I stupidly formated the memory of my Cubot One mt6589t without backup, i can install firmware V0.8 with flashtool,but the screen has issues, the screen is black with the backlight on, the phone works i could restore even the IMEI's, rooted the equipment via MTKdroid tools, i pushed the build.prop to enable usb debugging, i can see the screen via androidscreencast, even the phone can make calls and connect to wi-fi, but the screen stills black. Can some charity soul, post the g800_cubot_d1_v1.3_2014_03_28_mjk firmware for SP_flashtool, or a backup made in MTKdroid tools of the NVRAM?
Help Please....
:crying:
The process I followed was:
1. Disconnect the Cubot One if connected and installed mtk win7 drivers.
2. Open SP_flashtools v5.1343.01
3. Load the scatter file for V0.8 firmware (obtained from needrom webpage)
4. Remove Battery from cubot one
5. Selected "Format all + download"
6. Click download.
7. Connected Cubot One via USB cable.
8. The flashtool went normally, green indication.
9. Disconnected Cubot, i put the battery.
10. I powered phone (black screen, backlight on)
11. Removed battery
12. Turned on phone with pressing vol minus (-) at the same time with power button.
13. Still black screen, I connected to PC.
14. Loader detected.
15. Open MTKdroid tool, the phone is detected, no baseband visible.
16. Rooted device, installed superSU, succesfull.
17. Open an adb shell, then injected to the build.prop the instruction persist.service.adb.enable=1
18. Rebooted in normal mode.
19. The phone makes the boot sound as normally, still black screen with backlight on.
20. MTKdroid tool detects normally, granted superuser permits.
21. Change IMEI's with MTKdroid tool, rebooted.
22. Phone restarts normally, still black screen.
23. MTKdroid detects phone.
24. Opened on PC androidscreencast and can see the device screen on the PC.
25. Tested making a call and connecting to wi-fi, no problem, screen stills black.
So i think i made a mistake formatting the NVRAM of the device. I suppose with a newer stock firmware i can get back to normal the phone, in the other hand the phone is almost new with no physical damage.
Hello there!!
bump!
Up
Up. help please!
I'll bump it because I need help too, with something related, I lost the recovery mode and I had the same version the 1.3
Need help wit this too. Can anyone post link to this rom .Cant be found anywhere.g800_cubot_d1_v1.3_2014_03_28_mjk firmware
Related
my pantech sky vega a760s got soft bricked
here's what happened:
-the phone won't open unless connected to pc
-when connected, it will only go to charging mode
-when i try to enter recovery mode, this shows up:
"your phone will restart due to error occurred while running application "
i cannot access recovery mode, the only thing i can access is the s/w upgrade mode, which i don't know how to use since i'm not korean
and i can't understand pantech's website.
also, when i enter in fastboot mode, all drivers are installed except for a driver named "Android" which is too general for me to manual search (inlcuded an image attachment of the failed driver)
How can I unbrick my phone?
PLEASE HELP. THANK YOU IN ADVANCE.
same here..
same here my sky vega a760 stock on boot image anyone can help plsss how can i revive this..plsssss.
joekap said:
same here my sky vega a760 stock on boot image anyone can help plsss how can i revive this..plsssss.
Click to expand...
Click to collapse
You should re-install new room stook via home page iVeGa:good:
Re: Help..
tnx for the reply but how can i reinstall i dont know where to donwload and i cant understand in korean site.. plsss send me working rom for A760s plsss...tnx
[TUT]Recovery Mode Sky Vega Racer IM-A760S/A770K
joekap said:
tnx for the reply but how can i reinstall i dont know where to donwload and i cant understand in korean site.. plsss send me working rom for A760s plsss...tnx
Click to expand...
Click to collapse
To go into Soft/Ware download mode
1. Turn of phone
2. Simultaneously press: VOLUME UP + MENU + POWER
3. S/W Upgrading will now flash on the screen
To upgrade firmware back to version 1.47, you first need to have the UniUSBdriver installed on your computer.
4. After you have installed the driver, test your phone’s connection to the computer to initially determine all the required drivers were installed properly (this is while your phone is in S/W download mode). But before doing this, make sure that you have activated USB DEBUGGING on your phone.
Code:
>settings
>applications
>development
>usb debugging (must be checked)
5. Using Microsoft Internet Explorer v8 or v9, proceed to this page:
-------------->>> dmfile.isky.co.kr/NewSelfUpgrade/index.html?userid=&hpno
Notice when that page opens, it will prompt you to install ACTIVE X. Allow that installation to proceed.
6. After ACTIVE X has been installed, notice on the left side there is a something like loading prompt. Wait until it gets into blue bar with arrow up phrase noting USB with some Korean characters. Then boot to S/W mode your phone and plug it to your compurer then click the blue bar with arrow up.
7. Clicking the Blue bar with arrow up will turn it into a progressing bar. Notice the characters on top of the progress bar may change and at this point there is communication between the phone and the Sky download site. It may take a few minutes for the phone to establish a download connection between Sky’s services. Once a connection is established, the characters above the progress bar will turn into a progressing percentage bar starting from 1% and ending into 100%.
There will be two phases of the progressing percentage bar. The first phase is downloading the software while the second is loading the v1.47 software into the phone. After the 2nd phase, the phone will automatically reboot. The first phase will depend who slow or fast your internet connection is.
:fingers-crossed: Goodluck :fingers-crossed:
clearlangpo said:
To go into Soft/Ware download mode
1. Turn of phone
2. Simultaneously press: VOLUME UP + MENU + POWER
3. S/W Upgrading will now flash on the screen
To upgrade firmware back to version 1.47, you first need to have the UniUSBdriver installed on your computer.
4. After you have installed the driver, test your phone’s connection to the computer to initially determine all the required drivers were installed properly (this is while your phone is in S/W download mode). But before doing this, make sure that you have activated USB DEBUGGING on your phone.
Code:
>settings
>applications
>development
>usb debugging (must be checked)
5. Using Microsoft Internet Explorer v8 or v9, proceed to this page:
-------------->>> dmfile.isky.co.kr/NewSelfUpgrade/index.html?userid=&hpno
Notice when that page opens, it will prompt you to install ACTIVE X. Allow that installation to proceed.
6. After ACTIVE X has been installed, notice on the left side there is a something like loading prompt. Wait until it gets into blue bar with arrow up phrase noting USB with some Korean characters. Then boot to S/W mode your phone and plug it to your compurer then click the blue bar with arrow up.
7. Clicking the Blue bar with arrow up will turn it into a progressing bar. Notice the characters on top of the progress bar may change and at this point there is communication between the phone and the Sky download site. It may take a few minutes for the phone to establish a download connection between Sky’s services. Once a connection is established, the characters above the progress bar will turn into a progressing percentage bar starting from 1% and ending into 100%.
There will be two phases of the progressing percentage bar. The first phase is downloading the software while the second is loading the v1.47 software into the phone. After the 2nd phase, the phone will automatically reboot. The first phase will depend who slow or fast your internet connection is.
:fingers-crossed: Goodluck :fingers-crossed:
Click to expand...
Click to collapse
i need help. i just installed uniUSBdriver and it's successful. however, when i connect the phone there is one driver that is unable to install. the driver is just called "android" tried to look everywhere for a manual installer but the name of the driver is too vague to search. can you please help me with this one? it seems like the self upgrade site can't detect the phone without this driver installed.
Solution Soft brick, Android drivers in Fastboot
jimmygammi said:
i need help. i just installed uniUSBdriver and it's successful. however, when i connect the phone there is one driver that is unable to install. the driver is just called "android" tried to look everywhere for a manual installer but the name of the driver is too vague to search. can you please help me with this one? it seems like the self upgrade site can't detect the phone without this driver installed.
Click to expand...
Click to collapse
1. Connect your phone in Fastboot, and when your pc asks for 'Android' drivers, you need to install PDAnet, just google to download it.
2. then to Fastboot, and Install Recovery SWM v6 either normal or touch
3. Then go to Recovery and Install new stock/custom rom from SdCard.
thats all. :fingers-crossed:
bobby786pk said:
1. Connect your phone in Fastboot, and when your pc asks for 'Android' drivers, you need to install PDAnet, just google to download it.
2. then to Fastboot, and Install Recovery SWM v6 either normal or touch
3. Then go to Recovery and Install new stock/custom rom from SdCard.
thats all. :fingers-crossed:
Click to expand...
Click to collapse
can you post links where to get the recovery image and a link where to download roms? i'm trying to search but no luck. your help will be really appreciated. thank you very much :laugh:
stuck at s/w uploading
heeelp can anyone help me... my a760s dont turn on and if i plug a charger or into a pc the only thing that apears is "s/w uploading"
Did you fix it? results?
beakolang said:
heeelp can anyone help me... my a760s dont turn on and if i plug a charger or into a pc the only thing that apears is "s/w uploading"
Click to expand...
Click to collapse
Although its long enough for you to forget you once had Sky 760 but did you try the method posted by "clearlangpo"?
You phone reincarnated anyway?
clearlangpo said:
To go into Soft/Ware download mode
1. Turn of phone
2. Simultaneously press: VOLUME UP + MENU + POWER
3. S/W Upgrading will now flash on the screen
To upgrade firmware back to version 1.47, you first need to have the UniUSBdriver installed on your computer.
4. After you have installed the driver, test your phone’s connection to the computer to initially determine all the required drivers were installed properly (this is while your phone is in S/W download mode). But before doing this, make sure that you have activated USB DEBUGGING on your phone.
Code:
>settings
>applications
>development
>usb debugging (must be checked)
5. Using Microsoft Internet Explorer v8 or v9, proceed to this page:
-------------->>> dmfile.isky.co.kr/NewSelfUpgrade/index.html?userid=&hpno
Notice when that page opens, it will prompt you to install ACTIVE X. Allow that installation to proceed.
6. After ACTIVE X has been installed, notice on the left side there is a something like loading prompt. Wait until it gets into blue bar with arrow up phrase noting USB with some Korean characters. Then boot to S/W mode your phone and plug it to your compurer then click the blue bar with arrow up.
7. Clicking the Blue bar with arrow up will turn it into a progressing bar. Notice the characters on top of the progress bar may change and at this point there is communication between the phone and the Sky download site. It may take a few minutes for the phone to establish a download connection between Sky’s services. Once a connection is established, the characters above the progress bar will turn into a progressing percentage bar starting from 1% and ending into 100%.
There will be two phases of the progressing percentage bar. The first phase is downloading the software while the second is loading the v1.47 software into the phone. After the 2nd phase, the phone will automatically reboot. The first phase will depend who slow or fast your internet connection is.
:fingers-crossed: Goodluck :fingers-crossed:
Click to expand...
Click to collapse
Hello Hacker!
I am Zahid Gill and a software engineer by profession. Websites are my speciality. I love android and Korean phones. I have bricked/ unbricked fixed and patched many phone before (but only with XDA's help ) many
While flashing Sky vega 760s it stuck on some point. I waited long enough but thenI had to remove it and.... it was bricked.
I was still able to go to recovery, fastboot and bootloader. I tried wiping /system and others but cwm was not able to.
I tried flashing with offline flasher tool again but it went into red screen on bootloader, like here:
http://sphotos-g.ak.fbcdn.net/hphotos-ak-prn1/p206x206/26340_10200120329905648_1168156367_n.jpg
NOW, offline flashing stuck on 60%. I am unable to boot the phone in any other mode. Even putting on charging takes phone to this red s/w mode.
Are you able to help me with this? I shall be very thankful.
PS: I had stock ROM 4.1.2 originally updated with no custom tickling.
Did you find any solution
Hello I also stuck in same situation. My phone ima-760 got soft brick and red S/w upgrading only. Kindly help if any one has a solution.
Buddy
jimmygammi said:
my pantech sky vega a760s got soft bricked
here's what happened:
-the phone won't open unless connected to pc
-when connected, it will only go to charging mode
-when i try to enter recovery mode, this shows up:
"your phone will restart due to error occurred while running application "
i cannot access recovery mode, the only thing i can access is the s/w upgrade mode, which i don't know how to use since i'm not korean
and i can't understand pantech's website.
also, when i enter in fastboot mode, all drivers are installed except for a driver named "Android" which is too general for me to manual search (inlcuded an image attachment of the failed driver)
How can I unbrick my phone?
PLEASE HELP. THANK YOU IN ADVANCE.
Click to expand...
Click to collapse
I have the same problem but a lot of the answers are to re-install stock? Which part don't they understand...it's BRICKED ( and only shows the RED S/W Upgrading symbol) so it's impossible to Flash stock firmware in that state?
Hi!
I had a problem yesterday with my Amoi N828 cell phone. During a contact list or messages searching, my phone was automaticly restarted. My idea was to make a system restore using option available on the power on/off button. After that I saw chinesse menu which is not understoded for me I pressed some button and after that such process was started and stopped during 15 min. My decision was to a phone restart. And right now, during system initialization I'm seeing only Amoi logo and phone is stoped.
My next step was to flash system again. I found some drivers MT6589, additionally firmware and "SP flash tool"
When I'm connecting phone without battery by USB cable to the system (Win7 32 and 64 bit) is detected and looking the drivers. And now is a problem. my device is visible for the moment and after that is disappears and again - see link below:
youtube.com/watch?v=Wg47gdlB7YU
the question is why? When the drivers are installed, the problem is still same like before - nothing changed
PLEASE HELP ME! I'm woeful ((((
Hi All,
Have seen the numerous posts on this forum for the Lenovo P780, but cannot for the life of me get mine to work again
Model: P780 4GB (believe it is the Chinese version as when I first started it, Android was in Chinese (hence me trying to replace the ROM).
Here are the symptoms:
Black screen, won't power on, cannot even get into factory reset mode.
Tried the reset button on the back of the phone (some say 3-5 seconds others say 20 seconds - Tried both, nothing!).
Tried to fix the problem by doing the following:
Download the SP Flash Tools version 5.1352.01 and ran them on my Windows 7 Machine as Administrator.
Loaded the P780_ROW_S226_4GB_KIT_KAT (as this is what I thought would do the trick.)
Selected the MT6589_Android_scatter_emmc.txt file and then Firmware Upgrade set, then hit download, connected the phone to the laptop (red light on the phone), SP Flash Tool then goes to 100% Download DA (in red), and then the message "Unrecognized ROM detected".
That's it nothing else. Can't power on the phone.
Any advice help would be appreciated before I throw this phone through a window!!!
Thanks,
Mak.
makavelli12 said:
Hi All,
Have seen the numerous posts on this forum for the Lenovo P780, but cannot for the life of me get mine to work again
Model: P780 4GB (believe it is the Chinese version as when I first started it, Android was in Chinese (hence me trying to replace the ROM).
Here are the symptoms:
Black screen, won't power on, cannot even get into factory reset mode.
Tried the reset button on the back of the phone (some say 3-5 seconds others say 20 seconds - Tried both, nothing!).
Tried to fix the problem by doing the following:
Download the SP Flash Tools version 5.1352.01 and ran them on my Windows 7 Machine as Administrator.
Loaded the P780_ROW_S226_4GB_KIT_KAT (as this is what I thought would do the trick.)
Selected the MT6589_Android_scatter_emmc.txt file and then Firmware Upgrade set, then hit download, connected the phone to the laptop (red light on the phone), SP Flash Tool then goes to 100% Download DA (in red), and then the message "Unrecognized ROM detected".
That's it nothing else. Can't power on the phone.
Any advice help would be appreciated before I throw this phone through a window!!!
Thanks,
Mak.
Click to expand...
Click to collapse
Now step by step how to doit. This is the hard part for beginners:
1. download in your computer the drivers from here. Go to the bottom of the page.
2. install drivers
3. restart your computer (just to be sure).
4. now...with your phone allready powered off...
5. plug your USB cable in your computer
5.1 open the device manager...
6. plug your USB cable in your phone
7. new hardware detected should appear... and should install drivers automaticaly, if not grab fast the new thing appeared in device manager and install the seccond set of the drivers.
8. after the drivers are installed unplug your cable from the phone and restart your computer (just to be sure)
9. after restart of your computer download the ROM ,unzip to a known folder; skip this step if you have allready your firmware
10. now load scatter file from ROM directory(should be target_bin directory)
11. check DA,DL WITH CHECKSUM (NOT OPTIONAL) if you flash with SP Flash Tool v3, if you sflash with SP Flash Tool v5 skip this step.
12. press Firmware Upgrade button (NOT DOWNLOAD BUTTON) if you flash with SP Flash Tool v3, if you sflash with SP Flash Tool v5 select Firmware Upgrade and press Download Button
13. now just now plug usb cable to your phone.
14. firmware flash should start.(some red and other color lines should appear)
15. if the firmware is not starting remove the back case of your phone and hold pressed the little red button from the right side, for about 20 seconds then release. All this must be done with cable pluged in to your phone.
16. after flash is done a green circle should appear
18. disconect your phone and power on your phone
19. lenovo logo should appear. then you should be pacient because it will took some time before android boots for the first time.
20. Reboot at least once then your phone is ready to work HARD.
21. Good luck. Hope This Helps You.
stympy said:
Now step by step how to doit. This is the hard part for beginners:
1. download in your computer the drivers from here. Go to the bottom of the page.
2. install drivers
3. restart your computer (just to be sure).
4. now...with your phone allready powered off...
5. plug your USB cable in your computer
5.1 open the device manager...
6. plug your USB cable in your phone
7. new hardware detected should appear... and should install drivers automaticaly, if not grab fast the new thing appeared in device manager and install the seccond set of the drivers.
8. after the drivers are installed unplug your cable from the phone and restart your computer (just to be sure)
9. after restart of your computer download the ROM ,unzip to a known folder; skip this step if you have allready your firmware
10. now load scatter file from ROM directory(should be target_bin directory)
11. check DA,DL WITH CHECKSUM (NOT OPTIONAL) if you flash with SP Flash Tool v3, if you sflash with SP Flash Tool v5 skip this step.
12. press Firmware Upgrade button (NOT DOWNLOAD BUTTON) if you flash with SP Flash Tool v3, if you sflash with SP Flash Tool v5 select Firmware Upgrade and press Download Button
13. now just now plug usb cable to your phone.
14. firmware flash should start.(some red and other color lines should appear)
15. if the firmware is not starting remove the back case of your phone and hold pressed the little red button from the right side, for about 20 seconds then release. All this must be done with cable pluged in to your phone.
16. after flash is done a green circle should appear
18. disconect your phone and power on your phone
19. lenovo logo should appear. then you should be pacient because it will took some time before android boots for the first time.
20. Reboot at least once then your phone is ready to work HARD.
21. Good luck. Hope This Helps You.
Click to expand...
Click to collapse
Hi Stympy,
I have managed to get an Android ROM installed on the P780. Details are:
Android version 4.2.1
Build: P780_S136_140306
The only problem now is that the rear camera does not work, and have been told that trying to install a non-standard ROM could have blown the rear camera.
As I am not experienced with flashing these (or any other types of smartphones), I have no idea if this is correct.
Any advice would be appreciated.
Mak.
makavelli12 said:
Hi Stympy,
I have managed to get an Android ROM installed on the P780. Details are:
Android version 4.2.1
Build: P780_S136_140306
The only problem now is that the rear camera does not work, and have been told that trying to install a non-standard ROM could have blown the rear camera.
As I am not experienced with flashing these (or any other types of smartphones), I have no idea if this is correct.
Any advice would be appreciated.
Mak.
Click to expand...
Click to collapse
Look what i want you to do !
1. go here and download your firmware
2. go here and download this preloader.
3. replace the original preloader with the one from step 2.
4. reflash firmware and tell me what happent !
5. waiting for reply...
stympy said:
Look what i want you to do !
1. go here and download your firmware
2. go here and download this preloader.
3. replace the original preloader with the one from step 2.
4. reflash firmware and tell me what happent !
5. waiting for reply...
Click to expand...
Click to collapse
Hi Stympy,
Carried out the steps you listed, and I now get the message "Unrecognized ROM detected".
makavelli12 said:
Hi Stympy,
Carried out the steps you listed, and I now get the message "Unrecognized ROM detected".
Click to expand...
Click to collapse
Got to say a BIG thank you to Stympy who got my P780 back working again!!! A magician!!!!
Thanks again!:good:
This might be a long situp to write this, but i've experienced that a lot of the excelvan users do not really know, where to get support for their device. I've bought this device because the price was low. And so is the quality. It is assembled with a JTY mt10 smarphone mainboard, connected to a 10,1'' touch display.
I've bricked the device and getting help to retrieve it back to life was a pain. No support from excelvan, so I've experimented with it, to find the best possible solutions. In order to help you save time on rechearching this issue, I'll now post this, hoping it helps you getting the tablet back to life and running.
Notice: this is for excelvan mt 10 tablet only. I have no idea, if this works for any other product, so don't ask me, just look around the forum to find help. If the real hardware is bricked, this won't work either, your device should be repaired by qualified service persons to proceed with this.
1 setup your pc to get started.
I've installed the following software on my windows 10 desktop pc:
- The MTK Droid tools, links are supplied by this forum
- The MTK Sp Flash tool, you'll find links for that in this forum or get it from mediatek
- Philz recovery, use google to find it
- Kingo Root, you'll find it at the kingo root home page
- The Mediatek VCOM USB Drivers for Windows 10 (As for my PC) at Mediatek.
- The stock rom for excelvan mt10 tablet, you'll find it on needrom, download for registered users only
Installation of the software on your pc is straight forward, just follow the on-screen installation instructions and you'll be good to go.
Probably your device is bricked already, so no further action needs to be taken on your device.
The first thing you'll have to do is to see, if your drivers can connect to the device. To achieve this, follow the procedure below.
1. After setting up the drivers package, connect the device to your PC, using original USB cable. There are a lot of cables around there, but please use the original provided cable, as it is not sure, that other cables have all pins connected for this, so do yourself a favour...
2 Go to the device manager in your pc and look for your phone's name or the mediatek VCOM driver to run. If the device is booted up, you'll find them, if your device is bricked, you'll have to initiate the META mode of the 6572, to establish the connection. Luckily, the device has a reset button, so if it is bricked, you'll need to connect it to your PC, open up the device manager and press the reset button. (I've opened the device the very first time, to unsolder the battery leads, but I didn't know then, that there was a reset button...) The reset button is located between the micro USB and the Headset connectors on the right upper side of the device, the little hole there, use an insulated papar clamp to press it. In the device manager, you will see the driver popping up and after a short time, shut down. This is normal operation, sometimes it starts reconnecting over and over again, but that's allright.
3. First, you should try to get the preloader back on the system. This is very useful, many devices are bricked by shooting off the preloader. Open up SP Flash Tool, load the scatter file from the unzipped stock rom image for the device. You'll see the used blocks and partitions used by the software in the right pane of the flashtools program. Uncheck all blocks first, then click the checkbox at the 'Preloader', the first entry in the right pane..
4. Now connect your device with the USB cable to the pc. Yes, this comes first. Now press the 'Download' button, the dropdown bar should tell you 'Download Only'. If not, please select this from the dropdown and press download. Now the program waits for the connection, so press the reset button of your device. If all is setup correctly, your device will connect and download will start. First, you'll see a red bar running at the bottom part of the programs's screen, shortly followed by a yellow bar, showing progress of the download. If the download was successfull, you'll be notified accordingly. Disconnect your device and wait 10 seconds, then reconnect it to the pc. If your download was successfull, your phone will be recognised and stay connected, please look in your device manager on your pc, to see connection startup. You'll see the battery charging icon on your device, so it shows, that it is recovered back into it's life.
5. Now it comes to flash the rest of the firmware, so go back to SP Flash Tools, select the scatter file again, check all blocks EXCEPT the preloader and flash it to the device the same way, you've flashed the preloader. Now that you've selected more blocks to flash, you'll see that this takes much more time to download. So please be patient, do not tamper with anything, go ahead, get yourself a coffee or a beer and relax. If everything is okay, flashtools will inform you if the download of the firmware is successfull. If yes, you are good to go, for the first startup of your device.
Disconnect the device from your pc and power it on. If all is right, it will boot up android and you're ready to install and customize it for you.
But sometimes things just don't work this way, what can you do ?
Well, in my case, I've shot my preloader at the first try to flash the stock rom. Yes, I did not obey the rule that I should not tamper with this preloader, so it was checked also. This was a big mistake, after unsuccessfull download, the device did not react any more. The second time (I've bricked it again, because I would like to know, how to restore a bricked file system). So I've formatted all partitions, reinstalled everything and it worked fine. You can do this with the SP Flash Tools also.
I was tired of the 'Factory Recovery Mode', a standard piece of software, which seems to be some sort of rudimentary, so I'd like to install a CWM recovery for that. It would let me install a ZIP Update from the SD card, so it seems more usefull than that rudimentary factory recovery, but how to establish that ?
Searched the web for a long time. Used MTK Droid Tools for that, but this didn't work on the device. It could not create the recovery because of two errors:
- No found kernel GZ
- No found split boot image.
The search for the solution to these both errors resulted in just one thing: There seems not to be a solution for that.
If I can find the time, I will try to solve this but in this moment....
In this case, you'll have just one option left, install Philz Recovery. It brings touch capab8illity also, so it just seems ideal to have that. Besides the fact, that you can use the touch interface, the software brings a ton of usefull options with it, so it is the best choise for your device. I've extracted the ZIP file and dropped all items on my desktop to have a quick access to it.
This can only be done on a routed device, so you'll need to root it before continuing. Not rooting the tablet will result in hanging up the recovery program, so no use. I've rooted the device using kingo root. It runs on my pc and the only things installed on my device are the kingo root super user module and the kingo link module, for connectivity. The latter installations are done by kingo root and your PC, so you'll not have to do this yourself.
Rooting the device will take some time, so be patient. My device is connected as a JTY MT 10 Smartphone, when kingo root recognises it. It can take up to an hour to root. Probably there are other rooting programs out there, which could do the same, but I've tested a few of them, nothing else worked properly. I'll be using kingo root for this device in the future. Be aware, that the rooting with kingo root is session dependable, so after rebooting your device, you'll have to root it again.
You may now run the setup program for philz recovery. It can take more times starting up the program to successfully install the recovery on your device. I had to start the program 5 times, to get it installed completely, so if it is not working the first time, don't panic and start it over again.
The standard recovery image from the stock rom is not the same size as the recovery from philz. The program warns you for getting IMEI lost, so if you don't want this to happen, quit installation here. If you know what you do AND you have a backup of IMEI (NVRAM folders of the device) just go ahead. If installation of the recovery was successfull, you'll be notified by the program running on your pc. Now you can boot your device into recovery, by hitting the apropriate button presented by philz recovery setup program on your pc. To do this on the device itselft, power it off, wait 20 seconds, press the VOL + button and hold this while then pressing the power button. Hold these untill your screen lights up and select 'Recovery' from the menu, use VOL + for selecting, use VOL - to confirm. If the program starts, you'll notice, that it is 'Upside-Down'. That should not bother you, for this little inconvenience you get paid with a superb recovery.
In the next section of this post, I'll cover the backup and restore issues, using MTK Droid Tools, explain how to reinstall an IMEI, how to install a new MAC adress on the device. So stay tuned...
Joshi
Does anyone has custom recovery for Excelvan MT10?
Hi Guys,
I'm in a bit of a problem. I bricked my phone and nothing seem to help.
Let me tell whats happened
1. I updated my TWRP in LeTV X500
2. This kinda made my phone to in soft brick mode every time I restarted it went to TWRP
3. I than installed new ROM from TWRP (i think it might be too high for my phone)
4. Phone endup bricked, not switching on, off nothing - redl light only
5. I tried here to install new rom from Windows and Linux via SP Flash Tools - phone is not recognised.
6. I disassembled the phone and detached battery
- now this is actually helped in a way that windows now recognises the phone, but the connection is not continous
- it recognises MediaTek Pre launcher ... few seconds pass
- it disconnets the MT Pre Launcher
- It recognises VCOM USB Port ... few seconds pass
- It disconnets again
- loop like this goes on and on
7. I tried holding any of the buttons (up, down, power and combination) - not helping
8. I believe my last option is to try and bridge some of the points on the motherboard to try and reset the system ... is this correct?
I have no idea what should I bridge with what ... there are no labels on the MB, i'm not even sure where the GND is.
Any ideas fellas?
Here is front of the MB:
Code:
imgur.com/a/b4oWI
Here is back of MB
Code:
imgur.com/a/XgZiV
help will be appreciated
Have you found a solution?