I've followed the instructions as best I could.
I have UB with NUT DualRecovery installed (latest), I was on RomAur 3.7
I did a wipe via TWRP prior to installing - installation completed.
Powered off via TWRP.
Flashed the new firmware .314 as instructed using flashtool (kernel and baseband)
Powered off via TWRP.
Booted - Sony logo came up, purple light, purple light off, screen remained black but lit for a few seconds then mobile reboots back to Sony logo.
Any suggestions?
I've restored my backup (thankfully made sure I'd backed up) back on 3.7 again.
I have a D6503.
Related
Ok, here's a story.
Firstly, I switch Fw from 431 to 587 using Flashtool
I've been using Adv Stock Kernel of Sirkay for both of this Rom.
One day, I'm fed up with the Adv Stock Kernel
I decided to switch to xRay 9.587-c
It boot passes the kernel screen into boot animation
But it stuck at my boot animation screen
Stuck
Stuck
Stuck
....(15 minutes)
Stuck
I plugged off the battery, trying to reboot, it boot, pass the kernel screen
and the same thing repeats again
and
again
I reflashed 587 rom again, it boots successfully, switched kernel, boots successfully again, so I decided to push some of my mod into the phone via cwm recovery
Connected to the Pc, I reboot, and it hangs again, this time, stuck at kernel screen, can't go into recovery
so I reflashed the fw 587 via flashtool again, it boots successfully with custom kernel
tried my framework mod, it won't boot, revert back to original framework mod, boot stuck still
so I reflashed fw 587 again, it works, but I'm very careful now
#Suppose that fota in flashtool should be unchecked, right?
#is my trim area damaged????
I need desperate help, guys and devs, I'm so afraid of rebooting now. LOL
Hello
I recently wanted to go back to CM11, but i got stuck on to a problem
I had Honoami V8 installed with the Nemises Kernel on a unlocked bootloader.
I wanted to have clean install so I flashed the Stock 4.1.2 with flashtool that went just fine and i had no problems.
until I flashed the CM 11 kernel with TWRP from Percy_g2.
In the instructions it says that i need to hold the power button to get into TWRP when the phone vibrates on boot, but the phone won't vibrate and it justs cuts to black no matter what I do. I tried it with the Stable M8 version and Nightly-16, but it just does the same.
Any help with this?
The kernel used with the Paranoid rom does work with TWRP. It appears only Cyanogen mod kernel does not work
Mid year I decided to root and flash Cm 11 onto my little s3 mini (gt-i8190) and everything went great. Recently I read on the Novafusion website that they recommend using TWRP instead of CWM, searched on Google and saw it was safe to flash over custom recoveries. I used Odin to flash over the TWRP I downloaded from the Novafusion site. When odin completed its process my phone rebooted into TWRP and it all seemed fine, then I proceeded to flash the latest version of the Cm 11 4.4.4 rom. Again everything went great and my phone booted up normally.
I got the zip file for the Android L keyboard and I used Rom manager to reboot into recovery and showed the "Samsung Galaxy sIII mini gt-i8190 screen and just went black for 10 seconds, rebooted and continued going black then rebooting. I pulled the battery out and booted up my phone again then used rom manager to flash CWM again and it worked! I used CWM to flash the keyboard apk and it worked.
I was a little bit worried about the recovery bootloop and decided to make a nandroid backup. I couldnt reboot into recovery, manual way or with Rom manager.
I have used odin to flash CWM and TWRP a few times now without any luck. My phone just reboots normally when odin finishes.
If anyone could shed some light on this issue I would be grateful.
Thank you.
I tried to install CWM using ODIN, and everything seemed to go well, but when I turned the phone up, it will show the model's name and a yellow warning sign, and then go black forever.
I thought it was because the CWM installation deleted the kernel (It was written somewhere in the guide) so I flashed a new kernel with ODIN, but the problem presists.
I tired to wipe it through recovery, and nothing. any help?
I have a rooted S5 G900T, with PhilzTouch CWM and a stock 5.0.1 rom. I decided to update to 5.1.1 yesterday. I couldn't do the OTA update, so I used Kies. The update worked, except the phone and mobile data wouldn't work. No problem, I thought--I made a nandroid backup before I did anything. I reflashed Philz Touch CWM using Odin, rebooted into recovery, and restored from my nandroid backup. Everything appeared to work successfully.
But now, it's just sitting on the white boot screen. I get the T-Mobile jingle boot sound, and then nothing.
Solutions?
Thanks
problem solved. Reflashed firmware.