Hey guys,
I've got the xperia z tablet (16gb wifi only)
and I had unlocked it, the other day I saw it finally got an OTA update, so I let it update.
apparently that was a bad idea?, I was stuck with the broken android symbol every time i attempted to start the tablet..
I tried the sony software, the recovery thing it has. That has only made things worse, now the tablet refuses to start whatsoever.
Can anyone point me in the right direction? I'd appreciate it very much.
dempster said:
Hey guys,
I've got the xperia z tablet (16gb wifi only)
and I had unlocked it, the other day I saw it finally got an OTA update, so I let it update.
apparently that was a bad idea?, I was stuck with the broken android symbol every time i attempted to start the tablet..
I tried the sony software, the recovery thing it has. That has only made things worse, now the tablet refuses to start whatsoever.
Can anyone point me in the right direction? I'd appreciate it very much.
Click to expand...
Click to collapse
Tried to flash with fastboot an boot.img from CM or an other AOSP ROM, and then enter recovery...
zeus2602 said:
Tried to flash with fastboot an boot.img from CM or an other AOSP ROM, and then enter recovery...
Click to expand...
Click to collapse
My tablet won't give me so much as an led indicator of it charging.
dempster said:
My tablet won't give me so much as an led indicator of it charging.
Click to expand...
Click to collapse
If your not able to flash with fastboot (connect tablet over usb (push the boot button) an load an image file on the Tablet.
HARD-BRICK!!!
dempster said:
My tablet won't give me so much as an led indicator of it charging.
Click to expand...
Click to collapse
Yould could try and have a look at the following thread:
http://forum.xda-developers.com/showthread.php?t=1849170
Hi
I had the same issues when I flashed the wrong ROM. Nothing worked no power light or anything.
Now I can't remember exactly what I did but I started to press buttons and I'm sure that holing the power button and the vol up for a while made it start again and it displayed an error and then went into flash mode .
As I said I'm not sure which buttons I pressed but I know that I held them in for a while
Try using Flashtool... Im pretty sure you can rcover it by flashing a FTF file.
Z Ultra Z1 hardbrick
http://forum.xda-developers.com/showthread.php?t=2646405 :good:
So there is hope. :highfive:
I think I found the testpin. My sgp311 has started to blink after being dead since November, when I bricked it.
I don't have the device pack though.. Do you have any clue on how to find it? I think I just need the sgp311 SEMC package to resuscitate it now... Hopefully...
Sent from my Galaxy Nexus using Tapatalk 4
get the stock ftf file and flash it using flashtools, I was in a bootloop and it worked
i know its an old post but i have to try
i m in a boot loop and i want to find the Fed file in order to do a fastboot....
Can someone give them??
I test my tablet SGP321 with many ROMs.. I end up going to boot loop... Crashes and stuff but I always recover from it.
The things I do before doing anything insane with my tablet
1. Take backup off apps/data
2. Always enable debugging and Unknown Sources
3. Keep the backup of the ROMs
4. Always have the xperia flashtool on my computer
Here's what you can do..
Press and hold the Power button and the Volume Up button for ten seconds until you see a white light flashing three times. While doing this somewhere around in 5 seconds you'll see white led flashing once, but keep on pressing those buttons till it flashes next three times.
After that your tablet will be turned Off.
You can put your device in flash mode and flash a new ROM from Xperia flash tool.
If you get the error "Unknown sources and USB debugging must me enable for flash mode, then your option can be to flash the ROM from fastboot.
Download a ROM (CyanogenMod or any with custom recovery).
Flash the boot.img via fastboot and reboot your device.
Once done you should see a led lit up while the device is booting (pink/magenta color in case of CyanogenMod).
Press the volume up/down button and you should be able to go to recovery mode.
From here you can recover your device easily
And before you do anything make sure you've charged your device well.
Good luck
Related
Hey Guys!
So I have an Xperia P, and ever since I upgraded to JB, I have been having several problems. The system lags a LOT. I cannot see any pictures in my Album, though the pictures are there, when I try calling someone it lags so much that the process ends. And it lags a lot when I try picking up such that I can't hear what they're saying for upto 5 seconds. Either that, or it just ends
So I've been attempting to flash a custom OS, but I've been facing some problems. I have rooted my Xperia. When I went on the xda forum to get the flashboot drivers, the link is dead. I installed them from another source.
When I turn off my phone and I hold the power up button, the blue LED light comes on and I go to device manager to install the custom drivers from the SDK bundle. By that time, my phone's blue LED light wouldve gone and the drivers aren't installed. At least I don't think it has. Soo I really need your help on installing the fastboot drivers and unlocking bootloader so I can flash a custom OS. Please help.
Thanks in advance
GokuSS1
GokuSS1 said:
Hey Guys!
So I have an Xperia P, and ever since I upgraded to JB, I have been having several problems. The system lags a LOT. I cannot see any pictures in my Album, though the pictures are there, when I try calling someone it lags so much that the process ends. And it lags a lot when I try picking up such that I can't hear what they're saying for upto 5 seconds. Either that, or it just ends
So I've been attempting to flash a custom OS, but I've been facing some problems. I have rooted my Xperia. When I went on the xda forum to get the flashboot drivers, the link is dead. I installed them from another source.
When I turn off my phone and I hold the power up button, the blue LED light comes on and I go to device manager to install the custom drivers from the SDK bundle. By that time, my phone's blue LED light wouldve gone and the drivers aren't installed. At least I don't think it has. Soo I really need your help on installing the fastboot drivers and unlocking bootloader so I can flash a custom OS. Please help.
Thanks in advance
GokuSS1
Click to expand...
Click to collapse
Which Windows version are you using? If you are using Windows 7 then try this:-
Download this ZIP File.
Extract the contents on Desktop
Now Open Device Manager by RIGHT CLICKING ON MY COMPUTER>MANAGE>DEVICE MANAGER
Now connect your phone in fastboot mode to the PC by holding the Vol + button while plugging in the cable.
You will see a new device in the device manager with an error sign on it. Instantly double click on that because it will disappear as the blue LED disappears.
A dialog box will open. Disconnect the phone and dont connect it.
Go to drivers tab
Click on update driver.
Now select BROWSE MY COMPUTER FOR DRIVER SOFTWARE
Now select LET ME PICK FROM A LIST OF DEVICE DRIVERS ON MY COMPUTER
Now select HAVE DISK
Now click on browse.
Open the extracted folder and select the android_winusb.inf
Click OK
Select the ADB driver from the updated list.
Now connect the phone again in fastboot mode again.
And then click on NEXT. You have to do this very quickly because as soon as the BLUE LED disappears the driver will not load but it will show that it is loaded.
Try This, If fails, tell me, will tell you other method.
pass oturse
Never Mind, I got it to work
But thanks anyways!!
I have another problem now. Since I unlocked bootloader, when I turn my phone off, it automatically turns back on, but after the sony kogo appears, nothing more happens, the screen is still in use, a faint light comes off of it, but it's blank and black. I had to wait for it to run out of charge so i could turn it back on. Any help?
What version of JB you got?
Even that'sresolved now... Guess that the custom OS was just starting up
I have one more though... Hopefully the last one! I tried flashing a stock ROM - ICS for Xperia P (LT22i) with flashboot. It prepared the filesand the pop-up came asking me to turn it off, press and hold the flashboot button and connect it to the USB. The blue LED light came but it never flashed. In the log it also came that a flashboot device has been connected. Help please!
Thanks in advance,
Goku
GokuSS1 said:
Even that'sresolved now... Guess that the custom OS was just starting up
I have one more though... Hopefully the last one! I tried flashing a stock ROM - ICS for Xperia P (LT22i) with flashboot. It prepared the filesand the pop-up came asking me to turn it off, press and hold the flashboot button and connect it to the USB. The blue LED light came but it never flashed. In the log it also came that a flashboot device has been connected. Help please!
Thanks in advance,
Goku
Click to expand...
Click to collapse
U pressed fastboot button so blue LED came and it wont flash.........
try entering flash mode by pressing vol down while pluggi in usb u shud get green light den flashing starts...........
Install flashboot drivers before flashing
:good::good:
GokuSS1 said:
Even that'sresolved now... Guess that the custom OS was just starting up
I have one more though... Hopefully the last one! I tried flashing a stock ROM - ICS for Xperia P (LT22i) with flashboot. It prepared the filesand the pop-up came asking me to turn it off, press and hold the flashboot button and connect it to the USB. The blue LED light came but it never flashed. In the log it also came that a flashboot device has been connected. Help please!
Thanks in advance,
Goku
Click to expand...
Click to collapse
Flashing ROM in flash mode not fastboot.
how do i do that?
EDIT: I know, lame question... But I'm new to this stuff
GokuSS1 said:
how do i do that?
Click to expand...
Click to collapse
Hold volume down while connecting to ISB., phone turned off of course.
kalyan_kadari said:
U pressed fastboot button so blue LED came and it wont flash.........
try entering flash mode by pressing vol down while pluggi in usb u shud get green light den flashing starts...........
Install flashboot drivers before flashing
:good::good:
Click to expand...
Click to collapse
Thanks!!!!
sorry I hadn't seen it!
where do i get flashmode drivers from?
GokuSS1 said:
where do i get flashmode drivers from?
Click to expand...
Click to collapse
Install fastboot and flash mode drivers with the installer in flashtool directiry (drivers).
Hello,
I was in the process to install a new rom in my tablet,
I first root, the tablet, everything was fine
I unlock the bootloder, and again everything was ok
So I extract the boot.img from a Cyanogen rom as describe in one tutorial and put it in the tablet with a fastboot instruction.
After that my tablet seems to be dead.
The only life trace is when I push power and + during a certain time, a violet ligkt blinked one, then a blue blinked one, and after a blue blinked twice.
Nothing more
Mot possible anymore to go in fastboot mode.
Any kind of help is welcome, thanks in advance
gpga said:
Hello,
I was in the process to install a new rom in my tablet,
I first root, the tablet, everything was fine
I unlock the bootloder, and again everything was ok
So I extract the boot.img from a Cyanogen rom as describe in one tutorial and put it in the tablet with a fastboot instruction.
After that my tablet seems to be dead.
The only life trace is when I push power and + during a certain time, a violet ligkt blinked one, then a blue blinked one, and after a blue blinked twice.
Nothing more
Mot possible anymore to go in fastboot mode.
Any kind of help is welcome, thanks in advance
Click to expand...
Click to collapse
just put it into flash mode and flash the stock sony ftf file on it :fingers-crossed:
power off your tablet (in your case it is already done)
hold the volume down button while connecting it to the computer
download and install the sony ericcson flash tool
download the ftf file for your tab z
flash it
done
hassanman1997 said:
just put it into flash mode and flash the stock sony ftf file on it :fingers-crossed:
power off your tablet (in your case it is already done)
hold the volume down button while connecting it to the computer
download and install the sony ericcson flash tool
download the ftf file for your tab z
flash it
done
Click to expand...
Click to collapse
Thank you so much for the information, it's work. I recover my tablet, not exactly the same but it is completely usable
no problem at all ....
gpga said:
Thank you so much for the information, it's work. I recover my tablet, not exactly the same but it is completely usable
Click to expand...
Click to collapse
Im really happy to know that i could help
always remember, it is really hard to fully brick a sony device
my xperia device is stuck on the sony logo. wont pass that part. doesn't go into flashmode or fastboot, nothing. what can I do plz I need help. cant use flashmode on the pc as the computer never recognizes the phone bcuz it doesn't go into fastboot mode.
If your phone even starts, then fastboot and flashmode should work just fine. What's the last thing you did before it wouldn't boot?
1. Hold VOL UP while plugging it in the USB on your computer. The LED should get blue
2. Either use fastboot through command-line or use QuickIMG to boot a custom kernel with recovery.
3. Flash or restore a ROM
Klaos3000 said:
If your phone even starts, then fastboot and flashmode should work just fine. What's the last thing you did before it wouldn't boot?
1. Hold VOL UP while plugging it in the USB on your computer. The LED should get blue
2. Either use fastboot through command-line or use QuickIMG to boot a custom kernel with recovery.
3. Flash or restore a ROM
Click to expand...
Click to collapse
I was trying to unroot the phone to go back to stock and update to stock lollipop. the led lights don't light up anymore, holding volume up or down doesn't do anything as soon as I plug in the usb cable the screen comes on and it stays on the sony logo.
antrax360 said:
my xperia device is stuck on the sony logo. wont pass that part. doesn't go into flashmode or fastboot, nothing. what can I do plz I need help. cant use flashmode on the pc as the computer never recognizes the phone bcuz it doesn't go into fastboot mode.
Click to expand...
Click to collapse
Do the following exactly as outlined.
1- with the phone DISCONNECTED from your pc or charger, hold the power and up buttons until it vibrates and turns off.
2- open the flashtool and select an ftf to flash, and wait for the message that asks you to connect the phone in flash mode.
3- the phone must still be off. Hold the down button and connect the phone to the usb port in the pc. The flashing will start.
I tried that it goes back to the sony logo.
najoor said:
Do the following exactly as outlined.
1- with the phone DISCONNECTED from your pc or charger, hold the power and up buttons until it vibrates and turns off.
2- open the flashtool and select an ftf to flash, and wait for the message that asks you to connect the phone in flash mode.
3- the phone must still be off. Hold the down button and connect the phone to the usb port in the pc. The flashing will start.
Click to expand...
Click to collapse
I tried that. Doesnt work
antrax360 said:
I was trying to unroot the phone to go back to stock and update to stock lollipop. the led lights don't light up anymore, holding volume up or down doesn't do anything as soon as I plug in the usb cable the screen comes on and it stays on the sony logo.
Click to expand...
Click to collapse
How did you try to unroot? It's weird if you don't have working fastboot or flashmode, and without those, you're pretty much screwed. Those two should work even if you screw up big-time, like flashing a wrong kernel, but you must have done something weird if they stopped working?
And let me get this straight, you are pressing and HOLDING the volume buttons when you plug it to your computer, right? Make sure that the device is completely off by pressing and holding POWER + VOL UP. It'll vibrate a couple of times. Note that you're not supposed to be connected to the computer, since it'll then just boot again.
Then press and HOLD VOL UP for fastboot (blue LED), OR VOL DOWN for flashmode (green LED flashing shortly)
You probably already know these steps, but we have to make it absolutely certain that it's a hardware issue, and not an issue with the thing you do
Klaos3000 said:
How did you try to unroot? It's weird if you don't have working fastboot or flashmode, and without those, you're pretty much screwed. Those two should work even if you screw up big-time, like flashing a wrong kernel, but you must have done something weird if they stopped working?
And let me get this straight, you are pressing and HOLDING the volume buttons when you plug it to your computer, right? Make sure that the device is completely off by pressing and holding POWER + VOL UP. It'll vibrate a couple of times. Note that you're not supposed to be connected to the computer, since it'll then just boot again.
Then press and HOLD VOL UP for fastboot (blue LED), OR VOL DOWN for flashmode (green LED flashing shortly)
You probably already know these steps, but we have to make it absolutely certain that it's a hardware issue, and not an issue with the thing you do
Click to expand...
Click to collapse
I was going to flash the stock rom using flashtool right but everytime i tried to put the phone into fastboot mode it would go to the battery icon. At this point the phone was working fine. But no fastboot mode at all. Then i factory erased the phone through twrp. After that it doesnt boot up. Just sony logo no led lights. Even if i do vol up or down. Straight to the sony logo. Vol up plus power button, vibrates couple of times. I redo the process and it goes back to the sony logo.
antrax360 said:
I was going to flash the stock rom using flashtool right but everytime i tried to put the phone into fastboot mode it would go to the battery icon. At this point the phone was working fine. But no fastboot mode at all. Then i factory erased the phone through twrp. After that it doesnt boot up. Just sony logo no led lights. Even if i do vol up or down. Straight to the sony logo. Vol up plus power button, vibrates couple of times. I redo the process and it goes back to the sony logo.
Click to expand...
Click to collapse
The thing is that the screen shouldn't power on when you enter fastboot. The only thing that should go on is the blue LED. I don't use TWRP, and I don't know how it wipes stuff and if it only deletes user data, or if it formats the system. If it does the latter, then it literally wipes the system partition, making it empty, so if you ever format the system, you should flash a new ROM ASAP. A little late for that now though, but I'm still not convinced that fastboot isn't working.
ONE LAST TIME :laugh:
NOTE: The device should be disconnected from the computer.
1. Turn the device OFF by holding and pressing the POWER button and VOL UP. It should be disconnected from the computer by now. Got it? Nice.
2. Plug the USB-cable in the device first, since it's easier to plug it into the computer. Do not plug it into the computer yet. Only the Ultra.
3. Now HOLD VOL UP. Just hold it in.
4. Stick the USB cable, which is already inside your Ultra, to your computer WHILE still holding VOL UP.
5. The blue LED above the screen should light up now. The display should not power on or anything else. The blue LED is the only thing that should turn on.
Still nothing?
Klaos3000 said:
The thing is that the screen shouldn't power on when you enter fastboot. The only thing that should go on is the blue LED. I don't use TWRP, and I don't know how it wipes stuff and if it only deletes user data, or if it formats the system. If it does the latter, then it literally wipes the system partition, making it empty, so if you ever format the system, you should flash a new ROM ASAP. A little late for that now though, but I'm still not convinced that fastboot isn't working.
ONE LAST TIME :laugh:
NOTE: The device should be disconnected from the computer.
1. Turn the device OFF by holding and pressing the POWER button and VOL UP. It should be disconnected from the computer by now. Got it? Nice.
2. Plug the USB-cable in the device first, since it's easier to plug it into the computer. Do not plug it into the computer yet. Only the Ultra.
3. Now HOLD VOL UP. Just hold it in.
4. Stick the USB cable, which is already inside your Ultra, to your computer WHILE still holding VOL UP.
5. The blue LED above the screen should light up now. The display should not power on or anything else. The blue LED is the only thing that should turn on.
Still nothing?
Click to expand...
Click to collapse
I have windows 8. I remember i had a hard time trying to get it into fastboot first time i rooted and unlocked bootloader. Just dont remember what i did to get it working.
antrax360 said:
I have windows 8. I remember i had a hard time trying to get it into fastboot first time i rooted and unlocked bootloader. Just dont remember what i did to get it working.
Click to expand...
Click to collapse
Check whether the drivers have been properly installed in ur PC. If u can't get into flashmode try another system to flash the ftf. Procedure hold volume down while connecting the usb to plug. U will see a green led blink.
antrax360 said:
I have windows 8. I remember i had a hard time trying to get it into fastboot first time i rooted and unlocked bootloader. Just dont remember what i did to get it working.
Click to expand...
Click to collapse
Oh! You probably haven't installed fastboot on your computer. Download and install, and try again.
Klaos3000 said:
Oh! You probably haven't installed fastboot on your computer. Download and install, and try again.
Click to expand...
Click to collapse
Wooooohoooo phones alive jajaja. Thankssss. Though i got some more questions. First time i unlocked boatloader i was told to backup my TA files. what do i do with those now? I just flashed a stock c6806 unbranded rom. When i try to update the phone through settings it says it couldn't verify the update. i retried the process through sony companion app, and it says my phone is modded so it wont do anything.
antrax360 said:
Wooooohoooo phones alive jajaja. Thankssss. Though i got some more questions. First time i unlocked boatloader i was told to backup my TA files. what do i do with those now? I just flashed a stock c6806 unbranded rom. When i try to update the phone through settings it says it couldn't verify the update. i retried the process through sony companion app, and it says my phone is modded so it wont do anything.
Click to expand...
Click to collapse
The TA partition is where your DRM keys are. It's a good idea to backup those keys in case you want to revert to complete stock in the future, or when you need to send it in for repairs. Unlocking the bootloader will remove the keys, but since your device was - weirdly enough, already bootloader unlocked, I don't think you even had DRM keys to start with, which is again, very weird.
No biggie though. Gone is gone. The reason why PC Companion told you that it's been modified, is because you're rooted, and it knows it, so you'll have to unroot before you update. That's only if you're updating through official channels, but you have a second alternative; Flashtool. It allows you to flash stock Sony ROMs, or FTF-files.
But you're saying that you flashed a stock 6806 ROM now, and that's what? 5.0.2? Why don't you just download the .368-update (Android 5.1.1)? Then you'll be on the latest version.
Klaos3000 said:
The TA partition is where your DRM keys are. It's a good idea to backup those keys in case you want to revert to complete stock in the future, or when you need to send it in for repairs. Unlocking the bootloader will remove the keys, but since your device was - weirdly enough, already bootloader unlocked, I don't think you even had DRM keys to start with, which is again, very weird.
No biggie though. Gone is gone. The reason why PC Companion told you that it's been modified, is because you're rooted, and it knows it, so you'll have to unroot before you update. That's only if you're updating through official channels, but you have a second alternative; Flashtool. It allows you to flash stock Sony ROMs, or FTF-files.
But you're saying that you flashed a stock 6806 ROM now, and that's what? 5.0.2? Why don't you just download the .368-update (Android 5.1.1)? Then you'll be on the latest version.
Click to expand...
Click to collapse
I did unlock bootloader myself, TA file were backup. My phone is the 6806 model. The only ftf file i found on xda with a working link was for 4.2 jellybean. I just restored my TA files am going to reflash that stock rom and see what it says now.
antrax360 said:
I did unlock bootloader myself, TA file were backup. My phone is the 6806 model. The only ftf file i found on xda with a working link was for 4.2 jellybean. I just restored my TA files am going to reflash that stock rom and see what it says now.
Click to expand...
Click to collapse
Well carry on then! :laugh:
Klaos3000 said:
Well carry on then! :laugh:
Click to expand...
Click to collapse
Ill keep you posted thanks for replying though i really appreciate that.
Klaos3000 said:
Well carry on then! :laugh:
Click to expand...
Click to collapse
Phones fixed. I needed to restore my TA files in order to be fully stock. Thanks guys.
antrax360 said:
Phones fixed. I needed to restore my TA files in order to be fully stock. Thanks guys.
Click to expand...
Click to collapse
Nice!
Klaos3000 said:
Nice!
Click to expand...
Click to collapse
have my xperia z ultra same error that file will solve i dont know if my sony has unlock bootloader,
Hello guys.
Hoping on your truly support. Have the problem, which cannot solve by myself.
Was trying to flash boot.img from CWM recovery 6.0.3.0 via fastboot. It flashes succesfully, but after rebooting the tablet it doesnt show any signs of life. Was trying EMMA for solving , Flashtool to change kernel, but when plug it through usb, it haven't launched and PC don't recognize any device connected. When i press Vol+ Vol- Power at the same time LED lights with white 3 times and that all.
Was using rooted Lollipop 5.1.1 with unlocked bootloader.
Is there any possibility to reanimate it or its finished totally.
Regards.
Edit.
Many thnx 2 Alok Bajaj for his solution:
Here's what you can do..
Press and hold the Power button and the Volume Up button for ten seconds until you see a white light flashing three times. While doing this somewhere around in 5 seconds you'll see white led flashing once, but keep on pressing those buttons till it flashes next three times.
After that your tablet will be turned Off.
You can put your device in flash mode and flash a new ROM from Xperia flash tool.
If you get the error "Unknown sources and USB debugging must me enable for flash mode, then your option can be to flash the ROM from fastboot.
Download a ROM (CyanogenMod or any with custom recovery).
Flash the boot.img via fastboot and reboot your device.
Once done you should see a led lit up while the device is booting (pink/magenta color in case of CyanogenMod).
Press the volume up/down button and you should be able to go to recovery mode.
From here you can recover your device easily
And before you do anything make sure you've charged your device well.
Good luck
Cheers mate!
hi,
thanks for the tutorial, I try it but*don`t see the second three blue blinks how long usually*takes to wait for them
Hi there! I think I have hardbricked my tablet (SGP321) too. The thing is, mine won't start, no matter what I press and do. If I press the power button it blinks white and if I press the UP button with it, it blinks three times. After that nothing happens. If I connect a USB to it, it just flickers first red and then green. And thats it.
I tried to flash [7.1] CyanogenMod 14 [POLLUX/POLLUX_WINDY][UNOFFICIAL] by CaHbKaUp and chose the Pollux Version from this thread http://forum.xda-developers.com/xperia-tablet-z/general/rom-cyanogenmod-14-t3496758. I also flashed the recommended GApps.
I whiped the sd-card in recovery (twrp) first and then flashed the new rom and GApps.
I think I chose the wrong version, maybe? I flashed my tablet once and I thought I could do it again, the same way as before. Guess I was wrong.
If there is anything I can do to get this back to work, please respond!
with regards
PsyPax
seems like no one is looking at this thread anymore.
edit: Solution found. forgot to unlock bootloader... ^^;
Hardbrick too
PsyPax said:
seems like no one is looking at this thread anymore.
edit: Solution found. forgot to unlock bootloader... ^^;
Click to expand...
Click to collapse
Just ran into the same problem. So there are stil people looking
Didn't know about the bootloader.
Has Android 5.1.1 Stock rom,
rooted it
installed XZDualrecovery from here:
https://forum.xda-developers.com/showthread.php?t=2261606
Then it showed up twrp and I flashed lineage-14.1-20170417-UNOFFICIAL-pollux.zip
ticked "reboot" and ??? nothing
So what are the steps now to get it running again?
baarbaar said:
So what are the steps now to get it running again?
Click to expand...
Click to collapse
Reflash device with Flashtool.
You can't flash custom ROMs with XZDR recovery.
Hello,
I have recently made a horrible mistake, I flashed the incorrect ROM on my Xperia Z3v leaving the phone bricked. I am asking for your help. I have tried using the Flashtool but I am not certain if it's the phone or I that is causing a mistake. The steps thus far that I have followed.
Downloaded: Flashtool & Drivers
Installed: Drivers for Xperia Z3v
Downloaded: Firmware from XperiFirm
Now, the issue next is nothing shows up in my firmware when I attempt to flash. I have checked the source folder the .ftf files are there.
Furthermore:
When I hold VOL UP and plug in the USB>Blue led is indicated
When I hold VOL DOWN and plug in USB>Red flashes with a second of green whilst vibrating
Found this video on youtube: https://www.youtube.com/watch?v=dtaUxuorVSA
Exactly like this, checked for a solution seems like he repaired it via sony. Unfortunately for me I don't have that luxury.
**Update**
I installed the lastest release of flashtool (0.9.22.2) but it occurred to me to revert back to the previous release (0.9.18.6)
Now I can finally see the firmware but I am still having issues actually flashing the file. I get errors such as:
ERROR - root : this bundle is not valid
ERROR - Cannot delete C:\Users\Juan\.flashTool\firmwares\prepared\userdata.sin
**More Information**
I should include I am on a locked bootloader
same
that seem the same with my situation
Okay the green light is flash mode / upgrade mode. The blue light is fast boot. You want it on with the green light on to flash it once it's bricked. You can't flash it using fast boot mode because the boot loader isn't unlocked.
Now what you have to do is get it with the green light on and then the drivers installed.
Can't delete the file means that it had error while trying to flash and all that you have to do is restart the app and that goes away.
Now for the next problem is that I had this one and what I did to fix it is that I had to reinstall the drivers because those weren't correct and I did reinstalled it and it all worked good. Thanks.
Download the correct firmware for your phone (model and Country).
Use flashtool to install it on your phone
Works with a locked bootloader, no need for USB debugging.
The first error might be you ended up downloading the incorrect or incomplete firmware
I had the exact problem that you are having. I ended re downloading the flashtool a few times from various computers and then i got it to work. I figured when i downloaded it the first time i had a version that was to old/new. Or a bad connectiin when i downloaded it first time. After i downloaded flashtool again itthwn worked without issue just as it should. Whatever the provlem was for me was having to do with the download or version i downloaded wouldnt work completely. I think my internet connection when i downloaded it wasnt very good and maybe didnt download it right.
I made the same mistake too, trying to flash a z3 zip file. Then I got to run around my home city to find help. Then there's a guy. He had to open the back cover and connect directly to the circuit board in order to do something about the eMMC and SEtool or... something, I'm not sure. The phone is alive again! (costed quite a lot for a student, but... yay?). Funny though, he said the circuit board is similar to a z2 and not a z3. Maybe you could find someone who knows about these kinds of thing. Hope that help.
Girouette said:
I made the same mistake too, trying to flash a z3 zip file. Then I got to run around my home city to find help. Then there's a guy. He had to open the back cover and connect directly to the circuit board in order to do something about the eMMC and SEtool or... something, I'm not sure. The phone is alive again! (costed quite a lot for a student, but... yay?). Funny though, he said the circuit board is similar to a z2 and not a z3. Maybe you could find someone who knows about these kinds of thing. Hope that help.
Click to expand...
Click to collapse
That's strange were you on a locked bootloader?
Currently attempting to fix it once more, will update if I find anything out.
DireSpook said:
That's strange were you on a locked bootloader?
Currently attempting to fix it once more, will update if I find anything out.
Click to expand...
Click to collapse
Yeah, I think? I mean, it's right out of the box. Also, I think it's worth mentioning that the guy had to use SEtool twice to get mobile signal.
Did you fix the problem? I have the same problem now.
With a Z3v. D6708. I have a problem, got a wrong ROM, the flashee and now not start the phone in any way. The only way to start is "System Recovery" volume + power, which has 4 options: 1. "Continue Power UP", 2. "Safe mode", 3. "Factory Reset" and 4. "Power Down". The thing is try from flashtool but when I give "volume down" and connect the computer does not recognize. When light it even reaches the boot animation. When I give power with USB cable is connected in a loop is vibrating and shows red, blue and green.
I have exactly the same problem of the youtube video.
As it could fix the problem?
Some help ?
Thank you !
Pd. The device only have FastBoot.
did u solve this?
DireSpook said:
Hello,
I have recently made a horrible mistake, I flashed the incorrect ROM on my Xperia Z3v leaving the phone bricked. I am asking for your help. I have tried using the Flashtool but I am not certain if it's the phone or I that is causing a mistake. The steps thus far that I have followed.
Downloaded: Flashtool & Drivers
Installed: Drivers for Xperia Z3v
Downloaded: Firmware from XperiFirm
Now, the issue next is nothing shows up in my firmware when I attempt to flash. I have checked the source folder the .ftf files are there.
Furthermore:
When I hold VOL UP and plug in the USB>Blue led is indicated
When I hold VOL DOWN and plug in USB>Red flashes with a second of green whilst vibrating
Found this video on youtube: https://www.youtube.com/watch?v=dtaUxuorVSA
Exactly like this, checked for a solution seems like he repaired it via sony. Unfortunately for me I don't have that luxury.
**Update**
I installed the lastest release of flashtool (0.9.22.2) but it occurred to me to revert back to the previous release (0.9.18.6)
Now I can finally see the firmware but I am still having issues actually flashing the file. I get errors such as:
ERROR - root : this bundle is not valid
ERROR - Cannot delete C:\Users\Juan\.flashTool\firmwares\prepared\userdata.sin
**More Information**
I should include I am on a locked bootloader
Click to expand...
Click to collapse
got solved? me to have same problem
Bricked for days!
Is anyone still following this thread. I have the same problem after trying to install MIUI 6 on my rooted unlocked TWRP'd Xperia z3V. After the MIUI installation I have nothing but the symptoms below.
Not able to get into flashmode
No screen or bootup
No recovery
Symptoms:
1 -When plugged into PC or wall it only blinks RED/GREEN light and vibrates.
2 -Holding POWER the light turns and stays GREEN until released (then returns to #1)
3 -Holding POWER + VOLUME UP BLUE light stays on and puts phone in Fastboot mode
4 -Holding POWER + VOLUME DOWN does nothing (continues to do #1)
Please Help!!!
Google Sony Developers. Try to unlock your bootloader.
Sent from my D6708 using XDA-Developers mobile app
I think the phone will reject the command. Tried on a bricked z3v and that's the response I get from fastboot with the Sony commands given through the developer aite.
matrix$ said:
Is anyone still following this thread. I have the same problem after trying to install MIUI 6 on my rooted unlocked TWRP'd Xperia z3V. After the MIUI installation I have nothing but the symptoms below.
Not able to get into flashmode
No screen or bootup
No recovery
Symptoms:
1 -When plugged into PC or wall it only blinks RED/GREEN light and vibrates.
2 -Holding POWER the light turns and stays GREEN until released (then returns to #1)
3 -Holding POWER + VOLUME UP BLUE light stays on and puts phone in Fastboot mode
4 -Holding POWER + VOLUME DOWN does nothing (continues to do #1)
Please Help!!!
Click to expand...
Click to collapse
InkBastard said:
Google Sony Developers. Try to unlock your bootloader.
Sent from my D6708 using XDA-Developers mobile app
Click to expand...
Click to collapse
gunz.jones said:
I think the phone will reject the command. Tried on a bricked z3v and that's the response I get from fastboot with the Sony commands given through the developer aite.
Click to expand...
Click to collapse
The phone is not and most likely never will be bootloader unlocked. Planning to buy for another phone is your only option.
I've already moved to a tmo note 4. Not much development there either, but it's nice. Miss the z seires though and may come back to it next year. We'll see how they fair with phones for the next few months state side abs if prices even out on the x or z5.
I fixed mine
I bricked my phone it was just a paper weight Email Me I will make u a video step by step instructions to fix it
[email protected]
carldw said:
I bricked my phone it was just a paper weight Email Me I will make u a video step by step instructions to fix it
[email protected]
Click to expand...
Click to collapse
Unless you're going to post a link or YouTube video we all have access to, wouldn't bother asking people for direct email addresses to send them. That's the reason for PM'S and the forum on general. If you have a fix, we'd all like to know what it is you were able to do that none of us have figured out.
Need to Load Stock ROM
shashikiran said:
got solved? me to have same problem
Click to expand...
Click to collapse
Dear,
You have to load the Stock Rom / Flash it through the tool.
reroot the Phone and try again by clearing Dlavik Cache .
Sorry If am Wrong.
aranda.jc said:
With a Z3v. D6708. I have a problem, got a wrong ROM, the flashee and now not start the phone in any way. The only way to start is "System Recovery" volume + power, which has 4 options: 1. "Continue Power UP", 2. "Safe mode", 3. "Factory Reset" and 4. "Power Down". The thing is try from flashtool but when I give "volume down" and connect the computer does not recognize. When light it even reaches the boot animation. When I give power with USB cable is connected in a loop is vibrating and shows red, blue and green.
I have exactly the same problem of the youtube video.
As it could fix the problem?
Some help ?
Thank you !
Pd. The device only have FastBoot.
Click to expand...
Click to collapse
ok.you power down your phone
---------- Post added at 06:32 AM ---------- Previous post was at 06:21 AM ----------
1-power down your phone.
2-open the flashtool you can chose 32 or 64.almost we chosed flashtool 64.if you can't confirm it.you can oppen your computer and chesk naked (属性) then you will see your computer system is 32 or 64.
3-the new tool version is 0.23 and download it.install it on you computer C .
4Download the D6708 .ftf put it in C. the flashtool will led you. almost I will put it on C/user/.flash/firmwares
5-flash the software will lead you how to use you phone connect you computer with usb .