[Q] Mobile Network State: Disconnect. Is It Hardware Problem? - Atrix 4G Q&A, Help & Troubleshooting

Operator: U Mobile (Malaysia)
Rom: 2.3.6(4.5.1.41.MB860.ATT.en.US) flash with CWM using fruit cake rom.
Baseband: N_01.77.36P
Kernal Version: 2.6.32.9 a21`[email protected] #2
Status: Can make call and receive sms. Apn setting is good. Wifi and bluetooth also work fine. Only mobile data state is the problem.
Problem:
1.I got this Atrix last 3 week. When i put a sim card it cannot detect my data so i install TWEAKKER from Play Store and get the setting for my APN. Everything work fine.
2. After a week i unlock the bootloader, install Nottachtrix, and again using TWEAKKER to set my APN, have fun with lapdock (overclock it using faux kernal to 1.45ghz). Everything still work fine.
3. Last 5 days i start play around with Titanium backup and supercharged v6. I backup and remove system application that i think i dont need it. I end up with mess around with the system but since i already made a backup i just restore it to default and then i start notice i lost my data signal.
4. I reflash fresh nottachtrix rom using CWM but the data still disconnected. I try flashing other rom like ICS rom also same problem. And then i flash official rom using CWM (fruit cake method) and RSD method. Still no luck. But today i play around with HiAPN and i can connect to data again but it seem not stable. But i can receive Phone call and sms without problem.
5. I already check my sim card by put it to other phone and i got no problem with it.
Any suggestion what i need to do to make data work again normally?
Update 18 May 2014:
1. I reflash 2.3.4 rom using RSD. Mobile Network State still disconnect. I will buy a new sim with different operator to test either my phone got problem or is it the sim/operator problem. Old but powerfull phone. I hope i got change to use it as daily phone again.
Update 21 May 2014:
Already test with other operator also no luck. Flashing all the radio that i found also no luck. Guessing the hardware got problem but quit confuse because call and sms still can receive.

miogy said:
Operator: U Mobile (Malaysia)
Rom: 2.3.6(4.5.1.41.MB860.ATT.en.US) flash with CWM using fruit cake rom.
Baseband: N_01.77.36P
Kernal Version: 2.6.32.9 a21`[email protected] #2
Problem:
1.I got this Atrix last 3 week. When i put a sim card it cannot detect my data so i install TWEAKKER from Play Store and get the setting for my APN. Everything work fine.
2. After a week i unlock the bootloader, install Nottachtrix, and again using TWEAKKER to set my APN, have fun with lapdock (overclock it using faux kernal to 1.45ghz). Everything still work fine.
3. Last 5 days i start play around with Titanium backup and supercharged v6. I backup and remove system application that i think i dont need it. I end up with mess around with the system but since i already made a backup i just restore it to default and then i start notice i lost my data signal.
4. I reflash fresh nottachtrix rom using CWM but the data still disconnected. I try flashing other rom like ICS rom also same problem. And then i flash official rom using CWM (fruit cake method). Still no luck. But today i play around with HiAPN and i can connect to data again but it seem not stable.
5. I already check my sim card by put it to other phone and i got no problem with it.
Any suggestion what i need to do to make data work again normally?
Click to expand...
Click to collapse
Not a smart advice, use it as last resource:
Find the radio version your phone have and flash it, or simply flash another radio. Be careful, tough as an incorrect version (not all radios work on every atrix) you may end with a nice hi-tech papeweight

andresrivas said:
Not a smart advice, use it as last resource:
Find the radio version your phone have and flash it, or simply flash another radio. Be careful, tough as an incorrect version (not all radios work on every atrix) you may end with a nice hi-tech papeweight
Click to expand...
Click to collapse
I already flash:
a) Radio N_01.77.30P
b) Radio N_01.77.36P
c) Radio N_01.77.37P_usa_att_12dec2011
d) Radio N_01.100.00R
I found all the radio in fruit cakes link except for D. Still no luck. Is it a problem with my phone? I can receive call and sms normally. Only data not work and i believe my APN setting is correct.

Already call my operator services and they also can't help. Today will try another sim card with different operator that i will borrow from my friend to check either i need to upgrade my sim or not.
Still hope to get any expert help from XDA forum

Any expert? I got iPhone and windows phone but nothing can beat this atrix+lapdock.

Atrix 4g connectivity
miogy said:
Any expert? I got iPhone and windows phone but nothing can beat this atrix+lapdock.
Click to expand...
Click to collapse
miogy said:
Already call my operator services and they also can't help. Today will try another sim card with different operator that i will borrow from my friend to check either i need to upgrade my sim or not.
Still hope to get any expert help from XDA forum
Click to expand...
Click to collapse
Hallo miogy,
this is a well known issue,
i am experience the same problem with my atrix 4G,
i recently flash the CM9 of CyanogenMod , (android 4.0.4),
before that i had the 2.3.4 (GB) - in this version my atrix had restart himshelf every day.
on the current version (CM9), i experiencig strange things with the Network.
this is not only us that experiencig that - it is a very common and wide .
its called RIL bug (RIL --> Radio Interface Layer),
my phone can work fine 2 or 5 ot 8 hours, and suddenly the data connection disconnected.
i even once had connected to a Mobile Carrier that is not mine.
as much as i understand till now, this RIL bug is caused of a bug in the Kernel, adn the best guys here in the XDA, are trying to solve it.
i am waiting to this solution very much, because this atrix 4g is great phone, and i like the CM9 also.
you can see for example this thread:
http://forum.xda-developers.com/showthread.php?t=2603032

Related

[Q] Cell radio wont turn on

Hi all
I dont know why / how but my cell radio suddenly went off and wont turn back on.
I am rooted BL unlocked on Nottachtrix 1.3.1 ROM.
I am also SIM unlocked and I live in India. I have the AT&T atrix.
What might have caused the issue
I was messing around in *#*#4636#*#* with the radio band.
I had this signal boosting app which I use but cant find it on the market to link it now. I 've been using this app for a while so dont know why it would mess up now.
I am not sure if these are what caused the issue but just letting u know
Things I have done so far
Battery pull
Different sim card / different network
I tried flashing the ROM again with full wipe but still no luck
Flashed CM7 Ba2tf and the problem persists.. can I rule out that it is software related?
Everything else is working fine.
I am out of ideas and help is very much appreciated.
Thanks
SOLUTION
The Easiest Fix for this issue is Flashing the right baseband in CWM recovery.
The radio is flashed separately from the Android os. Try a new baseband. However be sure to get the right one for your phone.
M
Sent from my MB860 using xda app-developers app
Issue solved. I 'll detail what I did so it can help others.
Yes. Selecting the USA Band is what caused the issue.
I dint know that basebands could be flashed on Atrix ROMs. I wish I 've known it sooner. Would 've saved me a lot of trouble. Anyway I went with the SBF method.
I had the 4.5.91 earlier but I went with 4.5.141 to be safe.
Everything went smooth but at the end RSD lite said "Please manually reboot this phone" and the phone went into a boot loop at the M logo. I looked around and after a while found that a Wipe fixes it in stock recovery.
1. Disconnected the phone
2. Pulled out the battery.
3. Rebooted and went into stock recovery.
4. Wiped data and rebooted.
5. Got to home screen fine. Rebooted once again to make sure everything is fine.
Then inserted sim card and I had a signal. Everthing is working great.
Bro i have solution.... Btw... You must have flashed the wrong rom.... Kindly download nd install other one ..or use custom cm14 ROM or miui for best experience..

[Q] ParanoidAndroid (and other) JB ROMs - Can't get mobile network to work

I can't post to the dev forum, so maybe someone over here can help:
I tried the PA ROM, because I really love the hybrid mode. The ROM has worked fine and looks great, but whatever version I flash, the mobile network, both data and phone, simply doesn't work.
It briefly connects to my provider (drei.at) and immediately disconnects, no matter whether I have data connection enabled or not.
Have tried this with all available versions of PA and did the usual routine: wipe, format system, wipe data. I even went totally back to a stock ROM, tried various modems, the current one being XXDLH9, which works just fine on [email protected] 0.6 ROM.
Had the same problem with Omega, FoxHound, and god knows what other ROMs I tried. No matter what, the only JB ROM actually working is [email protected] 0.6, that's it.
Is this a known phenomenon or have I overlooked something obvious?
The phone used to be a branded and simlocked Austrian T-Mobile, but ever since it has been debranded and SIM unlocked.
Any ideas?
All i can suggest is your apn settings?
Can try Offline SIM APN Database (get on Google Play) to insert the correct apn settings.
alchemist83 said:
All i can suggest is your apn settings?
Can try Offline SIM APN Database (get on Google Play) to insert the correct apn settings.
Click to expand...
Click to collapse
Thank you for the suggestion. The APN settings on a fresh install, all wiped, are correct and the same as in a working setup.
Any other ideas? Am I really the only one with that problem?
Modem tried APN correct .
Suggest next step is factory reset ..
Step after that is to install an official stock rom .
Others who may have a problem post in the roms thread .
jje
JJEgan said:
Modem tried APN correct .
Suggest next step is factory reset ..
Step after that is to install an official stock rom .
Others who may have a problem post in the roms thread .
jje
Click to expand...
Click to collapse
Did a factory reset, totally clean install with everything wiped.
Also, did a clean wipe and installed official stock ROM. Lost root, started from scratch and still didn't work.
I'd love to post in the ROM forums, but haven't yet posted my mandatory 10 postings.. Maybe this thread helps me to reach that limit
DF5JT said:
Did a factory reset, totally clean install with everything wiped.
Also, did a clean wipe and installed official stock ROM. Lost root, started from scratch and still didn't work.
I'd love to post in the ROM forums, but haven't yet posted my mandatory 10 postings.. Maybe this thread helps me to reach that limit
Click to expand...
Click to collapse
Possible hardware problem then .
jje
JJEgan said:
Possible hardware problem then .
jje
Click to expand...
Click to collapse
Very unlikely since it works on stock ROMs and [email protected] 0.6.
Uhm you just said that it still did not work on Stock?
What error message does the deviche present in *#4636#* -> phone info under Gprs?
Sent from my GT-I9300 using xda premium
d4fseeker said:
Uhm you just said that it still did not work on Stock?
What error message does the deviche present in *#4636#* -> phone info under Gprs?
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
No, that's not what I said. Stock ROMs work just fine; I actually just flashed the latest leak (DLI5) and had no problems with the network. The problem hasn't changed, so it's what I wrote in the OP: Only JB to work ist latest leak and [email protected] 0.6. All others can be installed but have not network connection other than WiFi.
DF5JT said:
I can't post to the dev forum, so maybe someone over here can help:
I tried the PA ROM, because I really love the hybrid mode. The ROM has worked fine and looks great, but whatever version I flash, the mobile network, both data and phone, simply doesn't work.
It briefly connects to my provider (drei.at) and immediately disconnects, no matter whether I have data connection enabled or not.
Have tried this with all available versions of PA and did the usual routine: wipe, format system, wipe data. I even went totally back to a stock ROM, tried various modems, the current one being XXDLH9, which works just fine on [email protected] 0.6 ROM.
Had the same problem with Omega, FoxHound, and god knows what other ROMs I tried. No matter what, the only JB ROM actually working is [email protected] 0.6, that's it.
Is this a known phenomenon or have I overlooked something obvious?
The phone used to be a branded and simlocked Austrian T-Mobile, but ever since it has been debranded and SIM unlocked.
Any ideas?
Click to expand...
Click to collapse
Have you tried flashing a new baseband? i had the same problem, when flashing the franco. Kernel..
or, go back stock, then reflash the desired ROM
EDIT: If it helps, I speak/write fluent german ('Cause I live in germany ^^)
familyguy59 said:
Have you tried flashing a new baseband? i had the same problem, when flashing the franco. Kernel..
or, go back stock, then reflash the desired ROM
Click to expand...
Click to collapse
Thanks for trying to help.
Yes, I have been playing around with all kinds of basebands, trying to flash modems etc. but that does not seem to be the reason for it. I have had different modems working and the very same modems simply did not work with PA at all. Best example ist yesterday's leak DLI5 which I flashed and had a virgin like system working just fine with my network. I then flashed the PA ROM, which then had the same baseband as the latest stock ROM, but, alas, same story: No network.
The weird thing is the brief connect it always shows in the status bar. It lasts roughly 4-5 seconds and then disconnects again, only showing the empty network status display.
It really sucks, because I find the idea of hybrid ROMs really appealing, in fact, this seems to me as a truly superior way of making use of the 720p display.
Need to try logcat next to see whether the connect/disconnect somehow can be monitored from there. Will report on that.
DF5JT said:
I can't post to the dev forum, so maybe someone over here can help:
I tried the PA ROM, because I really love the hybrid mode. The ROM has worked fine and looks great, but whatever version I flash, the mobile network, both data and phone, simply doesn't work.
It briefly connects to my provider (drei.at) and immediately disconnects, no matter whether I have data connection enabled or not.
Have tried this with all available versions of PA and did the usual routine: wipe, format system, wipe data. I even went totally back to a stock ROM, tried various modems, the current one being XXDLH9, which works just fine on [email protected] 0.6 ROM.
Had the same problem with Omega, FoxHound, and god knows what other ROMs I tried. No matter what, the only JB ROM actually working is [email protected] 0.6, that's it.
Is this a known phenomenon or have I overlooked something obvious?
The phone used to be a branded and simlocked Austrian T-Mobile, but ever since it has been debranded and SIM unlocked.
Any ideas?
Click to expand...
Click to collapse
Bump.
Nearly the same prob to me! I loose data if I change my location, also provider "3" in Austria! Stock is working, CM10 nightly also. I tried different Modems tomorrow the ODIN Leak.
Andi
me too
no data network after flash on two diffrent galaxy s2's
kaos7 said:
no data network after flash on two diffrent galaxy s2's
Click to expand...
Click to collapse
I was having the same issue, I pulled the SIM and wiped it down, blew off the contactors, seems to of solved the problem for the time being.
WiFi works, Mobile Networks do not
2Fast 2Low Customs said:
I was having the same issue, I pulled the SIM and wiped it down, blew off the contactors, seems to of solved the problem for the time being.
Click to expand...
Click to collapse
I just installed ParanoidAndroid. I'm kind of a noob to all of this.
I understand some, but not all.
My mobile networks are not working.
I don't get any notification at the top of the screen either saying I'm on a mobile network.
I've messed around with the APN settings. It seems that every now and then it'll connect for a brief moment, but I can't really do anything unless I'm connected to WiFi.
Any help would be appreciated.
I came from a stock phone rooted.
Installed this and now I'm here.
Please HELP!!
Had this problem with stock roms..
The network is fine but doesn't exchange data correctly.. AOSP worked fine for me.. PA= flawless
BHARGAV33 said:
Had this problem with stock roms..
The network is fine but doesn't exchange data correctly.. AOSP worked fine for me.. PA= flawless
Click to expand...
Click to collapse
Turns out I just had crappy reception at home.
I wanted to get 3+ but something got in the way and had to go with the 2.+
Sorry for not understanding, but what is AOSP? I see that, but I don't get what is what.
ASOP = Android Open Source Project.. They are best but not that much good at battery
Spend some time on xda and Google your doubts.. You'll surely understand everything from android

[Q] Lost automatic connection with my data plan

Hi everybody!
Yesterday, I applied a custom rom to my Galaxy Note and after a successful installation, my data plan wasn't working like it used to be.
I have to say this isn't the first time I have done this, and in the previous opportunities after flashing the rom and rebooting, the EDGE/3G icon appeared by itself detecting my data plan. I never had to configure the APN settings (like it is said in many posts I have seen here).
So, when I realize that it wasn't working properly, I re-flashed the rom but didn't worked. So then, I downloaded the ICS stock rom and flashed it through Odin, hoping it would reset all things here and would give me the initial configuration, but that didn't work either.
I have entered through settings and deactivated/activated the options related to mobile data, but that icon never appears or my data connection showed up.
Forgot to mention that this phone was unlocked through cellunlocker by code, and that I can make phone calls with no problem and also the Wifi works fine... And thank you in advance for any advice/help that you could make
If it's happening with different ROMs then take a look at your modem (baseband). Are you using I717UCLF6? Go to System Settings-About Phone-Baseband Version.
Like ^^^^ said, and you didn't say it, but I'm guessing T-Mobile. So flash any ROM you like, reboot and let but settle in, then flash the Blaze 4G or whatever T-Mobile modem works best for you.
You did enter your APN info?
Agoattamer said:
You did enter your APN info?
Click to expand...
Click to collapse
This....^^^^^^^^^^^^^^^^^^^^^^^^^^^................g

Need help please!

Hi everyone. I'm having some serious (or at least I think so) problems with my I777. I live in Colombia, and I bought it over two years ago, had it shipped over by a friend, unlocked. Up until today I'd been using it normally, without any major problems.
However, the last couple of days it started behaving strangely, (turning itself off every once in a while, losing data, etc), so I decided to update my rom today.
I tried to install a new CyanogenMod 4.4 from this site, but I got some kind of status 7 error and it didn't behave properly after that.
Next thing I did to try to fix it was flash a stock JB 4.1.2 rom via Odin.
It worked, but that's when the major problem struck... Apparently my phone got locked for AT&T again or something. It's not recognizing my sim-card anymore. It shows the "no-sim" notification on the top bar, yet it also shows it has a signal (no data, just phone signal), even when my sim-card isn't inserted. When I go in the settings to try to access the mobile networks it says insert sim card even when it's in there.
I did a lot of searching and I used GalaxSimUnlock, which I got from this site too, and it confirms my phone is unlocked.
So basically... What the heck happened?? Is it possible that after three years of using it perfectly with my Colombian sim, the AT&T lock just "came back" or something after flashing a stock rom?
Any clue guys?
If you used galaxsimunlock the unlock is permanent.
Sent from my SGH-I777 using XDA Free mobile app
After you flashed back to stock, did you try to root again and flash another custom ROM?
I could be wrong on this, but the AT&T stock firmware may not be giving you the choice to register the SIM or change the APN settings for you particular network. I can't confirm this though as I never flash to stock long enough to actually use it. I always root and go back to something else immediately afterwards.
The only suggestion I have is to go back to a custom ROM and try again.
If you are trying to go to KitKat, be sure you have the newest compatible recovery (CWM or TWRP) as the versions of those that work with JB will not allow you to flash a KitKat ROM. There are plenty of threads that will tell you what versions you need. If it's an SGH-i777 model then all you should need to get the proper recovery is to flash one of the two KK compatible kernels as the recovery is packaged with them.
Good luck!

[Q] Galaxy SII: Error While Searching for network- On all custom roms

hey guys!
I have samsung galaxy s2 gt-I9100. Whenever I install a custom rom, everythings works fine but i am not able to use mobile network and i received "Error while searching for networks" when I go to settings>>Mobile networks>>network operators. The IMIE number is fine.
I have tried many roms including:
--cm-10.1.3-i9100
--cm-11-20140804-SNAPSHOT-M9-i9100
--pa_i9100-4.42-20140708
--pa_i9100-4.45-20140729
--Slim-i9100-4.4.4.build.9.0-OFFICIAL-8301
The last rom which worked fine was RootBox-JB-i9100-V4.0. All roms released after this rom have this issue.
I have searched for issue on google and tried various solutions but so far no success.
Please Help!
And can you guys suggest me any rom which is not based on CM?
Go to settings-->about phone and look for "Baseband version"
If it says "unknown" or similar you may need to reflash the modem before you flash the rom.
Or even worse you might need to do a reboot (it actually worked once).
Also do emergency calls work? If yes then it might be a problem with your sim card or you contract (or just bad luck).
ruleh said:
Go to settings-->about phone and look for "Baseband version"
If it says "unknown" or similar you may need to reflash the modem before you flash the rom.
Or even worse you might need to do a reboot (it actually worked once).
Also do emergency calls work? If yes then it might be a problem with your sim card or you contract (or just bad luck).
Click to expand...
Click to collapse
The Baseband version is visible and a valid one. Also my sim works on stock rom or any other phone.
SInce I have no idea what the cause could be, here are some random things to try out, of which one might work:
-make sure you're not in airplane mode
-do a full complete wipe
-try a different sim (and see if it works)
-make sure the sim is not upside down
-fully shutdown the phone (e.g remove battery for a day [maybe not that long])
-clean contacts between sim and phone (how? no idea)
-try (even-) more roms (if there are any left)
-test a few kernels
-maybe look through the logcat (if it actaully outputs something worthwhile)
As you can see none of these "soloutions" are based on.....uhmm....anything(?). But at least....if none of them work, you know what not to do.
faizi97 said:
The Baseband version is visible and a valid one. Also my sim works on stock rom or any other phone.
Click to expand...
Click to collapse
Perhaps you could flash back to stock rom then flash custom rom again, that way all modem files and network related files can be fixed/re-installed. By any chance have you tried changing modems? It might not help you but it's a suggestion.

Categories

Resources