Hello everyone, i am facing a great wall of desperation, i woke up today to find my mobile stuck on samsung logo, and i noticed it's not responding, i booted to my CWM recovery and it kept generating these errors :
E:can't mount /cache/recovery/command
E: can't mount /cache/recovery/log
E: open /cache/recovery/log
E:can't mount /cache/recovery/last_log
E: can't open /cache/recovery/last_install
E: can't mount /cache/recovery/last_install
i tried wiping data but keeps generating same errors to the internal SD card with a unique error : E:format_volume: make_extf4fs failed on /dev/block/mmcblk0p8 .
i looked for a custom recovery file that i can install using ODIN but they're all in .img form not .tar.md5 so i didn't know what to do with them, phone doesn't recognize .img to install directly from sd card.:crying:
i tried using odin to install custom recovery tar.md5 file but didn't fix anything,
i tried installing this rom ( http://forum.xda-developers.com/galaxy-s3/development/rom-archidroid-v2-4-6-power-hands-t2354859 ) using the ( mount external sd card ) and transfering rom zip file and installing it via CWM recovery interface, the installation was succesful but still can't boot due to the mentioned errors .
i tried using ABD thingie but for somereason it just won't recognize my phone, while odin does, i tried installing and reinstalling samsung usb driver and ABD drivers but still didn't help,
my original ROM was CM 11.2 nightly.
please help i am desperate, i searched everywhere but there's always something that falls between my steps .
i am more than happy to get assistance via skype etc.
i managed to download and flash my phone with stock 4.3, but i am still facing same problem, stuck at samsung logo and same errors in CWM recovery .
Same problem
i think we might have the same problem.
samdroid posted a possible solution in my thread maybe try that?
http://forum.xda-developers.com/galaxy-s3/help/samsung-i9300-wont-pass-boot-t2809239
Sporedd66 said:
i think we might have the same problem.
samdroid posted a possible solution in my thread maybe try that?
http://forum.xda-developers.com/galaxy-s3/help/samsung-i9300-wont-pass-boot-t2809239
Click to expand...
Click to collapse
but i can't find a thread or forum section dedicated to cm 11 !
update: i was able to access ABD command line, i tested 3 CWM recovery .img files and all 3 of them reported as (bad) by my phone .
Could be bad eMMC. If you want to be sure try flash the rescue firmware from this thread (with pit) http://forum.xda-developers.com/showpost.php?p=30087735&postcount=6
If it's still not working it's a hardware fault.
DrFredPhD said:
Could be bad eMMC. If you want to be sure try flash the rescue firmware from this thread (with pit) http://forum.xda-developers.com/showpost.php?p=30087735&postcount=6
If it's still not working it's a hardware fault.
Click to expand...
Click to collapse
thank you for the suggestion, i am downloading it as we speak, i sure hope it's not physical brick, i really can't afford buying new phone atm....
DrFredPhD said:
Could be bad eMMC. If you want to be sure try flash the rescue firmware from this thread (with pit) http://forum.xda-developers.com/showpost.php?p=30087735&postcount=6
If it's still not working it's a hardware fault.
Click to expand...
Click to collapse
after multiple tries, it didn't work, the installation won't even initialize, it keeps saying FAIL
please anyone...help !!!!
If you're still in warranty send it in for repair. Sometimes eMMC will fail and download mode will say custom even if phone has never been flashed so they might repair it for you.
DrFredPhD said:
If you're still in warranty send it in for repair. Sometimes eMMC will fail and download mode will say custom even if phone has never been flashed so they might repair it for you.
Click to expand...
Click to collapse
it's been long since off warranty, if there's a fix it has to be something i can do myself, sending it for repair is out of the question .
Rom
simlol12 said:
please anyone...help !!!!
Click to expand...
Click to collapse
Meanwhile download CFAutoroot and make the recovery of stoock and see if there is recovery. After you find MK6 Factory with BL,AP,CSC,Modem, separated and with odin 3.9 to install and i hope that you have data backup because this eliminates everything. If this succeeds you should do restore the folders EFS. I hope that you can help if you have any problems finding the material send me a private message that I see if I can upload them to mega .
Related
I think my phone is dead. Need help bad.
I went to flash gapps 20121011 in recovery. When recovery loaded I saw this:
E:can't open /cache/recovery/log
E:can't open /cache/recovery/log
E:can't open /cache/recovery/log/last_log
E:can't open /cache/recovery/log/last_log
I didn't take much notice. I went on to install gapps 20121011 and the phone restarted. Resurrection logo (Custom ROM I am using) kept on loading. I went back to recovery and I couldn't wipe the cache, it would freeze.
I tried to mount EMMC and I get this: E:can't mount /emmc/
I tried reflashing the ROM, but it got stuck on 50% in AROMA installation. Stayed like that for a very long time before I turned the phone off.
I then tried to use Odin to flash a stock ROM via download mode, Odin recognised my phone and when I started it, nothing would happen, it will just stall
Then when I turned my phone off after waiting for a long time, I get this message with a yellow triangle in the middle and 2 computers side by side: Firmware upgrade encountered an issue. Please select recovery mode in Kies.
Every time I turn off and on my phone I get that message.
I have a USB jig and can get into download mode. Nothing seems to work.
Please, I really appreciate the help here. How can I get this phone to work again?
justmiike said:
I think my phone is dead. Need help bad.
I went to flash gapps 20121011 in recovery. When recovery loaded I saw this:
E:can't open /cache/recovery/log
E:can't open /cache/recovery/log
E:can't open /cache/recovery/log/last_log
E:can't open /cache/recovery/log/last_log
I didn't take much notice. I went on to install gapps 20121011 and the phone restarted. Resurrection logo (Custom ROM I am using) kept on loading. I went back to recovery and I couldn't wipe the cache, it would freeze.
I tried to mount EMMC and I get this: E:can't mount /emmc/
I tried reflashing the ROM, but it got stuck on 50% in AROMA installation. Stayed like that for a very long time before I turned the phone off.
I then tried to use Odin to flash a stock ROM via download mode, Odin recognised my phone and when I started it, nothing would happen, it will just stall
Then when I turned my phone off after waiting for a long time, I get this message with a yellow triangle in the middle and 2 computers side by side: Firmware upgrade encountered an issue. Please select recovery mode in Kies.
Every time I turn off and on my phone I get that message.
I have a USB jig and can get into download mode. Nothing seems to work.
Please, I really appreciate the help here. How can I get this phone to work again?
Click to expand...
Click to collapse
as u said u can get into Dwnld mode using an USB jig, if so then try flashing a stock ics 4.0.3 rom pertained to ur region in ODIN by dwnld'ng the same from www.sammobile.com and see
Sun90 said:
as u said u can get into Dwnld mode using an USB jig, if so then try flashing a stock ics 4.0.3 rom pertained to ur region in ODIN by dwnld'ng the same from www.sammobile.com and see
Click to expand...
Click to collapse
Does it make a difference if it's ICS? I was trying to use Odin to flash stock GB version which is pretty old and it didn't work, just did nothing and stalled.
I'm downloading stock ICS as we speak. It's 717MB.
justmiike said:
Does it make a difference if it's ICS? I was trying to use Odin to flash stock GB version which is pretty old and it didn't work, just did nothing and stalled.
I'm downloading stock ICS as we speak. It's 717MB.
Click to expand...
Click to collapse
There should be no difference. If GB doesn't work your only choice is ICS. Don't flash 4.0.4 just to stay safe
Sent from my GT-I9100 using xda app-developers app
Tried to flash ICS and this time I get a hint of green bar progress but stalls at cache.img. So far 25 minutes with no progress.
GB stalled on NAND Write Start!! which is the next one up.
Is it screwed?
justmiike said:
Tried to flash ICS and this time I get a hint of green bar progress but stalls at cache.img. So far 25 minutes with no progress.
GB stalled on NAND Write Start!! which is the next one up.
Is it screwed?
Click to expand...
Click to collapse
There is some hope. Try to get help in existing threads: forum.xda-developers.com/showthread.php?t=1449771 and forum.xda-developers.com/showthread.php?t=1667886. Do not do anything before some knowledgeable guy give you some advice.
Do u have killed all Kies Background processes before try to Flash with odin?
Gesendet von meinem GT-I9100 mit Tapatalk 2
I haven't got Kies installed on my computer.
pilgrim011 said:
There is some hope. Try to get help in existing threads: forum.xda-developers.com/showthread.php?t=1449771 and forum.xda-developers.com/showthread.php?t=1667886. Do not do anything before some knowledgeable guy give you some advice.
Click to expand...
Click to collapse
I wrote in forum.xda-developers.com/showthread.php?t=1449771
Some posters have the same issue as me but getting no responses.
justmiike said:
I haven't got Kies installed on my computer.
Click to expand...
Click to collapse
You should have the correct drivers installed right? You can try installing kies again and this time make sure everything has been installed correctly.
Sent from my GT-I9100 using xda app-developers app
preseodymium said:
You should have the correct drivers installed right? You can try installing kies again and this time make sure everything has been installed correctly.
Click to expand...
Click to collapse
I installed Kies when I first got the phone and installed the correct drivers.
Then I uninstalled Kies but the correct drivers remained.
Odin recognises my phone (becomes yellow, which indicates drivers are installed) and stops at a certain point. I am pretty sure if Odin recognises my phone correct drivers are installed.
Sounds like a nad usb connection to me. Try Odin with a different usb port on your pc. Or a different computer.
Sent from my SGH-I747 using xda premium
skrambled said:
Sounds like a nad usb connection to me. Try Odin with a different usb port on your pc. Or a different computer.
Click to expand...
Click to collapse
I did try different USB ports, same result.
Currently the same results happen here at work too. Doesn't make sense.
justmiike said:
I think my phone is dead. Need help bad.
I went to flash gapps 20121011 in recovery. When recovery loaded I saw this:
E:can't open /cache/recovery/log
E:can't open /cache/recovery/log
E:can't open /cache/recovery/log/last_log
E:can't open /cache/recovery/log/last_log
I didn't take much notice. I went on to install gapps 20121011 and the phone restarted. Resurrection logo (Custom ROM I am using) kept on loading. I went back to recovery and I couldn't wipe the cache, it would freeze.
I tried to mount EMMC and I get this: E:can't mount /emmc/
I tried reflashing the ROM, but it got stuck on 50% in AROMA installation. Stayed like that for a very long time before I turned the phone off.
I then tried to use Odin to flash a stock ROM via download mode, Odin recognised my phone and when I started it, nothing would happen, it will just stall
Then when I turned my phone off after waiting for a long time, I get this message with a yellow triangle in the middle and 2 computers side by side: Firmware upgrade encountered an issue. Please select recovery mode in Kies.
Every time I turn off and on my phone I get that message.
I have a USB jig and can get into download mode. Nothing seems to work.
Please, I really appreciate the help here. How can I get this phone to work again?
Click to expand...
Click to collapse
Can you get into recovery?
Can you get to mounts and storage?
If so I have got out of a few sticky situations by:
*Go to mounts and storage and format cache, system, data and internal SD card. (Gives you a nice clean slate)
*Connect to Odin and flash a complete 4.0.3 firmware package that includes CSC, ROM and Modem.
Obagleyfreer said:
Can you get into recovery?
Can you get to mounts and storage?
Click to expand...
Click to collapse
I can't get into recovery anymore. Just download mode.
Hi guys,
Thanks for all your assistance.
I tried all the methods listed here on another computer: http://forum.xda-developers.com/showthread.php?t=1449771
The last step was to .PIT and Re-Partition. I did that and now the phone is dead. Won't boot up. I have no USB Jig here, but a repair center is close by.
I gave them the phone now and let them deal with it.
I'm pretty sure they will offer a replacement as I have nooo idea what they would do that I would have done different. I tried almost everything.
Hi Guys, hope someone can help. Ive been trawling the forums for days with no luck. I have a UK GT-I9300 on 4.1.2 rooted and with custom recovery. I installed cyanagen 10.1 but failed to wipe data / cache afterwards and now get stuck at galaxy flash screen everytime it boots. I can get to custom recovery and download screens, ive tried re-partitoning with pit file but the rom always get stuck at nand write stage. it appears that the phone is now "read only". this is really doing my head in so if any one can help i'd be really grateful.
cant mount /cache/recovery/command
cant mount /cache/recovery/log
cant open /cache/recovery/log
cant mount /cache/recovery/last_log
cant open /cache/recovery/last_log
not sure if this has anything to do with it.
Pit repartition Read \Only stuck at Nand al reads as a buggered nand and needs replacement motherboard .
jje
JJEgan said:
Pit repartition Read \Only stuck at Nand al reads as a buggered nand and needs replacement motherboard .
jje
Click to expand...
Click to collapse
feared as much, thanks for the quick response, of the service centre I go! Any idea how much this is gonna cost me?
Hi, I'm new to these forums and need some help!
I just rooted my Samsung Galaxy S3 i9300 yesterday using the Odin ver 1.85 tool and it was working perfectly all day. I was doing a little research as to how you can use custom ROMs and so I decided to give it a try.
I downloaded the ROM Manager application and flashed the ClockworkMod Recovery that comes with it before attempting to flash a ROM. I then proceeded to download the CyogenMod ver. 9.1.0 that comes with ROM Manager as well. I made sure to make a backup of my current ROM on both my internal and external SD cards and then went ahead and flashed the Cyogen ROM using the application. I also chose to wipe the data/factory reset before confirming.
After the process was done, the phone rebooted with the Cyogen logo and it was all working fine for the first 2 minutes. Then all of a sudden while going through the new ROM's screens, my phone rebooted showing the "Samsung GALAXY S III GT-I9300" message and with a little red "!" mark on the top left. It stays like that all the time. I tried turning the power off and taking out the battery but it always goes back to that screen immediately after.
I'm able to go into the ClockworkMod recovery by holding the volume up+power+home buttons but I see the following lines below:
ClockworkMod Recovery v6.0.3.2
E: Can't mount /cache/recovery/command
E: Can't mount /cache/recovery/log
E: Can't open /cache/recovery/log
E: Can't mount /cache/recovery/last_log
E: Can't open /cache/recovery/last_log
I've tried wiping the cache, wipe data/factory reset, and wiping the dalvik cache options but it doesn't seem to work. I also tried flashing the ROM again from the SD card, but when I try to do it, it says "E: Can't mount /sdcard/". Same thing with my external SD card.
When I plug the phone to my computer, it doesn't seem to detect my device either. Is my phone bricked and will I have to get a new one if this is the case?
I tried to do some searching and this thread seems to be similar to what I'm facing but not quite as the methods suggested by the users are unknown to me: http://forum.xda-developers.com/showthread.php?t=1500947
I appreciate any help I can get!
Zernell said:
Hi, I'm new to these forums and need some help!
I just rooted my Samsung Galaxy S3 i9300 yesterday using the Odin ver 1.85 tool and it was working perfectly all day. I was doing a little research as to how you can use custom ROMs and so I decided to give it a try.
I downloaded the ROM Manager application and flashed the ClockworkMod Recovery that comes with it before attempting to flash a ROM. I then proceeded to download the CyogenMod ver. 9.1.0 that comes with ROM Manager as well. I made sure to make a backup of my current ROM on both my internal and external SD cards and then went ahead and flashed the Cyogen ROM using the application. I also chose to wipe the data/factory reset before confirming.
After the process was done, the phone rebooted with the Cyogen logo and it was all working fine for the first 2 minutes. Then all of a sudden while going through the new ROM's screens, my phone rebooted showing the "Samsung GALAXY S III GT-I9300" message and with a little red "!" mark on the top left. It stays like that all the time. I tried turning the power off and taking out the battery but it always goes back to that screen immediately after.
I'm able to go into the ClockworkMod recovery by holding the volume up+power+home buttons but I see the following lines below:
ClockworkMod Recovery v6.0.3.2
E: Can't mount /cache/recovery/command
E: Can't mount /cache/recovery/log
E: Can't open /cache/recovery/log
E: Can't mount /cache/recovery/last_log
E: Can't open /cache/recovery/last_log
I've tried wiping the cache, wipe data/factory reset, and wiping the dalvik cache options but it doesn't seem to work. I also tried flashing the ROM again from the SD card, but when I try to do it, it says "E: Can't mount /sdcard/". Same thing with my external SD card.
When I plug the phone to my computer, it doesn't seem to detect my device either. Is my phone bricked and will I have to get a new one if this is the case?
I tried to do some searching and this thread seems to be similar to what I'm facing but not quite as the methods suggested by the users are unknown to me: http://forum.xda-developers.com/showthread.php?t=1500947
I appreciate any help I can get!
Click to expand...
Click to collapse
put your phone to download mode and flash rom with odin.
That should fix it.
austibor said:
put your phone to download mode and flash rom with odin.
That should fix it.
Click to expand...
Click to collapse
How can he do that?
Sent from my GT-I9300 using Tapatalk 2
rootSU said:
How can he do that?
Click to expand...
Click to collapse
power off the phone than hold power + menu + down key till you get to download mode.
than connect USB to pc run odin and flash a rom of your choice.
austibor said:
power off the phone than hold power + menu + down key till you get to download mode.
than connect USB to pc run odin and flash a rom of your choice.
Click to expand...
Click to collapse
Thanks this post should be a sticky .
jje
Thanks for the responses!
I tried to flash the i9300 firmware using Odin as suggested but it failed during the process (attached screen shot). I tried doing this 2 or 3 times but I always got the FAIL message. Is there anything else I can try doing before giving up on my phone? Maybe I flashed the wrong file?
Zernell said:
Thanks for the responses!
I tried to flash the i9300 firmware using Odin as suggested but it failed during the process (attached screen shot). I tried doing this 2 or 3 times but I always got the FAIL message. Is there anything else I can try doing before giving up on my phone? Maybe I flashed the wrong file?
Click to expand...
Click to collapse
Hmm not an expert here but can you try to check the "Re-Partition" checkbox
take your sdcard out, it should not matter but just in case
austibor said:
Hmm not an expert here but can you try to check the "Re-Partition" checkbox
take your sdcard out, it should not matter but just in case
Click to expand...
Click to collapse
If you're not an expert, please don't make suggestions.
Re-partition bricks the s3. I understand its semi bricked now but there is no return from re-partition.
Sent from my GT-I9300 using Tapatalk 2
---------- Post added at 07:45 AM ---------- Previous post was at 07:43 AM ----------
Zernell said:
Thanks for the responses!
I tried to flash the i9300 firmware using Odin as suggested but it failed during the process (attached screen shot). I tried doing this 2 or 3 times but I always got the FAIL message. Is there anything else I can try doing before giving up on my phone? Maybe I flashed the wrong file?
Click to expand...
Click to collapse
You're system partition looks broken. What info does it say on the screen in download mode
Sent from my GT-I9300 using Tapatalk 2
rootSU said:
You're system partition looks broken. What info does it say on the screen in download mode
Sent from my GT-I9300 using Tapatalk 2
Click to expand...
Click to collapse
When I enter download mode on the top left it says:
Odin Mode
Product Name: GT-I9300
Custom Binary Download: Yes (1 counts)
Current Binary: Custom
System Status: Custom
austibor said:
Hmm not an expert here but can you try to check the "Re-Partition" checkbox
take your sdcard out, it should not matter but just in case
Click to expand...
Click to collapse
Expert sir you are a positive danger .
jje
Zernell said:
When I enter download mode on the top left it says:
Odin Mode
Product Name: GT-I9300
Custom Binary Download: Yes (1 counts)
Current Binary: Custom
System Status: Custom
Click to expand...
Click to collapse
OK we can rule out SDS at least....
The firmware you have tried to flash is the leak. Try the official firmware from http://forum.xda-developers.com/showthread.php?t=1646610
It might help, not sure
mikep99 said:
The firmware you have tried to flash is the leak. Try the official firmware from http://forum.xda-developers.com/showthread.php?t=1646610
It might help, not sure
Click to expand...
Click to collapse
Sorry if this is a dumb question, but how do I know which firmware out of the ones from the list on that thread should I use? Does it matter?
Zernell said:
Sorry if this is a dumb question, but how do I know which firmware out of the ones from the list on that thread should I use? Does it matter?
Click to expand...
Click to collapse
Doesnt matter - try EME2 that's in the first post.
You will probably end up with an ODIN fail again but its worth trying...
mikep99 said:
The firmware you have tried to flash is the leak. Try the official firmware from http://forum.xda-developers.com/showthread.php?t=1646610
It might help, not sure
Click to expand...
Click to collapse
As expected, it failed even after using the suggested firmware. Does this mean the phone is completely bricked now and nothing can be done?
Did you fix your phone?
Maybe you should consider this?
http://forum.xda-developers.com/showthread.php?t=1840030
austibor said:
Did you fix your phone?
Maybe you should consider this?
http://forum.xda-developers.com/showthread.php?t=1840030
Click to expand...
Click to collapse
Great advice only trouble its a totally different phone you are linking to .
jje
JJEgan said:
Great advice only trouble its a totally different phone you are linking to .
jje
Click to expand...
Click to collapse
Yeap you are right, I should have stated that!
The article states that you should user root66 and Linked boot chains for your device.
This sounds like it might help with OP problem.
He for sure has wrong kernel ... that is similar enough to work but screw is mounting point. Try change kernel with odin ... then flash with odin twrp or philz recovery and flash a proper rom
Sent from my GT-I9300 using xda premium
I have the same problem and still searching the forums for an answer.
does your problem solved? does this flashing and kerneling and odining worked? because I think the internal memory in baked!!
Hi guys, I really hope u can help me, cause i admit i did my share of research and got no solution
My N8010 was using GNABO 6.5 and Boeffla Kernel. While using it the other morning, the tablet suddenly rebooted and got stuck on the Galaxy Note screen. It stays on it a few seconds then reboot to the same screen in a loop.
I can access the recovery menu (CWM 6.0.3.6 ) but my options there are pretty limited, cant wipe and cant install zip files. At the botton of the recovery i have the following logs:
Warning: no file_contexts
E: Can´t open /cache/recovery/log
E: Can´t open /cache/recovery/log
E: Can´t open /cache/recovery/last_log
E: Can´t open /cache/recovery/last_log
I read somewhere that the problem should be solved if i could install a new recovery through Fastboot. Problem is fastboot cant find my device when on bootloader (but i can find it through ADB).
Using ADB sideload to install new recovery or new ROM gave me error on CWM.
Please, save my Tabye.
_Gandour_ said:
Hi guys, I really hope u can help me, cause i admit i did my share of research and got no solution
My N8010 was using GNABO 6.5 and Boeffla Kernel. While using it the other morning, the tablet suddenly rebooted and got stuck on the Galaxy Note screen. It stays on it a few seconds then reboot to the same screen in a loop.
I can access the recovery menu (CWM 6.0.3.6 ) but my options there are pretty limited, cant wipe and cant install zip files. At the botton of the recovery i have the following logs:
Warning: no file_contexts
E: Can´t open /cache/recovery/log
E: Can´t open /cache/recovery/log
E: Can´t open /cache/recovery/last_log
E: Can´t open /cache/recovery/last_log
I read somewhere that the problem should be solved if i could install a new recovery through Fastboot. Problem is fastboot cant find my device when on bootloader (but i can find it through ADB).
Using ADB sideload to install new recovery or new ROM gave me error on CWM.
Please, save my Tabye.
Click to expand...
Click to collapse
Samsung devices don't support fastboot instead they have something called download mode, which you can entered powering off the device and then pressing Volume Down button + Power Button simultaneously, after a couple seconds you'll see a warning screen at the warning screen press Volume Up and the device will be in download mode. Then you can use Odin to flash a new recovery, I would recommend checking out this guide on how to flash a recovery with Odin, and this thread for a recovery you could flash for your device model. Let me know if you still have questions.
shimp208 said:
Samsung devices don't support fastboot instead they have something called download mode, which you can entered powering off the device and then pressing Volume Down button + Power Button simultaneously, after a couple seconds you'll see a warning screen at the warning screen press Volume Up and the device will be in download mode. Then you can use Odin to flash a new recovery, I would recommend checking out this guide on how to flash a recovery with Odin, and this thread for a recovery you could flash for your device model. Let me know if you still have questions.
Click to expand...
Click to collapse
Hey Shimp, thanks for the answer.
Unfortunately I tried to flash both TWRP and Philz Touch and, besides going everything ok with odin, the recovery did not change. It is still CWM 6.0.3.6
any other advice?
_Gandour_ said:
Hey Shimp, thanks for the answer.
Unfortunately I tried to flash both TWRP and Philz Touch and, besides going everything ok with odin, the recovery did not change. It is still CWM 6.0.3.6
any other advice?
Click to expand...
Click to collapse
Did you rename the recovery image to recovery.img before your .tar it and then flashed it via Odin?
shimp208 said:
Did you rename the recovery image to recovery.img before your .tar it and then flashed it via Odin?
Click to expand...
Click to collapse
m
I just downloaded a .tar and flashed it. isnt that right?
_Gandour_ said:
m
I just downloaded a .tar and flashed it. isnt that right?
Click to expand...
Click to collapse
Usually that will work however I have ran into times where I had to make sure the recovery image was named recovery.img and then tar'ed that recovery myself and then flashed it through Odin.
shimp208 said:
Usually that will work however I have ran into times where I had to make sure the recovery image was named recovery.img and then tar'ed that recovery myself and then flashed it through Odin.
Click to expand...
Click to collapse
Did that. No success either. Still same recovery.
_Gandour_ said:
Did that. No success either. Still same recovery.
Click to expand...
Click to collapse
Sounds like it is time to restock with the original firmware and Odin and start over.
es0tericcha0s said:
Sounds like it is time to restock with the original firmware and Odin and start over.
Click to expand...
Click to collapse
Already did that. Nothing happened.
_Gandour_ said:
Already did that. Nothing happened.
Click to expand...
Click to collapse
Another thing you could try is just flashing the stock recovery through Odin, and then flashing the new recovery you want over that in Odin.
shimp208 said:
Another thing you could try is just flashing the stock recovery through Odin, and then flashing the new recovery you want over that in Odin.
Click to expand...
Click to collapse
Well.. i can try that, how can i get the stock recovery? Couldnt find it.
_Gandour_ said:
Well.. i can try that, how can i get the stock recovery? Couldnt find it.
Click to expand...
Click to collapse
Did you use the correct firmware? Did it pass successfully in Odin? Did you perform a factory reset after using Odin to install the original firmware?
Stock recovery can be found here:
http://forum.xda-developers.com/showthread.php?t=2102677
es0tericcha0s said:
Did you use the correct firmware? Did it pass successfully in Odin? Did you perform a factory reset after using Odin to install the original firmware?
Stock recovery can be found here:
http://forum.xda-developers.com/showthread.php?t=2102677
Click to expand...
Click to collapse
Used correct firmware. It did pass successfully through odin. Factory reset seems broken.
I will try the stock recovery.
No success with stock recovery.
So... No way to fix at all?
_Gandour_ said:
So... No way to fix at all?
Click to expand...
Click to collapse
To clarify even after flashing the full stock firmware, then flashing another recovery your still stuck on the recovery you were trying to replace correct?
shimp208 said:
To clarify even after flashing the full stock firmware, then flashing another recovery your still stuck on the recovery you were trying to replace correct?
Click to expand...
Click to collapse
Correct
_Gandour_ said:
Correct
Click to expand...
Click to collapse
What settings are you using in Odin when flashing the stock firmware package?
shimp208 said:
What settings are you using in Odin when flashing the stock firmware package?
Click to expand...
Click to collapse
Put tar md5 file on AP/PDA, leave F Reset Time and Auto Reboot checked.
UPDATE:
I sent the tablet to a local technician and hes gonna charge me U$150 to make a repair on the board and restore the system. Does it make sense to you guys? Should i accept the service?
I'm sorry for posting this here but after about almost a day searching the entire internet for a proper solution, I have given in and have created this thread. So recently I was using my phone and all of a sudden it froze, and after pulling out the battery, it hasn't able to boot. Thinking that it was just another random soft brick, I proceeded to TWRP in order to perform factory reset and wipe data in order to flash a new rom. But unfortunately I keep getting the following errors:
E: Unable to mount '/efs'
E: Unable to mount '/cache'
E: Unable to mount '/system'
E: Unable to mount '/data'
E: Unable to mount '/preload'
...done
E: Unable to mount storage
I have tried to format through adb but haven't been able to find a proper command, most require the phone to be at least booting. Please can someone help me out, I don't want to lose my data but also want to be able to use the phone again!
The problem is most likely twrp. Flash a clockworkmod recovery from the official website in .tar format. Flash via odin as you would a rom. You could also flash a stock recovery the same way.
Sent from my HTC One M9 using Tapatalk
This problem has been happening a lot recently, you might have to repartition
shivadow said:
The problem is most likely twrp. Flash a clockworkmod recovery from the official website in .tar format. Flash via odin as you would a rom. You could also flash a stock recovery the same way.
Sent from my HTC One M9 using Tapatalk
Click to expand...
Click to collapse
Exactly, not only have I tried to install cwm but also tried to upgrade twrp but even through Odin it fails and I get a NAND Write error. Any ideas on how to over come that?
This looks like my problem, but after trying to wipe in recovery, I can no longer boot into recovery at all. Download mode doesn't work either, no Samsung logo is shown, just a completely white screen.
gw666 said:
This looks like my problem, but after trying to wipe in recovery, I can no longer boot into recovery at all. Download mode doesn't work either, no Samsung logo is shown, just a completely white screen.
Click to expand...
Click to collapse
That sounds like your phone got bricked, mine too on the verge of it....
If odin cant see the phone it's pretty much dead as you need odin to flash a stock rom. If you can get it seen by odin just flash a stock rom.
Sent from my HTC One M9 using Tapatalk
shivadow said:
If odin cant see the phone it's pretty much dead as you need odin to flash a stock rom. If you can get it seen by odin just flash a stock rom.
Sent from my HTC One M9 using Tapatalk
Click to expand...
Click to collapse
Odin is detecting the phone but I can't flash stock firmware due to some "NAND Write" error. Any ideas?
@Deathshead747, the standard way: try to flash a 3part firmware + PIT-file to repartition the internal memory. But probably it's gone
rp158 said:
@Deathshead747, the standard way: try to flash a 3part firmware + PIT-file to repartition the internal memory. But probably it's gone
Click to expand...
Click to collapse
As rp158 says. Pit file method. If no go with that its gone to the great big landfill in the sky..
Sent from my HTC One M9 using Tapatalk