HELLO TO STAFF
i hv hcl me u1 tablet. and it is behaving weird. last time i try to install a iron man 3 game and wont install so i get it at my shop.
(actually it belongs to my kids).. i do all reset. and delete things but nothing is working
i go in recovery and wipe formatt .. but nothing is being deleted.. all thing is as it is.
no new thing is being copy or being deleted in it..
so i open it and try to short it out. rediculously i found one more sd card of 4gb inside tablet chip.
i remove and put it in reader . connect to pc. it shows 1.8gb total and free around 800mb.
i guess rest of part is rom part in sd card bcouse without that memory chip tablet is not booting up. i replace another 4gb and 8gb but nothing working..
and i put back that sandisk 4gb back in hcl chip and it boots up as regular ...
problem is it is not being formated or not being hard reset in recovery.. i use MPTOOL . i updated with it. but nothing working out for new game or installations
for me the only solution left is to replace that 4gb SANDISK sd card which might cotain rom part..
so how to make that vimicro disk to make tab work normaly...
i attach the photo of board with sd card installed..
i hope some HCL GUY can help me..
solved hcl me u1
problem sloved
by updating with mptool with new sd card of 8 gb. in boot mode without sd card than insert sd card
it takes lot time and two time factory reset .. but working now but ram is as low below 300 mb
any body hv problem with hcl me u1 with hanging restarting or anything is not installing and deleting
change sd card of your choise 8gb or more and install rom
any question can ask me i just solved it
regards
skhan
Similar problem in HCL ME V1, but no solution so far
Hi,
I have an HCL Me V1 tab. My problem is something similar to yours. I was copying an apk (FL Studio Mobile) and a folder related to it (extra downloadable contents) from my laptop to the tablet (from laptop to /sdcard/Android/obb). Basically I had downloaded the apk and dlc from Pirate Bay. I'm sure there was no problem with these files as I had not even run these files in the tablet when the problem started.
First my laptop got hanged, but somehow I disconnected the tablet safely. However after I rebooted the tablet, it got stuck in a loop in the boot screen. I tried resetting it but it did not work. Also for some reason I am not able to do a hard reset on that tablet. The device simply refuses. When I remove the external SD card, the device won't even start when I press the reset pin hole.
There is one peculiarity to my problem however. The power button has stopped working. I can only start the tablet by the reset pin hole. I am sure this is not a hardware issue as I am 100% positive the tablet did not experience any physical shock.
It is a rooted device with rooted apps. Android ICS 4.0.4, kernel 3.x.x.
I plan on doing exactly what you did, i.e. open up the device, get a new sd card, load the ROM on it and put it back in. However, can you suggest any other alternatives before I do that?
Thanks,
Pari
Thanks!
I once encountered the same problem exactly as you described, but the device was in warranty and the service center fixed it.
Now i know what was the issue.
Thanks for your efforts because the i believe that it will help everyone who owns it as it will encounter problems with the device as HCL fooled us everyone with this model.
hcl me u1 is acting like crazy.
Hello ,I'm Kaushik Chauhan.
i have hcl me u1 tablet.
it is behaving crazy.
I can't save data on it.
whenever I restart it ,it is reset.
I tried to do factory reset, but nothing is changed.
I have also opened it and take out that internal sandisk of 4 gb.
inserted it mmc reader and connect it to ubuntu.
however I am not able to mount it.
but I managed to view partitions on it.
to my surprize,
there are six(believe me) partitions.(thanks to DISK UTILITY)
1. maximum size 2.5 gb. which I see in.xplore.
2. system 700 mb
3. data 400 mb
4.tmp 40 mb
5. and 6 are unallocated (I think).
(I will upload screenshot of it.soon)
but I am not able to mount any of it.
that 2.5 gb is fat32 but when I tried to mount it I got some superblock type error.
what is the problem.
and why xplore (file manager) shows two sd cards each of size 2.5 gb.(and identical to one another in context of files and folder.)
however its spec says 4 gb.(I have not attached any external sd or pendrive)
so here is my sd card partitions::
1:: 2.6 GB FAT :: that is what i see in file manager:: I can mount it.
2:: 1.3 GB Extended :: What is it? . there is no option to Mount it in Disk Utility.(Only one option 'Delete Partition').
3:: 403 MB ext2 :: I cant mount it.
(Error :: "Error mounting: mount: wrong fs type, bad option, bad superblock on /dev/sda5, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so" )
4:: 786 MB ext2 Userdata :: same as system ("Error is also same")
5:: 67 MB ext2 cache :: same as system ("Error is also same")
6:: 34 MB unknown :: only three option (Format Voulme,Edit Partition,Delete Partition)
7:: 34 MB unknown :: same as above
sam1skhan said:
problem sloved
by updating with mptool with new sd card of 8 gb. in boot mode without sd card than insert sd card
it takes lot time and two time factory reset .. but working now but ram is as low below 300 mb
any body hv problem with hcl me u1 with hanging restarting or anything is not installing and deleting
change sd card of your choise 8gb or more and install rom
any question can ask me i just solved it
regards
skhan
Click to expand...
Click to collapse
Thank you i finally reset my internal sd card..but as you said my tablet is very slow and always hang then turn off..is there any way solve this problem?
@cyberking147.and mixxskratch, pborah88
my tab is again corrupted and not being reset or copy data or delete data from it... may b the reason i found out is tab stays non used or on low charge bettery
or the poor quality of sd card which i replaced..
i am willing to replace with the original sandisk or the samsung class 8 or something best quality with some warranty....
slow tab >>>it may b due to sd card becoz this fools install rom on sd card. can you believe it?? i was shocked
i will post results when i replace another sd card of samsung class 8 of 8gb..
one more thing you can also extend your internal memory of tab by replacing the provided 4 gb.. 8gb will give you 5 gb of free internal storage..
this may help those whose mmc slot and usb are not working
regards
skhan
sory for late reply coz i dont see any notification in msgs
so sory
Thank You...I replaced my internal 4gig sd card of 8gig.still it;s hang and slow
mixxskratch said:
Thank You...I replaced my internal 4gig sd card of 8gig.still it;s hang and slow
Click to expand...
Click to collapse
did you check the ram..
do you know the ram before?
there are options in selecting ram ,
if you hv flashed rom with 512 ram selection it will b slower .
there are two models they(hcl) hv launched. 1 512mb ram and 2, 1 gb ram...
1gb ram was lilttle more speedy than of 512.
go to settings and apps and check ram in RUNNING...
NOT MUCH WE CAN DO WITH IT. COZ ITS REALLY OLDIE
TRY TO FLASH WITH 1GB SELECTION , IF YOU GOT BOOT LOOP. HANG ON HCL LOGO THAT MEANS YOU DNT HV 1GB RAM MODEL. YOU HV TO FLASH IT AGAIN WITH 512 SELECTION
EVEN ONE OF MY FRIEND HV ONE GB CONFIGURATION WRITTEN ON BOX AND 512 IN DEVICE..
REGARDS
SKHAN
sam1skhan said:
did you check the ram..
do you know the ram before?
there are options in selecting ram ,
if you hv flashed rom with 512 ram selection it will b slower .
there are two models they(hcl) hv launched. 1 512mb ram and 2, 1 gb ram...
1gb ram was lilttle more speedy than of 512.
go to settings and apps and check ram in RUNNING...
NOT MUCH WE CAN DO WITH IT. COZ ITS REALLY OLDIE
TRY TO FLASH WITH 1GB SELECTION , IF YOU GOT BOOT LOOP. HANG ON HCL LOGO THAT MEANS YOU DNT HV 1GB RAM MODEL. YOU HV TO FLASH IT AGAIN WITH 512 SELECTION
EVEN ONE OF MY FRIEND HV ONE GB CONFIGURATION WRITTEN ON BOX AND 512 IN DEVICE..
REGARDS
SKHAN
Click to expand...
Click to collapse
I don't know how to check the ram. If i use again the mptool can i change the settings to 1gig ram? and how to do it?
12 2828545
Hcl ME u1 hardware looks similar to BSNL penta is703c. I just installed the official stock rom of HCL u1 to my penta tab. IT does seem to work..
oh yeah, i changed SD card to 32 Gig...
using mp tool, try using different DDR settings.. (Check attachments)
mixxskratch said:
I don't know how to check the ram. If i use again the mptool can i change the settings to 1gig ram? and how to do it?
Click to expand...
Click to collapse
go to settings > application manager> slide to see running app. at the bottom u can find the ram and the free ram and used ram
the tab only can support 1g ram if it is build with that . some tab come with 512 and some with 1g.b
so try various selection in mp tool > go to ddr setting. select elpida or micron wich supports u that u will have to find out. and be patient after flashing dont do any fulish. if it does not work it wil go in boot loop . just hcl and nothing. than try other selection like elpida or micron.
to go in boot loader mode u need to remove mmc and data cable and than
insert data cable nd press power on button u find the disk iand vdfu driver will install and than put 4 gb or 8gb mermoy card and flash it
regards
skhan
HCL ME tablet U1
Sir,
My hcl tablet is behaving awkwardly. firstly, after every 4 to 5 weeks it starts hanging up and i have to send to centre to fix it. secondly, Everything gets stopped be it settings, gallery, file manager or anything and i have to factory reset it and loose every game i installed. But curiously this time i dont know what happened and i cant even factory reset it! it just reboots and nothing else. Even when i uninstall an app, it reboots again and what i see is that the app hasn't been uninstalled and it appears again! the only thing that works at its best is the calculator.
Suggest me what to do.
Hoping a reply as soon as possible
Thank you
-Yaagyanika
HCL me u1 WILL NOT RESET anymore..
Hey Everybuddy, ( Frusteted with HCL ME U1)
This is KAUSHIK CHAUHAN
I have solved the problem of it being reset evertime we restart it.
things you need ::
1 :: A new MicroSD card ( I prefer (actually used ) Sandisk Mobile Ultra 8gb Class 10).
I brought it from Flipcart for just Rs.340 .
2 :: Stock ROM for our tab , Dont download any other rom they have some performance issue
Here is Link :: xww.hclsupportservice.in/Drivers%5CFamily%5CTablet%5CCategory%5CHCL_ME_Tablet%5CU1%5CImage%5CU1_0421_Image.rar
3 :: A PC running windows.
After Having these 3 thing ....
Steps ::
1 :: take rear cover of tab , take that metal cover over circuit.
see that sandisk microsd 4 gb ?
that's the problem ! take it out.
and put new sd card there.
now fit rear cover again as it was .
DONT TRY TO TURN ON THE TAB
on to the computer ::
connect tab with pc via USB cable. (in Switched OFF state.)
U should see a new drive in my computer (dont open and close that popup window)
2 :: Extract file U1_0421_Image.rar
:: open mptool.exe ( I prefer run as Admin.)
:: U should see the message "1 device reddy".
if not Dont Worry .
3 :: then go to the setting on mptool.
select the "vortex.pak" for PAK File.
now the tricky part : Carefully
look at your tab specs ,
If it says RAM = 1 GB
then In partition setting set System(MB)=1024
and DDRtype = elpida 8bit 1024
If it says RAM = 512 MB
then In partition setting set
System(MB)=512
and DDRtype = elpida 8bit 512M
DONT TOUCH ANYTHING ELSE !
4 :: OK done ? then Save it .
5 :: now click on scan if it doesn't say "1 Device Reddy".
6 :: click on Update.
7 :: wait and let it complete.
8 :: now tab must be restart automatically. It will take some time for first boot so dont panic.
I hope u now have a working tab.
open apps and u will see "Market"
thats it !
Nowadays HCL is providing market app with new tab (I have not when i purchased it).
now it has market not play store
and it will not update itself.
so,
Find any android device with Google Play Store inbuilt.
open xplore on it (if it doesnt there just download it (nearly 2 mb))
in config set root = normal works on all device.
now go to /system/app
copy "vending.apk" file to sdcard and send it to OUR HCL ME U1 tab and install it .
after a network connection it will update itself.
and u can enjoy working latest play store.
thanks for reading..
Thanks a lot for your help
cyberking147 said:
Hey Everybuddy, ( Frusteted with HCL ME U1)
This is KAUSHIK CHAUHAN
I have solved the problem of it being reset evertime we restart it.
things you need ::
1 :: A new MicroSD card ( I prefer (actually used ) Sandisk Mobile Ultra 8gb Class 10).
I brought it from Flipcart for just Rs.340 .
2 :: Stock ROM for our tab , Dont download any other rom they have some performance issue
Here is Link :: xww.hclsupportservice.in/Drivers%5CFamily%5CTablet%5CCategory%5CHCL_ME_Tablet%5CU1%5CImage%5CU1_0421_Image.rar
3 :: A PC running windows.
After Having these 3 thing ....
Steps ::
1 :: take rear cover of tab , take that metal cover over circuit.
see that sandisk microsd 4 gb ?
that's the problem ! take it out.
and put new sd card there.
now fit rear cover again as it was .
DONT TRY TO TURN ON THE TAB
on to the computer ::
connect tab with pc via USB cable. (in Switched OFF state.)
U should see a new drive in my computer (dont open and close that popup window)
2 :: Extract file U1_0421_Image.rar
:: open mptool.exe ( I prefer run as Admin.)
:: U should see the message "1 device reddy".
if not Dont Worry .
3 :: then go to the setting on mptool.
select the "vortex.pak" for PAK File.
now the tricky part : Carefully
look at your tab specs ,
If it says RAM = 1 GB
then In partition setting set System(MB)=1024
and DDRtype = elpida 8bit 1024
If it says RAM = 512 MB
then In partition setting set
System(MB)=512
and DDRtype = elpida 8bit 512M
DONT TOUCH ANYTHING ELSE !
4 :: OK done ? then Save it .
5 :: now click on scan if it doesn't say "1 Device Reddy".
6 :: click on Update.
7 :: wait and let it complete.
8 :: now tab must be restart automatically. It will take some time for first boot so dont panic.
I hope u now have a working tab.
open apps and u will see "Market"
thats it !
Nowadays HCL is providing market app with new tab (I have not when i purchased it).
now it has market not play store
and it will not update itself.
so,
Find any android device with Google Play Store inbuilt.
open xplore on it (if it doesnt there just download it (nearly 2 mb))
in config set root = normal works on all device.
now go to /system/app
copy "vending.apk" file to sdcard and send it to OUR HCL ME U1 tab and install it .
after a network connection it will update itself.
and u can enjoy working latest play store.
thanks for reading..
Click to expand...
Click to collapse
Thanks a lot for your help... I could revive my HCL U1 tab I have inserted 16GB microSD card
about sd card and ram
not working in 8gb sd card and is there any way to get backn lost ram
and thanks for help
Storage problam
When i try to update my tablet it will disconnect on its own
what can i do????????
unable to flash hcl me u1
RAJWINDERS said:
When i try to update my tablet it will disconnect on its own
what can i do????????
Click to expand...
Click to collapse
Hi ,
same thing is happening with me. When I try to flash my u1 tab with mptool.exe,after 2-3 seconds it's givig a long beep and download error message is getting displayed .
plzz help anyone!!!!!!!!!!!!!!!!!
hcl me u1
how to install new rom in 8gb sdcard in hcl me u1
Hi Guys,
I have iball slide 3G 7334i IMEI S/N:911306700338238 tablet which have 16 GB internal memory and I don't have external sd card.
After installing a few apps it say Storage space is running out but the phone storage says 11.51 GB available
I have attached screen shots of storage.
The total internal storage is 16 GB of which only 1 GB is used to store apps and games.
What should I do to make use of total internal storage.
How to root this iball slide 3G 7334i tab& upgrade Android Jellybean OS 4.1.2 to upper version.
Please give the Ur valuable suggestion.
May be this will help you..
http://forum.xda-developers.com/showthread.php?t=2623672
iball slide 7334i
itechengine said:
May be this will help you..
http://forum.xda-developers.com/showthread.php?t=2623672
Click to expand...
Click to collapse
HI Friends,
I am trying to upgrade my iball Slide 7334i using the link http://forum.xda-developers.com/showthread.php?t=2623672
I have the following doubts:
1.) I did rooting. I need to check whether it is success or not. Rather how to check rooting happened or not.
2.) Do i need to take Custom rom backup before upgrading.
3.) How to do the upgrade after rooting, any app is there or any other way.
4.) Is there way i can do upgrade through USB mode as i am using Linux system.
Thanks in Advance for all the developers.
PG
Hi, i have a Qmobile Noir A110(its a chinese company,you can google it) and it has 175 internal memory. The problem is that its gets full after every hour and i have it tells me: "storage space running out. Some system functions may not work". If i dont clear data out of apps like facebook and messenger, after a while it will say that phone storage full and i cant run any app. This is getting really frustrating. Whenever i download apps, it says that insufficient memory on internal storage but my SD card has plenty of space. I have android 4.2.2 and there isnt a "preferred install location" option in the settings. I also did the android SDK thing which you can do to set the default install location to the external storage but still no luck. I heard that flashing a custom ROM is helpful so i rooted my phone using Mobogenie but i got completely lost at the flashing,unlocking bootloader etc. Can anyone tell me the solution to this? it will be really helpful.
Thanks
Dear developers,
Recently I got a new phone Vivo Y22 with Funtouch OS v1.0 (Christmas present). Its was okay at first then it start telling me that storage has not enough space (with only factory apps and Clean Master). I realize the it had about 4GB internal storage but divided to 2 parts. 2.5GB for system space and 1.06GB as internal storage. In system space, i have only 150mb left I always need to use Clean Master to wipe cache before I download anything. I tried Link2SD, I formatted my SD card and set 4GB partition as EXT2 but did not detect. Same goes for EXT3 and EXT4. It only works for FAT32 but some files cannot be linked using this format. Read some threads in web, they mentioned some phone does not support EXT2,3,4 format. Maybe this is my case? I tried to look for informations about Vivo Y22 but very less and worst, some of them is in chinese.
So the 1st question is: How can I increase the system space? Could I adjust the system space to occupy my more of my Internal Memory?
Second question is, how do I update my phone from JellyBean to KitKat? Do I follow tutorials that uses the same Chipset (Y22 uses MediaTek MT6582)? How if I want to install custom ROMs like CM11 (can't find Vivo Y22 in Device section in CM site so i presume it is not supported?)? There is very less information about rooting and flashing when it comes to this phone. I only manage to root the phone using tutorials given for some other chinese phone.
Thanks in advance..
By,
adlfurball
(just started using smartphone 3 weeks ago, was using old flip phones before hand)
Did you ever manage to fix this? I'd love to root my Y22 and put vanilla Android on there but can't find how to do it. The memory problem is useless on this phone.
Hello All.
I'm new here and this is my second adventure with android. For the first time i got my sisters old galaxy s3 i managed to flash custom rom in couple of hours never having android before (im a BB user). That was easy.
But now i bought tablet Overmax Steelcore 1020 3g Kitkat 4.4.2. and as soon as i started to install apps tablet runed out of memory. It has 16Gb in total but for apps its only 1 giga. Was trying to move apps to sd card via menu, then i rooted it and trying move apps via link2sd and a dozen of similar tools. It was half-working becouse most of apps cannot be moved and even if they can its still impossible to to install some big app or game. Its like it needs to be install on internal memory and after that moved to sd. I Even formated my sd card into 2 partitions fat and ext2/4 becouse it suppose to extend apps memory. It didnt. Its not even possible to run recovery mode. The only combination of buttons vol- and pow can run some diagnostic mode, but thats all. In my research i found some (edited to have more rom memory) EBR files wich i suppose to put and replace original files in rom(downloaded from developer website) but couldnt even flash original rom. This is not a popular device so its really hard to find some info about it. I would be really gratefull for some advices, or maybe some easy obvious method that i might have overlooked. Better solution for me would be repartition from 12giga storage/1 giga rom to 5 giga storage/8giga rom in internal memory couse i dont need space for my files and its rather safer having apps on tablet than sd. Thanks in advance for any advices.