I have rooted Mega 6.3 i9205 with stock rom (XXHUAMH2) and the CWM recovery that i downloaded here http://forum.xda-developers.com/showthread.php?t=2369998 doesn't work after flashing it with odin and it goes back to the original stock recovery. I tried a lot of ways but to no avail.
Is there anyone here to successfully boot into CWM recovery mode? Thanks. Please help
Did you try this one?
Phil3759 CWM >> http://forum.xda-developers.com/showthread.php?t=2588661
DarkRoyale said:
- cut - after flashing it with odin and it goes back to the original stock recovery. I tried a lot of ways but to no avail.
Is there anyone here to successfully boot into CWM recovery mode? Thanks. Please help
Click to expand...
Click to collapse
There is one trick you have to do:
After flashing CWM you HAVE TO go to recovery immediately, before booting into ROM. After that you can reboot from CWM and it will be permanent.
If you reboot to system instead, there stock recovery will be automatically reflashed.
I have flashed CWM successfully using this method.
Thank for the replies. Now I got it
I I rooted my S2 I777 using Frameroot-1.4.2 and flashed via Odin CWM 5.0.2.3 then I flashed AoCP KitKat from from GalaxyS2Root.com and now my phone is in a loop entering in recovery mode.
I flashed the rom on CWM and when I asked to reboot the system it start reboot and enter in recovery mode again.
I tried to flash the official rom from AT&T with Android 2.3.4 and even after I flash this rom it doesn't stop to enter in recovery mode.
First thing to do: perform a wipe/data from within recovery.
creepyncrawly said:
First thing to do: perform a wipe/data from within recovery.
Click to expand...
Click to collapse
It was done and still reboot in recovery.
I tried to install a stock rom via Odin 1,85 but I failed in all the tries then I tried via Odin 3.07 and it worked and I did a full wipe and rebooted the system and it got back to recovery mode then I did it again and it worked.
Now I'm using a stock Rom with Androind 4.2.1.
Before it works I've tried to install the stock Rom and it worked then I rooted the phone and installed CWM and it always reboot in recovery mode.
gsilva92 said:
...then I rooted the phone and installed CWM and it always reboot in recovery mode.
Click to expand...
Click to collapse
This part makes me think you use Rom Manager, and that would explain why it keeps rebooting. There's no need to install CWM separately as it's included in i777 kernels. Rom Manager will ruin your phone, stay away from it (see the sticky).
SteveMurphy said:
This part makes me think you use Rom Manager, and that would explain why it keeps rebooting. There's no need to install CWM separately as it's included in i777 kernels. Rom Manager will ruin your phone, stay away from it (see the sticky).
Click to expand...
Click to collapse
I don't use Rom Manager.
It was rooted before and I was using a KitKat Rom but I tried to flash the Rom I mentioned and it bricked.
I unbricked it and rooted and installed CWM then it started with the problem.
As I said now I'm using a stock Rom with Android 4.2.1.
You said CWM is included in i777 Kernels so if I root my phone I can simply get in recovery mode and use the stock recovery to flash the Rom?
You mentioned that you rooted the stock firmware and installed a custom recovery, but without knowing your root - recovery process, it's hard to say where things went sideways.
The kernel of the i777 does include the recovery, but the stock kernel cannot be used to flash custom firmware.
>>this guide<< is one of the more reliable ways to go from stock to custom firmware.
summary;
-framaroot to establish root
-mobile odin to install custom kernel
-custom kernel to install custom firmware
happy flashing
-Cyril
gsilva92 said:
I don't use Rom Manager.
It was rooted before and I was using a KitKat Rom but I tried to flash the Rom I mentioned and it bricked.
I unbricked it and rooted and installed CWM then it started with the problem.
As I said now I'm using a stock Rom with Android 4.2.1.
You said CWM is included in i777 Kernels so if I root my phone I can simply get in recovery mode and use the stock recovery to flash the Rom?
Click to expand...
Click to collapse
cyril279 said:
You mentioned that you rooted the stock firmware and installed a custom recovery, but without knowing your root - recovery process, it's hard to say where things went sideways.
The kernel of the i777 does include the recovery, but the stock kernel cannot be used to flash custom firmware.
>>this guide<< is one of the more reliable ways to go from stock to custom firmware.
summary;
-framaroot to establish root
-mobile odin to install custom kernel
-custom kernel to install custom firmware
happy flashing
-Cyril
Click to expand...
Click to collapse
Thank you.
I'll follow this guide and I'll post here if it worked for me.
cyril279 said:
You mentioned that you rooted the stock firmware and installed a custom recovery, but without knowing your root - recovery process, it's hard to say where things went sideways.
The kernel of the i777 does include the recovery, but the stock kernel cannot be used to flash custom firmware.
>>this guide<< is one of the more reliable ways to go from stock to custom firmware.
summary;
-framaroot to establish root
-mobile odin to install custom kernel
-custom kernel to install custom firmware
happy flashing
-Cyril
Click to expand...
Click to collapse
I tried to follow the instruction in the link you sent me but I failed doing it.
I searched on google and I saw that Odin has an option OTA / Update zip but mine doesn't have this option.
Is there something I should do before flash a custom rom?
I'm using Mobile Odin Pro.
gsilva92 said:
I tried to follow the instruction in the link you sent me but I failed doing it.
I searched on google and I saw that Odin has an option OTA / Update zip but mine doesn't have this option.
Is there something I should do before flash a custom rom?
I'm using Mobile Odin Pro.
Click to expand...
Click to collapse
Agreed, the instructions in that guide can be a little confusing.
First, are you sure you are using the AT&T Galaxy S II SGH-I777? Because you said several times in this thread that you are now running 4.2.1, but there is no such version of the os for this phone. The latest official AT&T stock firmware is I777UCMD8 which is 4.1.2.
If you affirm that your phone is SGH-I777 running UCMD8 firmware, and that you have root, then the next step is to use mobile odin to flash AJK v4.9 NoSwap kernel. Download the zip file from the Kernel thread. Open the zip file with an archiving tool such as win-zip, 7zip, etc. and extract the boot.img. Mobile odin will not recognize the zip file, but it will recognize the boot.img as a kernel, and will flash that. So transfer the boot image to the phone sd card and flash with mobile odin.
Next, you will find that the phone buttons don't work. Transfer the AJK v4.9 zip file to the sd card, enter into Clockwork Mod recovery and flash the AJK v4.9 zip file. This will fix the buttons. Now you have a working stock UCMD8 with custom AJK kernel. Now you are ready to flash what ever firmware you want. Hope this helps, and feel free to ask questions.
creepyncrawly said:
Agreed, the instructions in that guide can be a little confusing.
First, are you sure you are using the AT&T Galaxy S II SGH-I777? Because you said several times in this thread that you are now running 4.2.1, but there is no such version of the os for this phone. The latest official AT&T stock firmware is I777UCMD8 which is 4.1.2.
If you affirm that your phone is SGH-I777 running UCMD8 firmware, and that you have root, then the next step is to use mobile odin to flash AJK v4.9 NoSwap kernel. Download the zip file from the Kernel thread. Open the zip file with an archiving tool such as win-zip, 7zip, etc. and extract the boot.img. Mobile odin will not recognize the zip file, but it will recognize the boot.img as a kernel, and will flash that. So transfer the boot image to the phone sd card and flash with mobile odin.
Next, you will find that the phone buttons don't work. Transfer the AJK v4.9 zip file to the sd card, enter into Clockwork Mod recovery and flash the AJK v4.9 zip file. This will fix the buttons. Now you have a working stock UCMD8 with custom AJK kernel. Now you are ready to flash what ever firmware you want. Hope this helps, and feel free to ask questions.
Click to expand...
Click to collapse
Thank you.
I'm gonna try it and I'll post at night (in Brazil) when I come back from work.
creepyncrawly said:
Agreed, the instructions in that guide can be a little confusing.
First, are you sure you are using the AT&T Galaxy S II SGH-I777? Because you said several times in this thread that you are now running 4.2.1, but there is no such version of the os for this phone. The latest official AT&T stock firmware is I777UCMD8 which is 4.1.2.
If you affirm that your phone is SGH-I777 running UCMD8 firmware, and that you have root, then the next step is to use mobile odin to flash AJK v4.9 NoSwap kernel. Download the zip file from the Kernel thread. Open the zip file with an archiving tool such as win-zip, 7zip, etc. and extract the boot.img. Mobile odin will not recognize the zip file, but it will recognize the boot.img as a kernel, and will flash that. So transfer the boot image to the phone sd card and flash with mobile odin.
Next, you will find that the phone buttons don't work. Transfer the AJK v4.9 zip file to the sd card, enter into Clockwork Mod recovery and flash the AJK v4.9 zip file. This will fix the buttons. Now you have a working stock UCMD8 with custom AJK kernel. Now you are ready to flash what ever firmware you want. Hope this helps, and feel free to ask questions.
Click to expand...
Click to collapse
I did exactly what you said and it worked but when I tried to flash a custom Rom it failed and bricked my phone again.
And now I'm back to the first topic, it always reboots in the recovery mode.
I'll try to fix it again.
I didn't see the error it showed me when failed in flash the custom rom. I know I should have seen it.
Here is a video of my phone rebooting in the recovery mode.
gsilva92 said:
I did exactly what you said and it worked but when I tried to flash a custom Rom it failed and bricked my phone again.
And now I'm back to the first topic, it always reboots in the recovery mode.
I'll try to fix it again.
I didn't see the error it showed me when failed in flash the custom rom. I know I should have seen it.
Here is a video of my phone rebooting in the recovery mode.
Click to expand...
Click to collapse
What firmware did you try to flash? If you tried again to flash the "AoCP KitKat from GalaxyS2Root dot com" that you mentioned in your first post, that in itself could be the problem. In the past, many products from the GalaxyS2Root website have caused numerous and various types of problems, including similar to your issue. For most of the past two and a half years, we have been advising people to avoid the Galaxy S2 Root website and products. It is best to flash firmware downloaded from XDA-Developers.
If you are trying to install a version of kitkat on your phone, then you also probably need advice from someone more familiar with kitkat, like cyril279 or SteveMurphy. Maybe one of them will jump in and help.
gsilva92 said:
I I rooted my S2 I777 using Frameroot-1.4.2 and flashed via Odin CWM 5.0.2.3 then I flashed AoCP KitKat from from GalaxyS2Root.com and now my phone is in a loop entering in recovery mode.
I flashed the rom on CWM and when I asked to reboot the system it start reboot and enter in recovery mode again.
I tried to flash the official rom from AT&T with Android 2.3.4 and even after I flash this rom it doesn't stop to enter in recovery mode.
Click to expand...
Click to collapse
Just breezed through this and didn't see this mentioned but in the aocp kitkat forum here it states in the op you must be on cwm 6.0.4.4 or higher to flash their ROM. This is true for all kitkat ROMs I've tried so far. This may have been the source of your problem although usually most report getting a status7 error at this point but I'm not familiar with that cwm version you mentioned.
Also twrp works really well and it's touch based.
creepyncrawly said:
What firmware did you try to flash? If you tried again to flash the "AoCP KitKat from GalaxyS2Root dot com" that you mentioned in your first post, that in itself could be the problem. In the past, many products from the GalaxyS2Root website have caused numerous and various types of problems, including similar to your issue. For most of the past two and a half years, we have been advising people to avoid the Galaxy S2 Root website and products. It is best to flash firmware downloaded from XDA-Developers.
If you are trying to install a version of kitkat on your phone, then you also probably need advice from someone more familiar with kitkat, like cyril279 or SteveMurphy. Maybe one of them will jump in and help.
Click to expand...
Click to collapse
I'm trying to flash a Rom form XDA-Developers http://forum.xda-developers.com/showthread.php?t=2544790
I'll try to contact one of the users you mentioned. Thank you.
razen_kain said:
Just breezed through this and didn't see this mentioned but in the aocp kitkat forum here it states in the op you must be on cwm 6.0.4.4 or higher to flash their ROM. This is true for all kitkat ROMs I've tried so far. This may have been the source of your problem although usually most report getting a status7 error at this point but I'm not familiar with that cwm version you mentioned.
Also twrp works really well and it's touch based.
Click to expand...
Click to collapse
I'll try to flash twrp to flash KitKat. Thank you.
Good catch @razen_kain, the details were in the OP all along.
That said, The details of what you need to flash the firmware are in the OP of each Firmware thread, including the necessary kernel version, and where to find it.
Omni
Cyril279 said:
[...]
Recovery requirement (prior to flashing this firmware):
================
CWM 6.0.4.4+
--OR--
TWRP 2.6.3.0+
-Renderbroken's OmniROM kernel
-or- Flash Omni's Boot.IMG via MobileOdin
--------------------------------
SGH-S959G; (courtesy of @mr-cook)
TWRP 2.6.3.0.zip
--OR--
CWM 6.0.4.5.zip.[...]
Click to expand...
Click to collapse
CM 11
RenderBroken said:
[...]HOW TO INSTALL
Make sure you are on CWM 6.0.4.4+ before flashing ROM! Thanks to @mr-cook you can now download and flash just the recovery/kernel!
Other handy scripts you can use from mr-cook can be found: Here
Download 6.0.4.5 Recovery/Kernel created by mr-cook : Here[...]
Click to expand...
Click to collapse
AOCP 7.0
crt60 said:
HOW TO INSTALL
***(If you are on Jellybean or older, you will need the latest CWM recovery for the i777 to flash this ROM)***
***If you are having trouble with flashing the zip, you can try the odin version from here***
Click to expand...
Click to collapse
------------------------------------------------------------------------------------------------------
gsilva92 said:
I I rooted my S2 I777 using Frameroot-1.4.2 and flashed via Odin CWM 5.0.2.3 then I flashed AoCP KitKat from from GalaxyS2Root.com and now my phone is in a loop entering in recovery mode.
I flashed the rom on CWM and when I asked to reboot the system it start reboot and enter in recovery mode again.
I tried to flash the official rom from AT&T with Android 2.3.4 and even after I flash this rom it doesn't stop to enter in recovery mode.
Click to expand...
Click to collapse
gsilva92 said:
I'm trying to flash a Rom form XDA-Developers http://forum.xda-developers.com/showthread.php?t=2544790
I'll try to contact one of the users you mentioned. Thank you.
I'll try to flash twrp to flash KitKat. Thank you.
Click to expand...
Click to collapse
If you go back to AT&T stock 4.1.2 I777UCMD8 to start over, here are a couple of ways to get the kernel you need. Please bear in mind that the only kernel that will boot UCMD8 into system is the AJK v4.9 kernel that you used before. When you install another kernel such as RenderBroken's CWM or TWRP kenrel, or the one from OmniRom, the system will no longer boot, but you will be able to boot into recovery, so just avoid trying to boot the system, and choose the option to boot directly into recovery. Or... pull the battery and then use the button combo to enter recovery.
1) Extract the boot.img directly from the OmniRom zip file, and flash that using mobile odin. In this case, once you have UCMD8 rooted, you can skip the step of flashing AJK and flash the OmniRom kernel directly. Reboot into the new recovery and flash OmniRom.
2) Flash the AJK kernel as in my previous instructions. Then enter recovery and flash RenderBroken's kernel. Boot directly into recovery and flash OmniRom.
cyril279 said:
Good catch @razen_kain, the details were in the OP all along.
That said, The details of what you need to flash the firmware are in the OP of each Firmware thread, including the necessary kernel version, and where to find it.
Omni
CM 11
AOCP 7.0
------------------------------------------------------------------------------------------------------
Click to expand...
Click to collapse
I gotta say I didn't read the full info after flash the rom.
creepyncrawly said:
If you go back to AT&T stock 4.1.2 I777UCMD8 to start over, here are a couple of ways to get the kernel you need. Please bear in mind that the only kernel that will boot UCMD8 into system is the AJK v4.9 kernel that you used before. When you install another kernel such as RenderBroken's CWM or TWRP kenrel, or the one from OmniRom, the system will no longer boot, but you will be able to boot into recovery, so just avoid trying to boot the system, and choose the option to boot directly into recovery. Or... pull the battery and then use the button combo to enter recovery.
1) Extract the boot.img directly from the OmniRom zip file, and flash that using mobile odin. In this case, once you have UCMD8 rooted, you can skip the step of flashing AJK and flash the OmniRom kernel directly. Reboot into the new recovery and flash OmniRom.
2) Flash the AJK kernel as in my previous instructions. Then enter recovery and flash RenderBroken's kernel. Boot directly into recovery and flash OmniRom.
Click to expand...
Click to collapse
I did exactly what you said and it worked. Now I'm running OmniRom and I didn't have any problem during the process to flash and not even after.
Thank you everyone.
I'll be more careful next time.
gsilva92 said:
I gotta say I didn't read the full info after flash the rom.
I did exactly what you said and it worked. Now I'm running OmniRom and I didn't have any problem during the process to flash and not even after.
Thank you everyone.
I'll be more careful next time.
Click to expand...
Click to collapse
Welcome to the club :thumbup:
razen_kain said:
Welcome to the club :thumbup:
Click to expand...
Click to collapse
Thank you.
My Quattro was previously running on cosmic Rom with philz recovery img but now I switched back to stock Rom but the bootloader is still show the build number different in the bootloader because of which software update download but doesn't install. Pls help me
Aditya78 said:
My Quattro was previously running on cosmic Rom with philz recovery img but now I switched back to stock Rom but the bootloader is still show the build number different in the bootloader because of which software update download but doesn't install. Pls help me
Click to expand...
Click to collapse
did you use odin for flashing stock? flash stock firmware
Yes I did switched to stock Rom through Odin and the phone is working but software update downloads but when the time comes for installation it goes into bootmode and says installation aborted. Could you pls tell me that if I am using a custom Rom that is installed by philz recovery "install zip from ext card " then how to switch back to stock Rom using Odin.
Aditya78 said:
Yes I did switched to stock Rom through Odin and the phone is working but software update downloads but when the time comes for installation it goes into bootmode and says installation aborted. Could you pls tell me that if I am using a custom Rom that is installed by philz recovery "install zip from ext card " then how to switch back to stock Rom using Odin.
Click to expand...
Click to collapse
Update via kies looks like update.zip was corrupted
Hi i was trying to flash cwm but now when i boot my phone all i see is samsung galaxy note 3 and on the top left it says :
Recovery booting...
recovery is not seandroid enforcing
set warranty bit:recovery
It just keeps rebooting i took out the battery and it still does this! I cant get into download mode or anything please help.
I used the odin root file (like a re-root) to fix this when it happened to me
Yep me too
More details like android version...the recovery filename would help. As others have stated, try flashing the cf-autoroot file for the SM-N900P
My guess is that your recovery isnt there. This happened to me once and I fixed it by reflashing TWRP thru Odin
Sent from my SM-N900P using Tapatalk
jpeery88 said:
I used the odin root file (like a re-root) to fix this when it happened to me
Click to expand...
Click to collapse
Where exactly did you find the odin root file? My phone works perfectly but I can't get into recovery mode to flash any other ROM. Thanks in advance.
mdj8606 said:
Where exactly did you find the odin root file? My phone works perfectly but I can't get into recovery mode to flash any other ROM. Thanks in advance.
Click to expand...
Click to collapse
No such thing as a odin root file, jpeery88 is correct just didn't say it quite right. First odin is software used to install (flash) rom and recovery (files) into your device (phone). ROMS are stock or custom and rooted. You need to get into download mode to install a custom recovery first before you can flash a custom rom. Click on ROM flashing basics in my signature for more info on how to get into download and recovery modes, root your device and more . . .
jimzweb1 said:
No such thing as a odin root file, jpeery88 is correct just didn't say it quite right. First odin is software used to install (flash) rom and recovery (files) into your device (phone). ROMS are stock or custom and rooted. You need to get into download mode to install a custom recovery first before you can flash a custom rom. Click on ROM flashing basics in my signature for more info on how to get into download and recovery modes, root your device and more . . .
Click to expand...
Click to collapse
I have a similar problem. N900p with android 5.0 wont go into recovery or download modes. It displays the message and restarts, repeating the process
nanatheo said:
I have a similar problem. N900p with android 5.0 wont go into recovery or download modes. It displays the message and restarts, repeating the process
Click to expand...
Click to collapse
This was normally a job for a USB jig. I've not found anything for a note 3 though. You might take the battery out over night and try again.
Maybe with the sd card out as well.
Finally I think I've read an attempt with battery out but plugged into power.
after that its punt and buy a "new to you" one on ebay; they're like $140 now a days.
Hi guys,
my friend accidentally bricked his phone while he was trying to install a new ROM.
It is a Galaxy S4 and he accidentally deleted everything, whice means there is no system and no recovery.
What can I do?
Appreciate any help.
Thanks in advance!
Go Into Download Mode (vol+ and power button i think) and Flash new Rom with Odin
Sent Form A1001 One Plus One Using Tapatalk on CM14 <3
KrYptoNxXx said:
Go Into Download Mode (vol+ and power button i think) and Flash new Rom with Odin
Sent Form A1001 One Plus One Using Tapatalk on CM14 <3
Click to expand...
Click to collapse
I tried it but i am getting an error in Odin.. doesn't Odin need a recovery like TWRP or something to install a ROM?
Adi_vizgan said:
I tried it but i am getting an error in Odin.. doesn't Odin need a recovery like TWRP or something to install a ROM?
Click to expand...
Click to collapse
Odin can work independently in download mode
were you able to go into download mode?
rajat224 said:
Odin can work independently in download mode
were you able to go into download mode?
Click to expand...
Click to collapse
How can I install a ROM from Odin? the ROM is a zip file and Odin doesn't let me choose zip files.
Adi_vizgan said:
How can I install a ROM from Odin? the ROM is a zip file and Odin doesn't let me choose zip files.
Click to expand...
Click to collapse
Odin is for flashing the original firmware from Samsung. You should be able to find it here in the forum for your phone. They usually will post it either in the General or Development sub-forums. If you can't find the exact one you need, then you can check out sammobile.com, though it is usually a pretty slow download. You must use the one for your variant of S4 and can be specific to your carrier or region, depending on which S4 you have. You should only use the same firmware or newer.
odin for samsung
i will recommend try flashing a custom recovery like twrp or philz for flashing a custom rom
flash recovery image using odin or any adb boot type commands
also be device specific when u search for rooting or flashing roms to avoid bricking of the device