Ok, so I installed a ROM which lead to my phone being stuck in BootLoop. I wiped my cache using fastboot on my PC and I can now enter recovery again. My phone is recognized by my computer and shows that it is connected in both fastboot and adb. Whenever I try to push or sideload a new ROM it just stays at 1% and does nothing?
any help would be appreciated I just need to sideload or push a new rom to my phone so I can flash it. Thanks
Related
I was on Neutrino 2.5, I flashed to 2.5p (without wiping).
It wasn't working as I wanted so I went in to recovery to reflash the google apps zip.
After that I'm now stuck in a boot cycle loop and I can't even boot in to recovery mode. When I try to enter recovery it says "Entering Android Recovery Mode" then the screen just goes blank.
Really sorry to make this my first post but I'm kinda freaking out right now. Don't have any idea how to recover from this.
rodabi said:
I was on Neutrino 2.5, I flashed to 2.5p (without wiping).
It wasn't working as I wanted so I went in to recovery to reflash the google apps zip.
After that I'm now stuck in a boot cycle loop and I can't even boot in to recovery mode. When I try to enter recovery it says "Entering Android Recovery Mode" then the screen just goes blank.
Really sorry to make this my first post but I'm kinda freaking out right now. Don't have any idea how to recover from this.
Click to expand...
Click to collapse
flash the recovery again using fastboot
Thanks for the reply. So my problem so is that I'm trying to boot in to RSD mode but it get the message "Battery is too low to flash".
I'm trying to charge the battery but whenever i plug it in to charge phone starts up and ends up in the boot cycle, and the battery doesn't end up charging.
How can i force the phone not to turn on when I plug it in to the wall charger?
Ok, I was able to McGyver a usb charger from an old cable and I got the battery charged enough where it would enter fastboot.
However... now I can't get either of my laptops to recognize the phone in fastboot.
I attach the phone to the usb port, turn the phone on and hold the volume down button. I press the volume up button when fastboot appears, the message "Starting Fastboot protocol support" appears and then nothing happens. Windows just sits there, the phone just sits there...
If I do moto-fastboot devices at the command prompt there is no serial.
Any thoughts?
Well, normally nothing happens until you issue a fastboot command. I usually boot into fastboot mode first, THEN connect the phone & open a command line, etc.
What happens if you do the above and type "fastboot devices"? Does it see your phone then?
Ok, so I tried your method, and installing some different windows drivers and now windows does recognize the phone!
For the record, I am on windows xp and currently i'm using driver version 2.0.40 (same problem with 2.0.53).
Now windows isn't able to install the fastboot drivers, it comes up as an unrecognized device. Is there a way to manually install the fastboot drivers?
Although it's recognized by windows, issuing the moto-fastboot devices command still returns blank.
my device is always booting to fastboot and shows me only a blank screen
i was running android 2.3
i tried to install clockworkmod recovery and i lost my all recovery
then i tried to install twrp recovery trough adb and after that my device went to fastboot and now my device is always at fastboot
i can pull the battery out because its like that like iphone
fastboot commands are working and my android is identified by pc
can you please help me to get my device back to working condition
thanks
my zen6 can boot up normally but i cant boot into recovery. I try using volup+power up button but the phone black screen after it vibrate and show the asus logo...Here what i already try a method :
1.Using adb reboot recovery but goes same result
2.using apps (rom manager/busybox) also got the same thing
I still can boot into bootloader using adb reboot-bootloader command from adb but my computer didnt detect it...i have all the driver install but still cant detect it...already try using different computer but also cant detect it...i try to reinstall all the driver but goes to the same result too...i cant even flash a stock recovery using fastboot flash recovery command...it stuck at "waiting for device" ....
try to factory reset from the setting but it go same like when i try to boot into recovery...
Any ideas of how to solve this problem...i cant perform any update on my phone because of this....
Hi:
My unlocked bootloader SS2 phone got stucked in Download Mode after successfully installed/flashed AICP ROM
It booted once and when i rebooted to enter recovery got stucked. Tried pushing buttons combos but still stucked in Dmode.
Have no access to fastboot from Windows but can get limited access to fastboot in Debian: can flash several twrp recoveries, can flash
AICP ROM again but can not get fastboot oem commands working.
Can't enter to recovery because phone never turn off.
Tried also to come back to Nougat but can't enter recovery to flash ss2_old_bootloader.
I do not know what to do.
Any help?
Also have this problem... any help?
have u try to connect into computer, use adb, and use this command :
Code:
fastboot reboot
what's the result with that?
No connection.
But i have reinstalled OST Treble ROM and phone now working.
gsausalito said:
Hi:
My unlocked bootloader SS2 phone got stucked in Download Mode after successfully installed/flashed AICP ROM
It booted once and when i rebooted to enter recovery got stucked. Tried pushing buttons combos but still stucked in Dmode.
Have no access to fastboot from Windows but can get limited access to fastboot in Debian: can flash several twrp recoveries, can flash
AICP ROM again but can not get fastboot oem commands working.
Can't enter to recovery because phone never turn off.
Tried also to come back to Nougat but can't enter recovery to flash ss2_old_bootloader.
I do not know what to do.
Any help?
Click to expand...
Click to collapse
I also have problem after flashing to AICP and sometimes phone (after power off) stuck in Download mode.
Just enter:
fastboot --set-active=a reboot
rgr1 said:
I also have problem after flashing to AICP and sometimes phone (after power off) stuck in Download mode.
Just enter:
fastboot --set-active=a reboot
Click to expand...
Click to collapse
I have the same problem. I tried to follow your advice, but fastboot in my PC doesn't recognize the parameter (all I get is fastboot help page).
Regards.
EDIT: reinstalled treble v3.1 via OST and it fixed the download mode issue.
thanks!
hi,
got the same problem, stuck at download mode but phones can`t to pc via usb so I am unable to use fastreboot.
Any other suggestions how to fix it ?
internety1 said:
hi,
got the same problem, stuck at download mode but phones can`t to pc via usb so I am unable to use fastreboot.
Any other suggestions how to fix it ?
Click to expand...
Click to collapse
in my xperience is connect your phone to the PC then open cmd ... make sure in folder of adb and fastboot .exe stored ...
type:
Code:
fastboot continue
longu said:
I have the same problem. I tried to follow your advice, but fastboot in my PC doesn't recognize the parameter (all I get is fastboot help page).
Regards.
EDIT: reinstalled treble v3.1 via OST and it fixed the download mode issue.
Click to expand...
Click to collapse
Maybe use other fastboot.
Sometimes you must enter:
Code:
fastboot --set-active=_a reboot
("_a" instead of "a")
BTW. My Aquos sometimes stuck in download mode after installing AICP.
I fixed this by entering:
Code:
adb shell
bootctl mark-boot-successful
Hello, i have the same exact problem. I tried to use adb program to fix this problem, but my laptop couldn't recognize my device. Any other solutions would be helpful. Thanks for your attention! (I'm a beginner in technology, so please forgive me)
Hello all,
I am stuck in this problem. Would appreciate any help.
Working in LINUX ubuntu 18.
Got a MI pad 1 with locked bootloader.
flashed TWRP recovery using fastboot. Booted into TWRP successfully.
Flashed the files from this
https://www.techeia.com/2018/10/best-custom-rom-for-mi-pad-1-2018.html
Everything flashed successfully.
Rebooted only to be stuck into MI logo screen. Bootloop probably because of locked bootloader.
Hence, I decided to wipe the bootloader itself
got the hint from here https://forum.xda-developers.com/mi-pad/how-to/fix-fastboot-bootloop-fix-xiaomi-mi-pad-t4008653
but I didn,t wiped recovery. but erased everything else. Then powered off to boot into previously installed TWRP recovery.
From there, I am trying to boot into fastboot or TWRP but the screen is showing blank. I am using the key pattern for fastboot or recovery and trying to detect the device into any mode through ubuntu terminal using
sudo fastboot devices and
adb devices
but its not detecting the device there also. USB debugging was enabled already.
Any clues for how can I boot into fastboot or TWRP from this.
Regards
Hiteshkartik
@hiteshkartik
A device with erased boot-loader never can work: you simly get a black screen. You no longer can communicate with it - neither via ADB nor via Fastboot.
Can I have a way around ?? I mean installing bootloader or somehow booting into fastboot or TWRP directly with any toolkit or terminal.