Sal all,
I cannot find firmware for this tablet. It's a 7inch, dual camera, atm7029 quad core cpu, that doesn't start, but i can write firmware with Actions Pad Product Tool.
The only available firmwares for this type of cpu (atm7029) i was able to find, were from Ainol tablets, but these are not good.(only lights start 1sec)
Can someone help ?
10x in advance !
Hi! There is a similar device firmware from (Russian): (yadi.sk/d/Wku6HWTxKkaKa)
But WiFi and camera other.
System image
Here is the image of the system partition. Dumped with ADB from a working tablet. (512MB)
(mediafire.com/download/roc8870rirvt3hw/actc_system.img)
And this is the image of the recovery partition: (48MB)
(mediafire.com/download/fd30kaio8xb490j/acta_recovery.img)
If you want to see what's inside the images, mount the image in Linux, or use Linux Reader if you're using Windows.
How to use the actc_system.img and acta_recovery.img
Hi, I'm an android newbie needing help. I found this thread while searching for how to deal with a bootlooping Orion TAB-700qc tablet belonging to a friend.
Apparently my friend tried to update the tablet with the wrong update (I'm not really sure what he did), but it went into a bootloop -- it will not get past the "android" screen. I found how to go into the Recovery menu but nothing there would fix the problem. I have downloaded the actc_system.img and acta_recovery.img discussed in this thread, but I need step-by-step instructions for how to use them to get the tablet working again.
Can someone please direct me to instructions that I as a newbie will understand? I have worked a lot with pc's but I have almost no experience with androids.
Thanks,
cmNhu
Related
I now know the Allwinner A13 is a stripped down version of the Allwinner A10, to be clearer the specifications of my Tablet (from UniFlash and AnTuTu Benchmark) are as follows:
Manufacturer: None
Brand: softwinners
CPU hardware: sun5i
CPU model: ARMv7 Processor (VFPv3, NEON)
CPU frequency: 60.0 ~ 1008.0 MHz
Screen resolution: 800 x 444
GPU vendor: Mali-400 MP
GPU version (OpenGL): OpenGL ES 2.0
RAM size: 512 MB DDR2 RAM
Knowing this, I used UniFlash to make a backup of the firmware bt after using UniFlash to try and load a CM9 Rom on to the Tablet, the Tablet died. After alot of googling I discovered AllWinner based chipsets use Live Suite (sometimes called LiveSuit) to flash firmwares on to the device.
To Flash firmware on to the device you need to follow the attached instructions ((http://dragondevs.com/viewtopic.php?f=159&t=390):
Download LiveSuite (http://www.softpedia.com/get/System/System-Miscellaneous/Live-Suit-Pack.shtml)
Install Live Suite
Start Live Suite
Select the Live Suite image file (folder icon
Turn device off (to be sure hold power button for 12 - 20 seconds)
Hold "Volume Up" button down
Connect the device to your PC (while still holding "Volume Up" down)
Start pressing the power button (you may need to do this once a second for 5/6 seconds)
If you haven't installed windows will ask to install a driver for a device (Dive Id will be something like Vf73465789123465435_Id, if the device is in the right mode, A13-MID, ADB-Interface indicates the tablet has connected in anouther mode).
Once this has finished LiveSuite will detect the device and a wizard will flash the firmware for you.
I have found a working firmware which according to AnTuTU Benchmark gives my tablet a rating of 3047 (see firmware section), this is on the higher end of reported A13-MID tablets
I have found out how to install CWM on to the device via SaussageMod (http://www.slatedroid.com/topic/29916-scriptmod-for-allwinner-a1x-platforms/). This solution is untested, further more it may be unnessary futher investigation has shown this website (https://www.miniand.com/forums/forums/2/topics/73) has developed a way of create Live Suite images. This is simplier than installing clockworkmod recovery,
I tried to load the following images on to my tablet and failed completely: http://forum.xda-developers.com/showthread.php?p=31043317 It didn't work and forced me to do a firmware refresh.
My other step for the day was to create Ubuntu 10.10 installation then I began following this guide to construct an Xperia Play CM9 Rom/Kernel. once I have created a working ROM (I own an Xperia Play). I'm hoping to be able to modify the kernel to include the relevent A13 drivers, but one step at a time.
TODO
Create Ubuntu Partition
Follow Xperia Play CM9 Rom/Kernel Guide and create working rom (test on my Xperia Play)
Download CT repository (https://github.com/christiantroy) and compare with Xperia Play CM9 rom
Find the relevent drivers from https://github.com/amery/linux-allwinner leaked source
Retrieve offical MALI 400 MP drivers (parts of it have been released) compare with leaked source
Use UniFlash backup of original Rom along with LiveSuite image creation to try and restore original firmware (see If I understand it properly)
Examine Build.prop find out why original firmware displayed ina phone layout and new one is in tablet mode (potentially reference CM supported Tablets).
Attempt to compile a A13 (Sun5i) based rom
Create a google code page to hold all of these thoughts properly.
Left blank will include rom/firmwares here for future reference
Firmware
https://www.dropbox.com/sh/bzjt7mzuftwz79f/nt7mRMPDj1 - My public Dropbox
http://www.azhuo.net/en/products_A13B_Allwinner-A13_7_inch_Android_4.0_Upgrade.html - password is: tabletpc
http://dragondevs.com/viewtopic.php?f=159&t=390 - McPad F1 firmware
Novo 7 Tools
https://dl.dropbox.com/u/74970692/Novotools_v1.0.apk
SausageMod
http://www.slatedroid.com/topic/29916-scriptmod-for-allwinner-a1x-platforms
Gapps - http://goo.im/gapps/
I have the same tablet and it would be very cool if you succeeded in your attempt to create a CM9 rom for it. I tried ROM made by Tragidy from this thread but there is a problem with touchscreen driver, ROM booted successfully but I could not even unlock the screen cause touchscreen did not work. I finaly flashed rom DCPAD2121.zip using livesuite which I belive is the original ROM that came with tablet and it worked.
I installed clockwordmod using sausagemod successfully, but there is a big problem - no hardware "back" key and only volume up works.
novo7tools.apk works OK for reboot, reboot to recovery or shutdown.
syncing
Thanks, it's slow going at the moment, I only spending ~1 hour each day on it and at the moment trying to sync the CM9 source is painful (it keeps timing out, due to "remote side corruption").
I figure I would start there as all the firmware images I can find are ICS roms (meaning the drivers must be ICS).
Hi, I have the same tablet but I cannot find the firwmare DCPAD2121.zip
Could you upload it please? From dropbox has been deleted
Thanks
You should check this topic:
http://forum.xda-developers.com/showthread.php?t=1861445
WillingMagic said:
You should check this topic:
http://forum.xda-developers.com/showthread.php?t=1861445
Click to expand...
Click to collapse
I tried that ROM, on my tablet after flashing the ROM it got stuck in a boot loop. It might be an idea to steal the config he created. The ROM is pre CM9 release. The A10 Flash kitchen software seems to work. I was hoping on producing a complete Live Suit image that people could flash (figuring our what CT has done on the A10 took a while).
Still having fun trying to sync the repositories, given up on trying to use a Debian VM, I'll will install full Ubuntu on a drive tomorrow, hopefully that will help fix things. It doesn't help most of the guides I can find are out of date and I keep having to make corrections.
I've also uploading all firmware I can find to my dropbox (at 200mb each they will take a while), I won't with tools simply because others ask you not too.
The Dropbox firmware was out of date when I tried to download it sun5i_android_a13-pfdq88_en_D06 firmware worked well for me, the firmwares are located at: https://www.dropbox.com/sh/bzjt7mzuftwz79f/nt7mRMPDj1
Cyanogenmod 9 in not working for you. Did you made data and cache wipe? Can you send me logcat and dmesg output?
You can`t steal my config, you have to remember about credits, and other stuff.
Creating a wiki is useless, there is already wiki for allwinner products, so better update info on it.
Github is better than google code to keep sources.
Using Livesuit=Windows, I hate dual booting just for flashing, Clockwork Recovery or modified SDcard with uboot is better solution.
Current kernel is not working well, with sun5i.
Using VM is stupid, because building rom takes a lot of time on quad core pc without it.
WillingMagic said:
Cyanogenmod 9 in not working for you. Did you made data and cache wipe? Can you send me logcat and dmesg output?
You can`t steal my config, you have to remember about credits, and other stuff.
Creating a wiki is useless, there is already wiki for allwinner products, so better update info on it.
Github is better than google code to keep sources.
Using Livesuit=Windows, I hate dual booting just for flashing, Clockwork Recovery or modified SDcard with uboot is better solution.
Current kernel is not working well, with sun5i.
Using VM is stupid, because building rom takes a lot of time on quad core pc without it.
Click to expand...
Click to collapse
I wiped the caches I couldn't send a logcat or dmesg as the device simply boot looped.
I've been providing links to threads whenever I come across others work, I'm new to android rom development for me this is a research effort which will hopefully produce something cool for my £50 tablet. Basically my day job has switched to developing UI's and I am looking for something new to learn (instead of why is Vaadin, Guice, SWT, Javascript, etc... is putting that button there).
Said dev career has also made me hate Git with a passion (not as bad as perforce but still) since Git integrates poorly with Visual Studio and Eclipse and you end up getting everyone overwriting each others changes. The idea of google code is simply because it makes a good platform for projects and you can use things like git with it. I didn't know about an Allwinner wiki, with all of my Googling I haven't come across it, where is it?
I don't care about build times I'm just researching, alas Debian has caused me enough problems so I've installed ubuntu on to a old disk I had lying around. Considering I've just tried to install Ubuntu via a Net install CD and it has screwed up the GRUB installation (nicely taking out my windows partition as well) can you blame me?
The reason for nabbing the config (and the Xperia Play and Christian Troys) is to understand how they work. Over the years I've found most Open Source software documentation is poor unless you have a set level of knowledge about it already.
Lastly I like automation, I want things to just work. Livesuit does that since I am normally a windows user, I as hoping in the distant future once I understand the build process to set up a Jenkins server to do it and create the whole lot automatically (via the Allwinner flash kitchen). In the even longer term I would like to update FlashTool to do what LiveSuit does. In the near term (next couple of months) I just want to be able to build a CM9 image.
All android and kernel source are keep on git, so changing it is stupid.
This is allwinner wiki: http://rhombus-tech.net/allwinner_a10 you can also update http://elinux.org/Hack_A10_devices
Everyone use CWM and it's standard for unofficial firmware/ROMS
brandonlee2 said:
Hi, I have the same tablet but I cannot find the firwmare DCPAD2121.zip
Could you upload it please? From dropbox has been deleted
Thanks
Click to expand...
Click to collapse
Here's my upload, I packed it in rar format: http://www.mediafire.com/?we4zhgop29bg3dj
I also found it here: https://docs.google.com/open?id=0BzQuMwoMQqvba1VtQ1p1ZWJkR2M
from this forum post: http://www.slatedroid.com/topic/35314-a13-generic-tablet/page__view__findpost__p__421128
I built a CM10 rom for A13 from sources. It boots fine but hangs either at the Android setup wizard or sometimes even at the CM animation.
myfluxi said:
I built a CM10 rom for A13 from sources. It boots fine but hangs either at the Android setup wizard or sometimes even at the CM animation.
Click to expand...
Click to collapse
Mind sharing your repo ?
Trying 4.1.2
Hi all,
So I've tried compiling from 4.1.2 source for my A13 Emgeton Consul 3
It boots up and gets to the CM10 boot animation but it doesn't get past it.
I can adb at first boot until adb stops.
logcat from boot attempt:
http://pastebin.com/gLTrieHm
My build.prop:
http://pastebin.com/Ap9M1tjW
Any pointers as to why it doesn't get past the boot animation?
Hello guys! I know it's not he proper place here to pose my question, but I am definitely at loss!
Do you happen to know if there is a way of rooting this tablet? And if so, does everything work properly after that?
phoivos86 said:
Hello guys! I know it's not he proper place here to pose my question, but I am definitely at loss!
Do you happen to know if there is a way of rooting this tablet? And if so, does everything work properly after that?
Click to expand...
Click to collapse
Mine came pre-rooted.
Just received my MID A13 Tablet. Is this thread dead?
koodiifin said:
Just received my MID A13 Tablet. Is this thread dead?
Click to expand...
Click to collapse
I've gone a bit quiet on the development front, setting up a file/media server & samba domain server to power my home network is eating up my time.
My dropbox contains every image I could find for the tablet, as mentioned previously you can root the device using saussage mod, although my device and every one of those images is already rooted. You can prove this by installing super user.
Sassage mod's clockworkmod recovery doesn't work for me and I was looking at the backup tool in order to generate my own one. If you are aimed at any development, let me know and I will update the main thread
Many have said that they have "lost" "forget" to take backup from original rom. So, i'd like to have backup from my original to go back if/when something goes wrong. How do i do that? What software i need. Do i need to root?
This is from my info sheet:
Model TWD_MID
android version 6.0.1 ?????
Baseband 1.5
Kernel 3.0.8+
Buildnumber: nuclear_evb-eng6.0.1 IMM76D 20120917 test keys
I am in a desperate need for some help:
My tablets specs are these:
Phone model: A13-MID
Brand: softwinners
CPU hardware: sun5i
CPU model: ARMv7 Processor (VFPv3.NEON)
CPU frequency: 60.0 - 1008.0 MHz
Screen Resolution: 800 x 444
GPU vendor: ARM
GPU render: Mali-400 MP
GPU version (OpenGL): OpenGL ES 2.0
Memory size: 353.5 MB
Android version: 4.0.4
Build number: nuclear_pfdq88c-eng 4.0.4 IMM76D 20120821 test-keys
Kernel: Linux version 3.0.8+
I just installed OpenVPN installer and installed the OpenVPN binary in the system/xbin
After that I tried to connect to my university's VPN but when it tried to connect, the tablet lost wifi connection and ever since it doesnt connect to any available wifi network!! I manually deleted the OpenVPN binary, but problem remains!
Do you know where could I find the stock ROM for this tablet in order to re-flash it?
Do you have any other proposals? Anything will help!
Thank you very much!!
I have a Trio Stealth Pro 9.7" Tablet by Mach Speed that came with ICS. It wasn't able to run much of anything so I tried to upgrade and needless to say it didn't work.
First, I installed CWM. I did this because the device appeared to have no recovery mode I could find. That seemed to work at first but then I discovered I could ONLY boot into CWM.
SO, I tried to use Live Suit to flash an img of 4.1.1 (I know, a stock file from the manufacturer would have been best but please don't tell me to download one unless you have a working link - I've tried without success).
When that failed, I figured I'd try something else except now I only get a blank screen - not even an initial logo. The only way I can tell if the thing is on or off is by plugging it into my computer, pressing the power button and listening for a usb connect or disconnect noise. (My computer currently recognizes it as USB Device(VID_1f3a_PID_efe8) although it originally recognized it as a Trio something or other).
Any help would be fantastic. Thanks in advance.
http://forum.xda-developers.com/showthread.php?t=2296921
Please read carefully. You must check first whether you have 9.7 or 9.7C before flashing!!!!
Check this if your tab has the Allwinner a10 chip. This worked great for my A10.
http://forum.xda-developers.com/showthread.php?t=1821398
More Questions
Neptune23 said:
http://forum.xda-developers.com/showthread.php?t=2296921
Please read carefully. You must check first whether you have 9.7 or 9.7C before flashing!!!!
Check this if your tab has the Allwinner a10 chip. This worked great for my A10.
http://forum.xda-developers.com/showthread.php?t=1821398
Click to expand...
Click to collapse
I appreciate the reply but I don't know how to flash a zip without the use of my tablet screen. I can use Live Suit but that only seems to flash .img files.
Also, I'm not sure how to tell if I have the 9.7 or 9.7c
At first guys, excuse me if the topic isnt at right place but i cant find the right section.
So i have a Prestigio Multipad 8.0 HD (PMP5588C).I think i have bricked it.I erased NAND with Amlogic Image Burning Tool and now the device wont boot.The screen is black even when im charging it.I wont boot at all.I tried to boot in recovery but no succsess.Ive tried to boot it normally and in recovery (even when i charged it 10 hours usually it charges for 4 hours) but the screen is black.When i connect it with Power and Vol- buttons it shows up in the device manager as M6-CHIP and ive installed the drivers so now is World Cup Device.Ive tried to use Amlogic Image Burning Tool again but it fails on load spl.Any ideas?
Thanks in advance!
Best regards, Stoio.
Im sorry for my English but im from Bulgaria.
Unbrick amlogic tablets
Hello stoio
I have almost the same Tablet. It's a Prestigio PMP5580C, for me it is labeld as Intenso Tab 814, but they are completely the same. I have tried to find the u-boot.bin in the stock firmware, but I didn't sucess yet. I've downloaded several tools which allows me to make my 16 GB MicroSD card recognized as a 512 MB SD card, there I have to put the files on it to unbrick my tablet, it's amlogic (like my username) (someone told me that this is the chipset). It has a TOSHIBA TC58TEG6DCJTA00 NAND flash chip of 8 GB capazity. I also need help by getting my tablet unbricked.
In the future Inwant to learn with this amlogic based tablet how to create custom ROM's, recoveries and custom boot splash screens.
Thanks for any help, I reall appreciate your help,
Please note that I'm from Germany and my English is not good as it should used to be, but I have a dictionary (as a normal book) where I can get good communication with you. I like the idea of using english only.
Every Image (.img) were made with the dd command, I need to look inside in the images and open the content, I used a hex editor and tried to strip off the 2k of data, but I can't success. I'm using this tutorial:
I'm using this hex editor under linux: Okteta
I don't know how to delete the 2k of data. I need to know what content the partitions have to unbrick my amlogic based tablet, cause I'm seeing still the white android robot, and the charging battery or charged plugin picture, but this tablet doesn't have a bootloader or recovery so I'm out of ideas, the only way for me is to use a microsd card like an live cd to automatically let this tablet flash stock firmware, but where is it? Please help me out, I meight be wrong, it's possible that different repairing ways exist, too.
Hi
I would really appreciate some help,
I have a Cube i6 dual boot tablet however the Android partition is too small for what I need.
So is there a way that I can increase the Android partition and decrease the Windows partition?
Alternatively I thought I would try and flash the tablet with the Android image using the Manufacturing Flash Tool, thereby removing Windows but when I run the MFT my tablet doesn't show up so I'm not able to flash it.
I've gone through the instructions and installed the iSocUSB driver and the Intel Android Driver on my Win 7 PC..
I've installed the MFT and copied the Custom Config file into the MFT installation directory.
In device manager under Android Phone I can see Intel Android Composite ADB Interface and under Intel Soc I can see Intel Soc USB Driver, is that correct?
In MFT I go to settings and change the settings to:
SOC devices VID: 8087， PID： 0A65;
Android devices VID: 8087，PID: 09EF
I choose the XML file to install but then nothing happens because my tablet doesn't show up in MFT.
I would appreciate any suggestions.
Thanks
Increasing the Android Partition Size on Cube i6 Dual Boot
I want to second this request. I have not been impressed with Windows, so I need to increase the partition size for Android or eliminate Windows entirely.
Any suggestion?
Update: I used a different PC and was able to see the tablet in MFT and the flash began. It got part way through the process and the tablet restarted but now it's just stuck on a black screen with an EFI Shell prompt, so no closer to installing the Android image.
Wow, i believe Cube Tablet should give the full instruction of the partition for both Android and Windows OS for its customers.
Besides, i'm also concerned whether there will be any update for the Cube i6 Air Dual Boot tablet? I can't find it any where. I'm eagerly in need to update the latest firmware for my Cube i6 tablet.
Hello,
I was able to flash cube many times.
There is actually an update here :
http://www.51cube.com/ch/DownShow.asp?ID=364 - i used google translate to flash it successfully
however it is still android 4.4.4.
Regarding partitioninig, sure you can. You need to update partition.tbl file.
I did it. I tried to flash rom from telcast where they do have android 5. successfully.
But comparing partition tables I found out they are different, MFT did it without yelling.
Also I exchanged several files and used flash file from cube rom mentioned above, to be more specific I exchanged following files (taken from telcast 5 rom http://forum.xda-developers.com/showpost.php?p=61079769&postcount=8387)
boot.img
partition.tbl
recovery.img
system.img
However touch screen is not working, but at least I have got a boot. Thats where I end, I can not fix touchscreen drivers here, I am too dumb for that
I would appreciate if somebody would create a new rom for cube . If somebody is skilled enough, I can provide more detailed information and files I used.
Asking any further help from me is pointless, as I am not an expert and not so deep acknowledged.
Hi, I am in the same situation; received my Cube i6 yesterday. Did you finally succeed in either flashing an Android-only ROM, or changing partion size? How did you manage? Thanks!
Dear all,
same issue for me... keep me updated I will keep on searching
necesito ayuda tengo una cube i6 con manufacturing flashtools llega al 11% y no avance y no detecta el sig adb, presiono el boton power y volumen - y la ctento a la pc y se reinica la tablet y no ´puedo entrar al bios con esc
thermoska said:
Hello,
I was able to flash cube many times.
There is actually an update here :
http://www.51cube.com/ch/DownShow.asp?ID=364 - i used google translate to flash it successfully
however it is still android 4.4.4.
Regarding partitioninig, sure you can. You need to update partition.tbl file.
I did it. I tried to flash rom from telcast where they do have android 5. successfully.
But comparing partition tables I found out they are different, MFT did it without yelling.
Also I exchanged several files and used flash file from cube rom mentioned above, to be more specific I exchanged following files (taken from telcast 5 rom http://forum.xda-developers.com/showpost.php?p=61079769&postcount=8387)
boot.img
partition.tbl
recovery.img
system.img
However touch screen is not working, but at least I have got a boot. Thats where I end, I can not fix touchscreen drivers here, I am too dumb for that
I would appreciate if somebody would create a new rom for cube . If somebody is skilled enough, I can provide more detailed information and files I used.
Asking any further help from me is pointless, as I am not an expert and not so deep acknowledged.
Click to expand...
Click to collapse
Hi， the 5.0 ROM links don't exist, can you do me a favor to post the ROM? Thanks very much!
Sent from my Nexus 5 using Tapatalk
Hi, to reply i posted some ways to upgrade firmware, check my posts, i hacked a windows 10 install, and i got it running on my cube, tutorial also available.
I flashed my tablet with teclast x98 rom, touchscreen not working, i have the cube kernel, but i dont know how to inject it in teclast x98 boot.img.... so guess what ? do it for us please community !
I can not get a copy from cube
I am not able to download from their site. to much chinese even with google translate
could you give me a copy... or i can have you put it in my dropbox
thanks in advance!!
I
thermoska said:
Hello,
I was able to flash cube many times.
There is actually an update here :
http://www.51cube.com/ch/DownShow.asp?ID=364 - i used google translate to flash it successfully
however it is still android 4.4.4.
Regarding partitioninig, sure you can. You need to update partition.tbl file.
I did it. I tried to flash rom from telcast where they do have android 5. successfully.
But comparing partition tables I found out they are different, MFT did it without yelling.
Also I exchanged several files and used flash file from cube rom mentioned above, to be more specific I exchanged following files (taken from telcast 5 rom http://forum.xda-developers.com/showpost.php?p=61079769&postcount=8387)
boot.img
partition.tbl
recovery.img
system.img
However touch screen is not working, but at least I have got a boot. Thats where I end, I can not fix touchscreen drivers here, I am too dumb for that
I would appreciate if somebody would create a new rom for cube . If somebody is skilled enough, I can provide more detailed information and files I used.
Asking any further help from me is pointless, as I am not an expert and not so deep acknowledged.
Click to expand...
Click to collapse
I have tablet Teclast X10 Plus ((F2D6) Intel Z8300 Cherry Trail CPU. Android 5.1 only. Unable to find any information on how to root this device. Assistance will be appreciated. Thanking you.
Same here, no info from the company. Worse, we are theoretically supposed to be able to install Windows 10, but Teclast does not give any drivers for that. With only 2go of RAM, I don't care that much about Win 10, but not being able to root is frustrating. I've tried fastboot OEM unlock on the device, it said it worked, but it actually didn't
There's no OEM information for stock firmware flashing?
If you go there : teclast.com/en/firmware/ and type: f2d6 , then you have the only thing that they gave us, it's an Intel flash tool with the current firmware and android 5.1. I guess that there is something in there we could start with, but I'm not an expert. Other than that, the company give no support whatsoever and doesn't answer emails.
As for other information: I've tried to root with KingoRoot, it shows successful, my device rebooted, but seems to hang after the second boot stage, unable to load the O.S. anymore. I had to re-flash the device to fix it.
Somebody found a way to root: hispatablets.com/tablets-teclast/root-teclast-x10-plus-solucionado-t8419.html
I’ve never been that happy to know more than one language
If you need help with the instructions (in Spanish), just ask. I’ve tried and it’s working, my x10 plus is now rooted.
Still, the procedure is a bit clunky and I’m sure we can optimize the process (and fixed the reboot needed problem after the --daemon).
This is a good step and it seems like with this and the package given by Teclast we have enough information to do a lot of things… Still, there is work to do…
how i can get dualboot? I need windows 10 / android version but unfortunatelly i bought android only
Found a review saying this tablet has 'upside down' problem. Basically, it displays some apps upside down and there's no way to fix it.
Do you experience that too?
Flyagaric : It's not impossible, but it is super easy to fix (for those with this bug), you just choose one particular position (I suggest landscape), you go in options and lock the rotation. Every apps will properly open in the current position.