Related
Hi all,
I just want to share the solution I used to solve a big shared problem I had with my X10 Mini. During a call my battery went so down I couldn't even turn it on without any sign of hope. As we know in this cases the phone CAN'T charge itself cause it need a software "help" and without a minimal charge the phone is dead. In my case scenario even with Seus holding back the button couldn't solve it.
I decided to solve it without taking it to the 60km away SE support center and:
- taken apart a usb data phone cable
- divided the red wire and the black one
- considered that the USB port gives 5v at 0.5ma
- taken apart the phone case and the rubber cap on the top of the phone
- take out the battery wires connector from the logic board
- inserted red + wire into red hole of the battery connectore and same with the black ones
- connect it to the usb port of a spare computer (you could sacrifice it if something goes wrong)
- wait for a hour to have a good charge starting point
- disconnect everything, reconnect connector, close case and connect to the normal micro usb cable
- evrything will charge as usual.
NOTE: If someone try at his personal risk, BE CAREFUL cause if something cause wrong you could ruin battery, or logic board or pc motherboard!!!
See attachment.
Bye
Nice hack!
Thanks for sharing.
Sent from my E10i using XDA App
Good job, but did u try to charge for a few hours without SIM card? Because I already drained completly and solved problem just removing SIM, putting to charge and waiting. After 2 or 3 hours the system start to charge normally.
WTF? This phone has this problem? Did 2.1 fix it? My wife has the habbit of letting her mobiles die.
I hope that she will not need to take out the SIM card every week to charge her phone.
Thanks for the share by the way.
Yeah this phone got this problem and it's quiet usual I see in different forums. But not always it drains so much like me. I did the BIG error to try a couple of times to turn it on. I tried any combinations of tricks with or withous sims differents ones, different buttons, different charger, etc.... No way! I think that SE support centers has got some kind of charger that has got the female connector of the battery to solve this problem.
Ah I now realised you have a mini and not a mini pro, as mini pro's can have their batteries removed.
I hope I will not have to solve this problem , any time soon.
Good to know anyway.
Hi There, Does anyone know if it's possible to use the Galaxy S2 without a battery, or trick it into thinking it does have one and just run off power?
My phone works, but kills a battery in about 30 minutes. There's one resistor in there that gets super hot after being water damaged, but only with a battery in.
Wouldn't know where to buy a new resistor, so wouldn't mind leaving it permanently docked and run my audio for the house through it if I can somehow run it without a battery
.
I think it can run without battery but can't boot without battery
Sent from my sgs2 running cm9 using xda app
Makrilli said:
I think it can run without battery but can't boot without battery
Click to expand...
Click to collapse
Just tried that on another S2 I have and it didn't work
Sorry to revive a old thread, but I would also like to know if there is a way to trick the phone into booting from a power supply instead of a battery. I am attempting to hardwire an old S2 into an imbedded in car media player blah blah blah.....long story short I have issues using the battery.
If I leave the phone plugged into a constant powered USB when the car is off and the phone is sitting dormant it over charges, the battery gets super hot, I get the overcharge/overheat warning etc. If I disconnect it, then I have two issues, first it loses charge as it is in use and pulling it when I park means having to bring it inside and top it off etc. The second problem is....it kind of defeats the purpose of an "embedded system".
I have the software set up perfectly and I love the way it all works. My only current hitch is the battery issue. If I can bypass it I know I can run a off delay relay, so that when the car is shut off the USB cord stays "hot" for say 1 hour then shuts off thus removing power. This option seems tedious and the parts more expensive then a simple power supply replacement. Unfortunately I do not know the software side.
I have been able to get the phone to boot without a battery, however as soon as it is done booting I get the "battery low, plug in" warning, then a few seconds later the phone shuts off........Is there a way to keep the phone from shutting down at that point, or get it to ignore the fact the "battery" is at 0%?
Edit: When I say I can get it to boot without a battery, I am wiring a power supply directly to the two pins that the battery + and - would be touching.
techoverload said:
Sorry to revive a old thread, but I would also like to know if there is a way to trick the phone into booting from a power supply instead of a battery. I am attempting to hardwire an old S2 into an imbedded in car media player blah blah blah.....long story short I have issues using the battery.
If I leave the phone plugged into a constant powered USB when the car is off and the phone is sitting dormant it over charges, the battery gets super hot, I get the overcharge/overheat warning etc. If I disconnect it, then I have two issues, first it loses charge as it is in use and pulling it when I park means having to bring it inside and top it off etc. The second problem is....it kind of defeats the purpose of an "embedded system".
I have the software set up perfectly and I love the way it all works. My only current hitch is the battery issue. If I can bypass it I know I can run a off delay relay, so that when the car is shut off the USB cord stays "hot" for say 1 hour then shuts off thus removing power. This option seems tedious and the parts more expensive then a simple power supply replacement. Unfortunately I do not know the software side.
I have been able to get the phone to boot without a battery, however as soon as it is done booting I get the "battery low, plug in" warning, then a few seconds later the phone shuts off........Is there a way to keep the phone from shutting down at that point, or get it to ignore the fact the "battery" is at 0%?
Edit: When I say I can get it to boot without a battery, I am wiring a power supply directly to the two pins that the battery + and - would be touching.
Click to expand...
Click to collapse
bump
any solutions to this yet?
the phone has a circuit that controls power and charge level by communicating with the battery so it will always know that the battery is removed because the battery feedback circuit will not be present.
Sorry for reviving an old thread, but i have a solution that may help others out.
I have found a way to power the Galaxy S2 GT-I9100T from an external power supply ( i have also tested on S3 GT-I9300 and S5 SM-G900I).
My first step was to create a dummy battery out of perspex, you could use any non conductive material.
Make sure you include the alignment notches and keep it as close to the size of the original battery so it is a snug fit and wont accidentally fall out.
When you know the perspex fits you can start fitting the contact terminals, make sure you have the polarity correct and that they line up with the contact terminals of the original battery and the spring terminals in the phone.
Once you have the terminals fitted you can then look at powering up your phone, i used a LM2596 based DC-DC converter that i had laying around.
If you are using a variable DC-DC converter like i did make sure you adjust the output of the power supply BEFORE connecting to your phone to prevent you destroying your device.
My DC-DC converter is set at 3.88 Volts, this value seems to trick the phone into thinking it has a battery with greater than 40% charge that way you don't get the annoying low battery alerts.
Pic.1
Pic.2
Pic.3
Pic.4
Pic.5
How about taking your admittedly innovative idea one stage further.......
If you have an old battery laying around, why not (very carefully) remove the top part of it for use with your perspex replacement....this top section contains the overcharge protection circuit which would help to provide added protection to the device....it also has the benefits of the facts that the battery connection points are already in place and correctly aligned (it also has those alignment notches at either end).....imo, an improvement on an already good idea....
I got problem with my SGS 2 - after long on-shelf time battery drained to absoltely zero. My voltometer showed 0 on every connector. I was unable to charge or boot my phone (24h+ on charger, no signs of life). Dead, bricked, gone... Battery was relatively new (some months) so I didn't want to buy another one. Then I read Spud2233's post... and tried it .Well, kind of variation. I connected charger to phone's USB port and additional power (Motorola's dual port charger) to internal batterys connector (simly stripped old USB cable). Then battery was inserted and.... voila! After 2 or 3 retries my phone booted in and started to charge. I disconected additional power cable, phone is loading as usual. Battery revived!
Thanks for inspiration, Spud2233!
szydas said:
I got problem with my SGS 2 - after long on-shelf time battery drained to absoltely zero. My voltometer showed 0 on every connector. I was unable to charge or boot my phone (24h+ on charger, no signs of life). Dead, bricked, gone... Battery was relatively new (some months) so I didn't want to buy another one. Then I read Spud2233's post... and tried it .Well, kind of variation. I connected charger to phone's USB port and additional power (Motorola's dual port charger) to internal batterys connector (simly stripped old USB cable). Then battery was inserted and.... voila! After 2 or 3 retries my phone booted in and started to charge. I disconected additional power cable, phone is loading as usual. Battery revived!
Thanks for inspiration, Spud2233!
Click to expand...
Click to collapse
Just registered to say thanks for this tip!
I too have had SII batteries go dead after too long, and the SII seems to be unable to power up without a voltage across the battery terminals.
I used a small variable power supply set to about 3.5 V. I trimmed some thin hookup wire until only a few strands were left and 'pinched' them between the battery terminals and the phone battery contacts. Then with a charger plugged in to the phone I was able to 'trick' the phone into turning on. Once booted the battery charged fine.
Note I think this should be done quickly as the phone and power supply will fight each other for as long as the voltage is placed on the contact, so I pulled the PS wires out (keeping the battery in) as soon as the phone was booted up.
szydas said:
I got problem with my SGS 2 - after long on-shelf time battery drained to absoltely zero. My voltometer showed 0 on every connector. I was unable to charge or boot my phone (24h+ on charger, no signs of life). Dead, bricked, gone... Battery was relatively new (some months) so I didn't want to buy another one. Then I read Spud2233's post... and tried it .Well, kind of variation. I connected charger to phone's USB port and additional power (Motorola's dual port charger) to internal batterys connector (simly stripped old USB cable). Then battery was inserted and.... voila! After 2 or 3 retries my phone booted in and started to charge. I disconected additional power cable, phone is loading as usual. Battery revived!
Thanks for inspiration, Spud2233!
Click to expand...
Click to collapse
Thank you so much for the solution to my problem! I have purchased TWO batteries already and they both stopped working after drained to zero. I was blaming a charger or a quality of the battery. I found other posts suggesting to remove a capacitor but it wasn't broken...
Thanks to you, I have just booted my phone, pulled out extra power after couple minutes and it charging on its own now! (well 5% as I speak).
fpN3eqU said:
Just registered to say thanks for this tip!
I too have had SII batteries go dead after too long, and the SII seems to be unable to power up without a voltage across the battery terminals.
I used a small variable power supply set to about 3.5 V. I trimmed some thin hookup wire until only a few strands were left and 'pinched' them between the battery terminals and the phone battery contacts. Then with a charger plugged in to the phone I was able to 'trick' the phone into turning on. Once booted the battery charged fine.
Note I think this should be done quickly as the phone and power supply will fight each other for as long as the voltage is placed on the contact, so I pulled the PS wires out (keeping the battery in) as soon as the phone was booted up.
Click to expand...
Click to collapse
szydas said:
I got problem with my SGS 2 - after long on-shelf time battery drained to absoltely zero. My voltometer showed 0 on every connector. I was unable to charge or boot my phone (24h+ on charger, no signs of life). Dead, bricked, gone... Battery was relatively new (some months) so I didn't want to buy another one. Then I read Spud2233's post... and tried it .Well, kind of variation. I connected charger to phone's USB port and additional power (Motorola's dual port charger) to internal batterys connector (simly stripped old USB cable). Then battery was inserted and.... voila! After 2 or 3 retries my phone booted in and started to charge. I disconected additional power cable, phone is loading as usual. Battery revived!
Thanks for inspiration, Spud2233!
Click to expand...
Click to collapse
I am in the same situation with SII batteries go dead after too long.
I do not understand this part
''I connected charger to phone's USB port and additional power (Motorola's dual port charger) to internal batterys connector (simly stripped old USB cable). Then battery was inserted and.... voila!''
or this part
'' I trimmed some thin hookup wire until only a few strands were left and 'pinched' them between the battery terminals and the phone battery contacts. Then with a charger plugged in to the phone I was able to 'trick' the phone into turning on.''
how is this different than inserting the battery in the phone and then connecting the usb power supply?
blue whale said:
how is this different than inserting the battery in the phone and then connecting the usb power supply?
Click to expand...
Click to collapse
The phone won't charge the battery if it doesn't detect (sufficient) voltage. You can "jump start" the charging process by tricking it with a fixed voltage across the terminals.
so I take my dead battery, then
-take a usb charger+usb cable
-strip the usb cable to get two strands
-put one strand of the usb cable on the + of the battery
-put one strand of the usb cable on the - of the battery
=>the battery is charging
[or easier, I take battery like this,
put one strand of an electric cable on the +, connect this cable to the + of the phone battery, then put one strand of the electric cable on the - of the battery and the - of the phone battery
then I put the battey in the phone with usb power supply IN and the phone boots ???
I wouldn't use a USB cable, 5 V is probably too high.
blue whale said:
or easier, I take battery like this, put one strand of an electric cable on the +, connect this cable to the + of the phone battery, then put one strand of the electric cable on the - of the battery and the - of the phone battery then I put the battey in the phone with usb power supply IN and the phone boots ???
Click to expand...
Click to collapse
Yep, that's exactly what I did (except I used a 3.5 V power supply).
Once the phone has begun booting you should probably disconnect the "jump start" battery as quickly as possible or it'll fight the charging circuit.
fpN3eqU said:
I wouldn't use a USB cable, 5 V is probably too high.
Yep, that's exactly what I did (except I used a 3.5 V power supply).
Once the phone has begun booting you should probably disconnect the "jump start" battery as quickly as possible or it'll fight the charging circuit.
Click to expand...
Click to collapse
but you agree that connecting the phone battery the charged green battery is like charging the phone battery [at least a bit]?
then I would just use the phone battery normally, by inserting it into the phone and boot the phone and finish to charge the phone battery.
blue whale said:
but you agree that connecting the phone battery the charged green battery is like charging the phone battery [at least a bit]?
then I would just use the phone battery normally, by inserting it into the phone and boot the phone and finish to charge the phone battery.
Click to expand...
Click to collapse
Not really, the SII battery will still be dead after a few seconds "charging". Getting the voltage across the phone battery terminals tricks the phone that there's a charged battery present so it will boot and continue charging it. Otherwise it gets stuck in something like a boot loop looking for the battery (mine did anyway).
If you could charge it separately from the phone then obviously you'd just do that.
Thank you for all your tips. I tried similar stuff, but I guess the voltage was just not right.
So I asked around to get a spare battery, which which I powered on the phone. It worked like charm.
I change the battery while the phone was running and tada! my phone was loading the "out of order" battery just fine.
Pretty much the same trick you guys did, but with less soldering and more quick magic happening ^^
regsnerven said:
Thank you for all your tips. I tried similar stuff, but I guess the voltage was just not right.
So I asked around to get a spare battery, which which I powered on the phone. It worked like charm.
I change the battery while the phone was running and tada! my phone was loading the "out of order" battery just fine.
Pretty much the same trick you guys did, but with less soldering and more quick magic happening ^^
Click to expand...
Click to collapse
I did just that to my s2 and his dead battery.
I was scared to go with ONLY a 18650 battery to charge the dead battery (no phone or usb charger involved) : I did not know if I should connect pole+ of the 18650 with pole + of dead battery (and pole - of 18650 with pole - of dead battery) which is the parallel scheme or the opposite, to go with the ''series'' scheme
blue whale said:
I was scared to go with ONLY a 18650 battery to charge the dead battery (no phone or usb charger involved) : I did not know if I should connect pole+ of the 18650 with pole + of dead battery (and pole - of 18650 with pole - of dead battery) which is the parallel scheme or the opposite, to go with the ''series'' scheme
Click to expand...
Click to collapse
You were right to be scared. You should not do that. The dead battery might draw too much current. That could be dangerous. Read a bit about how charging of Li-Ion batteries works: first you charge with constant current (CC), which depends on the battery's design, once it reaches the correct voltage (4.2 V for a single cell), it should go into constant voltage mode, and then you have to know at what time or remaining current you shut the charger off. A good rule of thumb is to wait till the current drops to 10% of the charging current. E.g. if you were charging the battery with 1 A***, you should turn off the charger when it's down to 100 mA.
***1 A is just an example that would work for most modern phone batteries. However, this can be different! Ideally it's written on the battery.
Also, it's very well possible that in newer phones the battery will only output voltage if the charging circuit inside the phone allows it to. At least that's the case in notebooks for many years, and I don't see why it should be very different for phones.
Hello all!
I recently purchased a used Droid Razr Maxx from a co-worker. The lcd screen was cracked so I replaced it. I took apart the phone completely and reassembled it with the new screen in place. The phone turns on just fine, the Motorola icon shows up and it gets to the charging battery icon with 5%, but after a few hours of letting it charge, it stays at 5% and wont turn on. Keep in mind, the phone has been charging for two hours from the time this post was made.
My question is, did I somehow damage the battery when operating internally? I can replace the battery if needed.
Another question. If I damaged the motherboard, would the phone turn on at all?
I am kind of wondering if there is a certain thing I needed to do before plugging it in.
To answer any questions that might be asked: The battery was completely dead when I did repair the screen. The charger is a wall usb charger, not plugged into my computer. I did place all the components inside the phone, to the best of my knowledge. I have had experiences when it comes to internal repair.
check for how long this 5% charge remain. it usually happen due to problematic battery guage
faheemakbar18 said:
check for how long this 5% charge remain. it usually happen due to problematic battery guage
Click to expand...
Click to collapse
Morning now. The battery is still at 5%. The phone shuts off soon as the charger is not connected. Does not seem to hold a charge. Think I should buy a new one?
Garret27 said:
Hello all!
I recently purchased a used Droid Razr Maxx from a co-worker. The lcd screen was cracked so I replaced it. I took apart the phone completely and reassembled it with the new screen in place. The phone turns on just fine, the Motorola icon shows up and it gets to the charging battery icon with 5%, but after a few hours of letting it charge, it stays at 5% and wont turn on. Keep in mind, the phone has been charging for two hours from the time this post was made.
My question is, did I somehow damage the battery when operating internally? I can replace the battery if needed.
Another question. If I damaged the motherboard, would the phone turn on at all?
I am kind of wondering if there is a certain thing I needed to do before plugging it in.
To answer any questions that might be asked: The battery was completely dead when I did repair the screen. The charger is a wall usb charger, not plugged into my computer. I did place all the components inside the phone, to the best of my knowledge. I have had experiences when it comes to internal repair.
Click to expand...
Click to collapse
It could be a faulty charger.
Normally, If the battery is poor, it won't hold charge but it won't stick to a particular percentage. It will only discharge sooner. But given the fact you got the phone dead, it might as well be the battery.
Worst scenario, you damaged the charging port.
I'd begin with using a different charger, if that doesn't work, try another battery.
neo.ank said:
It could be a faulty charger.
Normally, If the battery is poor, it won't hold charge but it won't stick to a particular percentage. It will only discharge sooner. But given the fact you got the phone dead, it might as well be the battery.
Worst scenario, you damaged the charging port.
I'd begin with using a different charger, if that doesn't work, try another battery.
Click to expand...
Click to collapse
I have used other chargers and they all work for my other phones, just not this one. I am hoping it's a dead battery and not something to do with the motherboard. My friend wont let me dismantle his phone to see if it's the batter, lol.
Just the clarify, the phone doesn't boot up completely, only to the charging screen. The battery icon with 5% shown. When I unplug the phone from the charging screen, it just dies. Will not even boot up to the phone animation.
I purchased a battery replacement off of Ebay. It'll arrive in a few days. Let's hope this works!
Still could be the charger. Did you check voltage and amp specs? 850amps 5.1v
This phone can be picky. First razr I got had broken screen, repaired it and found myself in the same situation.
Connecting to a laptop would not charge it. Only stock charger. IPhone charger or chargers designed for iphones will not work.
Edit: When replacing battery, position is critical. If battery terminals are a little bit displaced it will not turn on.
Displacement can be minimal or imperceptible but will cause troubles. If possible don't place cover before checking that it turns on. (please avoid touching circuits or battery terminals or will get worse).
Sent from my XT910 using xda app-developers app
angrist said:
Still could be the charger. Did you check voltage and amp specs? 850amps 5.1v
This phone can be picky. First razr I got had broken screen, repaired it and found myself in the same situation.
Connecting to a laptop would not charge it. Only stock charger. IPhone charger or chargers designed for iphones will not work.
Edit: When replacing battery, position is critical. If battery terminals are a little bit displaced it will not turn on.
Displacement can be minimal or imperceptible but will cause troubles. If possible don't place cover before checking that it turns on. (please avoid touching circuits or battery terminals or will get worse).
Sent from my XT910 using xda app-developers app
Click to expand...
Click to collapse
That was exactly the problem....
I got the new battery, but not 24 hours later, I was realigning the cables inside it (like the front facing and rear cameras, along with the WiFi antenna) I slightly moved the replaced battery and the cable to the battery to the motherboard tore itself. After a long face-palm moment, I got the old battery back in place and realigned it very carefully. It turns out it still works, but I am out a new battery.
Apart from the battery, I need to find out why the front speaker won't work. Either the speaker is damaged or something needs to be in place correctly, besides the cable. Also need to get some adhesive gel to bond the screen and case together.
Damn I really had forgotten about that speaker. The fact is it tends to break. It has very fine copper wire winding that can break when you remove it the wrong way.
Having no experience I pulled not knowing that speaker is glued to motherboard. At that time I didn't knew it and thought that little bar left was part of the motherboard.
Since you disassembled almost everything, that must be the reason it is failing. If it is not that, it is badly plugged but I really doubt it.
Alas Never fixed it, so i can't tell correct process to reassemble or disassemble that speaker. Instead I searched for apps that would activate loud speaker automatically during calls.
Would have been nice to fix it but I got the opportunity to acquire a RAZR maxx so never touched and sold instead.
Removing that glue might involve using a hot air gun. So that you don't damage motherboard removing by force. (But again too much heat could Fry motherboard)
Maybe someone could share it's experience?
About that screen, Remember to have read about a 3m adhesive spray in some thread.
Also some one just passed hot air that melted original glue but it would be better not to play with heat over a battery.
Sent from my XT910 using xda app-developers app
Hi there, XDA folks!
Mario here with some phone problems..
I have a CDMA Evo 3D running on the stock ROM.
The phone's charging cable was shorting out ever since I bought it (got it 2nd hand). I had to wiggle it in order to get the phone charging.
I gave it to my girlfriend to use it for taking pictures n whatnot while outside of town. She returned it kinda Rambo-ish; the front of the phone basically fell apart.. the front metal grill surrounding it, at least.
Phone worked fine, except for the cable shorting out even more. My laptop shut down every time that happened, so I'm quite sure that's not what caused the problem I'll be explaining later on in this thread.
So let's get to the point, shall we?
My phone was really low on battery, something within the range of 2-5%. I tried charging it, but the wires shorted out again and the laptop died on me.. again, and again, and again..
I couldn't really bother with fiddling around with it until it starts, so I just unplugged it and left it that way.
The phone sat for a few days, my (main) laptop broke, so I decided to give the good ol' Facebook Messenger a go.. sadly, the phone would not turn on or start charging.
I removed the shrink-like wrap around the wires of the USB cable, cut the bad parts and twisted the color-matching wires in order. Sadly, the phone would still not charge.
I tried with another (self-made) USB cable... no luck whatsoever. Just to clarify; the blue wire on the one the phone comes with is ground, right? If not that could of caused the problem, since I connected the blue wire on the mini-usb to the black one on a standard USB plug.
I tried juicing the phone up a tad bit by running 5V on the battery for 15 minutes or so.. didn't really bother going for more, since it's kinda hard to keep 2 wires pressed against the battery for more than that. The phone powered up, but the display did not. There was the low battery sound, volume keys were functional, vibrating feedback was okay.. hell, the phone even took a screenshot when I pressed power button + volume down!
Sadly, that didn't solve anything.. even turned on, it would not charge. The 15-minute charge is good for a minute of red blinking light and fancy glowing buttons, nothing more.
Is the phone dead, or should I give it a hour charge directly and see how that goes?
Thanks in advance to everyone who replies!
i think it'll be good if you buy a universal battery charger for phone. so you can charge your battery without plugged to the phone
apinghed said:
i think it'll be good if you buy a universal battery charger for phone. so you can charge your battery without plugged to the phone
Click to expand...
Click to collapse
I am looking for more opinions before I spend cash I don't have on chargers that may not work.
If you or someone else is positive about the display not working because of not enough battery juice, then I'll manually charge the battery for an hour, even though it's uncomfortable as hell to hold 2 wires on the pins for that long.
What's bugging me is that it's not charging once it has just enough juice to power up everything, no display either. I'd like to know if it's doing that, because the battery is too dead to actually start charging up via the phone and whether the display just doesn't work or there's not enough juice for it.
Edit; I bought a chinese charger that charges the battery directly (2pins). The display still does not work and the phone will still not charge via the cable. Could it be a bad cable (and a dead display..)? It seems like the phone itself is responsive - I unlock it, press the "search" button and when I type on the keyboard (that I don't see), it vibrates with every pressed key.
Also, I can hear it taking a screenshot and the volume down/up buttons seem to be working fine.
Dontrememberusername said:
Edit; I bought a chinese charger that charges the battery directly (2pins). The display still does not work and the phone will still not charge via the cable. Could it be a bad cable (and a dead display..)? It seems like the phone itself is responsive - I unlock it, press the "search" button and when I type on the keyboard (that I don't see), it vibrates with every pressed key.
Also, I can hear it taking a screenshot and the volume down/up buttons seem to be working fine.
Click to expand...
Click to collapse
this is exactly what's been going on with my phone as of a few days ago.
checked the time while it was plugged in, unplugged it...screen froze.
hasn't turned back on since.
the buttons on bottom light up, though.
i can take calls, use my unlock pattern (it takes me a few tries now that i can't see anything) and press the search key for google now.
for all intents and purposes...phone's fully functional...except i can't see anything going on.
i brought my phone into a sprint corp store, they changed the top housing for me screen and all for free.
it was really nice.
but, that didn't change anything.
screen still doesn't change anything.
they said the board probably shorted on screen lead.
have you figured anything out?
cipher77 said:
this is exactly what's been going on with my phone as of a few days ago.
checked the time while it was plugged in, unplugged it...screen froze.
hasn't turned back on since.
the buttons on bottom light up, though.
i can take calls, use my unlock pattern (it takes me a few tries now that i can't see anything) and press the search key for google now.
for all intents and purposes...phone's fully functional...except i can't see anything going on.
i brought my phone into a sprint corp store, they changed the top housing for me screen and all for free.
it was really nice.
but, that didn't change anything.
screen still doesn't change anything.
they said the board probably shorted on screen lead.
have you figured anything out?
Click to expand...
Click to collapse
Nope, I'm still in the same situation.
Does yours charge?
My phone isn't recognized by my laptop at all, so I'm guessing something is indeed fried. I don't have the appropriate screwdrivers to open it up and inspect the board, otherwise I'd open it up and check it out.
If you have Torx T5 & T3 screwdrivers you should give it a go - post some decent-res pics over here and I'll at least visually inspect it.
I genuinely don't feel like spending more money for tools n whatnot for a phone that may be permanently dead.. planning on getting a second-hand S4 anyways. Waiting on a student loan and smashing this phone to pieces as soon as I get the cash for a new one. Can try and help out for yours if you manage to open it, though. Could be something as simple as a dead resistor that shouldn't be too hard to replace.
I tried the hillbilly method and hit my phone a few times against a wooden bench, that didn't seem to fix it. Pretty positive something's fried, but I'm also guessing it isn't a viable component, having in mind the phone functions normally, even though the display & usb port don't work.. hell, my phone woke me up at 3AM today, 'cause the alarm went off, lol!
Hi,
I had a Sony Z5 compact in a drawer for about 2 years, where the battery already was weak. I'd like to use it as a smarthome button panel where the bad battery won't matter, but I can't get it to turn on anymore.
When I first plugged it, the status LED switched to constant red. I unplugged it a couple hours later, just to find, that the LED stayed on even when unplugged. The device still was cold, so I don't think, that it really charged.
Since there was no reaction on the power button, I tried the "OFF"-button in the SIM slot. After reading on the internet, I held that button for 2 minutes. The phone vibrated every 15s, so it seemed alive. I then plugged in the charger, again the status LED turned constant red. This time the device got warm, seemingly charging.
After a couple of hours I tried starting it, but still, theres no reaction on the Power button. I again tried the OFF button, with no reaction whatsoever, not even vibrating anymore. Also the status LED shows no more reaction on plugging it in.
Is the device dead now? Anything I can try to get it working again? I don't need the battery anymore, Its supposed to spend its second life permanently plugged in.
best regards,
RockNLol
The usual advice is to make sure it is off (Hold power and vol-downup until it vibrates 3x / if really dead, just wait ~20s), and then leave it on a charger for a few hours. If that doesn't do it, your battery is toast.
Even if it is revivable, there is a chance that it is so weak that it will make the phone crash - the battery is used like a buffer even when on the charger, and if the phone needs high peak current, it will try to take it from the battery. If the battery is too weak, voltage will drop and the phone will crash.
In any way, I would not want a battery that is potentially damaged to be at the charger 24/7. If you deep-discharge a battery, it can form tiny little short circuits, and if you charge it, it can become a fire hazard. As in, burn your house down and release lots of toxic fumes while doing so.
If you are familiar with soldering, the best solution would be to open the phone, remove the battery, and replace it with a fake battery circuit. Obviously, don't do this if you aren't comfortable doing this kind of stuff, and always have a plan for what to do if the battery decides to light on fire.
For that, after you removed the battery, try to pry off the yellow tape on it, and get to the battery protection PCB near the connector. Carefully cut the leads to the actual battery and remove it (this is the most dangerous part). Then, solder a large capacitor across the battery leads and a connector for a power supply that can provide around 4V at, idk, 2-3A. There aren't many 4V power supplies, but a 5V one and a (silicon) diode in series work well (make sure the diode can survive a couple amps). Then, plug the fake battery back into the mainboard, fix everything in place using tape or glue, and see if it boots.
1ggn3 said:
The usual advice is to make sure it is off (Hold power and vol-down until it vibrates 3x / if really dead, just wait ~20s),
Click to expand...
Click to collapse
Power and Volume-Up?
Sure, one of the two
Power + Volume-down starts TWRP when the device is not running.
When the device is running, it takes a screenshot.