVE 6TH STEP... IF NOTHING WORKS THEN JUST CONNECT THE PHONE WITHOUT PRESSING ANY COMBINATIONS...
4. Extract the downloaded Odin3.07 zip file and run the Odin3 v3.07.exe
file as an administrator (Right click on the .exe file and click on Run as
administrator)
5. Now connect your Galaxy S3 Mini I8200L to your computer via USB
cable
6. In Odin3 screen, you should see a COM Port number like “0:[COM7]” at
ID:COM section and “Added!” text at the message box. This means your
device has been detected by Odin3.
7. Make sure that, only the “Auto Reboot” and “F. Reset Time” options are
checked.
8. Now, extract the downloaded firmware .zip file, you’ll find a firmware file
with extension .tar.md5
9. In Odin screen, click on PDA button and select the firmware file with
.tar.md5 extension (The firmware file look something like:
I8200LXXDLJ5_I8200LODDDLI7_INU.tar.md5)
10. Now, click on the Start button to begin the installation process, wait few
moments.
11. Once completed, you would see “PASS!” message in ID:COM port having
green background
12. Your phone should automatically reboot after completion
13. You can now disconnect your phone from computer
14. Finish.
Click to expand...
Click to collapse
Hello, i need some help. I have tried all but always shows faild...i even use a recovery.tar and the bar goes all the way to the end but when the procces its almost finish it shows FAIL.
What can i do?
I do have the firmwarew file and it does not work, thx

Samsung Galaxy S3 (GT-I9300) Problem Odin firmware recovery

Hi,
Sorry my englihs!
I have one big problem. I must use odin program because my phone not start (screen is allways gray line) but when I start Odin download mode then screen working perfect!
When I tried recovery firmware using Odin 3.09 appear message "There is no PIT partition". Where I can give it? I live in Finland and I tried put my phone firmware NEE-I9300XXUGND5.
Anybody can help?
Did you try different USB cables and USB 2.0 ports? Try Odin 3.07. When flashing with Odin, do not check anything except auto reboot and f reset time.
tormso said:
Hi,
Sorry my englihs!
I have one big problem. I must use odin program because my phone not start (screen is allways gray line) but when I start Odin download mode then screen working perfect!
When I tried recovery firmware using Odin 3.09 appear message "There is no PIT partition". Where I can give it? I live in Finland and I tried put my phone firmware NEE-I9300XXUGND5.
Anybody can help?
Click to expand...
Click to collapse
Untick "re-partition". As audit says. Only reboot, reset time and "one package" should be ticked. You apply the firmware in the "PDA" radio buttion and click start.
Beamed in by telepathy.
audit13 said:
Did you try different USB cables and USB 2.0 ports? Try Odin 3.07. When flashing with Odin, do not check anything except auto reboot and f reset time.
Click to expand...
Click to collapse
shivadow said:
Untick "re-partition". As audit says. Only reboot, reset time and "one package" should be ticked. You apply the firmware in the "PDA" radio buttion and click start.
Beamed in by telepathy.
Click to expand...
Click to collapse
audit13, yes I tried many USB cables and Odin 3.07.
shivadow, I tried same options but I keep same problems. Can I use wrong "PDA" files?
This is my options and problems.
imgur.com/a/H85or
Thanks!
You are doing it correctly. If the firmware is definitely the correct one for your phone and you know for a fact the usb cable is good then the phone is bricked.
There is a very slight chance that flashing a .pit file "could" revive your phone but at this point I think it is beyond repair.
Time to find the correct .pit file and flash it but expect it to not work, anything else is a bonus.
Beamed in by telepathy.
Sounds like a hardware problem to me. Download mode does not use or stress the gpu. Once the ROM starts to boot, the GPU is used.
Was the phone dropped?

Categories

Resources