Guys yesterday i bought a brand new kindle 7" and today i bricked it
i was tryin to install gapps , after few times of fail i decided to try cpasjuste's flashable zip which is at here :
http://forum.xda-developers.com/showthread.php?t=2577826
i was following steps but at a reckless moment i flashed zip to stock rom port then i realised that im makin mistake but it was too late. i powered off the device then tried to open but it did not. After that - another mistake - i made a factory reset. I need your help and ideas.
I was using safestrap with rooted device, at grey boot screen windows is not seeing device at ADB
Sorry for bad language , thanks for help. Here is my device ;
https://www.youtube.com/watch?v=FpNXGcEW21Q
Just ran into that same problem myself :/
Wondering if there is anything we can do to get back into safestrap or if I need to send mine in.
I have same.problem too..
Anyone know solve this problem plz..I known GSLEON3 is one.of solve this problem
Please help us..
Im living in Turkey and we dont have technical support in here only i can do is lookin to device and laugh
Possible Solution
hello
I am also bricked, and I am in the proccess of finding a solution. Have you tried fastboot, but you also need a fastboot cable (factory cable) and fastboot utility for this to work. if you are in luck, maybe the utility will recognise you device and you can insert the following command "fastboot -w -i 0x1949", Good Luck.
Let's hope it works!
My rooted Kindle Fire HDX 7″, maybe hard bricked after factory reset (wipe all) ?
now, it just show “Kindle Fire” and stop here forever ! yesterday, i still turn on and turn off normally !
But today, after I tried to Factory Cable method, it’s quite ! “waiting for device” show so long ! then, I turn off by hold power, and all will be : no signal when i plug in charger ! no turn on by press power button ! no connect to PC, no ADB, in Devices manager on PC, only show “QHSUSB_BULK” ???
I have read a thread on this sites, by long press power button in about 2-3 minutes, and my KF turned on and show “kindle fire” as before !
and whenever i turn off by hold power, my KF will be quite ! and PC only show “QHSUSB_BULK”, to turn on, I must long press power in 2-3 minutes as… again and again !
if my KF stuck on “kindle fire”, when usb cable is plugged, PC will show “Portable devices – MTP USB Device” in Device manager !?
I tried installing Kindle Fire driver, ADB driver, Android SDK… no effect ! In command prompt, I type “adb devices”, it show “list of devices attached” and nothing !
I’m confused and nothing I can do ?
So, Please help me !
Thanks you !
STARBITZ said:
My rooted Kindle Fire HDX 7″, maybe hard bricked after factory reset (wipe all) ?
now, it just show “Kindle Fire” and stop here forever ! yesterday, i still turn on and turn off normally !
But today, after I tried to Factory Cable method, it’s quite ! “waiting for device” show so long ! then, I turn off by hold power, and all will be : no signal when i plug in charger ! no turn on by press power button ! no connect to PC, no ADB, in Devices manager on PC, only show “QHSUSB_BULK” ???
I have read a thread on this sites, by long press power button in about 2-3 minutes, and my KF turned on and show “kindle fire” as before !
and whenever i turn off by hold power, my KF will be quite ! and PC only show “QHSUSB_BULK”, to turn on, I must long press power in 2-3 minutes as… again and again !
if my KF stuck on “kindle fire”, when usb cable is plugged, PC will show “Portable devices – MTP USB Device” in Device manager !?
I tried installing Kindle Fire driver, ADB driver, Android SDK… no effect ! In command prompt, I type “adb devices”, it show “list of devices attached” and nothing !
I’m confused and nothing I can do ?
So, Please help me !
Thanks you !
Click to expand...
Click to collapse
Responded here; please do not cross/multi post.
Related
Hi My DNA has stuck and screen is "OFF" responding, this happened while i was trying to flash recovery.
Device was working perfectly and i probably did something wrong.
I tried all tricks & tips i am familiar with, no luck , the device does not get into "bootloader" or any other mode.
The device is charged so its not a battery issue.
when i connect it to the PC via the USB i hear 2 beeps instead of 1 beep as i used too.
Also when i tried all kinds of games with the power button + volume down at the same time, this does not help at all.
When i connect the device to the PC and open terminal , i use adb device , i get nothing nothing.
Need a smart advice from someone who can help.
Thanks,
Goren
itzik-g said:
Hi My DNA has stuck and screen is "OFF" responding, this happened while i was trying to flash recovery.
Device was working perfectly and i probably did something wrong.
I tried all tricks & tips i am familiar with, no luck , the device does not get into "bootloader" or any other mode.
The device is charged so its not a battery issue.
when i connect it to the PC via the USB i hear 2 beeps instead of 1 beep as i used too.
Also when i tried all kinds of games with the power button + volume down at the same time, this does not help at all.
When i connect the device to the PC and open terminal , i use adb device , i get nothing nothing.
Need a smart advice from someone who can help.
Thanks,
Goren
Click to expand...
Click to collapse
You can try going here and asking for advice: http://chat.andirc.net:8080/?channels=#droid-dna
If you are using windows what does it call the phone under device manager when you plug it in to the computer?
Hi,
I have on my tf201 latest official firmware, 4.1.1 build-number: JRO03C.WW_epad-10.4.2.18-20121122.
As Asus doesn't provide any more updates for our device and mine is out of warranty I'm finally ready to move on to some custom roms.
My tablet is Rooted.
Now after a lot of reading I thought it would be wise to do a backup of everything and make my device unbrickable.
I started to follow the instructions on this site : matthill.eu/android/transformer-prime-tf201-jellybean-nvflash
At first I backed everything up with Titanium Backup and then I did a factory reinstall, so I would have a clean tablet to start.
Then I installed the unlocking tool and succesfully unlocked my device.
I restarted my tf201 with holding the volume button down to get the options to enter fastboot.
When I got to the selection menu, I press the volume button a few times to select the USB-icon.
Then I press the volume up button to enter fastboot, but nothing happens. It just freeze.
The only thing I can do is hold the power button until my tablet restarts.
Also, since i'm on JB I never could connect it on my pc anymore. It even doesn't show up as an unknown device.
So when I want to use ADB I have to use ADB Konnect (wireless ADB).
JNiels1980 said:
Hi,
I have on my tf201 latest official firmware, 4.1.1 build-number: JRO03C.WW_epad-10.4.2.18-20121122.
As Asus doesn't provide any more updates for our device and mine is out of warranty I'm finally ready to move on to some custom roms.
My tablet is Rooted.
Now after a lot of reading I thought it would be wise to do a backup of everything and make my device unbrickable.
I started to follow the instructions on this site : matthill.eu/android/transformer-prime-tf201-jellybean-nvflash
At first I backed everything up with Titanium Backup and then I did a factory reinstall, so I would have a clean tablet to start.
Then I installed the unlocking tool and succesfully unlocked my device.
I restarted my tf201 with holding the volume button down to get the options to enter fastboot.
When I got to the selection menu, I press the volume button a few times to select the USB-icon.
Then I press the volume up button to enter fastboot, but nothing happens. It just freeze.
The only thing I can do is hold the power button until my tablet restarts.
Also, since i'm on JB I never could connect it on my pc anymore. It even doesn't show up as an unknown device.
So when I want to use ADB I have to use ADB Konnect (wireless ADB).
Click to expand...
Click to collapse
When you press up on the USB icon and it freezes that it normal.. This is fastboot mode.
You now must access it over a PC after installing the naked drivers.. If it is not showing on your PC then either try a different PC or your cable is faulty.
Thanks for the quick reply.
I tried once more to enter fastboot. Same result.
But when I disconnected my usb cable to connect it to an other computer, suddenly I got this message on my tablet:
"Starting Fastboot USB download protocol"
This message didn't show up before.
I plugged the tablet back to my pc, but still no device detection in device manager, even when refreshing (So I can't install naked drivers, as it is not recognized).
My computer is a Windows 8.1 system.
I restarted my tablet again, (after disconnecting it from my pc) and followed the procedure to enter Fastboot again.
I waited for the message "Starting Fastboot ..." and then I connected the cable to my other pc (Windows 7 system)
Same result as on the Windows 8.1 machine, not recognized
You say it could be that my cable is broken. Maybe, but it's a strange coincidence that this happened when switching from ICS to JB.
I know JB for the tf201 is been out a long time, and I updated since I could. So over time, maybe my cable could be broken now. But I'm sure I had this problem (not recognizing) since then, because right after updating I wanted to do some things with ADB and so I found out I had this problem.
Hi there,
yesterday I tried to root my new Tablet Z (16GB, LTE, Model: SGP321, Firmware: 10.4.B.0.569) and it doesn't start since then.
I used an ubuntu live CD for all these tasks because fastboot doesn't work on my win 8.1 and my debian wheezy didn't have the libc-dev needed in its repositories (didn't want to mess with packets that weren't yet integrated into my OS).
What I did:
unlock the bootloader according to http://unlockbootloader.sonymobile.com/instructions
I followed the instructions here: http://forum.xda-developers.com/xperia-z/general/how-to-root-10-4-b-0-569-t2590781
a few annotations to this:
the firmware rar didn't include a "Recover.zip", so I used the boot.img directly inside the firmware rar
although sony and this CM tutorial use the "-i" parameter of fastboot, I didn't use it because it wasn't used by the tutorial
after I did the "fastboot reboot" step, the device wasn't listed anymore when typing "fastboot devices", which, I think, is okay since the device should restart then.
I think it didn't really restart, because the LED on the side glew red.
I tried to turn on the tablet but it didn't do anything (the LED kept glowing red).
I tried holding vol up and power for a few seconds (until the LED blinked first once and then three times) but the tablet wouldn't do anything except for the LED glowing red. at somepoint, the LED would turn off (I think that happened when I hold vol up and power for more than 10 sec).
I was able to let it glow red again by pressing vol up and power again and release the vol up button before the power button.
I also tried to use the PC companion on my windows machine to repair the tablet but the tablet wasn't even recognized (either using the fastboot-procedure by holding vol up while connecting the tablet nor normal plugging in...)
any ideas what I could do next?
Same Problem!
Hey wullxz!
I have the same problem. Red LED most of the time, and I cannot make ANY USB connection to the PC. The tablet won't show up in the device manager. So obviously cant use flashtool, nor PC companion. Ive tried all this volume up and down button stuff, but simply cannot get it to show up on the computer.. Tried a different USB cable as well.. Same issue. The USB port is definitely not broken. Its brand new..
Have you found any solution ? Or anyone else? Mine just got back from Sony Repair.. they wont fix it cuz they detected that Ive tampered with the original software.... meaning Warranty Lost!
Great!
hi,
i also sent mine to sony for a repair. i wrote that i did a firmware update and the tablet wouldn't boot afterwards.
i didn't try the bootloader-unlock again afterwards.
Help Needed!
Tablet Z with unlocked bootloader and rooted 10.1.C.0.370
My issues occured after a downgrade to 4.1.2.
I CAN:
1) Start my tablet, everything normal...
2) Charge my tablet
3) Go into safe mode
4) Go into fastboot mode (solid BLUE LED)
5) Use the memory card and use root apps (maybe this could help restore?)
I CAN NOT:
1) Get my PC to recognize that a USB device is connected. Neither in Mass Storage mode, Media mode, nor fastboot mode.
- Tried with several cables and computers (this is not a driver issue, since it won't show up at all in device manager)
- Flashtool obvious;y says, no device connected
2) Get in to flashmode: device blinks red for about half a second, then green for half a second, and then LED is off. Nothing recognized via USB on PC
3) Get into recovery mode
4) Update over WIFI (fails because unlocled bootloader I suppose)
Any help would be greatly appreciated!
i think you should open a new thread for your problem because it seems like it's not really similar to my issue.
you should get more/better replies in an own thread.
Oki
wullxz said:
i think you should open a new thread for your problem because it seems like it's not really similar to my issue.
you should get more/better replies in an own thread.
Click to expand...
Click to collapse
Oki thnx, will try that!
centinel_x said:
Tablet Z with unlocked bootloader and rooted 10.1.C.0.370
My issues occured after a downgrade to 4.1.2.
I CAN:
1) Start my tablet, everything normal...
2) Charge my tablet
3) Go into safe mode
4) Go into fastboot mode (solid BLUE LED)
5) Use the memory card and use root apps (maybe this could help restore?)
I CAN NOT:
1) Get my PC to recognize that a USB device is connected. Neither in Mass Storage mode, Media mode, nor fastboot mode.
- Tried with several cables and computers (this is not a driver issue, since it won't show up at all in device manager)
- Flashtool obvious;y says, no device connected
2) Get in to flashmode: device blinks red for about half a second, then green for half a second, and then LED is off. Nothing recognized via USB on PC
3) Get into recovery mode
4) Update over WIFI (fails because unlocled bootloader I suppose)
Any help would be greatly appreciated!
Click to expand...
Click to collapse
let it charge to 100%, check for flashmode drivers installed and then try attaching it to pc only when flashtool asks you to do it.
Rootk1t said:
let it charge to 100%, check for flashmode drivers installed and then try attaching it to pc only when flashtool asks you to do it.
Click to expand...
Click to collapse
Hey thanks for your reply... It wont go into flashmode... Theres something fundamentally wrong.. I cant figure out what... I leave it plugged in for 48 hours..but it doesnt really get full.. the most Ill get the orange LED.. like 50%... now its on since about 12 hours.. no LED on at all... strange..
But yea.. no flashmode... Nothing showing up when connecting the USB cable... nothing in device manager..and therefore flashtool sees nothing!
SOLVED
Problem solved! I can't believe it. Two bad(?) USB cables. Bought a new one, charges fine, flashmode fine. Flashed stock ROM.
However the Camera still doesn't work. Maybe the problem of the cable inside which may have come loose!
Hello (i know my english is terrible but i need help)
i have bought not long ago BV6000 and i use format option in SPflash tool (not exept bootloader, i pick format all). After this phone is dead. No respond for charging, not respond when i connect him to computer. When i connect phone to computer and push volume + button computer start see phone for 1 second, then again he disappear for +-5 second and next time he start seen and again, again....
Is any method to bring back to life this phone or only producer can help me?
When i format phone i lost IMEI numbers or IMEI should be still saved in phone?
Emik3 said:
Hello (i know my english is terrible but i need help)
i have bought not long ago BV6000 and i use format option in SPflash tool (not exept bootloader, i pick format all). After this phone is dead. No respond for charging, not respond when i connect him to computer. When i connect phone to computer and push volume + button computer start see phone for 1 second, then again he disappear for +-5 second and next time he start seen and again, again....
Is any method to bring back to life this phone or only producer can help me?
When i format phone i lost IMEI numbers or IMEI should be still saved in phone?
Click to expand...
Click to collapse
When you do the volume up thing, in fastboot, do you see your device?
RAZERZDAHACKER said:
When you do the volume up thing, in fastboot, do you see your device?
Click to expand...
Click to collapse
Yes computer see my device but only for 1 second. When i hold volume up all time computer see my device for +-1 second and then my device disappear for +-5 second and then again from begining 1 second see......
When i push volume + for short time, computer see device for 1 second and then device disappear.
And when i try flash my phone by using SPflash tool, proces start and get error at start cause device disappear.
This phone have Android Marshallow.
Oh i read some topics. When i try run device in fastboot mode the device dont turn on, nothing happend.
Emik3 said:
Yes computer see my device but only for 1 second. When i hold volume up all time computer see my device for +-1 second and then my device disappear for +-5 second and then again from begining 1 second see......
When i push volume + for short time, computer see device for 1 second and then device disappear.
And when i try flash my phone by using SPflash tool, proces start and get error at start cause device disappear.
This phone have Android Marshallow.
Oh i read some topics. When i try run device in fastboot mode the device dont turn on, nothing happend.
Click to expand...
Click to collapse
Alright, with this one second, have the "fastboot reboot-bootlaoder" command ready and then, when it sees it, immediately hit enter. Report results.
RAZERZDAHACKER said:
Alright, with this one second, have the "fastboot reboot-bootlaoder" command ready and then, when it sees it, immediately hit enter. Report results.
Click to expand...
Click to collapse
Dam, i cant add picture.
When i try use this command after installing adb i see in cmd waiting on any device and when i connect phone nothig happend, still waiting.
I will try on another computer. I have computer with windows 10, in cmd i have waiting for device after write "fasttboot reboot-bootloader" command but phone is seen like communication port (com 1). Anyway i have instaled drivers for this phone (for normally working, and they are not drivers for this phone on windows 10)
Before i have pick in SPflash tool:
Format--->auto format flash---->format whole flash
so i think bootloader is formated and he need recover or reinstal
On computer with windows 7 is this same but in device menager he see phone named "MTK USB Port" in cmd after use reboot bootloader command cmd all time waiting for device.
I have installed MediaTek PreLoader USB VCOM Port but device dont use this drivers, when i connect the device use MTK USB Port or is added like new port.
Yup, but i dont want firmware update but i need firmware repair cause i get phone with bugged firmware and factory default settings not help.
Blackview BV6000 Flashing Android 7.0
Follow the link below if you wish to #FLASH your #BLACKVIEW #BV6000 with the latest official #Android 7.0 #NOUGAT firmware..
https://dreamworks75.blogspot.in/2017/08/rom-flashing-guide-blackview-bv6000.html
A while back I tried flashing a rom using TWRP and after it restarted it had a bootloop. I have tried everything I can think of to get this back into recovery mode to flash a good rom. I have tried two computers, both running Windows 10 x64, and neither recognize the Kindle. When I do either an adb or fastboot command it just says "waiting for device". The kindle does not even show up under 'device manager'. It hasn't been recognized for a long time even before I screwed up the Kindle. I have tried several utilities, but none will work due to my device not being recognized. Any help to get this thing back online would be greatly appreciated!!
EDIT: Also, I am able to get into fastboot mode with a fastboot cable I just received in the mail. Doesn't help the pc recognize it thought.
Anyone?
Bump
Connect your kindle to the pc, and let it start bootlooping.
Then, hold the power button for at least 40 seconds. the kindle will turn off early on; disregard this.
now, leaving it attached to PC, turn on the kindle again.
It should now be recognised by PC
After this you can use normal methods to restore it back such as SRT
Sorry for replying 5 years too late, but better later than never I guess :/