Ok Here is what I have and have done: :crying: :crying:
All I did was turn it off then screwing around I held the power button and vol+ and hit screen rotate lock switch as it was booting, then it read:
erasing userdata
unrecoverable bootloader error
And thats it. unfortunately adb is not turned on and now the tab will not boot past the secondary booting screen that reads Iconiatab, what is worse since I still have the stock recovery I cant flash anything that I have found. I have tried to flash the Stock A200 rom that is supposed to be stock recovery flashable but it only gets about 1/4th of the progress line before the dead android with the triangle !! sign appears. and of course I dont have the cpuid or sbk, so I cant flash anything in APX mode either.... I am really pulling my hair out here.. and really need some help here it is my nephews tab and he is going to be really upset if I cant fix it.
Any way this is the name of the rom that wont finish installing in the stock recovery flash :
(Stock Rom)Acer_A200_AV032.RV09RC08_AV041.RV04RC02_PA_CUS1_1330081316944_80bf3f7e_decrypted.zip
( I am not allowed to post links yet... But any way the download is at 4shared, and I got the link from the Acer Tablet Forums)
It is Titled Original Stock Rom, and it should have been able to have been flashed through the stock recovery, but di not, and I dont know if it is the rom, or the tablet that is the cause of it not flashing through the stock recovery....
And I have tried a few other update.zips to no avail, but that was the only full rom I found, and certainly the only one with the bootloader blob in it.
Does anyone have any kind of advice for me, or do you know where I could get a rom that will flash through stock recovery?
I dont understand why this happened, the tab was working just fine then I had to reboot it while screwing with the buttons...
So if anyone can help me I would be most grateful, and I can follow most any guide or instruction as long as it can be located.
Thank You
PS - The Tab is 100% stock, no root, no custom recovery, nothing....
A200 unrecverable bootloader error Solved
Iconialististic said:
Ok Here is what I have and have done: :crying: :crying:
All I did was turn it off then screwing around I held the power button and vol+ and hit screen rotate lock switch as it was booting, then it read:
erasing userdata
unrecoverable bootloader error
And thats it. unfortunately adb is not turned on and now the tab will not boot past the secondary booting screen that reads Iconiatab, what is worse since I still have the stock recovery I cant flash anything that I have found. I have tried to flash the Stock A200 rom that is supposed to be stock recovery flashable but it only gets about 1/4th of the progress line before the dead android with the triangle !! sign appears. and of course I dont have the cpuid or sbk, so I cant flash anything in APX mode either.... I am really pulling my hair out here.. and really need some help here it is my nephews tab and he is going to be really upset if I cant fix it.
Any way this is the name of the rom that wont finish installing in the stock recovery flash :
(Stock Rom)Acer_A200_AV032.RV09RC08_AV041.RV04RC02_PA_CUS1_1330081316944_80bf3f7e_decrypted.zip
( I am not allowed to post links yet... But any way the download is at 4shared, and I got the link from the Acer Tablet Forums)
It is Titled Original Stock Rom, and it should have been able to have been flashed through the stock recovery, but di not, and I dont know if it is the rom, or the tablet that is the cause of it not flashing through the stock recovery....
And I have tried a few other update.zips to no avail, but that was the only full rom I found, and certainly the only one with the bootloader blob in it.
Does anyone have any kind of advice for me, or do you know where I could get a rom that will flash through stock recovery?
I dont understand why this happened, the tab was working just fine then I had to reboot it while screwing with the buttons...
So if anyone can help me I would be most grateful, and I can follow most any guide or instruction as long as it can be located.
Thank You
PS - The Tab is 100% stock, no root, no custom recovery, nothing....
Click to expand...
Click to collapse
The problem was solved by following a YouTube video covering this issue, the video was in spanish, but was rather easy to understand even with the language barrier.
Simply keep doing same boot method over, and over until it works! 12 tries for me then a succesfull boot!
Press the power button and vol+ until the tab vibrates, then flip the screen rotation lock switch.
The screen will read erasing userdata, then the red unrecoverable bootloader error (0x190000008), hold down the power until the tab shuts down.
Continually repeat the proccess, and eventually it will read erasing userdata, and follow with formating cache, then complete. The device will reboot, and it is back tonormal now the stock recovery will finish flashing the ota update.zip so long as you have the right stock rom.
Now you can continue on with your tab however you decide, root, install a custom recovery, and rom, and of course unlocking the bootloader in fastboot mode with oem-unlock
Thank you.
the person who posted before this was correct on pressing the vol up key and power then when vibrates release power but holding vol up switch the screen rotation switch from the right to the left and stay holding the vol up key until it show the android screen leave it be and it will be done once finished loading. You don't have to keep repeating the process one time will work if done correctly. the vol up button is the button to the right when holding in landscape view and the rotation switch should also be in the right most position to start. anyway other than those details it works and it will work the first time. Good luck!
Iconialististic said:
The problem was solved by following a YouTube video covering this issue, the video was in spanish, but was rather easy to understand even with the language barrier.
Simply keep doing same boot method over, and over until it works! 12 tries for me then a succesfull boot!
Press the power button and vol+ until the tab vibrates, then flip the screen rotation lock switch.
The screen will read erasing userdata, then the red unrecoverable bootloader error (0x190000008), hold down the power until the tab shuts down.
Continually repeat the proccess, and eventually it will read erasing userdata, and follow with formating cache, then complete. The device will reboot, and it is back tonormal now the stock recovery will finish flashing the ota update.zip so long as you have the right stock rom.
Now you can continue on with your tab however you decide, root, install a custom recovery, and rom, and of course unlocking the bootloader in fastboot mode with oem-unlock
Thank you.
Click to expand...
Click to collapse
This worked for me also!:laugh:
Related
Hello,
about 2 hours ago I decided that I would unlock my device (before that I read maximum informations that I could). Unlocking went fine and I also installed TWRP 2.1.3 (through ViperMod). So far so good.
Then I made backup in TWRP in case something goes wrong. I was going to try AOKP v40 so I downloaded it via goo manager and then I flashed it in TWRP Install option (and also installed gapps) and wiped cache. Device rebooted and I was stuck at AOKP boot animation for about 15 minutes when I decided to recover back. So I rebooted, restored and rebooted.
Now I'm stuck at first boot logo (eee pad). When I try to do VolDown+Power to get into recovery it doesn't ask for VolUp, but goes straight to selection of Wipe or USB. When I select fastboot or wait 10 secs device frozes. (I haven't tried wipe, just in case it would be needed to unbrick).
I read thread about unbricking (http://forum.xda-developers.com/showthread.php?t=1514088) and to me it seems like option 3, but I don't see recovery option.
In device manager I have 'ASUS Fastboot Interface'.
Here's video how it looks like: http://www.youtube.com/watch?v=7BGd1PIVbn8
Please please could anyone help me?
Btw: Is there any chance to shut down? Holding power button just resets, so does pinhole... :/
qery said:
Hello,
about 2 hours ago I decided that I would unlock my device (before that I read maximum informations that I could). Unlocking went fine and I also installed TWRP 2.1.3 (through ViperMod). So far so good.
Then I made backup in TWRP in case something goes wrong. I was going to try AOKP v40 so I downloaded it via goo manager and then I flashed it in TWRP Install option (and also installed gapps) and wiped cache. Device rebooted and I was stuck at AOKP boot animation for about 15 minutes when I decided to recover back. So I rebooted, restored and rebooted.
Now I'm stuck at first boot logo (eee pad). When I try to do VolUp+Power to get into recovery it doesn't ask for VolUp, but goes straight to selection of Wipe or USB. When I select fastboot or wait 10 secs device frozes. (I haven't tried wipe, just in case it would be needed to unbrick).
I read thread about unbricking (http://forum.xda-developers.com/showthread.php?t=1514088) and to me it seems like option 3, but I don't see recovery option.
In device manager I have 'ASUS Fastboot Interface'.
Here's video how it looks like: http://www.youtube.com/watch?v=7BGd1PIVbn8
Please please could anyone help me?
Btw: Is there any chance to shut down? Holding power button just resets, so does pinhole... :/
Click to expand...
Click to collapse
Shouldn't it be volume and power down to get to the option to press volume up for recovery?
Are you familiar with fastboot flashing recoveries? Either way that will be helpful info for us to have.
Most important thing, this is no big deal at all, it's really a minor issue. Don't let yourself get stressed out over it, the community will make sure you're good to go.
CharliesTheMan said:
Shouldn't it be volume and power down to get to the option to press volume up for recovery?
Click to expand...
Click to collapse
Yes sure my bad, it was typo (I was kinda sleepy and tired when I was writing)
CharliesTheMan said:
Are you familiar with fastboot flashing recoveries? Either way that will be helpful info for us to have.
Click to expand...
Click to collapse
Nope, this is my first time flashing.
You say you dont see the VOL_UP message. From the video it looks like it is there. You just did not press it within 5 seconds.
Once it comes up, let go of the buttons ;p
leppie said:
You say you dont see the VOL_UP message. From the video it looks like it is there. You just did not press it within 5 seconds.
Once it comes up, let go of the buttons ;p
Click to expand...
Click to collapse
nope it's not there. I was holding voldown from the start and as soon as it should say 'press volup for recovery' (time 0:04) it jumps (skips 5 seconds of waiting) directly to wipe/fastboot options (wipe is one that is selected on video)
Ok so I managed to fix my problem thanks to hanzo001's thread (http://forum.xda-developers.com/showthread.php?t=1662158). Someone should add this instructions to the [HOW-TO] Unbrick your Transformer Prime (or not) thread.
qery said:
Ok so I managed to fix my problem thanks to hanzo001's thread (http://forum.xda-developers.com/showthread.php?t=1662158). Someone should add this instructions to the [HOW-TO] Unbrick your Transformer Prime (or not) thread.
Click to expand...
Click to collapse
glad it's fixed, im sure hanzo001 will appriciate a simple thanks on his thread too..and let others know it worked for you
I'm trying to update from an ICS bootloader to a JB one, however when I try to go through the process of starting up in the Fastboot mode, as soon as I hit the Vol Up key, it just sits there with the text saying it is starting the Fastboot mode. I let it sit for a while to see if it was going to do something, but it doesn't. The computer doesn't recognize it at all with it stuck at this screen, and I assume there is supposed to be some sort of new view that comes up. I haven't done anything previously on my Prime other than unlocking it, which was a while ago, but I didn't do anything past that, so I'm not sure what could be going on, it is not bricked and works completely fine other than not being able to get into the fastboot mode. Anyone have any idea what may be wrong?
myselfalex said:
I'm trying to update from an ICS bootloader to a JB one, however when I try to go through the process of starting up in the Fastboot mode, as soon as I hit the Vol Up key, it just sits there with the text saying it is starting the Fastboot mode. I let it sit for a while to see if it was going to do something, but it doesn't. The computer doesn't recognize it at all with it stuck at this screen, and I assume there is supposed to be some sort of new view that comes up. I haven't done anything previously on my Prime other than unlocking it, which was a while ago, but I didn't do anything past that, so I'm not sure what could be going on, it is not bricked and works completely fine other than not being able to get into the fastboot mode. Anyone have any idea what may be wrong?
Click to expand...
Click to collapse
That is how fastboot works. If you look in device manager on your PC you may see it near the top of the devices. you may need to install the drivers. the universal naked drivers in the development section should work if your pc is looking for drivers for the device
Okay, thanks, it was working the whole time then.
My problem now is, I've been trying to initiate the install of both the JB bootloader and Hairybean TWRP Updater (normal), but no matter what I seem to do, I can't seem to get it to be installed. When I go into the recovery screen, it only shows the wipe data, fastboot, and load android, there's nothing to get into TWRP.
myselfalex said:
Okay, thanks, it was working the whole time then.
My problem now is, I've been trying to initiate the install of both the JB bootloader and Hairybean TWRP Updater (normal), but no matter what I seem to do, I can't seem to get it to be installed. When I go into the recovery screen, it only shows the wipe data, fastboot, and load android, there's nothing to get into TWRP.
Click to expand...
Click to collapse
Hold vol down+power and when it vibrates, let go of power. As soon as the screen shows something press volume up, that will start recovery.
myselfalex said:
Okay, thanks, it was working the whole time then.
My problem now is, I've been trying to initiate the install of both the JB bootloader and Hairybean TWRP Updater (normal), but no matter what I seem to do, I can't seem to get it to be installed. When I go into the recovery screen, it only shows the wipe data, fastboot, and load android, there's nothing to get into TWRP.
Click to expand...
Click to collapse
Go to post 2 of the androwook thread and follow instructions there for updating from ics
skaforey said:
Hold vol down+power and when it vibrates, let go of power. As soon as the screen shows something press volume up, that will start recovery.
Click to expand...
Click to collapse
Okay, I did that too, but it just resets the device and if I do nothing it loads into Android.
whycali said:
Go to post 2 of the androwook thread and follow instructions there for updating from ics
Click to expand...
Click to collapse
Sorry, I neglected to mention I actually have been doing all of my work based on these very instructions from the androwook page, and it is where I ran into this issue in the first place. I see now based on the skaforey's post that pressing volume up should be the way into recovery, however as I stated to him, it simply resets the device. After restarting with the power + voldown button, let go, and hit volume up (press vol up in 5 seconds to enter RCK), it waits a second, then restarts.
Update before I even bothered to submit this last section: I installed CWM via fastboot, which then enabled me to actually enter a recovery, which then let me install the JB bootloader update and thusly HairyBean. Thanks for all your guys help.
I was doing a backup with TWRP and everything seemed to go just fine. Then after a reboot i unlocked the phone to notice that it was leaving the lock-screen icons on the bottom of the page. I still had access to my notification bar and could clear notifications. Figuring that there had just been a mistake in the boot process, I held the power button to restart the phone. Well it never brought up my power menu to restart. Also instead of making me wait ten seconds until it flashed its lights and restarted, it just restarted in like 3 seconds. Now my phone is stuck on the HTC ONE screen and will not respond to anything including hold the power button.
My phone is rooted an s-off. I know that I have not posted at all on here, but I have been rooting and know how at least the basics on adb shell. I just have never had a phone lock up to this point. If I can at least get to recovery, I should have 2 or 3 backups to run. I just don't want to have to wait for the phone battery to die just to hope I can get to recovery.
TugboatTony said:
I was doing a backup with TWRP and everything seemed to go just fine. Then after a reboot i unlocked the phone to notice that it was leaving the lock-screen icons on the bottom of the page. I still had access to my notification bar and could clear notifications. Figuring that there had just been a mistake in the boot process, I held the power button to restart the phone. Well it never brought up my power menu to restart. Also instead of making me wait ten seconds until it flashed its lights and restarted, it just restarted in like 3 seconds. Now my phone is stuck on the HTC ONE screen and will not respond to anything including hold the power button.
My phone is rooted an s-off. I know that I have not posted at all on here, but I have been rooting and know how at least the basics on adb shell. I just have never had a phone lock up to this point. If I can at least get to recovery, I should have 2 or 3 backups to run. I just don't want to have to wait for the phone battery to die just to hope I can get to recovery.
Click to expand...
Click to collapse
Are you saying volume up + power button does not restart your phone nor does any help? Check if your phone is detected in computer and if so you can issue and adb reboot command
also since there is no removable battery HTC added a reboot function press home vol down and power that should do the trick
The phone is not detected by a computer, nor will it charge. Vol down and power is not cutting it off. Right now I am waiting for the battery to die so I can hopefully boot into recovery and do a restore.
Vol up + Power was the key. I was thinking it was volume down. Thanks for all your help
TugboatTony said:
The phone is not detected by a computer, nor will it charge. Vol down and power is not cutting it off. Right now I am waiting for the battery to die so I can hopefully boot into recovery and do a restore.
Click to expand...
Click to collapse
Its volume up mate + power not volume down
pradeepvizz said:
Its volume up mate + power not volume down
Click to expand...
Click to collapse
Hi Do you have a HTC one max stock Rom I could use??
Thanks
mini88448 said:
Hi Do you have a HTC one max stock Rom I could use??
Thanks
Click to expand...
Click to collapse
There have been lots of request for this, ill upload a stock rooted ROM soon.
pradeepvizz said:
There have been lots of request for this, ill upload a stock rooted ROM soon.
Click to expand...
Click to collapse
OMG THANK YOU SO MUCH!!!
:victory::victory::victory:
Just wanted to point out I ran into this issue also (Stuck on white HTC boot screen) after wiping my ROM and Vol UP + Power did the trick for me also (and then Vol Down + Power to get back to the bootloader).
i need help, guys
so attempting to install a new rom, i must have dont something wrong because now restarting the phone will leave me on the htc logo loop and restart. i still have access to hboot and fastboot. but when attempting to load into twrp, it shows the team win logo for half a second and then restarts the phone. then i installed cwm and it does boot into it but whatever option i pick, install zip, wipe data, ANYTHING, restarts the phone.
i have no idea what to do. i tried installing a rom using adb sideload but it stops at around 80%, ive tried installing different versions of twrp and cwm and same thing. i think it is bricked. im using the verizon htc one max. the only option i see left is the ruu toolkit but ive only been able to find the sprint version and then it says that bootloader needs to be locked and i have not idea how to do that from hboot, fastboot, or cwm
attempting to install superuser also fails
if there's anyone here that can help, please, any suggestions will be appreciated. thanks =:laugh:
Sounds like you're flashing the wrong TWRP.
Sent from my Galaxy Nexus using Tapatalk
suieitori said:
so attempting to install a new rom, i must have dont something wrong because now restarting the phone will leave me on the htc logo loop and restart. i still have access to hboot and fastboot. but when attempting to load into twrp, it shows the team win logo for half a second and then restarts the phone. then i installed cwm and it does boot into it but whatever option i pick, install zip, wipe data, ANYTHING, restarts the phone.
i have no idea what to do. i tried installing a rom using adb sideload but it stops at around 80%, ive tried installing different versions of twrp and cwm and same thing. i think it is bricked. im using the verizon htc one max. the only option i see left is the ruu toolkit but ive only been able to find the sprint version and then it says that bootloader needs to be locked and i have not idea how to do that from hboot, fastboot, or cwm
attempting to install superuser also fails
if there's anyone here that can help, please, any suggestions will be appreciated. thanks =:laugh:
Click to expand...
Click to collapse
May I suggest following these instructions?
http://forum.xda-developers.com/showpost.php?p=51753483&postcount=129
If you're able to complete those instructions outlined in that post, this should set you up with the latest HBOOT, Radio and TWRP (Recovery) for the Verizon HTC One.
Make sure you read the post fully before you start, especially this part:
fastboot flash zip firmware.zip (Be sure it finishes saying 'successful', not 'please flush again immediately'. If it says the flush again, rerun the command)
If you succeed in getting that done, see if TWRP still causes the phone to reboot and get back to us.
Hello everyone! I have a wonderful issue that I need to address and need some help with.
I will start with the fact I made the mistake of flashing the Cm12.1 10/5 Nightly. For those of us who do not know, this rom does not boot. It optimizes apps, then the Cyanogenmod boot logo shows up, and it does this, forever.
Shouldn't be a problem if I boot into recovery, right? Power and Volume down button should do the trick. My Lg g3 for some reason has never, ever been able to boot into recovery from the hardware keys. So this is where I am stuck, I do not want to go back to stock and clear my phone. I want to enter recovery and flash backwards, but have no way to. Is there a way with Download mode that I can flash a CM rom onto m phone, without getting rid of TWRP, and without wiping my device, and retaining root?
eddytheyeti2 said:
Hello everyone! I have a wonderful issue that I need to address and need some help with.
I will start with the fact I made the mistake of flashing the Cm12.1 10/5 Nightly. For those of us who do not know, this rom does not boot. It optimizes apps, then the Cyanogenmod boot logo shows up, and it does this, forever.
Shouldn't be a problem if I boot into recovery, right? Power and Volume down button should do the trick. My Lg g3 for some reason has never, ever been able to boot into recovery from the hardware keys. So this is where I am stuck, I do not want to go back to stock and clear my phone. I want to enter recovery and flash backwards, but have no way to. Is there a way with Download mode that I can flash a CM rom onto m phone, without getting rid of TWRP, and without wiping my device, and retaining root?
Click to expand...
Click to collapse
Getting in factory-reset screen (power and volume down) was tricky for me too till I figured out that "do not wait for lg logo to show up, as soon as phone vibrates release vol down and power then immediately press them together again, keep it pressed till the factory reset/safe mode screen shows up". It worked from me everytime since then.
Hopefully someone can help me, my child has a Pendo Pad 7 Model no.PNDPP44QC7 with Kitkat 4.4 and it ended up with lots of malware/viruses and barely usable. This tablet only has a power button and no other buttons so I did not know how to boot into recovery mode to do factory reset and after trying reset through settings which made no difference so I gave the device ROOT access so I could try and delete the malware etc but of course i did not do any sort of backup and did not add CWM or TWRP recovery. I ended up deleting something wrong and now the device just hangs on the Pendo logo screen. I have since worked out how to boot into Recovery Mode and also Fastboot mode now but a bit too late I tried to do a wipe data/factory reset and this made no difference still hangs on Pendo logo.
I can't seem to find a CWM or TWRP image file to suit the tablet and possibly try putting tablet into fastboot mode and using ADB on computer and flash the recovery to tablet. ???
in recovery mode options i get are
apply update from ADB
apply update from sdcard
apply update from cache
wipe data/factory reset
wipe cache partition
backup user data
restore user data
but i can not seem to find any correct files to work with this tablet any help to get this tablet working again would be much appreciated Thanks
Good day! how did you manage to boot into Recovery Mode or Fast Mode?
After pressing the power button and seeing the display turn on. Keep spamming the power button and a menu will pop-up on screen with boot options. Short press of the power button cycles through the options, long press selects the option.
Mine was also stuck on a boot loop, even though I had not played around with any settings or tried to root etc. I was able to revive it by going into recovery mode and doing a factory reset.
Hey OP I've got hold of the same tablet I'm working on getting a rom dump atm. Bare with me I'll try and send a link for the img. If u can get into recovery mode where u can update zip. That's good if not try and via pc. Once u have a link to the tablets boatloader, rest is history.
Hi,
Wondering if I can follow up on this.
Mine is stuck on the PENDO boot screen, and I have tried the reset button, as well as the se commands PENDO suggested....
1. Press On/Off Switch (Power), wait for the Pendo Logo start up screen, and then press On/Off Switch (Power) twice right away.
2. Factory mode menu comes out after 10 seconds, two fingers touches panel together to move to select the one like the following picture shows (no need to understand the Chinese words, just follow through as what the picture shows)
3. Press On/Off Switch (Power) and the following picture below will show, press On/Off Switch (Power) again to proceed on Recovery Mode, and wait for system to restart.
Unfortunately, nothing still happens.
ADB will not reveal what device it is, nor will Win 10 recognise the device for it to show in Device Manager or connected devices.
Windows responds with a ding ding, but nothing shows up.
I am stuck, and any info gladly accepted.
Thanks
bump please
ozviewer said:
Hi,
Wondering if I can follow up on this.
Mine is stuck on the PENDO boot screen, and I have tried the reset button, as well as the se commands PENDO suggested....
1. Press On/Off Switch (Power), wait for the Pendo Logo start up screen, and then press On/Off Switch (Power) twice right away.
2. Factory mode menu comes out after 10 seconds, two fingers touches panel together to move to select the one like the following picture shows (no need to understand the Chinese words, just follow through as what the picture shows)
3. Press On/Off Switch (Power) and the following picture below will show, press On/Off Switch (Power) again to proceed on Recovery Mode, and wait for system to restart.
Unfortunately, nothing still happens.
ADB will not reveal what device it is, nor will Win 10 recognise the device for it to show in Device Manager or connected devices.
Windows responds with a ding ding, but nothing shows up.
I am stuck, and any info gladly accepted.
Thanks
Click to expand...
Click to collapse
not working in my pendotab window 8
Hi,
I could get no further with mine, the same as you.
I contacted Pendo Support, and explained it would work but not boot, I even asked for the image file so I could reload it in recovery mode, however, they did not have access to it, the Chinese manufacturer had not made it available to them.
As I described it was not damaged, but simply not working, they agreed to send me a replacement, even though it was out of warranty, as really, as I said to them, it was not fit for purpose.
I had to send the old one back, but they sent me a satchel in which to do so, at no cost to me.
They sent me the new one very promptly.
Hope is not lost,
Someone has finally manage to extract the factory ROM for the pendo PNDPP44QC7. Just search the model number on needrom.
phoenixemer.blogspot.com.au/2017/04/pendo-pad7-pndpp44qc7.html
password : emerlitspendotab7
TWRP custom recovery
drive.google.com/open?id=0B3k_2dFOmDBGRmljV3JuSUZiUkU
I tried to upgrade a similar device to 5.x, some changes, but some options now not working I have a clone Q88H device, A33 quadcore processor 7" clone. Kernel 3.4.39, firm ware 2.1 Need to go back to 4.4.2 w latest update. Hopefully Play store will work again, as I need it. That, or change to windows version. advice pls?
drusid said:
Hope is not lost,
Someone has finally manage to extract the factory ROM for the pendo PNDPP44QC7. Just search the model number on needrom.
phoenixemer.blogspot.com.au/2017/04/pendo-pad7-pndpp44qc7.html
password : emerlitspendotab7
TWRP custom recovery
drive.google.com/open?id=0B3k_2dFOmDBGRmljV3JuSUZiUkU
Click to expand...
Click to collapse
Please i dont have a needrom account i cant download plz who Can send me the direct link to m'y account