Hi guys,I have a problem romming my HTC Amaze 4g.
I have already unlocked bootloader and installed TWRP recovery but when i flashed official cyanogenmod the phone got bootloop.
No error messages or sg like that.
Dont know what to do please help.
Adam.
tamasicsadam said:
Hi guys,I have a problem romming my HTC Amaze 4g.
I have already unlocked bootloader and installed TWRP recovery but when i flashed official cyanogenmod the phone got bootloop.
No error messages or sg like that.
Dont know what to do please help.
Adam.
Click to expand...
Click to collapse
Off hand the most likely scenario is the kernel didn't get flashed with the rest of the ROM. This is a known issue with TWRP and CWM on devices that are s-on. Try again with ext4 recovery and enable smart flash. It seems to be the recovery with the least amount of problems with this device, especially those that are s-on, and is the solution recommended by most devs here.
Thanks, i will try this and tell you if it is solved.
Sent from my LG-P700 using xda app-developers app
Here again. I have tried what u mentioned .flashed ex4 recovery and tried to flash the rom via that smart thing enabled and when the phone booted up it rebooted when PIN was entered. After that tried to wipe dalvik but it got worse cuz phone got bootloop now. Any ideas?
When flashing by smart flash on you have to flash the kernel seprately
Sent from my HTC_Amaze_4G using Tapatalk
Or the link might have gone bad one another user is also saying the same about cm but there is one more possibility the cm roms are usually quite a lot undervolted i think sports device supports it i had this problem on cm 11 and overvolting did the job but you guys cant even get to the main screen how are you going to overvolt you might just have to edit the kernel which i have no experience of.
Sent from my HTC_Amaze_4G using Tapatalk
Muneeb Saeed said:
When flashing by smart flash on you have to flash the kernel seprately
Sent from my HTC_Amaze_4G using Tapatalk
Click to expand...
Click to collapse
If smart-flash is properly enabled the kernel will flash with the ROM. That's one of the main purposes of smart-flash.
To the OP: obviously you were able to successfully install the ROM this time since you didn't bootloop and were OK until you entered a PIN for the lockscreen. So this issue is different than the first, where you weren't even getting to the lockscreen. The first thing I would try is wiping then reinstalling CM from recovery. This time just try using it without a PIN for an hour and see if you have other issues. Only then set a PIN. If it crashes after setting a PIN, but was working fine before, you know there is a bug in that part of the ROM. If it begins crashing sooner then something else is the problem.
Related
(SOLVED) hello neighbors. I am having an issue... my atrix will only boot if i install honey atrix on it. i have tried many other roms. many different times. i have wiped all data cache partitions, dalvik, battery stats, formatted system, dat, cache. And still i can get nothing to boot besides Honeyatrix rom.
it seems to load them from the zip file ok just wont boot past the unlock dual core screen. i have let it set for 10-20 min to see if it will boot and nothing.
i had recieved this under warranty and it was shipped with the new 2.3.6. 4.5.91 and i rooted and unlocked using the unlock tool v.4.
any help with this would be greatly appreciated
thanks in advance,
SErooted
Try a full wipe with fastboot before flashing. Also may need to flash appropriate kernel. What ROM's have you tried?
Sent from my MB860 using xda premium
ive tried cherry pie, algorythm, cm7, neutrino, miui many of them, and i have never had this problem with my other atrix. just this one doesnt seem to be want todo anything but this one rom. and i have done a full wipe in moto fastboot as well. i forgot to mention it earlier.
SErooted said:
ive tried cherry pie, algorythm, cm7, neutrino, miui many of them, and i have never had this problem with my other atrix. just this one doesnt seem to be want todo anything but this one rom. and i have done a full wipe in moto fastboot as well. i forgot to mention it earlier.
Click to expand...
Click to collapse
Which recovery are you using?
Maybe install it again or try another one, perhaps its not installing properly
Sent from my MB860 using xda premium
i have used cwm and tefnars recovery. i have installed each rom several times and still no change. it will only boot into honey atrix rom. i am really wanting to put miui back on and i have checked the latest by stevend25 ( sorry if spelled wrong) and i can go through the set up process but upon reboot, it wont boot past the startup screen.:-(
Damn replacement device!!!
Seriously people>>>> not one of you has insight on what the problem may be? i am not new to this phone or modding it and this is the first time ive ever had a problem and the community cant help?
PATHETIC!!!
Just wait somebody will answer you, be patience. If u act like this, sure nobody won't help you.
Inviato dal mio Atrix con Tapatalk
SErooted said:
Seriously people>>>> not one of you has insight on what the problem may be? i am not new to this phone or modding it and this is the first time ive ever had a problem and the community cant help?
PATHETIC!!!
Click to expand...
Click to collapse
Since it was almost 2 weeks between the last post trying to help you and your posts yesterday it's pretty safe to say everyone thought you had solved your problem and moved on. After this latest post, it's probably also safe to say you won't receive any more help.
SErooted said:
Seriously people>>>> not one of you has insight on what the problem may be? i am not new to this phone or modding it and this is the first time ive ever had a problem and the community cant help?
PATHETIC!!!
Click to expand...
Click to collapse
You are not entitled to help from anyone. Keep that in mind while making future posts. Always be kind and respectful to other members in the community.
SErooted said:
i have used cwm and tefnars recovery. i have installed each rom several times and still no change. it will only boot into honey atrix rom. i am really wanting to put miui back on and i have checked the latest by stevend25 ( sorry if spelled wrong) and i can go through the set up process but upon reboot, it wont boot past the startup screen.:-(
Damn replacement device!!!
Click to expand...
Click to collapse
your recovery is the problem install rom manager from market and update cwm or try romracer recovery.
Could also be the baseband radio. If that doesn't fix, looks like its time for the dreaded sbf.
Sent from my MB860 using XDA
I would also use the latest romracer recovery or twrp from here http://forum.xda-developers.com/showthread.php?t=1400641. Also be sure to use appropriate kernel for the rom you are flashing and try the stock clocked kernels first. Good luck.
Sent from my MB860 using XDA
hmmmm I wondering on this one if his internal might be mal-partitioned.. I had this problem and was cured using mini tool partition wizard. Start off by making sure all's formatted fat 32 primary. Once you're assured of that, format again, fastboot - w and reinstall something like neutrino. Twice for good measure. Boot it , wait 60 seconds, pull battery and reboot. Lemme know bro if that helped..
Sent from my SGH-I997 using xda premium
How to make atrix's internal partition (system, osh, etc) to be detected by mini tool?
Sent from my MB860 using xda premium
Thank you all for your insight. Im happy that you have responded. Please forgive my frustration. It just has been annoying to keep this software on my attic as there are other Toms I enjoy. Ill let you all know how it goes
Sent from my MB860 using XDA App
i had wondered if this was the problem but i have tried cwm from market and tefnars recovery and had the same issue with both.
Thank you for your ionsight into this. it really has been bothering me.
ok everyone.... thank you all for your help in getting the matter resolved. it was an issue with recovery and i am now running with twrp instead of cwm or tefnar. miui is now running and am going to see what kinda fun i can have with it. Thanks again everyone!!!
Can anyone help?
I'm not a noob, I've been flashing for years but I can't seem to get any Roms I flash to boot after. I just get stuck at the disclaimer boot screen. It stays there, no boot up.
Things I've tried, waiting of course for 10+ mins. Moving the Rom zips to internal sd then flashing. And redownloading the roms and trying again. Roms I've tried are, Meanrom and stock w Sony bravia engine.
Really sucks I can't figure out why I can't boot any new Rom flashes. Any help would be greatly appreciated
Sent from Mars on my Fresh EVO LTE
I'm having this exact issue. Rooted and flashed a couple of ROMs. Backed one up and now I can't boot into any new ROMs, even stock ROMs. They flash fine in recovery but do not pass the HTC disclaimer screen.
Did you by chance select Factory Reset from bootloader with TWRP installed? When I do that it reboots into recovery and cannot mount internal storage. When I try to mount internal storage to my PC through USB it says SD is corrupt and I must format. I have a suspicion that has something to do with not being able to boot new ROMs.
Have you tried to RUU? I've tried just to see if I can get my phone to boot into anything, but I get an error updating signature. Signarure (sic) Error 132.
Something I haven't tried yet would be to flash a ROM and make a nandroid before first boot, then try restoring it to see if it boots. Might be crazy enough to work.
Please post if you manage to solve this annoying soft brick!
Sent from my EVO using XDA
Ladicx said:
Can anyone help?
I'm not a noob, I've been flashing for years but I can't seem to get any Roms I flash to boot after. I just get stuck at the disclaimer boot screen. It stays there, no boot up.
Things I've tried, waiting of course for 10+ mins. Moving the Rom zips to internal sd then flashing. And redownloading the roms and trying again. Roms I've tried are, Meanrom and stock w Sony bravia engine.
Really sucks I can't figure out why I can't boot any new Rom flashes. Any help would be greatly appreciated
Sent from Mars on my Fresh EVO LTE
Click to expand...
Click to collapse
what recovery r u on ...if CWM then ive heard that it doesnt work with the ELTE so that might be ur problem ...if ur on twerp then i cant help u further sorry :crying:
I am having a similar problem. I am unable to flash most roms and ones that I do flash I get stuck on the HTC logo / disclaimer screen. I am also using TWR. Any help would be appreciated. Thank you.
S OFF PEOPLE ARE U ALL UNLOCKED BOOTLOADER WITH S OFF
IF NOT THATS WHY JUST HAVING ROOT WONT WORK
I FLASH JUST FINE WITH TWRP RECOVERY
Sent from my EVO using xda app-developers app
I'm s on and I flash with no issues on twrp did u try moving to to your sd card 2 ?? Sd one don't work
Sent from my EVO using XDA Premium HD app
pbedard said:
I'm s on and I flash with no issues on twrp did u try moving to to your sd card 2 ?? Sd one don't work
Sent from my EVO using XDA Premium HD app
Click to expand...
Click to collapse
±1
We didn't always have s- off and people were flashing fine.. I'm still s- on and running MeanROM myself.
I have non clue what the issue here is, maybe running the ruu and re- rooting?
Sent from my EVO using xda premium
I know that the last part of the twrp rec boot install
Always says fail for me, but I click reboot system and new rom comes alive
I'm not liking the twrp recovery
But for now no choice
Sent from my EVO using xda app-developers app
Hi,
For 2 days my Wifi is giving an error. It says turning on but never does. I have not installed anything or changed a thing. It stopped working for some strange reason. I am on stock mobility with stock kernel, never changed it and I have s-on.
Please help,
Thanks
Try a hard reset
Sent from my HTC_Amaze_4G using xda app-developers app
Is there any way besides a hard reset?
Sent from my HTC Amaze 4G using xda premium
Are you rooted!
Sent from my HTC_Amaze_4G using xda app-developers app
Unlocked bootloader & rooted.
Sent from my HTC Amaze 4G using xda premium
Try clearing Dalvik-Cache in recovery then Fix Permissions. It should help it.
Wipe and reflash stock via hasoon's zip files.
I reset and its still the same. When I try to flash a different kernel it restarts without changing but starts with an error message to contact HTC. I'm fully rooted, unlocked bootloader and s-on and I tried flash.bat and the kernel flasher app but none can change my kernel. Does anyone have any suggestions?
Just noticed bt is not working too
Sent from my HTC Amaze 4G using xda premium
pokey77 said:
I reset and its still the same. When I try to flash a different kernel it restarts without changing but starts with an error message to contact HTC. I'm fully rooted, unlocked bootloader and s-on and I tried flash.bat and the kernel flasher app but none can change my kernel. Does anyone have any suggestions?
Sent from my HTC Amaze 4G using xda premium
Click to expand...
Click to collapse
Well if you are using 4ext recovery (which i highly recommend, best recovery ever made)then there is an option that asks if you are are s-on and you click yes because you are s-on which then allows the recovery to flash any kernel (given its compatible of course) as if you were s-off. That should work, if for some odd reason (for me 4ext never failed even when i was s-on while flashing kernels) it doesnt work then i would suggest attempt to s-off your device via wire trick but be sure to read up thoroughly before you attempt that as some people have bricked their device doing so.
Edit: also i would suggest wipe all partitions except sd card then flash rom and then flash kernel right after to avoid issues.
Could I try to flash a kernel first before flashing. I tried looking for a kernel all day and can't seem to find 1. I used the mobility ota Kernel which does not seem to work.
Sent from my HTC Amaze 4G using xda premium
pokey77 said:
Could I try to flash a kernel first before flashing. I tried looking for a kernel all day and can't seem to find 1. I used the mobility ota Kernel which does not seem to work.
Sent from my HTC Amaze 4G using xda premium
Click to expand...
Click to collapse
Hmm I haven't heard of that kernel before and there aren't many to choose from on this device. First off do you have the ICS ruu? If so just flash faux's kernel with any of theroms that are based off of sense 3.6. Here is the link that is also under the development section of the forums http://faux.androidro.ms/ruby-faux123-kernel-v017.zip for the ICS version ROMs (most of them are) I would suggest speedrom 7.5 as I found it pretty decent for a sense based rom. But you have to flash the ROM first then the kernel but if I recall 4ext recovery with the feature of s-off automatically flashes the kernel that is packaged with the rom it just ends up having to boot twice. So first just flash one of the new sense 3.6 ROMs via 4ext recovery - settings-recovery-check smartflash on and then flash the ROM kernel should automatically flash
Edit: stumbled across this in faux kernel thread might help if 4ext still doesn't work
http://forum.xda-developers.com/showthread.php?t=1359951&page=181
I also had the wifi error problem for some reason when I tried to flash Speedrom 6.5 and 7.0 coming from Supersaiyan 3. Kinda fixed itself after installing Speedrom 7.5/7.6 so maybe try these two steps and it might work for you:
1 ) Of course make a backup
2) When flashing a new or old rom I always Wipe/Factory Reset from 4ext and then just clear dalvik cache, then install whatever rom you like. Never had any probs with this method such as the wifi error you're encountering. Just never got bt error.... weird...
Btw what rom are you currently on?
+1 if this helped anyone!
Sent from my HTC Ruby using xda premium
I'm on mobility stock rom
Sent from my HTC Amaze 4G using xda premium
I switched to speed Rom and bt works but not WiFi.
Sent from my HTC_Amaze_4G using xda premium
I've tried a few roms all day and still no luck.
1. After installing a rom, it always does 1 final step before a restart. It uses a previously saved boot.img which i think is causing my issue but i could be wrong.
1. One thing i noticed is when a rom boots up, the 1st thing it does is turn on WIFI followed by an error.
Has this happened or does any of this makes sense to anyone?
Once again, please help & thanks.
pokey77 said:
I switched to speed Rom and bt works but not WiFi.
Sent from my HTC_Amaze_4G using xda premium
Click to expand...
Click to collapse
Bro its most likely a kernel issue you are facing WiFi issues usually are due to the incorrect kernel flashed or the kernel not flashed at all with the ROM however I would suggest that you flash the stock ruu file (however you will lose both root and recovery but those are easy to reinstall using hasoons tool or various other methods) I say this because this way you will know for sure if you have a hardware or software problem for sure. WiFi should work with stock ruu from your carrier (make sure to download your carrier specific ruu).if you feel you can do s-off via wire trick and then super cid your amaze you will be able to flash any and every ROM for the amaze. I have a suspicion that the ROMs that are out are based off of T-Mobile ruu and people with mobilicity have their amaze super cid to work with any carrier.however did you try flashing cm10 via 4ext maybe since that has an aosp kernel and if flashed with smart flash option in 4ext it may work.
1. After installing a rom, it always does 1 final step before a restart. It uses a previously saved boot.img which i think is causing my issue but i could be wrong.
1. One thing i noticed is when a rom boots up, the 1st thing it does is turn on WIFI followed by an error.
Click to expand...
Click to collapse
Yea it could be the kernel because the thing you said about the 4ext recovery telling you that its loading the saved boot.img is what I always get and whenever i do get it, the rom always works perfectly. Also which version of speedrom did u try because I had the problem when I was using both 6.5 and 7.0. Try flashing the Supersaiyan 3 rom and then choose faux kernel from the AROMA INSTALLER. Then wipe as I told you in the posts before and then flash speedrom. It worked like that for me. Sorry if you still dont have luck!
What would happen if i deleted the boot.img file and flash a kernel?
Sent from my HTC_Amaze_4G using xda premium
pokey77 said:
What would happen if i deleted the boot.img file and flash a kernel?
Sent from my HTC_Amaze_4G using xda premium
Click to expand...
Click to collapse
Well OK I really want this to work for you after you mentioned the boot.IMG issue it may be that you need to flash an insecure boot image first. Here is the link http://forum.xda-developers.com/attachment.php?attachmentid=1223086&d=1343307912 for s-on people this usually needs to be flashed via fastboot and not recovery. However since 4ext recovery seems to be an exception to almost every rule regarding recoveries it may be able to flash it. If not just flash via fastboot I posted the forum topic link that this issue has been discussed on in one of my previous posts in this thread. I'm positive this is your problem now.
---------- Post added at 12:44 AM ---------- Previous post was at 12:36 AM ----------
Read through the issue on this page http://forum.xda-developers.com/showthread.php?t=1359951&page=181 seems like this is exactly the issue you are facing. I suggest after flashing which ever ROM flash fauxs kernel it's the best for the amaze anyway hope you get this to work I have exhausted the last bit of knowledge I have regarding this issue. Hence I s-off my device to avoid stupid issues such as these once and for all.
Should I try s-off before installing the GB ruu?
Sent from my HTC Amaze 4G using xda premium
I have officially stressed myself to the brink. I try to be calm but nowhere do I find how to fix my problem. I have tried flash image gui, I have tried htc dumlock, and I have also tried flashing the .img manually through fastboot usb then flashing the entire zip with twrp 2.2.2.0. Almost every time, I must recover from my TWRP and then use bootimg flasher v1.1 to stop my evo from getting stuck at the boot screen.
Everytime I attempt, I wipe the system and cache, then flash the boot.img, then flash the zip, then the gapps and reboot and it gets stuck on the splashscreen. I must note also that when I had first rooted, and installed Rom toolbox pro, I picked out a boot animation and installed it, restarted the phone, and it didnt work. BUT NOW sometimes after i flash the CM10 that random boot animation appears. WTF? even after i wipe the memory and everything. So I turned off the boot animation, and even deleted them from the phone off the app and it still comes up. I believe this is part or maybe IS the problem. But either way, I do not know how to deal with it. I have had the Cyanogenmod 10 boot animation ONCE out of the many times I have tried flashing but it was stuck on that screen forever like I have read other users have had happen. I REALLY, REALLY would like to be able to use the rom, as it has the new google now voice and all the cool features that i would like to have now that I am rooted.
NOTES:
I am running my stock rom. I have not installed any other ROMS on my phone. The backup i created was after I installed the stupid boot animation. (In case thats another problem)
When i tested the "current" boot animation from within rom toolbox pro, the normal htc evo 4g lte Sprint one loaded but yet, the retarded one i chose for ****s and giggles is what keeps loading. FML (I shouldve chose at least a cool one.)
My backup works fine. I am damn glad i made it!!!
Sorry for any grammatical errors, lowercase i's and what not. im too lazy to press the shift key sometimes. (Caps lock is broken. FML.)
Also sorry for it being so long. I am trying to be thorough to give you experts what you need to help me out.
If you need anymore info as far as detail instructions i will be happy to write back on this forum.
PLEASE do not tell me that my answer is on another forum, because I believe that it is not due to the special situation I have. I have tried looking for days for an answer.
I will be periodically checking this forum for any replies and will reply ASAP, whenever i am available.
Thank you for your time and patience!
Here is my phone's specs. I tried to get as much as possible. Again, if there is more info that would be needed I will gladly get it and post it here.
I am running on booloader:
Tampered
Unlocked
Jewel PVT SHIP S-ON RL
HBOOT- 1.19.0000
Radio- 1.12.11.0009
OpenDSP-v29.1.0.45.0622
eMMc-boot
Aug 9, 2012, 15:14:25
About Phone:
Hardware Version 0003
Android Version 4.0.4
Sorftware 2.13.651.1 710RD
HTC Sense Version 4.1
HTC SDK API level 4.24
HTCExtension_403_1_GA_22
PRI Version 2.45_003
PRL Version 25006
Anyone?
Sent from my EVO using xda app-developers app
What happens when u fastboot the kernel? Does it say success?
Sent from my EVO using xda premium
Use fastboot to flash the kernel, if you still have trouble wipe the partion and try again
Fastboot flash boot boot.img extract it from the Rom and place in adb folder.
Fastboot erase boot to wipe partition
I had problems trying out CM10 also. This worked for me.
Edit:: I'm assuming you have TWRP recovery and are unlocked before you start this...
Buy Flash GUI from app store. Worth the 99 cents!
Open it and point it to the CM10 zip. It will extract the parts it needs and flash the kernel.
Once that is done have it reboot (it prompts you) into recovery and then wipe system, do factory reset, then flash the CM10 zip and gapps zip.
Reboot one last time
The CM10 animation went on for a couple/few minutes the first time, don't panic.
You should be good after that.
Make sure to install Flash GUI again though. You will need to use it to go back to a ICS/Sense ROM later (using same method). And my guess is you might want to.
CM10 is incredible on this phone but it's not quite ready. I have tons of data connection issues and NEVER get 4G in the places where I've always had good signal. Also, the camera is just about worthless. No disrespect to the devs working on it. I'd have no idea how to work the magic they are doing and I appreciate their time.
Good luck.
I did the very same thing earlier today. I flashed CM10 without paying attention tot he fact that I was unlocked but still had S-On so the phone would continually get stuck on the boot screen. I must have reflashed and formatted with TWRP 10 times before diving into it deeper.
In terms of workflow the only way I could make it work properly was to:
1. Use TWRP to flash CM10 and gapps (just add both zips)
2. Reboot into bootmanager using TWRP.
3. Use fastboot to flash boot.imgfrom the CM10 zip (fastboot flash boot /path/to/boot.img)
If I did the boot.img first it didn't seem to work, it should so maybe that wasn't the real issue but the above process worked and I'm now running CM10.
When I fast boot the kernel everything says success with no errors
Sent from my EVO using xda app-developers app
How do you partition? Do you think that is my problem?
Sent from my EVO using xda app-developers app
You don't need to partition anything, just flash kernel and reboot
Hey guys thanks to everyone replying! I'm currently at work as a delivery driver trying to write back.... Dangerous! Lol but also I have the 5 min limit to post so I will try and do some of these methods when I get home and report my findings to you all ASAP! But to anyone with more suggestions please keep bringing Em!
Thanks!
Sent from my EVO using xda app-developers app
Hey guys its me again. I just got home and I'm dead beat tired. I had to work later than I thought. Im gonna get some sleep but once again thank you everyone for giving me some answers that I can try tomorrow! I will, without a doubt, try some of them tomorrow after my classes. But first I would like to leave you all with a VERY important question that I did not think of. Is there a stable release of cm10 that has worked for you all that I can try? Perhaps that was the problem too? I was trying the nightly release that came out October 2. Once again thank you all for replying and i will try to do this ASAP after class. Sorry to leave you guys hanging so much!
Sent from my EVO using xda app-developers app
Thing is it's a nightly, some people have flashed back to earlier versions and others upgrade with out any issues. Ymmv
padrino121 said:
I did the very same thing earlier today. I flashed CM10 without paying attention tot he fact that I was unlocked but still had S-On so the phone would continually get stuck on the boot screen. I must have reflashed and formatted with TWRP 10 times before diving into it deeper.
In terms of workflow the only way I could make it work properly was to:
1. Use TWRP to flash CM10 and gapps (just add both zips)
2. Reboot into bootmanager using TWRP.
3. Use fastboot to flash boot.imgfrom the CM10 zip (fastboot flash boot /path/to/boot.img)
If I did the boot.img first it didn't seem to work, it should so maybe that wasn't the real issue but the above process worked and I'm now running CM10.
Click to expand...
Click to collapse
Which nightly did you use?
Hey guys so I used padrino121s suggestion for flashing. At first I tried flash gui again like you had suggested but it got stuck in the boot screen. So I decided to download a different nightly release (20121002) and it flashed perfectly and everything transferred over correctly! Thank you guys so much for all of your help! Now one more question... If I decide to get a new nightly build, do I have to flash everything all over again like I had to the first time? Or because I have flashed cyanogen mod already do I just do something else to update it?
Sent from my EVO using xda app-developers app
I recently rooted my HTC sensation and i have now achieved S-off and unlocked my phone.
The main problem is that now if my phone turns off to reboot it I need to go into the recovery and to the command Fastboot boot boot.img. i really need a solution to this because its really annoying to have to use my computer every time I need to reboot my phone especially because im using a CWM and i have a nightly CM rom currently installed
HELP PLEASE
Sounds like something is wrong with the kernel, try to do a full wipe and flash the ROM again
Sent from my Nexus 4 using xda premium
thankswill try that im going on holiday so i will do it when i get back hopefully my phone won't die
ive tried that now and its still not working, i also tried flashing a custom ROM and its still not working.
Maybe try to reflash your bootloader?
Sent from my Nexus 4 using xda premium
I've tried flashing the bootloader and the problems still occurring.
any other ideas?
I don't own a sensation so I don't know this is a common issue, but you can always try reverting to stock and restoring radio secure flags, this can tell you if its firmware/software or a hardware fault
Sent from my Nexus 4 using Tapatalk 2
is their possibly a link you could provide to help me with restoring radio secure flags or is that restored when reverting back to stock.
plz and thank you
anything?
asianminime said:
anything?
Click to expand...
Click to collapse
Hi,
Try running a RUU.
Look HERE
Are you supercid?
hello I fixed the problem I didn't use the RUU however because I was really confused doing it.
the way In which I had done it was by factory resetting my phone and completely wiping the data and the cache so I didn't have any rom installed it was just the phone and the bootloader. then I went and re-installed the ROM I had chosen with the CWM recovery. although after I had installed the rom and the G-apps I wen and I opened a command prompt window and used the following instruction:
Fastboot Flash boot boot.img
after this I had rebooted my phone using the code:
Fastboot boot boot.img because I didn't know I had fixed the problem but I had to reset my phone and It just worked so thank you all so much for your help I really appreciate all the help and support given :good::victory: