Hi Guys, I've been going through these forums for days and have tried so many things, but I still can't un-brick this phone, I'm pretty sure its a soft brick, because I can still get into download mode, but if I try to start the phone normally, I just get a white screen now when I enter download mode, it says "downloading do not turn off target" now when I plug it into the pc, odin sees it ok, but I have tried uploading new stock firmware, its my friends phone, and as far as I know its not rooted, now when I tried flashing a new stock firmware, it failed becase of something to do with the partition, so I read through these forums and found a thread about uploading a new pit file, which I did, and that failed as well, so I need hepl please guys, how screwed is this phone?? its an international Galaxy S3 i9300 on O2
first of all, how did u brick it lol
Enviado desde mi GT-I9300 mediante Tapatalk
What pit file and what stock firmware are you trying to flash?
Sent from my HTC One using Tapatalk
Go try the rescue firmware (search in general forum) but probable that the emmc is corrupt/damaged. If the rescue firmware won't flash then you'll need a new motherboard.
Sent from my GT-I9300 using Tapatalk
right, Blackstard, its my friends phone, and something happened while it was doing a firmware update, not sure what, eith got turned off just got stuck I think, she was probably to impatient to let it finish
Mrao, GT-I9300_mx_20120329 pit file and I9300XXUGND3_I9300H3GGND1_I9300NEUGND1_HOME.tar from sam mobile pit file was from in here I think
Right Boomboomer, I have tried the recovery firmwares, there were two of them and I tried them both, but it just fails at the pit file and says it cant format the partition, is this the end? or is there anything else I can try?
This is what comes up in Odin
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_I9300OXAEMG4_KOR_FACTORY_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005>
<ID:0/005> Re-Partition operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Sounds like the emmc chip is damaged.
If you can get a z3x box there is a thread which describes how to resurrect a corrupt chip:
http://forum.xda-developers.com/galaxy-s3/general/epairsamsung-s3-i9300-note2-n7100-dead-t2647558
But even that won't help a dead emmc chip.
Related
Hey People, I am new here and and I am a complete Noob with my phone, I bought it on ebay and it came with a strange version Hydr0gen! I was not able to install any app, only a few... but not like Facebook, Waze Gmail and many more... for many months I was frustrated because of this and today my phone started acting strange. I connected it to KIES and it wont reconize it so I tried ODIN, donwloaded the original IS firmware, run it and it gaves my an error message. I run again nothing happen and turn it off... then when I turn the phone again I get Firmware upgrade encountered and issue. Please select Recovery mode in KIES & try again. I do connect it to Kies but still it wont reconize it, I tried everyhting with odin but nothing yet... I only get FAIL!
Someone please help! I dont have any phone and I need it as soon as possible.
Here is what I get!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100_APBOOT_I9100XXLPH_CL118559_REV02_user_low_sh ip.tar.md5 is valid.
<OSM> I9100_CODE_I9100XXLPH_CL118559_REV02_user_low_ship .tar.md5 is valid.
<OSM> MODEM_I9100XXLPH_REV_02_CL1104396.tar.md5 is valid.
<OSM> GT-I9100-MULTI-CSC-OXALPH.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can you enter download mode?
Sent from my Galaxy S2 GT i9100
If you enter in the download mode, re-upload a rom with 3 files
marnaqui said:
Hey People, I am new here and and I am a complete Noob with my phone, I bought it on ebay and it came with a strange version Hydr0gen! I was not able to install any app, only a few... but not like Facebook, Waze Gmail and many more... for many months I was frustrated because of this and today my phone started acting strange. I connected it to KIES and it wont reconize it so I tried ODIN, donwloaded the original IS firmware, run it and it gaves my an error message. I run again nothing happen and turn it off... then when I turn the phone again I get Firmware upgrade encountered and issue. Please select Recovery mode in KIES & try again. I do connect it to Kies but still it wont reconize it, I tried everyhting with odin but nothing yet... I only get FAIL!
Someone please help! I dont have any phone and I need it as soon as possible.
Here is what I get!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100_APBOOT_I9100XXLPH_CL118559_REV02_user_low_sh ip.tar.md5 is valid.
<OSM> I9100_CODE_I9100XXLPH_CL118559_REV02_user_low_ship .tar.md5 is valid.
<OSM> MODEM_I9100XXLPH_REV_02_CL1104396.tar.md5 is valid.
<OSM> GT-I9100-MULTI-CSC-OXALPH.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
well, okay first of all.. i think your phone is ROOTED that's why you cannot receive any firmware updates and you cannot connect to Kies.
so what you need to do is to download a firmware over at sammobile.com and then unzip the file, you will then get a .tar file.. you then use odin. connect your phone while it is on download mode and check if odin recognizes your phone. in PDA, click on the .tar that you had from the extraction then click on start.
your flash via odin may be a result from an incomplete download.
cheers
saywhatt said:
well, okay first of all.. i think your phone is ROOTED that's why you cannot receive any firmware updates and you cannot connect to Kies.
so what you need to do is to download a firmware over at sammobile.com and then unzip the file, you will then get a .tar file.. you then use odin. connect your phone while it is on download mode and check if odin recognizes your phone. in PDA, click on the .tar that you had from the extraction then click on start.
your flash via odin may be a result from an incomplete download.
cheers
Click to expand...
Click to collapse
Hey Guys thanks for the reply... I am not sure what firmware to donwload... I am located in latin america Costa Rica, Carrier ICE... I just need an unlocked phone. I am able to get in to Download. And I also try to download the original stock firmware but when I put it in PDA I get an FAIL. I am not sure if its the correct firmware... can Someone please help me with that I really appreciate all of the help! Really!
Also when I go to Kievs and type update the firwmare I put the serial number and the model and I accept the agreement and then I get a pop message, saying something in Japan or chinese I dont know what it says but I soon as I click ok... it closes the update
Bump!
On connecting your phone to KIES, does it install the phone drivers?
Also, ensure you're installing a firmware for your own device. ie. not installing i9100G firmware on an international i9100 /P/M/T. or vice versa.
Next make sure your phone has adequate charge before going into download mode. Even if its soft-bricked, it will still charge.
Also, connect your phone to a USB port directly on the computer. Not via a hub or a USB port on your keyboard or something.
Sent from my GT-I9100 using xda app-developers app
marnaqui said:
Hey Guys thanks for the reply... I am not sure what firmware to donwload... I am located in latin america Costa Rica, Carrier ICE... I just need an unlocked phone. I am able to get in to Download. And I also try to download the original stock firmware but when I put it in PDA I get an FAIL. I am not sure if its the correct firmware... can Someone please help me with that I really appreciate all of the help! Really!
Click to expand...
Click to collapse
If u want to use Odin than uninstall kies is a must as its tsr program will interrupt Odin processes. U just need to download correct & match firmware from samsung-updates.com or sammobile.com, then repeat the flashing but just use Odin v1.85 as its most compatible w/ s2. Don't tick anything else from Odin before click start button except auto reboot, one packages & PDA section (browse ur firmware file). & Odin doesn't care if ur phone rooted or unrooted. It will does a full wipe if u flash a f/w by Odin, so rooted phone will lost its root.
Sent from my GT-I9100 using xda app-developers app
If all else fails follow this guide EXACTLY. Check make and model on sticker under the battery. All the best. http://forum.xda-developers.com/showthread.php?t=1457458
Sent from my GT-I9100 using xda premium
I was using the MIUI rom and I sold the phone. To deliver to the buyer I decided to go back to the stock rom but forgot to wipe and now I have the following situation:
- I can only get into download mode
- Odin recognizes the phone
- I tried to repartition the Odin reported successful operation (my model is 16gb)
- Tried to put other roms on the phone including those downloaded from the site sammobile, selecting only auto-reboot and f.reset.time
- With these steps could only get stuck in "nand write start ..."
- Tried installing kies but do not believe it can be something with the drivers because the odin recognizes the phone.
I read many posts but after two days decedi post to see if anyone would help me solve this issue
I'll be waiting for directions on how to proceed without worsening the scenario.
Odin log:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBBLG2_I9300VILG1_I9300ZVVBLG1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> modem.bin
<ID:0/006> NAND Write Start!!
have you tried restarting your computer or using another computer? or even a different usb port or cable?
ages ago I had a similar problem - never moved beyond the start point - simple restart solved it for me...no idea if that's the same situation as you.
Just throwing out ideas here; otherwise I'm not sure.
Sent from my GT-I9300 using Tapatalk 2
Tried to do this, but still stucked at nand write start...
One thing I noticed is that the progress bar on the phone at the "downloading mode screen" runs quickly, and then it stops at nand write start.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBBLG2_I9300VILG1_I9300ZVVBLG1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> modem.bin
<ID:0/005> NAND Write Start!!
At least I'm not alone
I have the exact same problem you have. Intl i9300, cannot enter recovery, only download mode. Flashing 16gb pit file works ok, however attempting to flash Stock rom gets stuck at Nand Write Start. Not sure what to do now, I guess I'll wait for responses here as well.
RePartition .
Fail Nand write .
Assuming you have read and are following the basics re an Odin flash ( if not go and read them ) .
This sounds in both cases like a damaged Nand >>> service centre job .
jje
I've not done much to my S3. Trouble started when I decided to install an OTA of Foxhound 1.8. Installation completed successfully but during the application upgrade (...you know the first boot message of 'Android is updating x of 365 apps). It froze and stuck there for like 15min so I decided to reboot it and all hell broke loose.
Started with 'Foxhound cannot mount recovery command..' etc. Which made me decide to flash my 16gb pit file, and since then all attempts to flash back to stock stall at 'Nand write start'.
I have backups of everything, even my efs. Problem is I can't even get to recovery to restore anything.
I'll keep trying I guess, worst case I'll just return it back to Samsung.
pull usb devices except s3 and be sure to have correct drivers then try again. you may even try it on another pc of course with installing drivers. if none of them works try flashing a kernel or recovery if it flashes then try to flash stock rom.if stucks again at nand write there may be a problem at emmc sect. but dont worry just do what i said if it fails there should be a solution
if you can enter the recovery mode u should be happy
to kamau can u send me the pit file you flashed thanks
zhjackss said:
to kamau can u send me the pit file you flashed thanks
Click to expand...
Click to collapse
There it is. I"m now working on resetting the flash counter from odin since I obviously can't install triangle away in preparation of returning it to samsung.
Hello everyone,
I know this is not a new question/topic but I've searced too much and couldn't find the working solution.. ): There are too much posts too much answers over google and i tried most of them but they didn't work for me.. I just need simple and short anwers like all of you. Thanks!
I am using Cyanogenmod 10.2-20131102-SNAPSHOT-M1-i9300 on my SGS3 I9300 (intl) and my device had about 500 mb free space. I was on facebook and suddenly my phone restarted and freezed at the samsung boot logo.. ): I can't reach recovery mod.. TWRP boot screen is freezing.. I can only reach download mode.
I have searched on google a lot of forums. I tried to turn back stock rom with odin on different versions but it always gave failed answers. I also tried recover with kies and another kies installed computer but it didn't create any solution..
I tried soft reset, hard reset, "pit" things but they didn't help me..
I tried "GT-I9300XXUGMJ9_KOR_FACTORY" and odin said "Re-Partition operation failed."
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXUGMJ9_1902166_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9300XXUGMJ9_1902166_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXUGMJ9_1902166_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_I9300OXAGMJ9_1902166_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006>
<ID:0/006> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Another try with odin ended with "can't open the serial(com) port"
Finally, I tried and read too much things with/without kies computers.. ):
I just don't know what and how is cyanogenmod SDS fix.. and maybe I missed something like sds or heimdall or another thing that I've never heard before.. I couldn't find any solution yet..
I think the last thing to do, taking my phone to the service and replace the motherboard.. But I've bought this phone from Hong Kong when I was in Turkey on August 2012. Now I'm living in Italy and I think I don't have any warranty.. ):
Anyway, but i believe that there should be a solutoin by myself. Do you know it?
Thanks for help, sorry for my english mistakes. See you soon.
ozgurhunkur said:
Hello everyone,
I know this is not a new question/topic but I've searced too much and couldn't find the working solution.. ): There are too much posts too much answers over google and i tried most of them but they didn't work for me.. I just need simple and short anwers like all of you. Thanks!
I am using Cyanogenmod 10.2-20131102-SNAPSHOT-M1-i9300 on my SGS3 I9300 (intl) and my device had about 500 mb free space. I was on facebook and suddenly my phone restarted and freezed at the samsung boot logo.. ): I can't reach recovery mod.. TWRP boot screen is freezing.. I can only reach download mode.
I have searched on google a lot of forums. I tried to turn back stock rom with odin on different versions but it always gave failed answers. I also tried recover with kies and another kies installed computer but it didn't create any solution..
I tried soft reset, hard reset, "pit" things but they didn't help me..
I tried "GT-I9300XXUGMJ9_KOR_FACTORY" and odin said "Re-Partition operation failed."
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXUGMJ9_1902166_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9300XXUGMJ9_1902166_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXUGMJ9_1902166_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_I9300OXAGMJ9_1902166_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006>
<ID:0/006> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Another try with odin ended with "can't open the serial(com) port"
Finally, I tried and read too much things with/without kies computers.. ):
I just don't know what and how is cyanogenmod SDS fix.. and maybe I missed something like sds or heimdall or another thing that I've never heard before.. I couldn't find any solution yet..
I think the last thing to do, taking my phone to the service and replace the motherboard.. But I've bought this phone from Hong Kong when I was in Turkey on August 2012. Now I'm living in Italy and I think I don't have any warranty.. ):
Anyway, but i believe that there should be a solutoin by myself. Do you know it?
Thanks for help, sorry for my english mistakes. See you soon.
Click to expand...
Click to collapse
You won't get any solution/answer by yourself. its an SDS and no other options else than taking it to service center..
suyash1629 said:
You won't get any solution/answer by yourself. its an SDS and no other options else than taking it to service center..
Click to expand...
Click to collapse
Thank you for reply. Do you know is it (SDS) in warranty or not? Because I saw that clean/stock/unrooted devices had the same problem..
SDS is covered by warranty .
But warranty is void with root and custom roms or indicators of such .
Likewise warranty is not worldwide so it looks like you buy a new motherboard or pay for a service repair .
Its all in the faqs and guides .
Title says it all.
I tried to boot into recovery menu to look at something but that failed. I connected my GS II to odin re install the firmware but odin stalled. I had to kill odin with Task manager. Before odin, my phone would go to the download recovery menu. Now I cannot get it to respond at all.
Did odin not responding and me killing odin via TM hard brick my phone?
lol. A Courts-Martial started today for an old neighbor of mine and I was supposed to testify but they never called me (until my phone broke). My company commander tried to call me but couldn't get me. He called my NCOIC so my NCOIC tried to call me. Nope. NCOIC called one of the guys near me and told him to see if I was still alive.
lol.
Odin failing to complete the flash would not usually hard brick the phone. Usually after a failed flash, you can still get into download mode and flash again. If the flash was interrupted while Odin was loading the boot loader, then you would get a hard brick, but the boot loader goes on in in a matter of seconds, so the exposure is small.
Don't know what would cause the phone to be completely unresponsive, but if you can't get it into download mode, then your options are limited. You could send it out for jtag repair but that would probably cost around $50 to $60. If you decide to go that route, Mobile Tech Videos is a trusted and respected shop.
Wife's phone is done, at least I am done with it. She can pick from a GS3 mini or GS4 mini. I bricked mine while working on hers.
Mine is off to mobile tech videos. I should get it back next week. Wife gets a new phone, I will keep my SII.
svtfast said:
Wife's phone is done, at least I am done with it. She can pick from a GS3 mini or GS4 mini. I bricked mine while working on hers.
Mine is off to mobile tech videos. I should get it back next week. Wife gets a new phone, I will keep my SII.
Click to expand...
Click to collapse
The SIII mini is still lower-end than the S2. :b
Stuck as well
I keep trying to flash CWM recovery tar file with Odin because I cant seem to get passed the start up logo with the big S in the middle and I keep getting this issue:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ODINRecovery.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
If anyone could help or if anyone could point to someone that could help me I will be forever in you debt.
It was bricked. Send it to mobiletechvidoes and got it back. Working like new!
Rooted and CWM installed. ShoStock rom installed but ended up in bootloop. Reinstalling now.
d27redux said:
I keep trying to flash CWM recovery tar file with Odin because I cant seem to get passed the start up logo with the big S in the middle and I keep getting this issue:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ODINRecovery.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
If anyone could help or if anyone could point to someone that could help me I will be forever in you debt.
Click to expand...
Click to collapse
Why did you post in this thread? You should start your own thread for a new issue.
Do you have SGH-I777, or is it SGH-S959G, or some other model? If I777, you can't flash a separate recovery. Recovery is built in to the kernel, so you have to flash a kernel to get CWM.
Please study and know what you are doing before you damage your phone.
Hi everyone,
My head is spinning from what's just happened. My phone mysteriously decided to crash on me after being a little slow and unresponsive recently. I'm running CM11 M5 on my phone, I found this is the most stable of the roms for me. The unusual thing about this crash was that it rebooted with a fuzzy, static-like screen, so I tried to reboot into the Cyanogen bootloader thingy and it just brings up the crash screen. I tried to reboot into Odin Mode, hooked up the phone to my computer and tried to reinstall a new ROM. First I tried with Odin 3.07 with a ROM I loaded onto it last month (I9300XXUGNA5_I9300AUTGNA1_I9300XXUGMK6_HOME.tar.md5), but the Odin program on the computer crashes each time. I also tried with an updated version of Odin, v1.85 and also Odin Auto. I had an issue last month, looked around and fixed it by downloading this ROM just mentioned, but this time, no joy. I've tried with another that I just downloaded (root66_TMO_T999UVDLJA.tar.md5) and the same thing happens. At one point, I received a message on different attempts where the Odin program would spit back at me this:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_TMO_T999UVDLJA.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1
So, how do I proceed from this point? I don't know enough to understand what the problem is with this, maybe something to do with the PIT mapping? I feel like I've covered every possible avenue that I can see posted online, I'm really not sure if there is anyone else with this problem, where the Odin program is so volatile. Your thoughts would be greatly appreciated, I suffer without my phone.
Stuart
blackbeardtwenty said:
Hi everyone,
My head is spinning from what's just happened. My phone mysteriously decided to crash on me after being a little slow and unresponsive recently. I'm running CM11 M5 on my phone, I found this is the most stable of the roms for me. The unusual thing about this crash was that it rebooted with a fuzzy, static-like screen, so I tried to reboot into the Cyanogen bootloader thingy and it just brings up the crash screen. I tried to reboot into Odin Mode, hooked up the phone to my computer and tried to reinstall a new ROM. First I tried with Odin 3.07 with a ROM I loaded onto it last month (I9300XXUGNA5_I9300AUTGNA1_I9300XXUGMK6_HOME.tar.md5), but the Odin program on the computer crashes each time. I also tried with an updated version of Odin, v1.85 and also Odin Auto. I had an issue last month, looked around and fixed it by downloading this ROM just mentioned, but this time, no joy. I've tried with another that I just downloaded (root66_TMO_T999UVDLJA.tar.md5) and the same thing happens. At one point, I received a message on different attempts where the Odin program would spit back at me this:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_TMO_T999UVDLJA.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1
So, how do I proceed from this point? I don't know enough to understand what the problem is with this, maybe something to do with the PIT mapping? I feel like I've covered every possible avenue that I can see posted online, I'm really not sure if there is anyone else with this problem, where the Odin program is so volatile. Your thoughts would be greatly appreciated, I suffer without my phone.
Stuart
Click to expand...
Click to collapse
Use this if it fails it needs service repair >> http://forum.xda-developers.com/showpost.php?p=30087735&postcount=6 <<
blackbeardtwenty said:
Hi everyone,
My head is spinning from what's just happened. My phone mysteriously decided to crash on me after being a little slow and unresponsive recently. I'm running CM11 M5 on my phone, I found this is the most stable of the roms for me. The unusual thing about this crash was that it rebooted with a fuzzy, static-like screen, so I tried to reboot into the Cyanogen bootloader thingy and it just brings up the crash screen. I tried to reboot into Odin Mode, hooked up the phone to my computer and tried to reinstall a new ROM. First I tried with Odin 3.07 with a ROM I loaded onto it last month (I9300XXUGNA5_I9300AUTGNA1_I9300XXUGMK6_HOME.tar.md5), but the Odin program on the computer crashes each time. I also tried with an updated version of Odin, v1.85 and also Odin Auto. I had an issue last month, looked around and fixed it by downloading this ROM just mentioned, but this time, no joy. I've tried with another that I just downloaded (root66_TMO_T999UVDLJA.tar.md5) and the same thing happens. At one point, I received a message on different attempts where the Odin program would spit back at me this:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_TMO_T999UVDLJA.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1
So, how do I proceed from this point? I don't know enough to understand what the problem is with this, maybe something to do with the PIT mapping? I feel like I've covered every possible avenue that I can see posted online, I'm really not sure if there is anyone else with this problem, where the Odin program is so volatile. Your thoughts would be greatly appreciated, I suffer without my phone.
Stuart
Click to expand...
Click to collapse
Happened the same too me and i have CM11 too... If you get a fix contact me please
emnt said:
Happened the same too me and i have CM11 too... If you get a fix contact me please
Click to expand...
Click to collapse
Try the above rescue firmware as suggested above make sure you know what you are doing before flashing.. Exactly same advice if that doesn't work service required partition corrupt..Also I noticed the op above also flashed wrong root file for I9300 which didn't help.
blackbeardtwenty said:
The unusual thing about this crash was that it rebooted with a fuzzy, static-like screen,
Click to expand...
Click to collapse
Hardware issue, either damaged or corrupt emmc chip.
tallman43 said:
.Also I noticed the op above also flashed wrong root file for I9300 which didn't help.
Click to expand...
Click to collapse
Yeah, that was a desperate attempt at trying another root file which was recommended in another post. I initially used:
I9300XXUGNA5_I9300AUTGNA1_I9300XXUGMK6_HOME.tar.md5
and this worked fine last month, but now I'm back to square one again. Any ideas on other PIT files or root files I can download which might do the trick?
Thanks for your comments so far, you're all a bunch of wizards...