Hello,
Yesterday i decided to root my xperia sola, and i did that, and I also did CWM recovery and right after, i tried to install a new ROM. I found some "XNovathor Project 4.1.2 V5" rom and followed the instructions....backed up, wiped everything, wiped cach and than I installed the rom from phone sd memory... it showed as if succesfully installed. Finally, the video guy says that i should reboot the device (the first option in boot window) and to wait as long as it takes. So I did...I rebooted it and it just turned off...i left it whole night, hoping it will boot up eventually, but it didn't...After I realised it wont, i tried to turn it on, but when i hold the power button, it's just vibrating every few seconds for half a sec as if it will turn on, but it doesn't. The light doesn't turn on, nothing shows up on screen....when i push the volume down and power button at the same time, along with vibrating, the led light goes green every few seconds. Only diffrence is that when i put it on the charger and than press volume down and power button, the led light turns green and it doesnt turn off untill i unplugg it. Is this what they meant when they said "bricked phone"? Thank you in advance, any advice is appreciated!
Try flash stock FTF file via flashtool if you can get into flashmode.
Try flash stock .54 kernel.
Sent from my MT27i using XDA Premium 4 mobile app
akshay788 said:
Hello,
Yesterday i decided to root my xperia sola, and i did that, and I also did CWM recovery and right after, i tried to install a new ROM. I found some "XNovathor Project 4.1.2 V5" rom and followed the instructions....backed up, wiped everything, wiped cach and than I installed the rom from phone sd memory... it showed as if succesfully installed. Finally, the video guy says that i should reboot the device (the first option in boot window) and to wait as long as it takes. So I did...I rebooted it and it just turned off...i left it whole night, hoping it will boot up eventually, but it didn't...After I realised it wont, i tried to turn it on, but when i hold the power button, it's just vibrating every few seconds for half a sec as if it will turn on, but it doesn't. The light doesn't turn on, nothing shows up on screen....when i push the volume down and power button at the same time, along with vibrating, the led light goes green every few seconds. Only diffrence is that when i put it on the charger and than press volume down and power button, the led light turns green and it doesnt turn off untill i unplugg it. Is this what they meant when they said "bricked phone"? Thank you in advance, any advice is appreciated!
Click to expand...
Click to collapse
yes it is soft brick,but don't panic you can retrieve it back to working condition.
i don't know which region are you from but you can download stock .54 FTF file from here http://forum.xda-developers.com/xpe...27i-xperia-sola-official-thread-root-t2273748
1.open flashtool
2.insert the usb cable holding the volume down button(green light should glow and flashtool will detect your phone in flash mode)
3.choose flash mode in flashtool and open downloaded FTF file into flashtool and perss flash button.
4.It's done power it on.
harshao said:
yes it is soft brick,but don't panic you can retrieve it back to working condition.
i don't know which region are you from but you can download stock .54 FTF file from here http://forum.xda-developers.com/xpe...27i-xperia-sola-official-thread-root-t2273748
1.open flashtool
2.insert the usb cable holding the volume down button(green light should glow and flashtool will detect your phone in flash mode)
3.choose flash mode in flashtool and open downloaded FTF file into flashtool and perss flash button.
4.It's done power it on.
Click to expand...
Click to collapse
Thankyou soo much...! Now its working fine.
Related
Hi guys, yesterday I unlocked and rooted my Xperia U, as I didnt have time anymore, I decided to install the kernel today, so when I installed it, I tried turning on my phone - nothing. I just got that red light thingy sometimes that is active 2-3 seconds, I tried charging but still nothing, funny thing is, when I connect it to my 2nd PC with XP on it, it connects, but in My Computer I only see "Digital Camera" and cant open it, also Windows Explorer popup for it keeps constantly, well, popping up but its empty and I cant select anything. I'm now downloading flashtool, is there anything I can do else? Im desperate, I got this phone for only 3 days.
Okay, now I'm in flashtool, I'm about to start flashing but I cant get into fastboot mode... What should I do?
Bump? :crying:
Please dont make me spam, I searched everything, I'm pretty sure my problem is unique, I cant access fastboot. Nothing
try this:
1. charge your phone for about 1 hour
2. open flashtool then click fastmode and choose your firmware.
3. make sure your phone is off ( i dont know if this is the same with xperia U volume up+power button wait til vibrates three times)
4. when it says connect your phone into fastmode, connect your phone via usb, then hold volume up + power button and wait till it vibrates three times, then hold power button+ volume down.
5. it will flash your firmware.
or you can flash the stock kernel (just extract from ftf, same instructions above).
I charged it for the whole night, the problem is, I cant access fastboot. All the drivers are installed but nothing.
I'm sending my phone for repair probably, with rooting I broke my warrant, what's going to happen?
tavic said:
I charged it for the whole night, the problem is, I cant access fastboot. All the drivers are installed but nothing.
I'm sending my phone for repair probably, with rooting I broke my warrant, what's going to happen?
Click to expand...
Click to collapse
Then y don't you flash it with your firmware via flash mode
Sent From Xperia Sola White (MT27i)
Rooted Stock ICS
Hit Thanks If I Helped!!
Ok fast boot doesn't work,how about Flashboot?
Sent from my LT26i using xda premium
Nope, can't access that either.
Ok does your phone vibrates when you turn it on?Do you have any LED light?Does it respobd to anything?
Sent from my LT26i using xda premium
Not vibrating, also, no led.
The only sign I get is when I take out the battery and put it back in, it vibrates for a second. Thats it.
Try to remove the battery and than try all keys combination,and also try to get to connect it to your flashtool.Try hard reset combination.Remove the battery,put the battery,hold power+vol. up button for. 20 sec. If that doesn't make.Try the same only with vol. down button .If that doesn't work,take it to the service shop than....
Hit Thaks if I helped
Hold vol up when replacing the battery, then quickly shove the USB cable in. Phone should vibrate when you put the battery in and you have a second or two to get it into fastboot or flashboot.
Probably a bad install of a kernel, make sure you're using the right one for your phone.
Not sure if it works for the U, but that's how I fixed my Sola.
Snowstormzzz said:
Hold vol up when replacing the battery, then quickly shove the USB cable in. Phone should vibrate when you put the battery in and you have a second or two to get it into fastboot or flashboot.
Probably a bad install of a kernel, make sure you're using the right one for your phone.
Not sure if it works for the U, but that's how I fixed my Sola.
Click to expand...
Click to collapse
Exactly what I did too. Try again and again. You'll succeed. have stock kernel at hand.
i was using some jelly bean sony rom by divaksh (it had cwm touch) and i wanted to try the new cm10.2 rom by munjeni
i downloaded the cm10.2, put it on my external sd card through a usb micro-sd reader and then put the µsd back in the phone
i selected "reboot to recovery" from the phone's power menu (i had an xposed module for more power menu options)
then i noticed that the phone didn't reboot, but it had turned off completely
i held the power button and the phone vibrated but didn't power on
it powered on on the second try, i then went to the cwm recovery by tapping the volume down key
(i was going to make a backup of the current system, but i forgot it lol)
i flashed the cm10.2 zip (cm10.2_pepper-ota-eng.root_Build.1.zip) without doing any wipes, because i wanted to get to the correct version of cwm recovery
(i would've properly done the wipes/formats from the cwm recovery that is in the cm10.2 kernel)
it finished flashing the zip and i rebooted my phone, but then it didn't power on anymore
now when i hold down the power button, the phone makes a short vibration but nothing else
.
if i plug the phone to a charger, the led lights up (red) for approximately a second and then turns off
if i hold down "volume-down" and the power button, the phone vibrates once and flashes the led (green)
i've tried going into flashmode and fastboot mode but the light doesn't stay on for long and sony mobile flasher doesn't even notice the phone even though the drivers are installed
the "hold down power button and vol-up"-thing also works but it doesn't seem to do anything else than vibrate
what should i do?
Is your bootloader unlocked?
If yes then flahs
Sent from my LT22i using XDA Premium 4 mobile app
Hamza Murad said:
If yes then flahs
Click to expand...
Click to collapse
what?
Is it unlocked?
When I bricked my xperia p I flashed a custom kernel which allowed me to enter Cwm and then flashed the stock rom. I am new to this flashing thing so I recommend that you ask someone experienced what to do. I just shared my experience of recovering from a softbrick. Don't flash new things blindly but ask someone experienced before doing so.
Sent from my LT22i using XDA Premium 4 mobile app
the bootloader is unlocked, and i'm not new to this "flashing thing"
anyone? the phone still hasn't woken up
download firmware for your p and flash using flashtool...
Osku958 said:
the bootloader is unlocked, and i'm not new to this "flashing thing"
Click to expand...
Click to collapse
Have you used flashtool to flash firmware before on that PC?
Have you installed flashtool and it's drivers (sola, flash & fastboot mode).?
Make sure the phobe is off, press power + volume up untill you feel 1 + 3 vibrations and see if it stay in flash mode longer.
Just Flash stock
i have nearly the same problem
my xperia u was running with 4.1 then i restored my ta backup its mine not for someone else then i pressed reboot instead of power off then my phone is dead no vibration no led except the one when i plug it to charger just one red led then nothing
AndroidNoob69 said:
Just Flash stock
Click to expand...
Click to collapse
how? the phone doesn't boot and flashtool doesn't recognize it
Same problem here, I think that Munjeni's post is bad written.
Ok, I fixed it, follow my instructions as they goes. You have to flash the .img kernel that CM10.2.zip comes from.
For flashing it, go as follows...
First try to install the following drivers, with Flashtool. The executable is in C:\\Flashtool\drivers
Run as adminsitrator and follow screen instructions, allow any driver install.
When it's ready, try to plug in the phone in fastboot mode (turn off, hold power and vol up and release power button, led has to turn blue/violet/pink, whatever, a color like that)
Run flashtool.
Flashtool will recognize the phone as the log says, if its not try to install drivers mannually.
If it's recognized then click the black lightning button and select fast boot mode.
At the right side click "Select kernel to flash" and browse the kernel that comes in the .zip. (in the file you've downloaded you have to extract a boot.ini because is the main kernel to make the ROM work, so you have to put somewhere else, I prefer desktop)
When selected, log writes all the procedure until it show an "OKAY[time]" message.
Finally click "Reboot device into system" in the center side and wait until boots.
It should be working now, I spent a lot of hours investigating, but finally I fixed, hope it works for you too!
If there's an error or some question, feel free to post.
manudo said:
Ok, I fixed it, follow my instructions as they goes. You have to flash the .img kernel that CM10.2.zip comes from.
For flashing it, go as follows...
First try to install the following drivers, with Flashtool. The executable is in C:\\Flashtool\drivers
Run as adminsitrator and follow screen instructions, allow any driver install.
When it's ready, try to plug in the phone in fastboot mode (turn off, hold power and vol up and release power button, led has to turn blue/violet/pink, whatever, a color like that)
Run flashtool.
Flashtool will recognize the phone as the log says, if its not try to install drivers mannually.
If it's recognized then click the black lightning button and select fast boot mode.
At the right side click "Select kernel to flash" and browse the kernel that comes in the .zip. (in the file you've downloaded you have to extract a boot.ini because is the main kernel to make the ROM work, so you have to put somewhere else, I prefer desktop)
When selected, log writes all the procedure until it show an "OKAY[time]" message.
Finally click "Reboot device into system" in the center side and wait until boots.
It should be working now, I spent a lot of hours investigating, but finally I fixed, hope it works for you too!
If there's an error or some question, feel free to post.
Click to expand...
Click to collapse
That was "the long run" for windows-guys.
For Linux - no drivers needed anyways - just download fastboot from anywhere and look for kernel. Put them in a personal directory. Open and run in a terminal (some have to be login as su) "fastboot flash boot kernel.img" (or whatever kernel is called...), plug phone in usb, while press and hold power and volume-up buttons. Blue LED comes shining and terminal tell you the flashing.
Unplug or type "fastboot reboot" to re-start phone.
Sure, you also can use FlashTool, too. But for only flashing a kernel it is not needed. Only for flashing stockrom ftf. But this is another story.
i happens to me yesterday
Hi ! Dont worry u r not the first to face this problem i also face this problem yesterday.. my phone was on JB 4.1.2 i download custom ICS rom and install it through CWM Recovery mode, when my new custom Rom starts it stucks on Boot screen and then nothing happens i tried but my phone was in danger... i was worried then i install flash tool and downlaod ICS Rom for Flastool and install that after severals trys i was now ion ICS v4.0.4..
Just Press volume up key and power simultanly when phone vibrtes three time leave it for 30 sec. and then run Flashtool and follow step to install another or same Rom for Falshtool & You r Done ...:good: Sorry for my bad english and type mistakes...
Osku958 said:
i was using some jelly bean sony rom by divaksh (it had cwm touch) and i wanted to try the new cm10.2 rom by munjeni
i downloaded the cm10.2, put it on my external sd card through a usb micro-sd reader and then put the µsd back in the phone
i selected "reboot to recovery" from the phone's power menu (i had an xposed module for more power menu options)
then i noticed that the phone didn't reboot, but it had turned off completely
i held the power button and the phone vibrated but didn't power on
it powered on on the second try, i then went to the cwm recovery by tapping the volume down key
(i was going to make a backup of the current system, but i forgot it lol)
i flashed the cm10.2 zip (cm10.2_pepper-ota-eng.root_Build.1.zip) without doing any wipes, because i wanted to get to the correct version of cwm recovery
(i would've properly done the wipes/formats from the cwm recovery that is in the cm10.2 kernel)
it finished flashing the zip and i rebooted my phone, but then it didn't power on anymore
now when i hold down the power button, the phone makes a short vibration but nothing else
.
if i plug the phone to a charger, the led lights up (red) for approximately a second and then turns off
if i hold down "volume-down" and the power button, the phone vibrates once and flashes the led (green)
i've tried going into flashmode and fastboot mode but the light doesn't stay on for long and sony mobile flasher doesn't even notice the phone even though the drivers are installed
the "hold down power button and vol-up"-thing also works but it doesn't seem to do anything else than vibrate
what should i do?
Click to expand...
Click to collapse
akkufix said:
That was "the long run" for windows-guys.
For Linux - no drivers needed anyways - just download fastboot from anywhere and look for kernel. Put them in a personal directory. Open and run in a terminal (some have to be login as su) "fastboot flash boot kernel.img" (or whatever kernel is called...), plug phone in usb, while press and hold power and volume-up buttons. Blue LED comes shining and terminal tell you the flashing.
Unplug or type "fastboot reboot" to re-start phone.
Sure, you also can use FlashTool, too. But for only flashing a kernel it is not needed. Only for flashing stockrom ftf. But this is another story.
Click to expand...
Click to collapse
If I wrote for Windows 8 there will be more than that, believe me. Managing Android with Linux is a lot easier, from flashing to programming.
But, face it, Windows is the standard here.
manudo said:
If I wrote for Windows 8 there will be more than that, believe me. Managing Android with Linux is a lot easier, from flashing to programming.
But, face it, Windows is the standard here.
Click to expand...
Click to collapse
That's why i'm working over 8 years till now with Linux.
Sorry, i'm new here, i've downloaded roms and some other stuff here, but now i have a serious problem. I had this GoogleBeAnZP rom on my phone (i had root, unlocked bootloader and CWM) and it was fine!!! actually it was running smooth, but i wanted to try another rom, i tried to instal a JB custom rom that i saw over the internet, so i entered the recovery mode and installed this rom with aroma installer. it said that everything was installed, and that it was going to reboot, so i waited, and NOTHING HAPPEND!!! now, i try to enter flashmode to instal the rom from flashtool and i can't even enter flash mode. my cellphone is really dead, all it does is turn a red light when i connect it. once it turned on the green light like when it enters flash mode but not anymore. I've hold the down button before connecting it, like a hundred times, trying to reboot the phone pressing the up volume button and the power button at the same time but its dead. it keeps showing the red LED indicator but not starting. i've been reading hundreds of posts but no cellphone does what mine does. i tried SEUS, flashtool but both require flashmode and I simply can't enter!!
All i get is this red light from the LED but no response in my phone. the screen doesn't blink neither vibrates
HEEELLLLP!!!!!
Hi,
I own a Xperia p, running honami moonwalker v8. Recently i decided to upgrade to CM11. I flashed the CM11 unofficial ROM from this website nightly 2 i think. I did a clean install (erase everything and clear cache) But when i pressed reboot (on cwm) i got a black screen. When you hold the power button it vibrates but screen doesnt turn on, the led goes red for about 2sec and goes off. i tried holding power button and volume up but same result, vibrates and nothing comes up. Even when I make it vibrate 3 times, no result. Im desperate guys please help me i will appreciate your help greatly. And if this means anything, when i installed zip from sd card, it just said installing, and after a few minutes, said install complete. Is this normal? since it didnt show anything in between. PLEASE HELP I WILL TRY DONATE TO WHOEVER FIXES MY PROBLEM.
someguyonearth said:
Hi,
I own a Xperia p, running honami moonwalker v8. Recently i decided to upgrade to CM11. I flashed the CM11 unofficial ROM from this website nightly 2 i think. I did a clean install (erase everything and clear cache) But when i pressed reboot (on cwm) i got a black screen. When you hold the power button it vibrates but screen doesnt turn on, the led goes red for about 2sec and goes off. i tried holding power button and volume up but same result, vibrates and nothing comes up. Even when I make it vibrate 3 times, no result. Im desperate guys please help me i will appreciate your help greatly. And if this means anything, when i installed zip from sd card, it just said installing, and after a few minutes, said install complete. Is this normal? since it didnt show anything in between. PLEASE HELP I WILL TRY DONATE TO WHOEVER FIXES MY PROBLEM.
Click to expand...
Click to collapse
Is your bootloader unlocked?
Can you enter flash/fastboot mode?
ChikeD said:
Is your bootloader unlocked?
Can you enter flash/fastboot mode?
Click to expand...
Click to collapse
how do i enter fastboot? no matter what i try, all i get is vibrations screen doesnt light up.
someguyonearth said:
how do i enter fastboot? no matter what i try, all i get is vibrations screen doesnt light up.
Click to expand...
Click to collapse
You did not answer my first question., therefore I am not going to answer yours
ChikeD said:
You did not answer my first question., therefore I am not going to answer yours
Click to expand...
Click to collapse
Ahahaah sorry i think i forgot about them and yes bootloader unlocked
someguyonearth said:
Ahahaah sorry i think i forgot about them and yes bootloader unlocked
Click to expand...
Click to collapse
1. Open flash tool (don't click anything)
2. Turn the phone off, power + volume up until you feel (1+) 3 vibreations.
3. Press the volume up key while connecting the USB cable, led should lit blue and connected in fastboot should be in the log.
4. Repeat 2, press volume down while connectiong the USB cable for flash mode, check flashtool log
If flash mode stays connected for about 45 seconds you can simply try to flash stock with flash tool.
If fastboot stays connected over 20 seconds you can flash custom stock based kernel and flash moonwalker again, or any other custom rom you have on the phone.
If none works, just leave it turned of, charging for one day then try again.
I've seen more than one report of people that recovered XP by disconnecting the battery, though it didn't work for others.
usually when i mess this phone up i am able to use the companion to flash it back to stock. i tryed to flash magisk and now the light flashes when plugged into a power source and the phone does not turn on at all. if i hold volume up while turning on it boots into fastboot mode because i see the blue light and i was able to use flashtool and its fastboot tools to flash system.sin from stock firmware but that has not made a difference. i have tried to get it into download mode(upgrade mode) by holding volume down but it continues to boot loop. if the device is not plugged into power and i hold volume down and power it boots into recovery and i click both safe mode and factory reset but both turn the device off. any ideas?
ths is far from beeig bricked. go into twrp recovery and flash new rom. this should work.
It is just a dead mobile
TjNiko said:
ths is far from beeig bricked. go into twrp recovery and flash new rom. this should work.
Click to expand...
Click to collapse
mine is not doing anything but it only boots into fastboot mode.
my device : Z3v D6708
rooted
no twrp is able to accessed.
dead body which blinks red+green LED when plugged in....and shows a blue light in fastboot.
Inside the SD card / SIM card slot is a small orange or red button, press with a tooth pick or a pin untill you feel vibration and then try to reflash.
a recovery shouzld be aways present at fota my friend.
rockinroller said:
Inside the SD card / SIM card slot is a small orange or red button, press with a tooth pick or a pin untill you feel vibration and then try to reflash.
Click to expand...
Click to collapse
i held the button in the sim card slot until the phone vibrated but what's next? i tried the companion and flashtool but the only thing it lets me do is flash the system, which does not fix my problem still, what is that button?
TjNiko said:
a recovery shouzld be aways present at fota my friend.
Click to expand...
Click to collapse
the only recovery available is the stock one that says power off, safe mode, continue boot, factory reset... none of them do anything....this device does have a locked bootloader, it uses a recovery like many motorola's do... its a software recovery so its gone lol
You should be able to use flash tool to flash the proper ftf file for your device. That is what you are trying to do right?
rockinroller said:
You should be able to use flash tool to flash the proper ftf file for your device. That is what you are trying to do right?
Click to expand...
Click to collapse
yes, every time i try it asks to put the device is upgrade mode, which it can not do at the moment
logan71f100 said:
yes, every time i try it asks to put the device is upgrade mode, which it can not do at the moment
Click to expand...
Click to collapse
So, if you hit the flash button on flashtool, tick the flashmode and after preparing it asks you to power off your phone and plug your USB cable into your computer and then press the volume button "down" while plugging in the USB cable to your phone, It should enter flashmode and start a automated flash. This is not working?
rockinroller said:
So, if you hit the flash button on flashtool, tick the flashmode and after preparing it asks you to power off your phone and plug your USB cable into your computer and then press the volume button "down" while plugging in the USB cable to your phone, It should enter flashmode and start a automated flash. This is not working?
Click to expand...
Click to collapse
nope thats my problem, i only can access flashmode, when plugged in it just bootloops, it only goes into flash mode via the blue light
logan71f100 said:
nope thats my problem, i only can access flashmode, when plugged in it just bootloops, it only goes into flash mode via the blue light
Click to expand...
Click to collapse
I'm not understanding how it is bootlooping. Your phone should be off (power off) when holding down the volume button and plugging in the USB. Is your phone powering on at this point to bootloop? If so you might have hardware problems Is all I can think of.
rockinroller said:
I'm not understanding how it is bootlooping. Your phone should be off (power off) when holding down the volume button and plugging in the USB. Is your phone powering on at this point to bootloop? If so you might have hardware problems Is all I can think of.
Click to expand...
Click to collapse
the phone started bootlooping after flashing that zip. so that rules out hardware, and when i say boot loop i mean lights flash screen stays dark..im trying to figure out if there's a fancy way to fix this through fastboot
depends on wich ftf was used before and bootloader some of them can enter flashmode just by put on the otg cable
It was running 5.1.1 and it boots into fastboot when I hold volume up, but just lights and virbates when holding down for upgrade mode
Same problem. z3v, accidentally flashed a wrong firmware zip via TWRP.
Now if I push the power button, nothing happens.
A long push causes a short vibration and nothing else.
Yellow rest button does not change anything either.
If I connect it to the PC, the following happens: Red led lights up briefly, phone vibrates, green led lights up briefly; whole sequence cycles after that. Now the only thing I can do from there is hold volume up for a couple of seconds, then the phone enters fastboot mode. Blue led lights up continuously. Flashtool sees the phone in Fastboot mode.
However, where to go from here, I cannot see. Any advise?
I had this problem once. It might be your usb cable try a brand new one that rated for data also not just charging. I was trying to root my phone at work and it wouldnt work and when I got home I tried a different usb cable and it worked.,
s300pmu1 said:
Same problem. z3v, accidentally flashed a wrong firmware zip via TWRP.
Now if I push the power button, nothing happens.
A long push causes a short vibration and nothing else.
Yellow rest button does not change anything either.
If I connect it to the PC, the following happens: Red led lights up briefly, phone vibrates, green led lights up briefly; whole sequence cycles after that. Now the only thing I can do from there is hold volume up for a couple of seconds, then the phone enters fastboot mode. Blue led lights up continuously. Flashtool sees the phone in Fastboot mode.
However, where to go from here, I cannot see. Any advise?
Click to expand...
Click to collapse
I am no closer than when I posted this, until there is a bootloader unlock witch in theory can be done through fastboot, we are s.o.l.
logan71f100 said:
I am no closer than when I posted this, until there is a bootloader unlock witch in theory can be done through fastboot, we are s.o.l.
Click to expand...
Click to collapse
aaa,It's very easy.you can use flashtool to flash a new system. but you must be in green light.only it.you also can be flash.sure,if your phone can't get into system,it only loop at"SONY".You touch the power and the volume up and down. keep 7s. then the phone will get into 3E RECOVERY,you chosed power down.and then the phonwill be power off. Now you can flash you phone.
If you phone can't get into green light.you can use the tool Z3X easy tool to save your phone.or it will be a brick.
my phone cant be start.it have became a brick. Good luck
s300pmu1 said:
Same problem. z3v, accidentally flashed a wrong firmware zip via TWRP.
Now if I push the power button, nothing happens.
A long push causes a short vibration and nothing else.
Yellow rest button does not change anything either.
If I connect it to the PC, the following happens: Red led lights up briefly, phone vibrates, green led lights up briefly; whole sequence cycles after that. Now the only thing I can do from there is hold volume up for a couple of seconds, then the phone enters fastboot mode. Blue led lights up continuously. Flashtool sees the phone in Fastboot mode.
However, where to go from here, I cannot see. Any advise?
Click to expand...
Click to collapse
I have same problem if you resolve it please help