Hello,
i searched a lot of unbrick a HTC Desire X but nothing helps.
The phone was ok the last times, i charged it normaly over the night, in the morning i take my phone and see black screen oO. The Red/organe LED is still on. So ok powerd on, nothing happens .................
I think its bricked, but i dont now why. So ok, i thing i had successfully recoverd more times my LG, so i can recover the Desire too.
No, i can´t ....
I connected the phone via USB to the PC, i onbly found a Qualcomm HS_USB QDLOADER 9008 COM 5.
Driver installed, QPST downloaded.
So the Programm told me the Phone is now in Downloadmode.
and i see Phone Q/QCP-xxx(Download)
I think i need a new bootloader, so i searched but i need it in HEX Format or anything else.
Can anyone help me, so fast you can .....
MasterTobi said:
Hello,
i searched a lot of unbrick a HTC Desire X but nothing helps.
The phone was ok the last times, i charged it normaly over the night, in the morning i take my phone and see black screen oO. The Red/organe LED is still on. So ok powerd on, nothing happens .................
I think its bricked, but i dont now why. So ok, i thing i had successfully recoverd more times my LG, so i can recover the Desire too.
No, i can´t ....
I connected the phone via USB to the PC, i onbly found a Qualcomm HS_USB QDLOADER 9008 COM 5.
Driver installed, QPST downloaded.
So the Programm told me the Phone is now in Downloadmode.
and i see Phone Q/QCP-xxx(Download)
I think i need a new bootloader, so i searched but i need it in HEX Format or anything else.
Can anyone help me, so fast you can .....
Click to expand...
Click to collapse
Did you try to pull battery? Just pull battery, wait for the orange LED to go off and and put it back in, then boot normally. Should work.
dansou901 said:
Did you try to pull battery? Just pull battery, wait for the orange LED to go off and and put it back in, then boot normally. Should work.
Click to expand...
Click to collapse
still the same, nothing boots
MasterTobi said:
still the same, nothing boots
Click to expand...
Click to collapse
I'm afraid it's classified as paperweight then... The only option is to repair via RIFF Jtag Box...
MasterTobi said:
still the same, nothing boots
Click to expand...
Click to collapse
You just charged without doing anything before it went to charged?
Try to leave the phone for a couple hours and try again, I think the battery overheated
If that doesn't work than it's paperweighted
Related
Hey guys, I'm new to this site and I hope this is being posted in the correct area and I apologize if it's not.
Anyway, I have an LG Access 4G LTE StraightTalk android phone. The other day, I rooted it and everything worked fine and I was having a good time editing things and customizing. Last night, I download the Clockwork Recovery Mod app and my intention was to reboot into the CWR mode and install a zip file for a custom animation, (and yes, I know how simple it is normally, but this one required extra steps). Now, seeing as my phone is relatively new (February 2014 release) I figured I could've gotten a recovery module from a similar phone. Wrong! I'm pretty sure there was a warning that advised against it, but I didn't listen. I clicked "reboot into clockwork mode" and my phone screen went black and hasn't come back on at all. No power buttons, or combinations will work. However, when I took out my battery and plugged in my charger, it shows an empty battery with a charger plugged in and a large yellow triangle with a question mark in it. While it is in this state, if I hold the power on button or any other sequences, the screen goes black and displays the same symbol again. When I plug the battery into it, the symbol goes away, and nothing happens. Although, when I plug it into my computer with the battery inside and all, I can hear my computer making the "something is connected sound" then like 10 seconds after, "something was disconnected". You know, like when you plug and unplug a flash drive or something. It's also worth noting that I don't have an SD Card so all of my rooting and download was done onto my internal memory....... I'm boned right now. Can anybody help?
the same problem
I do some experiments with this phone to unlock
This phone realy is LG F70 D315
I stuck in Qualcom 9008
http://forum.xda-developers.com/lg-g2/help/lg-f70-d315-tracfone-download-mode-t3009244
Depending in what stage you leave it
what you see when conect to computer in the device manager?
corratge said:
I do some experiments with this phone to unlock
This phone realy is LG F70 D315
I stuck in Qualcom 9008
http://forum.xda-developers.com/lg-g2/help/lg-f70-d315-tracfone-download-mode-t3009244
Depending in what stage you leave it
what you see when conect to computer in the device manager?
Click to expand...
Click to collapse
I think you're confused. My phone won't turn on at all. The screen is black and it will not power on. I don't see anything in the device manager when it's plugged in. My laptop makes the sounds but nothing happens. And I read your post and to confirm, we both have the Straight talk LG F70, also known as the LG Access 4g LTE. So we have similar situations with the same phone.
Sorry I don't understand why you say i confused maybe my english is'nt good enought
My phone won't turn on at all even not batery image but in the device manager
I have Qualcomm, HS-USB QDLoader 9008
I break my phone because I do worst experiments and I know the consecuencies
I backup all original partitions I can give you if you find the way to restore it
this phone and all qualcom from nowdays has 2 dead modes 9008 & 9006
In this post explained
for the mode 9008 the oficial tool for all is QPST
rusian post about
If you check that nothing in the device manager you can have QHUSB 9008 mode but i cant do anything in it for the moment this mode is really hard to work it
The test point for this LG to force in 9008 go in atachment.
The only form I know to save your phone If you achived somethink like a disk with ext partitions that windows don't recognize when you conect to pc
I have the original recovery and then you flash it
I flash a custom recovery but this don't break the phone exept the recovery because
you have to unlock bootloader to do this and i did'nt
Also for a custom animation the only needed is root and is stored in /system/media/bootanimation.zip
Is there a thread for this phone anywhere?
Found one last night in a car I just bought, it is locked with PIN, no SIM card was dead so not a current phone and dude hosed me on car deal so a toy for me...
Wanted to at least get into phone to see if could get my active Tracfone SIM to use their network, phone died that it was in, if I could force my way into it somehow or figure out how to hard reset I would be in a much better place than I am now... Any other pages to look for help, or you guys know anything?
Tried the basics, power and - volume, just a reboot loop...
hey guys how i can enter recovery on my lg l31l or f70
So I rooted my HTC ONE S (villec2) today, and I wanted to flash a custom rom on it. I got a recovery (turned out to be a bad one, but it worked either way.... I noticed way too late it was made for HTC One M8) I got TWRP 2.7.1.0 and I got it working on my phone. I then backed up the system, and realized I messed up the recovery. In the meantime I got a CM 12.1 img on it and wiped the thing. The wipe removed the old Android system and the CM I downloaded was a bad download. If I go to recovery in the bootloader, it will just do the HTC white screen with "Entering Recovery" and the red warning logo but it won't get anywhere. It's just stuck there. So now, I'm stuck with a device that won't boot normally - just stuck on the white HTC screen, will boot into bootloader, and I want to know if there's a way of accessing the internal storage without being in the operating system. The worst thing is, there's no external SD Card, all just internal... Please god help me. I'm really stressing out about this since it's the only phone I have and if I lose it.... well I'm practically f-ed.... :crying: I know that I messed a few things up really badly and I'm not sure what state the phone is in.
Also just to add, the phone is barely loading up right now. I'm really scared since it's my only phone and it won't even boot normally right now. It's really acting strange, it was on 90% battery but now it might just be dead... i don't know.... someone please help
I honestly think I screwed it up.... All it does now is just a white flash / flicker when I hold the power button (both only power button and vol down) and that's it. I'm really disappointed right now but oh well.... Maybe just because the battery is not charged.... Also been looking around the other threads and looks like a lot of people had the same issue but with 0 replies...
hi friend
i ve bricked a phone once and i recover it with flashing stock rom
did you try the stock rom ?
cazawiman said:
hi friend
i ve bricked a phone once and i recover it with flashing stock rom
did you try the stock rom ?
Click to expand...
Click to collapse
I have no way of trying the stock rom. I cannot access the phone itself because I deleted the OS. There's a weird thing, that if I plug the USB to the computer, it does the connect windows sound but the phone's internal storage is still not accessible.... So as it turns out I can get to the freaking bootloader but then it just turns off with a white flicker a second later.... I have no clue what to do :crying:
try to hook your device with windows and hold the Volume Down and Power
to see if it can detect it
cazawiman said:
try to hook your device with windows and hold the Volume Down and Power
to see if it can detect it
Click to expand...
Click to collapse
Alright. I slept through the night and now I'm here trying to resolve this again. Status now, is that when I try to boot it up, it just shows a white flicker and won't turn on. no matter if i try to boot in bootloader or normally. The device doesn't appear to be charging when I plug it in because it doesn't show the LED light for charging. I think it's hard bricked. I tried other threads, showing bright light to the proximity sensor, but nothing happened.
//edit// - My bootloader was unlocked, and I was on S-ON (HTC ONE S, S3 villec2) that might change on your phone and might make the process different
So I fixed it. I will leave the tutorial for anyone in the future that might be having the same issue. If you "locked yourself out" of your system, eg. no OS, and broken recovery just plug it into the computer, try somehow getting into bootloader, go into fastboot and plug the usb cable to your computer so you're in Fastboot USB. Then you can flash a recovery on the phone using a fastboot command. I believe it's fastboot flash recovery _filename_. Just google that, there'll be plenty. Then you have the recovery and you're back on track. After that you can get the rom you wanted. Just don't make my mistake, and check if your device is exactly the same as the files you're downloading for it. I messed up there . Anyway, good luck everyone!
t
yea
Happy to hear that u have fixed your phone add "solved " to the title and add a fast tutorial for help purpose
Sent from my thl T6 pro using XDA Free mobile app
The phone told me there was a new update I started to install it, got to reboot and now is just on the elephone logo which comes every 20 sec and goes again. I cannot turn the phone off or do anything with it. Any help please
For me just shut down the phone and then reiniciat the phone ....work for me....
Enviado do meu thor através de Tapatalk
same problem here.. wtf nice update elephone, we cant be the only ones right?
now stuck on logo, restarting every 3 seconds with 100% battery...i m not even sure it will work again if battery is drained out
i can do nothing, no trys to get in factory mode or shut the phone down worked..
stuck on elephone log after upgrade
My elephone P9000 is now cycling the elephone logo every 8 seconds or so after the latest audio upgrade... It will not switch off or do anything else. Did you solve the problem. Or anyone else help. Can you share with me? Thank you.
same problem here.. wtf nice update elephone, we cant be the only ones right?
now stuck on logo, restarting every 3 seconds with 100% battery...i m not even sure it will work again if battery is drained out
i can do nothing, no trys to get in factory mode or shut the phone down worked..
Click to expand...
Click to collapse
so my battery was fully empty now.. i even pressed the power button 100 times after the battery was empty, to make sure all current is out of the phone.
plugged in charger... after 10 seconds phone start itself (after viewing the picture of empty battery) and elephone logo shows short and then back to showing picture of empty batterie cycle. After some minutes, and battery is loaded a little bit, elephone logo cycles again.
So rest in piece my p9000, i can nothing, i cant do anything from my pc because its only starting for like 5 seconds, i cant shut it down because of that and i cant get in factory mode
i am so pissed right now
just wanted to install the new update, everything worked fine like all the times before that and now my phone is ready for the trashcan.
Is there any way to reset the software without getting in factory mode?
Reset from sp flash tools?
Pro4TLZZ said:
Reset from sp flash tools?
Click to expand...
Click to collapse
the phone turns on and off in a cycle of 5 seconds, so that wont work
and i cant stop that cycle.
even if battery is 0% (i even press power button many times so really its drained out). If i recharge it, the cycle starts again without me doing anything. The Power button is not broken or something. it all began after i started new ota update and the phone rebooted like "mkitty" has the same problem it seems
Same for me, I have no idea how to restart my phone. And i dont want to loose all data I have on it.
have you tried to hold the volume up and power at the same time during the restart process to try and force recovery?
xvicedice said:
have you tried to hold the volume up and power at the same time during the restart process to try and force recovery?
Click to expand...
Click to collapse
Hello,
Yes . I have tried that.
I have a list of options that come up on the screen.
I have tried them apart from the wipe data/factory reset.
But it is still the same result.
Thank you for help.
Any more ideas?
what OTA update version did you update?
Simplytouched said:
what OTA update version did you update?
Click to expand...
Click to collapse
It said something about wifi and audio update. I followed the instructions as per a previous update (which worked OK). I never took notice of any version numbers etc.
I have all I need to flash a new rom to the bricked phone but when I connect the off phone to my pc the usb not recognised comes up and I cannot flash the rom to the phone. and yes I have the mediatek vcom drivres install. Why did I buy a Chinese phone elephone p9000 please stay well away from it. on paper is a great phone but in reality does not perform in any sense, battery only lasts 7 hours if I was lucky camera crap, gps works most of the time all that ram and power and t struggles with some videos o dear god. never again. now I cannot even read what I have on the sd cos is formatted for the phone.
juka1 said:
I have all I need to flash a new rom to the bricked phone but when I connect the off phone to my pc the usb not recognised comes up and I cannot flash the rom to the phone. and yes I have the mediatek vcom drivres install. Why did I buy a Chinese phone elephone p9000 please stay well away from it. on paper is a great phone but in reality does not perform in any sense, battery only lasts 7 hours if I was lucky camera crap, gps works most of the time all that ram and power and t struggles with some videos o dear god. never again. now I cannot even read what I have on the sd cos is formatted for the phone.
Click to expand...
Click to collapse
Its actually a great phone. Do you have twrp installed and can you get access to it? You could always boot into twrp transfer over the ROM and install it from there. If you have installed the vcom drivers then when the USB not recognized alert pops up. Go to settings and device manager. Right click the unknown device and click let me pick driver. You should be able to install it from there
The only thing I can suggest is to take the back panel of and unplug the battery. There videos on how to do this if you search YouTube or the forum. Effectively you perform a hard reset of the phone.
If and when you do get it working just twrp installed and do a backup of the whole phone working before performing any future upgrades or Rom changes. Its just better safe then sorry.
thenk you very much for that
The problem is that when I connect the phone on the off to the pc starts again the cycling through the elephone logo so the pc sees the phone for a few seconds in which does not recognises it and then is like the phone goes off until the next cycle so no time to go to device manager and install manually. but thank you for the comment.
removing the battery will void the warranty. I had the phone only since may.
It's unlikely it really matters. Your phone seller not going to take it back or fix it for free just because it's bootlopping. Well they may so just ask them. If you can't get it into recovery then a battery disconnect or contact your seller are your options
thank you
Android-UK said:
It's unlikely it really matters. Your phone seller not going to take it back or fix it for free just because it's bootlopping. Well they may so just ask them. If you can't get it into recovery then a battery disconnect or contact your seller are your options
Click to expand...
Click to collapse
I can get it into recovery mode but I haven't got any software install in the sd card to do a recovery that is why I thought my only option was the sp flashing tool and the room which I have
juka1 said:
I can get it into recovery mode but I haven't got any software install in the sd card to do a recovery that is why I thought my only option was the sp flashing tool and the room which I have
Click to expand...
Click to collapse
Well in that case all you need is a stock rom and yes just flash them with sp tools and it should start booting again. The fact you can get to recovery is a good sign.
Android-UK said:
Well in that case all you need is a stock rom and yes just flash them with sp tools and it should start booting again. The fact you can get to recovery is a good sign.
Click to expand...
Click to collapse
sorry for all of this and thank you very much for your help but when I put the phone in recovery mode by pressing the down volume and power key and connect the phone to the pc it is not recognized by the pc so I can't flash the room
Hi, i use the latest CM ROM for K910 for a quite long time. yesterday i dropped my phone and it crack my screen. was sending it for repair and now the phone wont load normally and it stays in CM loading screen and never boot up. With the cracked phone i use it for a day and sent it to the local shops to replace it.
so i managed to boot it into fastboot but sadly i cant do anything due to the bootloader is locked. all i can do is to unbrick it using the qualcomm resets which requires me to made some pin grounding and plug in the usb which allow me to use QFIL.exe to reset the phone into the very stock rom like in the factory.
after the reset it was working as it should but something is not right, the phone cant be used with its touchscreen, wont charge when it sleep and when ever the phone start to get dark when theres no input, it will stop charging and the screen wont turn on again. both when i boot the phone and when i turn off the phone and charge it. im not sure how to troubleshooting as i never encounter in my experiences. also, it will drain my battery. if i plug in my pc it will detect as Qualcomm HS-USB Diagnostics 9006 or Marshall London HS-USB Diagnostics 9006
anyone have solution for this or any idea?
Thanks in advance
AyieStyx said:
Hi, i use the latest CM ROM for K910 for a quite long time. yesterday i dropped my phone and it crack my screen. was sending it for repair and now the phone wont load normally and it stays in CM loading screen and never boot up. With the cracked phone i use it for a day and sent it to the local shops to replace it.
so i managed to boot it into fastboot but sadly i cant do anything due to the bootloader is locked. all i can do is to unbrick it using the qualcomm resets which requires me to made some pin grounding and plug in the usb which allow me to use QFIL.exe to reset the phone into the very stock rom like in the factory.
after the reset it was working as it should but something is not right, the phone cant be used with its touchscreen, wont charge when it sleep and when ever the phone start to get dark when theres no input, it will stop charging and the screen wont turn on again. both when i boot the phone and when i turn off the phone and charge it. im not sure how to troubleshooting as i never encounter in my experiences. also, it will drain my battery. if i plug in my pc it will detect as Qualcomm HS-USB Diagnostics 9006 or Marshall London HS-USB Diagnostics 9006
anyone have solution for this or any idea?
Thanks in advance
Click to expand...
Click to collapse
It shows HS-USB Diagnostics 9006 for you ! So do as I say :
1 . Turn off phone
2. press and hold vol up + vold down
3. connect to usb without powering up
4. You gets what you want !
hello everyone, When i insert my phone to wall charger i blinks the led and a red light flashes to beside the led light, but phones never boots up, cant access recovery and fastboot. Is this a hardware problem? i dont think so because my phone didnt fall i just restarted it and then it didn't boots up.
Any help regarding this will be appreciated.
KhanStan said:
hello everyone, When i insert my phone to wall charger i blinks the led and a red light flashes to beside the led light, but phones never boots up, cant access recovery and fastboot. Is this a hardware problem? i dont think so because my phone didnt fall i just restarted it and then it didn't boots up.
Any help regarding this will be appreciated.
Click to expand...
Click to collapse
No.
Just change your charger don't charge it with moto charger. Use a different good charger and leave your phone phone to charge for more than 6 hours.
Hopefully it will get switched ON.
Ankit_29 said:
No.
Just change your charger don't charge it with moto charger. Use a different good charger and leave your phone phone to charge for more than 6 hours.
Hopefully it will get switched ON.
Click to expand...
Click to collapse
Yes im using different charger, and put it on charging for whole night.. didnt worked :/
KhanStan said:
Yes im using different charger, and put it on charging for whole night.. didnt worked :/
Click to expand...
Click to collapse
Is your bootloader unlocked ?
Ankit_29 said:
Is your bootloader unlocked ?
Click to expand...
Click to collapse
yes.. i was on custom rom
KhanStan said:
yes.. i was on custom rom
Click to expand...
Click to collapse
I think their is something wrong with the ROM.
You have soft bricked your device.
Few months back I too soft bricked my device while on custom rom. But somehow I was able to go in recovery.
Just try to go in recovery mode or if it doesn't work then you have to sideload the rom.
Ankit_29 said:
I think their is something wrong with the ROM.
You have soft bricked your device.
Few months back I too soft bricked my device while on custom rom. But somehow I was able to go in recovery.
Just try to go in recovery mode or if it doesn't work then you have to sideload the rom.
Click to expand...
Click to collapse
recovery and fastboot is not accessible, and how sideload rom?
[edit] this is not soft brick, display dosent show anything.
KhanStan said:
recovery and fastboot is not accessible, and how sideload rom?
[edit] this is not soft brick, display dosent show anything.
Click to expand...
Click to collapse
Your device doesn't even show bootlogo since my device used too.
If it doesn't then you have hard bricked your device.
For sideloading just google it or search in forums but it won't work if you device is hard bricked.