Hello I are trying unbrick my LG L7X but i cant!
when i tried to flash the device, an error appears
[see the image below]
http: //i.imgur.com/AwtLxma.jpg
and the device dont make anything.. the emergency mode screen is still without restart or other thing..
I already download the all firmwares of Mexico (TELCEL) displayed here http ://lg-phone-firmware.com/index.php?id_mod=21 and is not working too, =(
My phone information is:
Model: LGP714
Country: Mexico
Phone Company: TELCEL
______________________________
also when i install a kdz called "V20A_01.kdz" any error appears in the KDZ Updater Tool, the phone restarts after the flash is full but dont working.
The phone is stocked in the LG Logo and dont make anything, i only can enter to the emergency mode again using:vol+ + connecting the USB after.
I really need help, i already go to the "technologhy center" in my country and any body haves a idea of what happens with my phone Lol.
sorry for my bad english,
Anybody can help?
HELP ME =(
my phone its bricked... today
Anyone can help me? please
flomix77 said:
Anyone can help me? please
Click to expand...
Click to collapse
What procedure you use to flash KDZ? Have you try emergency mode in updater? Have you CWM installed on device?
And yes, it is worst scenario when you try to flash rom for other device...
maxx_hr said:
What procedure you use to flash KDZ? Have you try emergency mode in updater? Have you CWM installed on device?
And yes, it is worst scenario when you try to flash rom for other device...
Click to expand...
Click to collapse
I are following these steps:
(when i turn on my phone only the LG logo appears)
1.- Turn Off my Phone
2.- Configure the KDZ Updater settings, Type 3GQCT and mode CS_EMERGENCY (I already tried the all modes)
3.- remove the batery
4.- Connect the USB and press vol+
5.- Now are in emergency mode (windows has detected the device because i already have the LG drivers and PC Suite)
6.- Click on "Launch Software Update"
7.- Wait while the firmware is installing..
i already use a application to found my original (official) firmware from LG page (V10A_09.kdz TCL/TELCEL MEXICO)
But when i tried install this kdz an error appears in the Updater KDZ (in the 14% of progress) and the phone its bricked on emergency mode..
I already tried a lot of differents KDZ Files, V20A_00, V120H_00, and nothing...
How i can do?
flomix77 said:
I are following these steps:
(when i turn on my phone only the LG logo appears)
1.- Turn Off my Phone
2.- Configure the KDZ Updater settings, Type 3GQCT and mode CS_EMERGENCY (I already tried the all modes)
3.- remove the batery
4.- Connect the USB and press vol+
5.- Now are in emergency mode (windows has detected the device because i already have the LG drivers and PC Suite)
6.- Click on "Launch Software Update"
7.- Wait while the firmware is installing..
i already use a application to found my original (official) firmware from LG page (V10A_09.kdz TCL/TELCEL MEXICO)
But when i tried install this kdz an error appears in the Updater KDZ (in the 14% of progress) and the phone its bricked on emergency mode..
I already tried a lot of differents KDZ Files, V20A_00, V120H_00, and nothing...
How i can do?
Click to expand...
Click to collapse
Try this:
1. Download older version of kdz updater: https://www.dropbox.com/s/w8h5t1mqcuclijv/KDZ_FW_UPD_EN.rar
2. unpack it on root of c:
3. Pull out LAN cable, or disable internet connection
4. Run msxml.msi from unpacked kdz_fw_upd_en folder
5.put the KDZ you download previously and be carefull to choose only KDZ FOR YOUR DEVICE on root of C:
6. Turn off the phone, hold the volume "down" and insert the USB cable, should see a yellow background and the words "Emergency mode"
7. Run KDZ_FW_UPD.exe
8. choose parameters 3GQCT and DIAG, select the firmware file (KDZ)
9. Click Launch software update and wait...
10. If update stuck again on some %, (stuck means no progres for long time, like 10-15 min), unplug USB, pull out battery, reinsert and repeat from step 6. If you are lucky, mabe previous flash turns back partition organisation destroyed by flashing firmware for other phones, and second flash finish succesfull. In that case, do factory reset,,
11. good luck
11.
The error appears again
maxx_hr said:
Try this:
1. Download older version of kdz updater:
2. unpack it on root of c:
3. Pull out LAN cable, or disable internet connection
4. Run msxml.msi from unpacked kdz_fw_upd_en folder
5.put the KDZ you download previously and be carefull to choose only KDZ FOR YOUR DEVICE on root of C:
6. Turn off the phone, hold the volume "down" and insert the USB cable, should see a yellow background and the words "Emergency mode"
7. Run KDZ_FW_UPD.exe
8. choose parameters 3GQCT and DIAG, select the firmware file (KDZ)
9. Click Launch software update and wait...
10. If update stuck again on some %, (stuck means no progres for long time, like 10-15 min), unplug USB, pull out battery, reinsert and repeat from step 6. If you are lucky, mabe previous flash turns back partition organisation destroyed by flashing firmware for other phones, and second flash finish succesfull. In that case, do factory reset,,
11. good luck
11.
Click to expand...
Click to collapse
bit.*ｌy/1qp04s5
bit.*ｌy/1lqlfT1
bit.*ｌy/1iKwMC4
(remove * because i cant post links for the images)
The problem persists how i can do?
I can install the firmware V20A_00.kdz but the phone its bricked on the LG logo, and dont work. if i try install other firmwar (V10A_09.kdz) the kdz updater shows a error, T_T
flomix77 said:
bit.*ｌy/1qp04s5
bit.*ｌy/1lqlfT1
bit.*ｌy/1iKwMC4
(remove * because i cant post links for the images)
The problem persists how i can do?
I can install the firmware V20A_00.kdz but the phone its bricked on the LG logo, and dont work. if i try install other firmwar (V10A_09.kdz) the kdz updater shows a error, T_T
Click to expand...
Click to collapse
DONT TRY TO INSTALL OTHER PHONE FIRMWARE (V20A_00.kdz)! Flash only kdz for your model, like V10a_08.kdz, and download it from http://lg-phone-firmware.com/index.php?id_mod=21, in Mexico section.
No known similar firmware is available for your phone!
maxx_hr said:
DONT TRY TO INSTALL OTHER PHONE FIRMWARE (V20A_00.kdz)! Flash only kdz for your model, like V10a_08.kdz, and download it from http://lg-phone-firmware.com/index.php?id_mod=21, in Mexico section.
No known similar firmware is available for your phone!
Click to expand...
Click to collapse
My original phone firmware is V10A_09.kdz and the kdz updater shows a error if i try install it T.T
flomix77 said:
My original phone firmware is V10A_09.kdz and the kdz updater shows a error if i try install it T.T
Click to expand...
Click to collapse
Have you try to install V10A_08.kdz? This is older version of WORKING firmware for your device, just try...
There's no v20 ROM for L7 II until right now while I'm writing this message (and it's just a name that indicates the version for that specific model - e.g. v10 is ICS and v20 is JB in P700, while v10 is JB in P710 - so don't try to compare them in any way).
You simply flashed the wrong firmware, you flashed the firmware of another LG model in your phone, probably a L7 I ROM via KDZ.
The bad news is until today I found no way to fix the phone, see my topic: http://forum.xda-developers.com/showthread.php?t=2743453
OK
On this link (maby) you can find another way to flash KDZ: http://forum.xda-developers.com/showthread.php?p=51612244
Yes, you must change some things to work, but this is the last chance for your device.
And I remember that i was read one similar post before few months, for L7 II, but i can't find it anymore. In that post someone describe how to resolve his bricked phone problem, with link to post where he was find solution how to succesfully flash firmware... this post you cant find in LG L3 II - 5 - 7 II section.
So, just keep trying, and please, share with us what you do. If you dont understand procedure, just ask, and maby I have (or someone else) answer.
Good luck
Hi thanks for the suggestion...
It looks like the phone isn't able to enter Download Mode (required for FlashTool?), because it always turn on in emergency... Or am I doing something wrong? I'm not sure about the key combination for L7 II, I can't find it anywhere...
rafaelluik said:
Hi thanks for the suggestion...
It looks like the phone isn't able to enter Download Mode (required for FlashTool?), because it always turn on in emergency... Or am I doing something wrong? I'm not sure about the key combination for L7 II, I can't find it anywhere...
Click to expand...
Click to collapse
Try this: http://forum.xda-developers.com/showpost.php?p=54044924&postcount=2
maxx_hr said:
Try this: http://forum.xda-developers.com/showpost.php?p=54044924&postcount=2
Click to expand...
Click to collapse
It doesn't work. It goes straight to emergency mode. And those instructions are in a L3 II topic, what if the combination for L7 II is different (involves the hotkey IDK)?
rafaelluik said:
It doesn't work. It goes straight to emergency mode. And those instructions are in a L3 II topic, what if the combination for L7 II is different (involves the hotkey IDK)?
Click to expand...
Click to collapse
I think emergency mode is download mode...
rafaelluik said:
It doesn't work. It goes straight to emergency mode. And those instructions are in a L3 II topic, what if the combination for L7 II is different (involves the hotkey IDK)?
Click to expand...
Click to collapse
maxx_hr said:
I think emergency mode is download mode...
Click to expand...
Click to collapse
flomix77 said:
My original phone firmware is V10A_09.kdz and the kdz updater shows a error if i try install it T.T
Click to expand...
Click to collapse
http://forum.xda-developers.com/showpost.php?p=54504577&postcount=10
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
When i want to get in emergency/download mode, on the screen appears this blue stripes.
IGGYVIP i try your guide, but when i want flash KDZ, it is the same result as all. (IP PARAM: 0 etc.)
It is possible, that my phone will ok?
Please help
Hi
I am facing same problem described here.
I flashed wrong rom on my LG P715 and now it is bricked. Before flashing I rooted the device and installed CWM recovery. I am having same blue screen now.
Please help me.
Thank you in advance.
Harish
harishc said:
Hi
I am facing same problem described here.
I flashed wrong rom on my LG P715 and now it is bricked. Before flashing I rooted the device and installed CWM recovery. I am having same blue screen now.
Please help me.
Thank you in advance.
Harish
Click to expand...
Click to collapse
From here do this:
http://forum.xda-developers.com/opt...torial-how-to-achieve-root-p710-l7-2-t2921271
REMOVE ALL DRIVERS OF ANDROID YOU HAVE (Lg Adb all). Reinstall the drivers I provided there and adb. After that just plug usb in and turn phone on. Tell me as what is getting recognized (in device manager).
Related
*My apologies, I am a noob, I am new to XDA, I still cannot include the links. Send me a message or comment, I'll give you the links. Sorry.*
Follow the instructions given below:
1. Download LG Optimus L3 E400 USB Driver.
2. Download official LG Optimus L3 E400 stock firmware. It is a .kdz file.
3. Download KDZ Updater and of course, install it.
4. Install LG Optimus L3 E400 USB Driver and restart PC after installation is complete.
After reboting your(restarting) PC...
5. Put your phone into recovery mode.
A yellow screen will appear with "Emergency mode!!" written on it.
6. Now connect your phone to the computer via USB Cable.
7. Run KDZ Updater (KDZ_FW_UPD.exe) as Administrator.
8. Choose the following options in KDZ Updater:
Type: 3GQCT
Phone Mode: DIAG
9. Browse for the .kdz file you've downloaded.
10. Click on "Launch software update."
This process usually takes long time. If nothing goes wrong... try left haha :laugh: just kidding.
If everything goes well, you should see "FINISHED" on the last line on the log screen.
Your phone will automatically reboot (just like what happened on mine). There you go,
your precious phone is back.
If there are more queries regarding this problem, please comment. I'll do everything
I can. I hope I helped. :angel:
LG L3 bricked
Sir,
my lg l3 now in emergency mode, i want to update with stock firmware. so if you kindly give me the link where i download the kdz file.
urgent please...
thanking you
nidalovesu
nidalovesu said:
Sir,
my lg l3 now in emergency mode, i want to update with stock firmware. so if you kindly give me the link where i download the kdz file.
urgent please...
thanking you
nidalovesu
Click to expand...
Click to collapse
You can find stock roms here www. lg-phone-firmware .com/
nidalovesu said:
Sir,
my lg l3 now in emergency mode, i want to update with stock firmware. so if you kindly give me the link where i download the kdz file.
urgent please...
thanking you
nidalovesu
Click to expand...
Click to collapse
Hi i tried to do this on l3 e400 with CM9 to have stock rom installed but the updater crashed since then i can't get emergency mode, it displays an error "demigod crash handler", i reboot the phone and cm9 worked normally, i used the power button then choosed reboot, and selected bootlader the phone rebooted but no bootloader if displays some lines of code "img/..", i tried also to reboot in to recovery and it works normally CWM installed.
Any idea to repair the emergency mode and install stock rom ?
No reply, i solved my problem thx.
Just removed the battery and entered emergency mode and it worked
Sent from my HTC Desire S using xda app-developers app
Attention, Do On Your Own Risk
I am not responsible if there is any damage to your device
And read this carefully
ONLY FOR LG L7 II P713
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Let's get started it
First, check your software, go to settings> about phone> software information
If you are already using firmware p71310e-ESA-XX
You can directly use the apk below to rooting process
download apk from here
- install apk
- open it, and select the Superuser or SuperSU(Recomended use this)
- Click Gandalf
- Reboot
You have succesfully rooted your device
For non p7130e-ESA-XX user
Follow these instruction
>First, Download all these
1. USB Driver
2. KDZ FW Updater
3. Download Firmware LG L7 with Root support from here
4. Choose THA/THAILAND V10E LGP713
5. Download apk from here
Second, install
1. Usb Driver
2. Extract the KDZ FW Updater, find msxml.msi and instali it
3. Connect the device computer, do not forget to check the USB debugging on, once there select the connection notification, select Software LG
4. Open KDZ update
Choose Type =3GQCT
Phone Mode =DIAG
5.Browse File KDZ that you've download, then click ''Launch Software Update"
6. Find some food until the process is done,
cause It's take a long time, between 15-20 minutes, i'm not kidding
7. Install apk
8. Open it, and select the Superuser or SuperSU(Recomended use this)
9. Click/Choose Gandalf
10. Reboot your device
Finally, You have succesfully rooted your device
Special thanks
@alephzain
for this awesome application
Of course, all of these operations need the right Root User
1. Download and unpack this archive boothack+recovery
2. Install the program Gscript.apk on your phone
3. File boothack-cwm.sh put the path /storage/sdcard0/gscript /
4. APPSSBL.bin and recovery.img files put the path /storage/external_SD/
5. Run a previously installed Gscript
6. Press the softkey menu -> Add Script -> Load File -> boothack-cwm.sh -> save (it is added to the list)
7. Click on the saved script boothack-cwm
8. You're done! (the phone will restart in recovery mode)
Known issues at the moment:
1. The problem with the display. Displayed upside down and while navigating jumps in width. At this point in the stage of searching for a solution. Nevertheless, all necessary functions are performed
Solution for bootloop problem while using CWM
solution is: pull out the battery > plug in to USB or charger if you don't have pc > just let it blinks with LG logo > now put your battery in, you will see the battery icon charged > plug out the cable > then turn it on like usual.... wallaa... you got your phone back to home...
after this, please use kdz flasher to remove cwm recovery ( do not wipe data if you won't )
that's all... cheers
credit goes to
thanks @yayakuya for the solution
Reserved
I want to ask something. Will framaroot 1.7.0 work on 10D ? If not, why not using motochoper instead ?
Sent from my LG-P713 using xda app-developers app
thank ,i was rooted for my p713 .
but i can't install recovery .
karkand said:
I want to ask something. Will framaroot 1.7.0 work on 10D ? If not, why not using motochoper instead ?
Sent from my LG-P713 using xda app-developers app
Click to expand...
Click to collapse
nope, 10d didn't working with all framaroot version, you must change you fw
vananuan said:
thank ,i was rooted for my p713 .
but i can't install recovery .
Click to expand...
Click to collapse
open this thread to install cwm
http://forum.xda-developers.com/showthread.php?t=2277972&page=2
follow the instructions
please note this
the recovery doesn't stable yet, don't blame anyone if there's something wrong later
vananuan said:
thank ,i was rooted for my p713 .
but i can't install recovery .
Click to expand...
Click to collapse
Thx. Now my phone root
Sent from my LG-P713 using xda app-developers app
damn... my p713 was v10a
i hate to play with flasher...
but nvm, thanks for those bro,
can't do oplosan shake before breaking the system
yayakuya said:
damn... my p713 was v10a
i hate to play with flasher...
but nvm, thanks for those bro,
can't do oplosan shake before breaking the system
Click to expand...
Click to collapse
you're welcome brother
just shaking the oplosan dance at the same time while you breaking the system
happy dancing and happy flashing
nasheich said:
you're welcome brother
just shaking the oplosan dance at the same time while you breaking the system
happy dancing and happy flashing
Click to expand...
Click to collapse
oi bro...
why after I pull my sdcard out, my phone just going to bootloop...
I still can go to cwm, but why that's only for few seconds then it just reboot it self???
I can't do restore the backup coz it will be rebooted while in the middle of process...
the worst thing, I can't use kdz flasher coz adb can not read my phone while in bootlooping (actually it's readable, but the bootloop is not stucked... it's round over n over again)
so adb just read for a while coz phone turned off n then restarted again...
did you know which buttons combo for bring it to emergency mode?
thanks
yayakuya said:
oi bro...
why after I pull my sdcard out, my phone just going to bootloop...
I still can go to cwm, but why that's only for few seconds then it just reboot it self???
I can't do restore the backup coz it will be rebooted while in the middle of process...
the worst thing, I can't use kdz flasher coz adb can not read my phone while in bootlooping (actually it's readable, but the bootloop is not stucked... it's round over n over again)
so adb just read for a while coz phone turned off n then restarted again...
did you know which buttons combo for bring it to emergency mode?
thanks
Click to expand...
Click to collapse
1. don't use cwm for now, isn't stable yet
2. like Samsung's device, use combination of home+volume down+power to go emergency mode
3. if the number 2 doesn't work, pull out the battery, connect your device to PC(don't use the battery) and go to emergency mode by holding home+volume down+power as fast as you can
4. now flash the stock rom using kdz updater again(make sure you downloaded that)
sorry for late reply, I'm busy dancing oplosan
nasheich said:
1. don't use cwm for now, isn't stable yet
2. like Samsung's device, use combination of home+volume down+power to go emergency mode
3. if the number 2 doesn't work, pull out the battery, connect your device to PC(don't use the battery) and go to emergency mode by holding home+volume down+power as fast as you can
4. now flash the stock rom using kdz updater again(make sure you downloaded that)
sorry for late reply, I'm busy dancing oplosan
Click to expand...
Click to collapse
thanks mate..
ok, now i'll try it then report to you soon...
___edit__
kdz won't read the emergency mode!
I was trying those three modes in kdz, but phone can't read it.... :$
yayakuya said:
thanks mate..
ok, now i'll try it then report to you soon...
Click to expand...
Click to collapse
you're welcome
yayakuya said:
thanks mate..
ok, now i'll try it then report to you soon...
___edit__
kdz won't read the emergency mode!
I was trying those three modes in kdz, but phone can't read it.... :$
Click to expand...
Click to collapse
make sure you have install the driver first
use driver from the op
nasheich said:
you're welcome
Click to expand...
Click to collapse
how to read the phone in emergency mode?
the LG United driver only read adb....
any suggestion?
yayakuya said:
how to read the phone in emergency mode?
the LG United driver only read adb....
any suggestion?
Click to expand...
Click to collapse
like in the op, just change the "Phone Mode" to "Emergency Mode" at the KDZ Updater
Second, install
1. Usb Driver
2. Extract the KDZ FW Updater, find msxml.msi and
instali it
3. Connect the device computer,
4. Open KDZ update
Choose Type =3GQCT
Phone Mode =DIAG > change to emergency mode
5.Browse File KDZ that you've download, then click
''Launch Software Update"
6. Find some food until the process is done,
nasheich said:
like in the op, just change the "Phone Mode" to "Emergency Mode" at the KDZ Updater
Second, install
1. Usb Driver
2. Extract the KDZ FW Updater, find msxml.msi and
instali it
3. Connect the device computer,
4. Open KDZ update
Choose Type =3GQCT
Phone Mode =DIAG > change to emergency mode
5.Browse File KDZ that you've download, then click
''Launch Software Update"
6. Find some food until the process is done,
Click to expand...
Click to collapse
like I was mentioned above, I did try those three mode "emergency n cs_emergency mode" but still phone not found...
but nevermind, I've got new solution for it by my self....
if you guys having problem after installing cwm n do normal reboot, it will never bring you to the home screen... it's just bootloop...
solution is: pull out the battery > plug in to USB or charger if you don't have pc > just let it blinks with LG logo > now put your battery in, you will see the battery icon charged > plug out the cable > then turn it on like usual.... wallaa... you got your phone back to home...
after this, please use kdz flasher to remove cwm recovery ( do not wipe data if you won't )
that's all... cheers
I'm not using LG L7 anymore, i was changing about 2 months ago
btw, I'll put it at first page if you don't mind
Hello, i have a question. How to back from 4.4.2 android to 4.1.2 android? i need 4.4.2 no root in my phone. :c Thanks for replies
Hello!
Hello, to revert to Jellybean you need to flash a KDZ file of Jellybean, here you can find it:
http://lg-phone-firmware.com/index.php?id_mod=21 (Every with V10 version is Jellybean, V20 is KitKat)
VERY IMPORTANT!
After installer the Jellybean rom and finish with the flashing, you need to do a hard reset or it wont boot.
Hard reset:
Press Volumen Down - Power Key and Quick memo Key at the same time
When LG logo appear, release the Power Key one
When LG logo disappear, release all the buttoms. It'll appear a Android robot and when it finish, boot.
If u don't know how to flash KDZ ask me!
Hello Juaaanchi,
How to flash KDZ in my phone P710?
Thanks
pjprojekce said:
Hello Juaaanchi,
How to flash KDZ in my phone P710?
Thanks
Click to expand...
Click to collapse
1. Download the .kdz file. I should be named V10A, V20C etc.
2. Install your device drivers.
3. Connect USB wire to PC.
3. Turn off the phone and enter download mode by taking out the battery, pluging in USB while holding VOLUME DOWN button.
4. Open LG update tool (DOWNLOAD HERE) <MODERATOR EDITED - VIRUS / TROJAN LINK REMOVED>
5. Don't change anything, just select your .kdz file.
6. Press start, next, select enlgish and wait.
7. Then your phone should reboot into stock ROM.
That's all. Write if something goes wrong.
i was use this tool, with CSE mode. but when firmware finish extracted, this tool stop responding. in the detail report APP CRASH happened.
i try with NORMAL mode. but when the tool flash my device, in 5% my device disconnect unexpectedly. i've already instal the driver with LG port, modem, and usb device. but that also happened again and again
pjprojekce said:
i was use this tool, with CSE mode. but when firmware finish extracted, this tool stop responding. in the detail report APP CRASH happened.
i try with NORMAL mode. but when the tool flash my device, in 5% my device disconnect unexpectedly. i've already instal the driver with LG port, modem, and usb device. but that also happened again and again
Click to expand...
Click to collapse
Use LGFlashtool in EMERGENCY MODe and 3GCQT, and it will work
Can anyone help me with jelly bean kdz file link?
Thank you.
First of all, This is not entirly my original work. credits goes to quangnhut123 , who modified LG Flash tool for us. I am just sharing this GUIDE for flashing lolipop to L90
Quote:
I have tested this method myself and it is working perfectly for me, but it is also possible that it might not work for you for some reasons, so don't panic, just post your problem or whatever error you are facing (please attach screenshot if possible). I or other thread members will try to troubleshoot it. After resolving the problem I'll update this post, so that other members do not face such problem again.
Quote:
PLEASE, USE THIS TUTORIAL AT YOUR OWN RISK, IF SOMETHING WENT WRONG (because of your stupidity) ME OR XDA WILL NOT RESPONSIBLE FOR YOUR LOSS.
Flashing KDZ file removes Root and CWM, so you will need to root again.
Flashing KDZ file does not wipe your data, but if you get bootloops you need to hard-reset it, so please backup data first.
Note -
EVERYTHING IN THIS ROM IS WORKING Even the Knock Code , Camera ,DOuble Tap, ANd Everything Your DEvice Is Capable Of.
If Due To Some Reason Your Device Slows Down After The Update Please Do A Factory Reset Of the Device It Will Work Fine Again With Lolipop. :good:
1. Download KDZ file
To download KDZ File Of Lolipop for you Device GOTO
https://yadi.sk/d/PRPkYggqf4v4C For lolipop 5.0.2
https://yadi.sk/d/2OoNsU3wf5vku For lolipop 5.0.0
2. Precautions:-
Enable Show Hidden Files in Folder Option (Don't disable this option until kdz flashing process completes) and Delete the LG Mobile Tool folder (if exist) from
C:\ProgramData\
Remove all other USB devices (external HDD, backup drives, other phones, etc.) and cables connected to PC to avoid issued due to voltage loss.
OFFLINE KDZ FLASHING DOES NOT LOOSE PHONE DATA, BUT YOU MUST BACKUP YOUR PHONE IN ANY CASE.
3. Downloads:-
Download The Zip File From Here- http://www.mediafire.com/download/s2qqa3p464pbxp7/LG_Flash_Tool_2014.zip
4. Install LG Drivers (internet required for this):
Extract B2CAppSetup.zip anywhere on PC and Run B2CAppSetup.exe as administrator. Accept Agreement and a window will appear. Click on OK button (Bottom Right) on instructions. Now connect your LG Device to PC in LG Software mode. B2CAppSetup tool will detect it. Now Click on Install USB Drivers (2nd option on Top Left). It will automatically download and install drivers for your device. If Install USB Drivers options goes grey (Disable) after detecting phone, it means latest USB Drivers are already installed.
After installing USB Drivers please REBOOT YOU PC
Now Connect Phone in Software Upgrade Mode: Switch OFF the phone and Press VolumeUP button and insert USB cable into the phone, Now phone should show Firmware Upgrade Mode.
Let windows load any drivers, wait until it finishes. TWO ENTRIES SHOULD APPEAR IN DEVICE MANAGER IF DRIVERS ARE PROPERLY INSTALLED
Download File From Here- http://www.mediafire.com/download/3ir140wxq9mxa31/B2CAppSetup.zip
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
After installing device drivers unplug the phone from PC
5. Starting The Installation Process:
Extract LG Flash Tool 2014.zip to A Folder
Note-
Copy The KDZ file to the same folder where all the files of lg Flash Tool 2014 is extracted- [For Better Results]
Open LG Flash Tool 2014 folder and run LGFlashTool2014.exe and administrator.
LG Flash Tool 2014 windows will appear.
Select "3GQCT" in Type of Flash.
Select "EMERGENCY" for PhoneMode.
Select your KDZ file in the Select KDZ File box.
Press "Normal Flash" button. (as pic below)
IMPORTANT: Do not change the names of the KDZ files. (They should look like.... "D41020B_00.kdz" )
Now Again Connect Phone in Software Upgrade Mode: Switch OFF the phone and Press VolumeUP button and insert USB cable into the phone, Now phone should show Firmware Upgrade Mode.
Now "Read Phone Information" box will open with blank information, Just press "Start"
Now "Select country and language" small box will open. Here select "Different Country" and "English" and press "OK"
The utility starts the official LG Mobile Support Tool
Now actual flashing will start, and if your KDZ file is good flashing will end without any issue.
JUST RELAX!! SIT BACK WITH HANDS FOLDED BEHIND HEAD AND WATCH IT HAPPENING.
When it finishes full flashing and phone will start rebooting.
YOU CAN REMOVE CABLE AFTER 100%, AND FLASHING IS FINISHED!!! Close all programs.
DON'T FORGET TO HIT THANKS IF IT HELPED...
.
Lets See It May or May Not Work
Martin213 said:
Nice tut thank you,can this build run on D405n?
Click to expand...
Click to collapse
Well I have Never Tested This On ANy Another Device Except For LG L90 D410
If you want to try this on your Lg L90 D405n i recommend to get a kdz file for your model as a backup
To download KZD for you Device GOTO lg-firmware-rom.com
Enter IMEI no of your device.
TO GET THE IMEI OF YOUR PHONE go to About Phone in settings and get your imei no or else remove the battery and see there it will be written.
Do Post If This Worked On Your Device
Best Of Luck With The Trial :good: :good:
my phone is lg l90 d410(v10d-IND-xx),can i flash using kdz flasher??
will there be any kind of problems???
Will a message box pops up when restart the phone: "this version is not for users"
Other languages
in the window "select country and language" is only available English? happens to have Portuguese?
Perfect
is working perfectly on my L90 d410nh......Thanks
Ya there might be a mag in some of the devices but that is due to network nothing is related to the rom and there will not be anybkind of problem due to it.
Sent from my LG-D410 using XDA Free mobile app
Xzyrate there is only english language option in this rom no other language is present
Wellbi am glad that i could help
Sent from my LG-D410 using XDA Free mobile app
Other languages
OsFreakxx said:
Xzyrate there is only english language option in this rom no other language is present
Wellbi am glad that i could help
Sent from my LG-D410 using XDA Free mobile app
Click to expand...
Click to collapse
Worked in portuguese!
Would this kdz work in 405n variant? Or at least with phew bugs?
I dont think that you should try this its a totally different varient as it has different hardware configuration
Sent from my LG-D410 using XDA Free mobile app
OsFreakxx said:
First of all, This is not entirly my original work. credits goes to quangnhut123 , who modified LG Flash tool for us. I am just sharing this GUIDE for flashing lolipop to L90
Quote:
I have tested this method myself and it is working perfectly for me, but it is also possible that it might not work for you for some reasons, so don't panic, just post your problem or whatever error you are facing (please attach screenshot if possible). I or other thread members will try to troubleshoot it. After resolving the problem I'll update this post, so that other members do not face such problem again.
Quote:
PLEASE, USE THIS TUTORIAL AT YOUR OWN RISK, IF SOMETHING WENT WRONG (because of your stupidity) ME OR XDA WILL NOT RESPONSIBLE FOR YOUR LOSS.
Flashing KDZ file removes Root and CWM, so you will need to root again.
Flashing KDZ file does not wipe your data, but if you get bootloops you need to hard-reset it, so please backup data first.
Note -
EVERYTHING IN THIS ROM IS WORKING Even the Knock Code , Camera ,DOuble Tap, ANd Everything Your DEvice Is Capable Of.
If Due To Some Reason Your Device Slows Down After The Update Please Do A Factory Reset Of the Device It Will Work Fine Again With Lolipop. :good:
1. Download KDZ file
To download KDZ File Of Lolipop for you Device GOTO
https://yadi.sk/d/PRPkYggqf4v4C For lolipop 5.0.2
https://yadi.sk/d/2OoNsU3wf5vku For lolipop 5.0.0
2. Precautions:-
Enable Show Hidden Files in Folder Option (Don't disable this option until kdz flashing process completes) and Delete the LG Mobile Tool folder (if exist) from
C:\ProgramData\
Remove all other USB devices (external HDD, backup drives, other phones, etc.) and cables connected to PC to avoid issued due to voltage loss.
OFFLINE KDZ FLASHING DOES NOT LOOSE PHONE DATA, BUT YOU MUST BACKUP YOUR PHONE IN ANY CASE.
3. Downloads:-
Download The Zip File From Here- http://www.mediafire.com/download/s2qqa3p464pbxp7/LG_Flash_Tool_2014.zip
4. Install LG Drivers (internet required for this):
Extract B2CAppSetup.zip anywhere on PC and Run B2CAppSetup.exe as administrator. Accept Agreement and a window will appear. Click on OK button (Bottom Right) on instructions. Now connect your LG Device to PC in LG Software mode. B2CAppSetup tool will detect it. Now Click on Install USB Drivers (2nd option on Top Left). It will automatically download and install drivers for your device. If Install USB Drivers options goes grey (Disable) after detecting phone, it means latest USB Drivers are already installed.
After installing USB Drivers please REBOOT YOU PC
Now Connect Phone in Software Upgrade Mode: Switch OFF the phone and Press VolumeUP button and insert USB cable into the phone, Now phone should show Firmware Upgrade Mode.
Let windows load any drivers, wait until it finishes. TWO ENTRIES SHOULD APPEAR IN DEVICE MANAGER IF DRIVERS ARE PROPERLY INSTALLED
Download File From Here- http://www.mediafire.com/download/3ir140wxq9mxa31/B2CAppSetup.zip
After installing device drivers unplug the phone from PC
5. Starting The Installation Process:
Extract LG Flash Tool 2014.zip to A Folder
Note-
Copy The KDZ file to the same folder where all the files of lg Flash Tool 2014 is extracted- [For Better Results]
Open LG Flash Tool 2014 folder and run LGFlashTool2014.exe and administrator.
LG Flash Tool 2014 windows will appear.
Select "3GQCT" in Type of Flash.
Select "EMERGENCY" for PhoneMode.
Select your KDZ file in the Select KDZ File box.
Press "Normal Flash" button. (as pic below)
IMPORTANT: Do not change the names of the KDZ files. (They should look like.... "D41020B_00.kdz" )
Now Again Connect Phone in Software Upgrade Mode: Switch OFF the phone and Press VolumeUP button and insert USB cable into the phone, Now phone should show Firmware Upgrade Mode.
Now "Read Phone Information" box will open with blank information, Just press "Start"
Now "Select country and language" small box will open. Here select "Different Country" and "English" and press "OK"
The utility starts the official LG Mobile Support Tool
Now actual flashing will start, and if your KDZ file is good flashing will end without any issue.
JUST RELAX!! SIT BACK WITH HANDS FOLDED BEHIND HEAD AND WATCH IT HAPPENING.
When it finishes full flashing and phone will start rebooting.
YOU CAN REMOVE CABLE AFTER 100%, AND FLASHING IS FINISHED!!! Close all programs.
DON'T FORGET TO HIT THANKS IF IT HELPED...
Click to expand...
Click to collapse
Im Try to flash but 47% done then software hang n stop
error at startup after phone finished booting up
Hi,
My LG L90 D410 phone started giving the below error at startup after I upgraded to Lollipop 5.0.2. Though everything works fine. please advice.
Thank you
Software Update...
hello...
My d410 got stuck at 54% when it was updating and ever since have been trying do it again but it will still stop at 54%... what can i do to revert it and i have tried factory resetting it but it still not working.... what can i do pls help....
dedoyin said:
hello...
My d410 got stuck at 54% when it was updating and ever since have been trying do it again but it will still stop at 54%... what can i do to revert it and i have tried factory resetting it but it still not working.... what can i do pls help....
Click to expand...
Click to collapse
Are u still facing the issue sorry for late reply i was busy with work
I don't think so those are two completely different variants
Video guide unbrick
https://www.youtube.com/watch?v=5HIc_tyiFcg
File support onlly qualcomm 9006 ( qhsusb_bulk show very partitiont)
Token:
No downloamod, no fastboot, no recovery, when connect cable phone detect qhsusb_bulk and show very partitiont
Check Diskmanagerment you see disk emmc of phone
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
If see Disk2 open 2hardisk.exe and choose model write number >enter waitting tool flash partitiont
Remember d802=d801=d802=d803 >>2
When flash done, remove cable, hold power 1 minute phone (turn off phone) and hold volume + connect cable phone put downloadmod, flash stock rom done.
Quote: If phone error when flash file tot Cross [] to[] you need use winhex change model file tot.(i will update guide in video,comming soon)
If phone blacksreen no detect driver qhsusb_bulk you need short testpoint.
[*]Guide attack testpoint:
Connect cable with out battery and short testpoint :
And testpoint Lg g2
When attack testpoint PC detect driver qhsusb_bulk and show very partitiont>> done
If detect qhsusb_bulk but not show very partitiont>> you need remove cable connect again> short testpoint again>>repeat until many partitiont> done> use tool of my unbrick.
File download unbrick qhsusb_bulk show very partitionts:
UNBRICKD800.rar
https://mega.nz/#!mN0SkDpb!1R36L-F05b8LxXXzcGwBctKgLEACz88X5OuIqwNdezM
UNBRICKD801.rar
https://mega.nz/#!KRF3GIxJ!hKNBOYOJNMOuzwd-4J2FVH0X6L9ebQEK_dOrMGDgxOw
UNBRICKD80216GB.rar
https://mega.nz/#!SJETXBAZ!YyfHa2oONsTzzS6LkM7tHaxotatU5rU8uDXZwP0q6pk
UNBRICKD80232GB.rar
https://mega.nz/#!HME1WKRD!RfciXv1-9C0Vwh53bf5j2S9jQMxUnwt7cgnqkpi7S48
UNBRICKD803.rar
https://mega.nz/#!eUtEkLqC!5m7EYuG2OniMEKZqNmFCoTeDW4LLmzxrTIhyD3ZXwE4
UNBRICKD80516GB.rar
https://mega.nz/#!rMUjHLYZ!yHwPKNpEsAGZO0icja39JMosa3k_EBABevuPzmipsaE
UNBRICKD80532GB.rar
https://mega.nz/#!3d8SybBJ!F4902UnBFCG3cq7eB6SJFbvvO3o96szU44RRie3xbVQ
UNBRICKls980.rar
https://mega.nz/#!jE0SRDpa!5xJqc7YW-j_kL4nKRyVVGy7ijBTjgJj8P2_XGjST7F8
UNBRICkvs980.rar
https://mega.nz/#!LNMD2QDJ!GK-dnv5umeg6k0A-fI6jnBF46rlT6Ks3BG_TDTrXw60
]
And update model : comming soon(waitting upload)
Quote:
[*]Unbrick done but phone BLACK SCREEN OR qhsusb_bulk show very partitiont again( unplug battery inplug again) if still the same
[*]You need check model behind the mainboard see pictrure and short testpoint download file right model unbrick again:
computer detect so many drives I use this method
1. (Turn off LG G2)
...
2. (Plug G2 into computer)
...
3. (It show so many drive like pictures in post)
...
4. (Press vol up + power button until G2 turn off)
...
5. (Release power button But still hold Vol up until G2 enter to downlaod)
...
6. (You can flash firmware KDZ now.)
somboons said:
computer detect so many drives I use this method
1. (Turn off LG G2)
...
2. (Plug G2 into computer)
...
3. (It show so many drive like pictures in post)
...
4. (Press vol up + power button until G2 turn off)
...
5. (Release power button But still hold Vol up until G2 enter to downlaod)
...
6. (You can flash firmware KDZ now.)
Click to expand...
Click to collapse
you lucky>>>partitiont laf not wrong if wrong you can put downloadmod
tungkick said:
File support onlly qualcomm 9006 ( qhsusb_bulk show very partitiont)
Token:
No downloamod, no fastboot, no recovery, when connect cable phone detect qhsusb_bulk and show very partitiont
Check Diskmanagerment you see disk emmc of phone
If see Disk2 open 2hardisk.exe and choose model write number >enter waitting tool flash partitiont
Remember d802=d801=d802=d803 >>2
When flash done, remove cable, hold power 1 minute phone (turn off phone) and hold volume + connect cable phone put downloadmod, flash stock rom done.
Quote: If phone error when flash file tot Cross [] to[] you need use winhex change model file tot.(i will update guide in video,comming soon)
If phone blacksreen no detect driver qhsusb_bulk you need short testpoint.
[*]Guide attack testpoint:
Connect cable with out battery and short testpoint :
And testpoint Lg g2
When attack testpoint PC detect driver qhsusb_bulk and show very partitiont>> done
If detect qhsusb_bulk but not show very partitiont>> you need remove cable connect again> short testpoint again>>repeat until many partitiont> done> use tool of my unbrick.
File download unbrick qhsusb_bulk show very partitionts:
File d800: https://mega.co.nz/#!zdVAGBDK!1R36L-F05b8LxXXzcGwBctKgLEACz88X5OuIqwNdezM
File d801 :https://mega.co.nz/#!6NdARC7a!hKNBOYOJNMOuzwd-4J2FVH0X6L9ebQEK_dOrMGDgxOw
File d802 16gb : https://mega.co.nz/#!jU0zyZbY!YyfHa2oONsTzzS6LkM7tHaxotatU5rU8uDXZwP0q6pk
File d802 32gb: comming soon.
File d805 16gb: https://mega.co.nz/#!jU0zyZbY!YyfHa2oONsTzzS6LkM7tHaxotatU5rU8uDXZwP0q6pk
File d805 32gb: https://mega.co.nz/#!OF9gVYIb!F4902UnBFCG3cq7eB6SJFbvvO3o96szU44RRie3xbVQ
File D803 :https://mega.co.nz/#!HMsUTQDQ!5m7EYuG2OniMEKZqNmFCoTeDW4LLmzxrTIhyD3ZXwE4
File LS980: https://mega.co.nz/#!zctw1DLR!5xJqc7YW-j_kL4nKRyVVGy7ijBTjgJj8P2_XGjST7F8
FILE VS980:https://mega.co.nz/#!3ZUnxI5I!GK-dnv5umeg6k0A-fI6jnBF46rlT6Ks3BG_TDTrXw60
And update model : comming soon(waitting upload)
Click to expand...
Click to collapse
I want to re write this dd command.
Do you have the pratition table for lg g3 or gpro2 or gflex??
Any model partition table list?
How to Power off after Harddisk1.exe flashing? Forcing Phone in 9006 Mode by shorting capictors required button plate to be removed...
Sent from My LG G Flex LG-F340K Stock KitKat V20D on LTE Network using XDA Free Mobile app
sorry OP, but where's the instruction? what i have to do with the file i download?
@somboons:
i cannot enter download mode.. have tried that usual key combo for download mode.. just LG logo appear and then looping
hacklockx said:
I want to re write this dd command.
Do you have the pratition table for lg g3 or gpro2 or gflex??
Any model partition table list?
Click to expand...
Click to collapse
GPRO2 GLEX SAME F320
copy all file *.img gpro2 glex to forther tool and choose 1(f320..) enter
shenlihartono said:
sorry OP, but where's the instruction? what i have to do with the file i download?
@somboons:
i cannot enter download mode.. have tried that usual key combo for download mode.. just LG logo appear and then looping
Click to expand...
Click to collapse
you need short testpoint and check mainboard if sure model download file unbrick and unbrick again
Thankyou!
thankyou very much. I have the international version d802 32GB and i didnt realize that so i did this procedure with the 16gb files and it still worked!
after i used the tool i installed the kdz for europe from this page:
http://forum.xda-developers.com/showthread.php?t=2432476
for my version (europe open) it was the D80220D_00.kdz file. i put the phone in download mode and could flash in kdz filer.
After that it was back to stock. REALLY THANKYOU!
tungkick said:
you need short testpoint and check mainboard if sure model download file unbrick and unbrick again
Click to expand...
Click to collapse
My Baseband and IMEI is Null, I have tried D802 Nd D801 both.. But Baseband isn't coming back...
Sent from My LG G Flex LG-F340K Stock KitKat V20D on LTE Network using XDA Free Mobile app
hacklockx said:
Unbrick all lg model ( lg g, g2, g3, gpro, gpro 2 , gflex, vu2 ,vu3 , nexus 5)
Click to expand...
Click to collapse
good boy but careful admin xda not pulish inbox^^.
if you unbrick free you can say user inbox, if unbrick fee careful^^
Can someone help? I messed up pretty bad this time @tungkick QHUSB_BULK not detected in download.mode and security error on boot.
ktetreault14 said:
Can someone help? I messed up pretty bad this time @tungkick QHUSB_BULK not detected in download.mode and security error on boot.
Click to expand...
Click to collapse
So you lost download mode?
Please let me know
hacklockx said:
So you lost download mode?
Please let me know
Click to expand...
Click to collapse
Check out the other thread I will copy it over here also. It shows all steps
ktetreault14 said:
Can someone help? I messed up pretty bad this time @tungkick QHUSB_BULK not detected in download.mode and security error on boot.
Click to expand...
Click to collapse
Phone hand logo security
You need short testpoint phone detect qualcomm 9006.And use tool unbrick
tungkick said:
Phone hand logo security
You need short testpoint phone detect qualcomm 9006.And use tool unbrick
Click to expand...
Click to collapse
Oh no I have to take the back off and short it out. I don't want to break anything lol even though I can't break it more than it already is
Murshad007 said:
My Baseband and IMEI is Null, I have tried D802 Nd D801 both.. But Baseband isn't coming back...
Sent from My LG G Flex LG-F340K Stock KitKat V20D on LTE Network using XDA Free Mobile app
Click to expand...
Click to collapse
you need read dump modemst1 modemst2 modem efs phone same you another or send telephone repairmain thay use octopus fix repair security
tungkick said:
you need read dump modemst1 modemst2 modem efs phone same you another or send telephone repairmain thay use octopus fix repair security
Click to expand...
Click to collapse
Thankyou, For replying.. I have given it to a Repairman with OCTO Box and Other Device similar... But I thinks he didn't knew much about it...
I will try another...
Sent from My LG G Flex LG-F340K Stock KitKat V20D on LTE Network using XDA Free Mobile app
Please help for a file for LG VU3 F300K, thank you!