Hello,
some of us who have bought a Hero locked to Orange can't seem to get it unlocked (http://forum.xda-developers.com/showthread.php?t=555424).
For those have you who have managed to successfully unlock an Hero on Orange please can you advise on your experience- did you have to do something differently? And who you used to get the code? I have used Unlock Now (www.unlock-now.com) but the code they have supplied didn't work (they refunded me).
I have never had a problem unlocking a HTC phone until now and I find it hard to believe that Orange Heros can't be unlocked.
Please help if you can.
*********************************************************
[Update 16/10/09]
I am glad this thread has been of use to people.
I thought I would add and update to the first page so people don't have to wade through the whole thread.
If you are experiencing this issue you have two choices:
1)CID unlock your Hero (http://forum.xda-developers.com/showthread.php?t=559806).
2)Use a Rebel II Sim.
OK there are three choices.
3) Use your Hero on an Orange contract for about three months then ring up Orange and ask them for a unlock code. They will charge about £20 for it and you may have to wait up to two weeks for em to send it.
C'est tout.
*********************************************************
[Update 24/10/09]
OK, after discussions and PM's on this thread I was advised to use the code I had previously bought with a different rom (when I first got my Hero tried it I was using the Orange stock rom then Modacos 2.3).
I just tested it now, took out my rebel sim put in the code and it works! I am currently using Modaco's 2.8.
Hope this helps.
I used http://hero.unlock-now.com/sim-unlock-HTC-Hero/ and the code worked for me. I did get my Hero within a few days of release. My work collegue also did the same with no problems.
What network do you use your hero on now?
hi i bought one locked to orange uk and unlocked it here
http://www.simunlock-htchero.com/buy.html
i received the code in 2 minutes and it worked, i use now Optimus in Portugal
Got my second one (for the wife) off eBay a week or two back. Poster claimed it was days old. Unlocked through htcunlock fine. Three sim seems to work better with Orange radio than the tmobile hero I purchased earlier.
Zuber
RetroFlux: I'm now on o2 after my unlock.
i'm getting the same thing with my orange locked hero, I have even tried a foreign sim as suggested. But does not seem to unlock with the correct unlock code. Is there a cable method for unlocking?
I have the same problem.
First case:
Turn on the phone with orange SIM card - everything works fine.
Turn on the phone with any other SIM card (I actually tried 3 other SIM card from 3 different providers). It asks unlock code. Enter unlock code I bought (actually any code containing 8 digits) it says "Network unlock successful." But after that it allow only emergency calls and if I try to make a call I see "Not registered in network" message. After reboot it asks unlock code again.
Second case:
If I do "restore to factory defaults" and turn it on the first time with my (no orange) SIM card, it asks unlock code I enter correct unlock code (salesman gave me one, and after that I also bought the same code in the Internet )
it hangs with phrase "Unlocking SIM card...". (Actually "turn off menu" works, I even can make an emergency call, but that is all I can get from it)
Also I noticed that in the first case there is strange line on the bottom of the screen (of the size of the notification bar).
I have tried different ROMS (original, rooted, latest, modacos) all the same. I also tried to downgrade radio firmware. I even tried all SIM cards I can obtain, the problem is obviously doesn't caused by SIM/Network incompatibility. Btw, my SIM card works OK in another HTC Hero (which was bought with my one).
I think it is problem with unlock procedure itself, not with code correctness. If wrong code entered it must say something like "wrong code", but for any 8 digit code it says "Network unlock successful". Is is the symptom! )
I do not know what to do further
I got a (UK) Orange Hero about 3 weeks ago from dial-a-phone. Unlocked it without a problem about a week later from:
http://hero.unlock-now.com/sim-unlock-HTC-Hero/
Took about 20 mins and worked 1st time. Now running with an UK O2 sim. Sorry!
As I mentioned above, while first boot with my local SIM card it hangs with "Unlocking SIM card..." message. At this time I see the following processes running.
Code:
# ps wwwwwww
PID USER VSZ STAT COMMAND
1 0 292 S /init
2 0 0 SW< [kthreadd]
3 0 0 SW< [ksoftirqd/0]
4 0 0 SW< [watchdog/0]
5 0 0 SW< [events/0]
6 0 0 SW< [khelper]
7 0 0 SW< [suspend]
8 0 0 SW< [early_suspend]
9 0 0 SW< [kblockd/0]
10 0 0 SW< [kmmcd]
11 0 0 SW< [btaddconn]
12 0 0 SW< [btdelconn]
13 0 0 SW< [kondemand/0]
14 0 0 SW< [qmi]
15 0 0 DW< [rpcrouter]
16 0 0 SW< [detection/0]
17 0 0 SW< [krpcserversd]
18 0 0 SW [pdflush]
19 0 0 SW [pdflush]
20 0 0 SW< [kswapd0]
21 0 0 SW< [aio/0]
22 0 0 SW< [panel_on/0]
23 0 0 SW< [cabc_work_q]
24 0 0 SW< [mtdblockd]
25 0 0 SW< [kadspd]
26 0 0 SW< [USB mass_storag]
27 0 0 SW< [synaptics_wq]
29 0 0 SW< [kstriped]
30 0 0 SW< [krfcommd]
31 0 0 SW< [mmcqd]
33 0 3328 S /sbin/adbd
50 1000 808 S /system/bin/servicemanager
51 0 852 S /system/bin/vold
52 0 668 S /system/bin/debuggerd
53 1001 11064 S /system/bin/rild
54 0 73504 S zygote /bin/app_process -Xzygote /system/bin --zygote --start-system-server
55 1013 30172 S /system/bin/mediaserver
57 1002 1180 S /system/bin/dbus-daemon --system --nofork
59 0 800 S /system/bin/installd
61 1008 1196 S /system/bin/akm8973
73 0 0 DW< [snd_rpc]
77 1000 173m S system_server
140 9998 159m S android.process.acore
142 1001 132m S com.android.phone
144 1000 96660 S com.htc.android.htcsetupwizard
166 10002 111m S com.google.process.gapps
179 0 0 DW< [ksdiorqd]
180 0 0 SW< [tiwlan_wifi_wq]
186 10004 96600 S com.htc.android.worldclock
193 10005 101m S com.htc.provider
207 1010 3160 S /system/bin/wpa_supplicant -Dtiwlan0 -itiwlan0 -c/data/misc/wifi/wpa_supplicant.conf
237 10031 121m S com.htc.android.htcime
244 9999 140m S com.htc.launcher
253 10016 98640 S com.htc.android.psclient
265 10017 107m S com.android.mms
285 10019 97736 S android.process.media
296 10020 106m S com.google.android.apps.maps:FriendService
307 10022 99016 S com.esmertec.android.jbed
322 10036 97.6m S com.google.android.partnersetup
332 10042 100m S com.htc.calendar
346 1000 100m S com.android.settings
356 10029 98612 S com.htc.android.footprints
366 10013 98012 S com.android.setupwizard
430 0 740 S /system/bin/sh -
468 0 2072 R ps wwwwwww
Im having the same issue, I got a new HTC Hero on Orange today, and it wont unlock. I used Unlock-now, so I have sent them a message asking for my money back, will that suffice. Has anyone been able to get there Orange UK, branded and locked phones unlocked.
nintendolinky, what is your ROM version ? There may be a possibility you have the latest firmware build... maybe...
i'm in the same boat! bought the code but no joy. it say's unlocked but could not register my voda sim. Anyone?
I tried to contact Orange today to buy an unlock code from them directly, after been passed about I eventually got through to someone bureaucratic wench who was completely unhelpful and I ended up telling them to F off and hung up. Kind of shot myself in the foot there.
I know this doesn't help our situation but I am still looking into it.
joemax said:
nintendolinky, what is your ROM version ? There may be a possibility you have the latest firmware build... maybe...
Click to expand...
Click to collapse
So are you saying there is an issue with the new firmware? When you say firmware do you mean ROM? As I have already flashed Modacos latest ROM and my Three/Vodafone/O2 sim still won't work.
I don't have my Hero with me at the moment but will post back my firmware number later, if other people (who are having the same issue) can post theirs maybe we can find a common firmware at fault.
nintendolinky said:
I used Unlock-now, so I have sent them a message asking for my money back, will that suffice.
Click to expand...
Click to collapse
I used Unlock-Now, they did refund me after your usual basic diagnostics.
joemax said:
nintendolinky, what is your ROM version ? There may be a possibility you have the latest firmware build... maybe...
Click to expand...
Click to collapse
Ok, here are my firmware details:
Firmware version: 1.5
Baseband Version: 63.18.55.06EU_6.35.06.18
Kernel Version: 2.6.27-8dd6deee [email protected]
Build Number: 2.73.405.5 146733 CL#61267 MCR2.2c release keys
Software Version: 1.0.0.A6288
Someone out there must be able to help fix this, pros/cooks/anyone can you shed anylight on this?
I've tried oldest/newes/custom ROMs, it looks like unlocking procedure doesn't depend on ROM at all.
is there a way to unlock this via cable? what about flashing the rom?
my build number is
Build Number: 1.76.61.3 whats the difference with this and Build Number: 2.73.405.5?
Here is my info:
Firmware version: 1.5
Baseband Version: 63.18.55.06EU_6.35.06.18
Kernel Version: 2.6.27-8dd6deee [email protected]
Build Number: 2.73.405.5 146733 CL#61267 MCR2.2e release keys
Software Version: 1.0.0.A6288
My build number is different, to the one listed here.
Hi Experts,
I have a following problem with glgps during the tests on the phone with MTK6577 platform with 4.0.4 ICS (Broadcom 4751 A2 as onboard GPS chip) :
When I start any navigation application I see the glgps crash with following messages in logs :
"
4:09:15.435 $651083I Write NVRAM Almanac SBAS 18
04:09:15.435 $651083I Write NVRAM Almanac SBAS 19
04:09:15.435 $651083N LTO_BAD(from Broadcast) { }
04:09:15.435 $651083N LTO_BAD(from HighResid) { }
04:09:15.436 Closed NVRAM file
04:09:15.436 $651084I GlChovyCtrl::SaveNvRamAndRtc(4979 225321 8978432, Invalid)
04:09:15.436 $651084I <GlMeasEng::SetNvmem>[snr=-1,Fail=F][bBinCtr=F/F][bBinDir=+/+]
04:09:15.437 $651085I NVRAM write complete (Clear 0x50000)
04:09:15.437 $651085I GlChovyCtrl::AsicToStandby()
04:09:15.437 $651085I PMM::me -LpEntry -sv(0>=7 -142dBm) && -pe
04:09:15.448 $651096I GlPosEng::AsicStopped()
04:09:15.448 $651096C ReloadComponents() PSF={DERATE_TIME 0x0 RECOVER_JOBS 0x0} Need={Reset 1 Restart 1} Abort 0
04:09:15.448 $651096C Abnormal GlEngine stop. Initial time estimate was bad
"
I searched anywhere but ... failed.
Have you any ideas ?
How to troubleshoot this issue ?
Is it the any misconfiguration in gpsconfig.xml or glgps daemon bug ?
I can send any diagnostics and configs
Thanks a lot for your response.
I have Just Diagnosed the Cause but not successful with any solid solution so far.
Similar problem i have with my MTK6575 smartphone (QMobile A6) , Problem is due to InCorrect calculation of Time by GlEngine when it is using NVRAM as timesource, GlEngine is neither using NTP Servers nor Cell Towers as timing source, it is only using either NVRAM time (Calculated) by default or GPS time (Download),
now if it using NVRAM as time source,
14:25:35.464 $081969I FixStatus: TimeSource 1
14:25:35.464 --GlPe_FixStatus::SetSIGMeasuement Setting utc time to 2012 (yr) 11 (mo) 25 (dt) 9 (hr) 5 (mn) 14 (sec) 565 (ms) 0 (us) 1000000 (prec)
It mostly Stops Abnormally. But on the next Startup, it resets it time to year 2007, and use GPS provided time as source.
21:56:02.218 $134952I FixStatus: TimeSource 0
21:56:02.218 --GlPe_FixStatus::SetSIGMeasuement Setting utc time to 2007 (yr) 3 (mo) 31 (dt) 23 (hr) 59 (mn) 58 (sec) 79 (ms) 0 (us) -1 (prec)
in that case it takes a little time but do not shutdown and using Supl Server it could easily locks and remain Locked but from next time it again use time stored in NVRAM as stored, which could again give similar result.
I did'nt see any configuration in GPSCONFIG.XML to use GPS satellites as default time source and ignore NVRAM stored time.
so the GlEngine (/system/bin/glgps) need modifications.
i have different GlEngines with no luck so far, if any one could understand the cause, plz Advise the Solution
Plz also see my article on XDA.
http://forum.xda-developers.com/showthread.php?p=35826094#post35826094
Hi,
I bought an Andorid media player. It isin't very clear who made it. It has a kingzer case but cannot find the case or any info on it on their website. It was made rooted I wanted to unroot it so I could run media apps properly. I then tried to install CWM spesifcally "CWM Recovery 6.0.1.2 for Allwinner A10 LY-F1/TREQ Tablets" thread on xda-developers. Its an Allwinner A10. So I got it to install but when I boot up my media box now I get CWM screen 4 times on my tv and its all pink saying
E: Can't mount /sdcard/
E: Can't mount /cache/recovery/command
E: Can't mount /cache/recovery/log
E: Can't open /cache/recovery/log
E: Can't mount /cache/recovery/last_log
E: Can't open /cache/recovery/last_log
The buttons on the front of my media box only move the selection up and down cannot actually "select" anything. I have tried ADB it appears as "20080411 recovery" however when I try to fastboot it and do fastboot devices nothing appears. Iv tried both windows 7 and Linux Mint. I have no idea what to do. Id rather not just throw it away as scrap cost me £100. Below are the specs I got from the device before hand.
Android version 4.0.4
Release Codename: REL
API LEVEL 15
CPU ABI armeabi-v7a
Manufacturer unknown
Bootloader unknown
CPU ABl2 armeabi
Hardware: sun4i
Radio unknown
Board crane
Brand softwinners
Device: apollo-zhpubhost
Display: apollo_zhpubhos-eng 4.0.4
Fingerprint softwiners/apollo_zhpubhos-eng 4.0.4/IMM76D/20121210:eng/test-keys
Host androidck-desktop
ID IMM76D
Model zhpubhost-A10-APOLLO
Product apollo_zhpubhost
Tags: test-keys
Type: eng
User androidck
Also not sure if this helps but by typing adb shell ps
PID USER VSZ STAT COMMAND
1 root 320 S /init
2 root 0 SW [kthreadd]
3 root 0 SW [ksoftirqd/0]
4 root 0 SW [kworker/0:0]
5 root 0 SW [kworker/u:0]
6 root 0 SW [rcu_kthread]
7 root 0 SW< [khelper]
8 root 0 SW< [netns]
9 root 0 SW< [suspend]
10 root 0 SW [sync_supers]
11 root 0 SW [bdi-default]
12 root 0 SW< [kintegrityd]
13 root 0 SW< [kblockd]
14 root 0 SW [khubd]
15 root 0 SW< [cpufreq_uevent]
16 root 0 SW< [cfg80211]
17 root 0 SW [kworker/0:1]
18 root 0 SW< [rpciod]
19 root 0 SW [kswapd0]
20 root 0 SWN [ksmd]
21 root 0 SW [fsnotify_mark]
22 root 0 SW< [nfsiod]
23 root 0 SW< [crypto]
37 root 0 SW [nandd]
38 root 0 SW [nfmtd]
39 root 0 SW [kworker/u:1]
46 root 0 SW< [f_mtp]
47 root 0 SW [file-storage]
48 root 0 SW [kworker/0:2]
49 root 0 SW< [kpsmoused]
50 root 0 DW [kinteractiveup]
51 root 0 SW< [kfantasy]
52 root 0 SW< [binder]
53 root 0 SW< [codec_resume]
54 root 0 SW< [krfcommd]
55 root 0 SW [hdmi proc]
56 root 312 S /sbin/ueventd
58 root 16536 S /sbin/recovery
64 root 4480 S /sbin/adbd recovery
104 root 1876 S /sbin/sh -c ps
106 root 1880 R ps
I got that. Any help wold be really appreciated. Thanks
Perhaps others can, but from what you have posted, I have no idea which box you have.
A picture of the device, and better yet, a picture of the circuit board may help.
Then perhaps someone on these forums can identify it and point you to a ROM (Firmware) that you can load.
Lots of these things are sold under different names, so installing a new firmware may "re-brand" it, but at least you'll (hopefully) have a working device.
Linuxslate said:
Perhaps others can, but from what you have posted, I have no idea which box you have.
A picture of the device, and better yet, a picture of the circuit board may help.
Then perhaps someone on these forums can identify it and point you to a ROM (Firmware) that you can load.
Lots of these things are sold under different names, so installing a new firmware may "re-brand" it, but at least you'll (hopefully) have a working device.
Click to expand...
Click to collapse
attached the picture of the motherboard and here is a link to the box on ebay - ebay - co uk - /itm/3D-Blu-Ray-3-5-HDD-MKV-Media-Player-MINI-PC-Android-4-0-TV-Box-DDR3-1GB-HDMI1-4-/170962126682?pt=UK_WSJL_Wholesale_GL&hash=item27ce23075a
not allowed to post outside links but its ebay its safe
If you could help me i would be grateful
Any help? I really don't know what to do. I don't want to throw away £100
Use PhoenixCard or Livesuit to reinstall stock firmware
diogo.c said:
Use PhoenixCard or Livesuit to reinstall stock firmware
Click to expand...
Click to collapse
Hi , i have same problems but i dont have a stock firmware whit itek itad002
some news or help me please
many thanks
Paolo
I have a Samsung S3 mini, which I flashed with Kit Kat Cyanogenmod 11.0 from novafusion.pl
Everything in the installation was OK.
However my phone randomly falls "sleep" and cannot recieve msgs or calls. I have to turned Airplane mode on and off, to give it a "shake" and "wake" it up.
These is a report from Logcat, plus the log from yesterday,
Code:
build.board: montblanc
build.bootloader: unknown
build.brand: samsung
build.cpu_abi: armeabi-v7a
build.cpu_abi2: armeabi
build.device: golden
build.display: cm_golden-userdebug 4.4.4 KTU84Q d39c1e8ca0 test-keys
build.fingerprint: samsung/cm_golden/golden:4.4.4/KTU84Q/d39c1e8ca0:userdebug/test-keys
build.hardware: samsunggolden
build.host: novafusion.pl
build.id: KTU84Q
build.manufacturer: samsung
build.model: GT-I8190
build.product: cm_golden
build.radio: unknown
build.serial: 47900592d6cb30c0
build.tags: test-keys
build.time: 1436279173000
build.type: userdebug
build.user: root
version.codename: REL
version.incremental: d39c1e8ca0
version.release: 4.4.4
version.sdk_int: 19
I can't attach my full log because I'm new on the forum.
This is the top 30 unique lines processed by me in Bash,
Code:
[email protected]:~/Dropbox# cat 2015-07-28-10-25-50.txt | grep " E/" | cut -d "/" -f 2- | sort | uniq -c | sort -rn | head -n 30
166 Drm ( 1669): Failed to open plugin directory /vendor/lib/mediadrm
144 SpannableStringBuilder( 4288): SPAN_EXCLUSIVE_EXCLUSIVE spans cannot have a zero length
118 ActivityThread( 2565): Failed to find provider info for com.google.android.wearable.settings
87 AuthorizationBluetoothService( 2483): Proximity feature is not enabled.
85 ConnectivityService( 2088): Can't set delayed ACK size:java.io.FileNotFoundException: /sys/kernel/ipv4/tcp_use_userconfig: open failed: ENOENT (No such file or directory)
85 ConnectivityService( 2088): Can't set delayed ACK size:java.io.FileNotFoundException: /sys/kernel/ipv4/tcp_delack_seg: open failed: ENOENT (No such file or directory)
70 audio_a2dp_hw( 1669): adev_set_parameters: ERROR: set param called even when stream out is null
59 WifiNative-wlan0( 2088): doBoolean: disable
57 WifiNative-wlan0( 2088): doBoolean: enable
49 CallDetails( 2409): list is null in setConfUriList
48 ActivityThread(14438): Failed to find provider info for com.google.android.wearable.settings
31 MDM ( 2388): [64] b.run: Couldn't connect to Google API client: ConnectionResult{statusCode=API_UNAVAILABLE, resolution=null}
31 BluetoothPhoneService( 2409): Could not get a handle on Connection object for the call
30 MDM ( 2388): [89] b.run: Couldn't connect to Google API client: ConnectionResult{statusCode=API_UNAVAILABLE, resolution=null}
26 MDM ( 2388): [67] b.run: Couldn't connect to Google API client: ConnectionResult{statusCode=API_UNAVAILABLE, resolution=null}
25 LocationReceiver( 6879): Received bad location: null
17 ENSWrapper( 1673): return OMX_ErrorNotImplemented - GetExtensionIndex OMX.ST.AFM.pcmprocessing.spl h=0x414b3f80 cParameterName=STE.ADM IndexType=unknown OMX_INDEXTYPE [ 0x4d2efb3e ]
16 SpannableStringBuilder(25691): SPAN_EXCLUSIVE_EXCLUSIVE spans cannot have a zero length
15 YSNP_TAG( 5072): [NetworkHelper] : [thread:1]checkNetworkChange() - no active network!
14 bp ( 2374): onStartInput event aborted: com.touchtype.keyboard.c.ag: could not obtain extracted text (class com.touchtype.keyboard.c.ag)
13 ENSWrapper( 1673): return OMX_ErrorNotImplemented - GetExtensionIndex OMX.ST.AFM.pcmprocessing.spl h=0x411acd98 cParameterName=STE.ADM IndexType=unknown OMX_INDEXTYPE [ 0x4d2efb3e ]
11 ENSWrapper( 1673): return OMX_ErrorNotImplemented - GetExtensionIndex OMX.ST.AFM.pcmprocessing.spl h=0x4161b3a0 cParameterName=STE.ADM IndexType=unknown OMX_INDEXTYPE [ 0x4d2efb3e ]
9 ENSWrapper( 1673): return OMX_ErrorUnsupportedIndex - SetConfig OMX.ST.AFM.speech_proc h=0x419f8f40
9 ENSWrapper( 1673): return OMX_ErrorUnsupportedIndex - SetConfig OMX.ST.AFM.speech_proc h=0x416a0f08
9 ENSWrapper( 1673): return OMX_ErrorUnsupportedIndex - SetConfig OMX.ST.AFM.speech_proc h=0x41490f68
9 ENSWrapper( 1673): return OMX_ErrorUnsupportedIndex - SetConfig OMX.ST.AFM.speech_proc h=0x412c9f58
9 ENSWrapper( 1673): return OMX_ErrorUnsupportedIndex - SetConfig OMX.ST.AFM.speech_proc h=0x412c8f48
8 VFM ( 1669): ! getSupportedVideoSettings RETURN_XXX_IF_WRONG, condition=(index<mNbVideoSettingsSupported[nPortIndex]), error=-2147479538(0x8000100e)(OMX_ErrorNoMore) /home/se.infra/jenkins1/workspace/HUDSON_GA_JELLYBEAN_GOLDEN_EUROPEN-PROD-XX/android/vendor/st-ericsson/variant/multimedia/video/vfm/src/VFM_Component.cpp:407
8 VFM ( 1669): ! getSupportedProfileLevel RETURN_XXX_IF_WRONG, condition=(index<mNbProfileLevelSupported), error=-2147479538(0x8000100e)(OMX_ErrorNoMore) /home/se.infra/jenkins1/workspace/HUDSON_GA_JELLYBEAN_GOLDEN_EUROPEN-PROD-XX/android/vendor/st-ericsson/variant/multimedia/video/vfm/src/VFM_Component.cpp:379
8 VFM ( 1669): ! getParameter RETURN_OMX_ERROR_IF_ERROR, condition=pParam->getIndexParamVideoProfileLevelQuerySupported(pt), error=-2147479538(0x8000100e)(_error) /home/se.infra/jenkins1/workspace/HUDSON_GA_JELLYBEAN_GOLDEN_EUROPEN-PROD-XX/android/vendor/st-ericsson/variant/multimedia/video/vfm/src/VFM_Component.cpp:140
carlosalomar said:
I have a Samsung S3 mini, which I flashed with Kit Kat Cyanogenmod 11.0 from novafusion.pl
Everything in the installation was OK.
However my phone randomly falls "sleep" and cannot recieve msgs or calls. I have to turned Airplane mode on and off, to give it a "shake" and "wake" it up.
These is a report from Logcat, plus the log from yesterday,
I can't attach my full log because I'm new on the forum.
This is the top 30 unique lines processed by me in Bash
Click to expand...
Click to collapse
Hi, you might get better results asking in your specific device help forum.
http://forum.xda-developers.com/galaxy-s3-mini/help
Good luck!
Hi, I've recently managed to install android x86 8.1 r5 on my Dell Latitude E6530 and got video out through HDMI to TV using LVDS-1:d via grub.
However I'm unable to get audio through HDMI.
Can anyone tell me why?
Here is what I get on terminal:
x86_64:1 $ su
x86_64:7 # cat /proc/asound/cards
0 [PCH ]: HDA-Intel - HDA Intel PCH
HDA Intel PCH at 0xf7e30000 irq 30
X86_64:/ # ls -l /dev/snd
total 0
cru-rw--- 1 system audio 116, 5 2020-08-07 00:49 controlC0
crw-rw---- 1 system audio 116, 4 2020-08-07 00:49 hwC0D0
crw-rw---- 1 system audio 116, 3 2020-08-07 00:49 pcmC0D0c
crw-rw---- 1 system audio 116, 2 2020-08-07 00:49 pcmC0D0p
crw-rw---- 1 system audio 116, 33 2020-08-07 00:49 timer
Noone has a knowledge on how to fix this?
Hi guys,
I also have same problem with "relic".
No audio on Hdmi.
My system is i3, 4Mb ram, 240 Gb ssd, ( Asus VivoPC V60).
Can anyone help us about it, please ?