hey guys, im new to the site and need some help with the data cable of my transformer prime.
okay so the issue is that the original cable that was supplied with the tablet broke ( from the usb end of the cable no the 40 pin connector).
i bought a seperate usb 3.0 cable to replace that one and after a couple of weeks the cable gave up on me. this time it was the 40 pin connector that was broken.
i have stripped both the original and the new 3.0 wires and i was wondering if i could merge the two together to make one cable.
i have red, orange, yellow, green, white and a bare wire (which im guessing is the ground) on the original cable and black, white, green, red and a bare cable on the usb 3.0 cable. is it possible to solder the cables together and if yes which color goes with which. or do i just need to get a new cable?
thanks,
khan92 said:
hey guys, im new to the site and need some help with the data cable of my transformer prime.
okay so the issue is that the original cable that was supplied with the tablet broke ( from the usb end of the cable no the 40 pin connector).
i bought a seperate usb 3.0 cable to replace that one and after a couple of weeks the cable gave up on me. this time it was the 40 pin connector that was broken.
i have stripped both the original and the new 3.0 wires and i was wondering if i could merge the two together to make one cable.
i have red, orange, yellow, green, white and a bare wire (which im guessing is the ground) on the original cable and black, white, green, red and a bare cable on the usb 3.0 cable. is it possible to solder the cables together and if yes which color goes with which. or do i just need to get a new cable?
thanks,
Click to expand...
Click to collapse
Good luck getting support in this forum.. lol
Its pretty dead.. I would suggest trying the other TF Forums.. like the TF201 and higher.. They still use the same cables and basic chargers..
Youtube in this case is your friend...
This forum is still fairly active IMO, but regardless, this is not the TF201 forum
http://forum.xda-developers.com/transformer-prime
http://www.amazon.com/Extended-Char...d_sim_e_4?ie=UTF8&refRID=0JN64FK4AER92QVV958K
Related
I have one question, does miniusb cable will fit with this device or need special cable ?
the blueangel has a special port, there are adapters for notebook chargers, which covers a AC-supply generalisation, but there is no standard usb cable to use. i recently got a universal and i have to say i love the mini-usb port, since you can use all new htc accessories and everything you got lying around, i actually sync my device with a cable that came with a card reader, all that, unfortunately, is not possible with the ba
I realised this yesterday after 23:58 Very bad - i don't know where to find original cable or some connector pinout. Even my siemens unlocking cable don't work.
Nothing, phone will stay with german rom, wm2003. Even flashing via sd card not possible
Blue Angel usb cables can easily be found online if you look for them I purchased a couple for 10 dollars or less.
They tended to come with a USB docking station, this is what you'd use to sync it to a computer.
I am selling one, but postage could be an issue...
http://forum.xda-developers.com/showthread.php?t=497241
Trying to find out if there is such a thing as going from extmicro usb that the evo and flyer have to a usb type A (or any other normal usb).
Need a right angle to plug into tablet for car install and found that I can fit a microb angled cable into the tablet, but now need to take the car charges extusb and get an adapter to hook it all together.
You can just buy a regular micro USB extended cable. It fits in the flyer/view charge port.
Proprietary cable is the one on the right. Regular micro USB on left.
I am installing the tablet in dash of a car.
I have the oem car charger because its only one with right voltage. But I need a angled usb for clearance issues. So im trying to figure a way to go from the charger EXTMICRO usb to the angled usb.
Searched around and have come up completely empty.
I'm working on the same project and found this thread searching (again) for more info on extusb. The solution I came up with for getting enough clearance to use the port requires disassembly and if you plan on keeping the warranty, it's probably not a good option for you.
Anyway, my solution was to make some small right-angle brackets for the pcb that contains the extusb port. It requires material for the angle brackets and two small screws with nuts. See attached for a better idea.
I actually got the tablet installed and fairly well, but have since removed it to come up with better designs for charging, access to the power button (and possibly volume buttons) for recovery actions, turning the screen on/off with ignition, and potentially microphone relocation.
You may want to check out http://www.dealextreme.com/ for right-angle and other adapters if you don't want to open up the tablet.
PS: Protect that screen. The plastic is very soft and will easily scratch.
I don't follow.
I thought the HTC car charger was a plug with a USB port in it just like all the others. I thought this might help, but I probably have no idea what you're really looking for
http://www.amazon.com/Cables-Go-Right-Angled-Micro/dp/B005EV2LAM
If you *need* to use the 12pin micro usb that the view has (which from my understanding was only there for the docking station utility), then you might be out of luck unless you can build something yourself.
Im looking for a cable like you linked to, but then I need a way to connect the flyers car charger special usb tip into it. Only way I can think of is to carefully grind the corners so that it will fit into a micro B female connection.
But the chargers are not cheap and if I F*** it up Im out $30
On a kia soul forum where others are planning on doing the same install with the flyer, one guy has come accross a company that makes custom cables. He said that if We send the car charger to them they will replace the usb tip with a micro B 90 degree angle for $25.
So A person is sending the charger to them to have it done and is going to let us know how it comes out.
jacobbones, can you provide a link to the kia soul flyer thread?
Yes, here it is.
http://www.soulhamsters.com/forum/i...ale-again-24feb-7-android-tablet-199-shipped/
Talk about the custom job is near the end of the posts
opening up the car charger and replacing the cable is incredibly simple. I have done it so many times, I can probably do it blindfolded. I actually had to go and replace the OEM chargers cable with the USB cable that it came with because my damn dog chewed threw the charger cable. Didn't come back very pretty, but it works, that charger has got the be the best charger built I have ever seen, incredibly difficult to open, but I'm sure the car charger is a lot easier to open, you just need a soldering gun and it should be easy.
Sent from my ADR6425LVW using xda premium
First off I'd to say hello from Alaska,
Ok this may sound strange but does anybody out there know where i might find or have one made, I'm looking for a cable with 2 40 pin connectors on both ends, 1 male and the other female. This is for my TF201 and dock, I would use it so I don't have to take off the case to the Prime just plug in to the prime and to the dock..
Thank you all Stan
Cables to Go should be able to do this for you. I've had them make custom cables for me before. It likely won't be cheap, but they should be able to do it.
www.cablestogo.com
Just in case anyone was curious, I thought I would try to get lucky and see if a female-female USB adapter with a standard ASUS 40-pin cable on either end would work. However, it was only a novel attempt and the tablet does not recognize the dock as I had hoped.
I am sure Cables-to-Go could get something to work, but I agree that it will be quite expensive. It would be nice if there was a jumper cable accessory to accomplish this same concept since I am in the same position as the OP and typically carry the tablet in its own case and only use the dock when I have alot of typing to do.
On a side note, I did confirm that my Logitech Anywhere Mouse with the Unifying Receiver does work 100% with my tablet and Dock!....I just may be able to leave the laptop at the office yet!
Does anyone have a mapping of the pins and wires? I would like to try and "splice" two cables together to try and make a jumper cable but would need to make sure that I make the right connections. Any assistance would be greatly appreciated.
I don't think that's going to work for several reasons.
First and foremost, if use two TP USB cables as the souce of the parts, you'll end up with a "jumper" cable with male connectors at both ends. You need male to female, remember?
Secondarily (and almost as important) is the number of contacts on the USB end of the cable. USB has four conductors plus shield and nine conductors plus shield in USB 3. Taking a cursory glance at USB plug on my TP cable, that's all there is. I don't see any additional conductors.
Following this, it's EXCEEDINGLY unlikely that the cable has 40 wires (one for each pin on the Prime end) running the full length. If it did, where would they connect to on the USB plug? Kinda silly to include extra copper to go nowhere.
Instead, if you were to pry open the 40 pin male plug, you'll see that most the pins aren't connected to anything. They're not needed for the USB cable.
Sorry to say, this just isn't going to work.
If you do choose to clip one of your cables just to have a look-see, cut the cable somewhere in the middle. If you cut right up next to the USB plug, you won't have ample wire there to repair what you're about to break.
I am aware that you will need a female adapter to make a true "jumper" cable. However, there may be a way of jerry-rigging a connection to the dock if a female connector can't be found (I have yet to find a part online).
My question is more in regards to whether or not anyone had a schematic of which of the pins are connected to which of the respective USB pins so that I could determine the best way of making a connection....short of having a cable for the ASUS TF201 like this: iPhone Extension Cable
Hi,
Someone stepped on my USB cable when it was charging and bent/broke the USB end of the cable (not the end connected directly to my prime), the wires are loose and i'm trying to solder the wires to another USB cable that was lying around.
However i have not succeeded in making this work, probably because im connecting the cables wrong.
Can anyone tell me which wires are supposed to connect to what colours of the usb cable? They're 5 wires in a ASUS USB cable, but 4 in a regular USB cable and not all colours are the same...
Thank you!
Well the Asus cable is a USB 3.0 I believe since it uses up to 15 volts, which means you need another USB 3.0 end to connect to. Other than that I am unsure about the matching of the wires.
Anyone know about a splitter that will take the 30-pin input and let you use one side for the 30-pin power adapter and the other side for 30-pin accessory like USB OTG pigtail?
I'm in the same boat,
Search and search but nothing,
You get USB to 2 30-pin but nothing for 30-pin to 2 30-pin adapters
The only option you have is to buy a Galaxy Tab break out board from Kinetica and solder your own cables to it..
What do you want to use at same time?
It would be nice to run external power while having an accessory plugged in such as the SD or USB drive or keyboard. I have 2 USB keyboards that have the pointing device built into it.
look in m y post in the make your own cables thread.
i added power to the odks circuit board and can watch movies via hdd at same time as charging.
easier way would be use the breaK out board though..
I have the connector parts, just I have to know the pin assignments...
http://forum.xda-developers.com/showthread.php?t=1155065&page=11
Look at this thread..
Try my post first one before this page..
It explains it..
pin 7 is the posative 5v @2amps...
pin 30 is the earth..
(this is how i run it in car connected to 2 amps 5v source)
works well and if start close to 100 percent battery power leave it plugged in it doesnt drop anything even after watching 4 movies in a row still is 100 percent.
eventually i disconnected it to let the battery drop down alittle as not sure if good to keep it at full charge?
Maybe the best way would be try to follow my dock mod?
that way you can just use the 30 pin usb adapter and add a powered hub.
havent given an update on "line out" output as my usb adapter is covering it up
the outlet socket.might consider opening it up again and finding out if works then relocate the 3.5 stereo socket outlet.maybe could just solder some wires to it inside and add a new output some where else more accessable..
This is a bit of an old thread, but thought people might like to know that I have found a solution! DealExtreme has a splitter that has 2 OTG connectors and a charging connector....
3-in-1 30 Pin Male to USB Female OTG Hub Cable for Samsung Galaxy Tab - Black + White
http://dx.com/p/3-in-1-30-pin-male-...ble-for-samsung-galaxy-tab-black-white-153246
Here is the link to the cable post .
http://forum.xda-developers.com/showthread.php?t=1155065&highlight=cables
ToastyZ71 said:
This is a bit of an old thread, but thought people might like to know that I have found a solution! DealExtreme has a splitter that has 2 OTG connectors and a charging connector....
3-in-1 30 Pin Male to USB Female OTG Hub Cable for Samsung Galaxy Tab - Black + White
http://dx.com/p/3-in-1-30-pin-male-...ble-for-samsung-galaxy-tab-black-white-153246
Click to expand...
Click to collapse
Havent seen that cable before...anybody tried it?
Just curious IF and HOW it works...
I modded my dock to accept charge and host at same time but only triggers charge when hdd is connected whilst power applied.
I've got one from ebay. But its very poor quality. Its functionality is OK, but you cannot charge the Tab. External power is used to power the USB devices. It switches between internal Tab 5V and external 5V when applied. It ok with USB hdd that needs power.
o.k. thanks..
Cant help but wonder about the possibility of using it as charging and host at same time by using different resistor than 20k.not sure if you guys seen the thread about host and charging on galaxy s3 (hw mod) but they discovered a different resistance value 40.2k that could make the power part of the usb travel in both directions at the same time allowing this to happen...
im thinking the same could maybe happen for our 7.7 tab.
rEVOLVE said:
Anyone know about a splitter that will take the 30-pin input and let you use one side for the 30-pin power adapter and the other side for 30-pin accessory like USB OTG pigtail?
Click to expand...
Click to collapse
Chdck this out. Haven't tried yet, but this ought to work.
http://www.ebay.com/itm/130707719450
Sent from my GT-P6800 using Tapatalk 2
Manipur said:
Chdck this out. Haven't tried yet, but this ought to work.
http://www.ebay.com/itm/130707719450
Sent from my GT-P6800 using Tapatalk 2
Click to expand...
Click to collapse
Ordered. Will report back once i get it.
ToastyZ71 said:
This is a bit of an old thread, but thought people might like to know that I have found a solution! DealExtreme has a splitter that has 2 OTG connectors and a charging connector....
3-in-1 30 Pin Male to USB Female OTG Hub Cable for Samsung Galaxy Tab - Black + White
Click to expand...
Click to collapse
Ordered this one few days ago but unfortunately it's not in stock and they don't know when they will have it back in stock so, are there some other options?
rEVOLVE said:
Ordered. Will report back once i get it.
Click to expand...
Click to collapse
Hey, did you get it? How is it?