Hi everyone, i show you my problem, yesterday i was installing the ics leak rom from T-mobile, at first time installation proceding fine, but multimedia apps didn't works, i tryed to re-flash by doing a second flash of update.zip by the recovery, but now the razr didn't start, he show only the logo M, after a black screen. I can go to the Flashboot, recovery the boot option.
I tried the Wipe cache, Wipe Data/Factory reset but nothing working.
I think that reflash via RSDlite or FlashlT with a ICS rom, the leak will solve this problem ?
Can everyone help me with this big problem ?
Thanks
There's an Thread in General section about saving a bricked Device after the Leak. I'm to lazy to post the Link now
"Unfortunately Setup Wizard has stopped working" - after trying to install Gapps
So I've successfully managed to get the current CM nightly on my S2, after a few trials and tribulations.
I'd left my phone alone for a bit, all working fine.
Then I decide to get it sorted properly, and install the Google Apps.
Googling told me to use the 20120429 version. So I downloaded that (using the phone's browser), went into CWM and installed it. No joy.
Silly me, I didn't reset + clear cache. So I did that. Still no joy.
So now I've re-installed CM and done a reset + clear cache.
And still I'm stuck looking at the 'setup wizard stopped working' messages, in an endless soul-destroying loop
What can I do?
Would re-installing a stock rom and then re-rooting do the trick?
I can't get Odin to connect, and so I've copied the zipped 4.0.3 rom into the internal SD card, but CWM fails (is it because it has a .dll file alongside the .tar?)
I'm wishing I'd left the phone alone now
RostokMcSpoons said:
So I've successfully managed to get the current CM nightly on my S2, after a few trials and tribulations.
I'd left my phone alone for a bit, all working fine.
Then I decide to get it sorted properly, and install the Google Apps.
Googling told me to use the 20120429 version. So I downloaded that (using the phone's browser), went into CWM and installed it. No joy.
Silly me, I didn't reset + clear cache. So I did that. Still no joy.
So now I've re-installed CM and done a reset + clear cache.
And still I'm stuck looking at the 'setup wizard stopped working' messages, in an endless soul-destroying loop
What can I do?
Would re-installing a stock rom and then re-rooting do the trick?
I can't get Odin to connect, and so I've copied the zipped 4.0.3 rom into the internal SD card, but CWM fails (is it because it has a .dll file alongside the .tar?)
I'm wishing I'd left the phone alone now
Click to expand...
Click to collapse
What version of CyanogenMod are we talking about here? You need to be more specific.
themadba said:
What version of CyanogenMod are we talking about here? You need to be more specific.
Click to expand...
Click to collapse
Right, maybe I found the cause of the problem - I've installed cm-10.1-20130125-NIGHTLY-i9100 but when I wanted to find out which version of Gapps I needed I couldn't be sure what it was so I decided to just find the original download page again. But somehow I managed to find this page http://get.cm/?device=galaxys2 (a rather too easy mistake to make?) ...which has version 9! So I've tried to install the wrong Gapps file
RostokMcSpoons said:
Right, maybe I found the cause of the problem - I've installed cm-10.1-20130125-NIGHTLY-i9100 but when I wanted to find out which version of Gapps I needed I couldn't be sure what it was so I decided to just find the original download page again. But somehow I managed to find this page http://get.cm/?device=galaxys2 (a rather too easy mistake to make?) ...which has version 9! So I've tried to install the wrong Gapps file
Click to expand...
Click to collapse
I thought you might have! I'm not sure whether a simple flash of the correct gapps file will solve your problem or whether you will need to wipe data/factory reset, wipe cache and wipe dalvik cache, reinstall the CM10.1 nightly and then flash the correct gapps file which can be found here: http://goo.im/gapps/gapps-jb-20121212-signed.zip
Try just wiping your cache and dalvik cache in recovery and flashing the new gapps file I linked, if the flashing process doesn't last for atleast 20 seconds, then you may have to carry out the steps I listed above for a complete reinstall.
themadba said:
I thought you might have! I'm not sure whether a simple flash of the correct gapps file will solve your problem or whether you will need to wipe data/factory reset, wipe cache and wipe dalvik cache, reinstall the CM10.1 nightly and then flash the correct gapps file which can be found here: http://goo.im/gapps/gapps-jb-20121212-signed.zip
Try just wiping your cache and dalvik cache in recovery and flashing the new gapps file I linked, if the flashing process doesn't last for atleast 20 seconds, then you may have to carry out the steps I listed above for a complete reinstall.
Click to expand...
Click to collapse
Thanks but I've now tried the reset / wipes / reinstalls multiple times to no avail. And now when I connect my phone to my pc to try to put the correct gapps zip on there, Windows Explorer is only showing a few of the folders on Internal Storage. The stuff that I've already got at root isn't showing. Have I knackered my phone?
I'm going to have to leave it til the morning - the battery is nearly empty.
Edit: Damn, I couldn't get to sleep without fixing it first, and luckily I did: I rebooted my pc, and the explorer eventually did show the contents ok (just very slowly). I dragged the zip in, installed it with CWM and *huzzah* it's working! The only odd thing is the camera has disappeared from the applications...
I can wait until tomorrow to work that out.
Thanks for your help
RostokMcSpoons said:
Thanks but I've now tried the reset / wipes / reinstalls multiple times to no avail. And now when I connect my phone to my pc to try to put the correct gapps zip on there, Windows Explorer is only showing a few of the folders on Internal Storage. The stuff that I've already got at root isn't showing. Have I knackered my phone?
I'm going to have to leave it til the morning - the battery is nearly empty.
Click to expand...
Click to collapse
That's strange. I recently flashed a wrong gapps file and it led to some things not working, especially the Play Store. I tried just wiping the cache and dalvik cache and flashing, but that didn't work. So I did a wipe data/factory reset, wipe cache and wipe dalvik cache, reflashed the ROM and then flashed gapps. I think I may have wiped the cache and dalvik cache once more for good luck, and then repaired permissions in the advanced section of recovery. Phone booted up fine and all apps worked perfectly. I doubt the phone is knackered, perhaps try and different ROM just to make sure it boots fine, and then try flash CM10.1 again. Good luck
Samsung Galaxy s2 CM10 trouble Setup Wizard has stopped working
Im from Asia and I guess Samsung s2 int’l version has different features. I already updated my firmware to JB 4.1.2 (leaked) and since I am not satisfied with it,I rooted it and installed siyah as well as cm10 + gapps from XDA links. I followed everything according to the posts and vids.The problem is that after rebooting and CM start up showed up,the next prompt was UNFORTUNATELY,SET UP WIZARD HAS STOPPED WORKING. What’s wrong? I have tried 6x times and no one worked correctly. HELP me!
I was under the same problem few days ago...
flashed 4.2.2 gapps on 4.1.2..
and succumbed to 'unfortunately setup wizard has stopped' error, until i flashed the respective 4.2.2 gapps.
but sadly it ate away my internal memory (cant help )
So the point is
just flash the respective gapps
and then the ROM again
Hi I just installed cyangenmod and it works but setup wizard is crashing and I don't know how to fix this my phone its pretty much unusable. Need help urgently!
The key is to wipe regular cache partition after installing Gapp zip! :]
I think you have the key. I get my cm10.1.5 and I flashed a realy slim gapps (11mb), but after that I didn't wipe cache and dalvik. So the phone didn't woke up because it get stucked in the wizzard setup. So I have to do as u said. And like the other said, reinstall the rom and then the gapps.
Galaxy 5
After using android 2.1 update 1 in my samsung galaxy 5 (GT-I5503)
I updated it with 2.2 froyo then 2.3 then 4.0 then 4.1.
last time I updated to 4.2 CyanogenMod
Before that I could work good in others. But in 4.2 there were problem of contacts in SIM card, these contacts not showing in device.
Then after my device not detacting SIM card for last few months.
Now my phone showing "Unfortunately, Setup Wizard has stopped."
How can I start my phone?
Galaxy Grand CM12 error
Hi,
I have succesfully flashed my galaxy grand and installed CM12 as per instructions given. But i am constantly facing issue of "Unfortunately Setup wizard has stopped". I have tried all the methods mentioned, but still facing same.
Pls Help
fixed this error(setup wizard or google play service has stoped).first you must install cm13 after that install your gapps(use phliz toch recovery) then reboot device.you Will notic that device doesn't boot or you'll have the same problem(setup wizard).come back to recovery and install the other recovery(change phliz touch to CWM) then with wipe install the same ROM and after that install gapps.the gapps won't install so reboot the device.enjoy your ROM with gapps
fix
FOR ANY1 facing this problem on cm13 setup wizard stopped.
just do as i say it's actually funny but it worked for me for the very 1st time.
I tried all the fix given like clear cache or flash new gapps but nothing solved the problem.
So just do what i say.
when u see the setup wizard stopped error.
on that screen just touch all the corner of the screen of ur phone
staring from the top left corner then the top right and so to the bottom right corner and then at last the left most corner.
Just keep trying i doesn't happen for the first time.
Most of u would be thinking it's funny but it actually worked just give it a try.
it helped me might work for u as well
---------- Post added at 07:49 PM ---------- Previous post was at 07:43 PM ----------
dkarry said:
Hi,
I have succesfully flashed my galaxy grand and installed CM12 as per instructions given. But i am constantly facing issue of "Unfortunately Setup wizard has stopped". I have tried all the methods mentioned, but still facing same.
Pls Help
Click to expand...
Click to collapse
bro just start your phone and on the screen where u see the error
leave it as it is and do this:
touch the top most left corner twice like tapping on it nad then the right most corner then the right bottom corner then lastly the left most corner.
it helped me might help u as well
sir,
i have samsung galaxy star GT-S5282 model but i am unabble to start the Device because of error of unfortunately samsung setup wizard has stoppeed
Anyone else have problems flashing to a 4.3 ROM? (I know some people do because I've searched.)
No matter what ROM it is, if it is 4.3 it will always fail to reboot a second time after it has been flashed.
Currently on CleanROM ACE 4.9 (4.1.2) with TWRP 2.6.0.1
I've tried to go to CM10.2 and it would reboot initially but then hang on the Note II logo if I tried to reboot.
I've tried to go to Paranoid Android.. same thing.
I've tried to go to PAC-man.. same thing.
I've tried flashing from the stock 4.1.2 ROM and the same thing happens.
I've followed every instruction I could find including this: http://forum.xda-developers.com/showthread.php?t=2423057
I do a factory reset, format data, flash ROM, wipe caches, flash gapps, wipe caches, reboot. It will boot fine from TWRP and load everything normally. Then, if I reboot or power off the device, it will hang on the Note II screen and I have to nandroid back to my previous ROM.
Any insight as to why this is happening? I haven't been able to find anything besides some random instructions for wiping/flashing (which I've linked). These ROMs look great and I'd really like to move to 4.3, but I cannot figure out what the problem is.
BigBoy275 said:
Anyone else have problems flashing to a 4.3 ROM? (I know some people do because I've searched.)
No matter what ROM it is, if it is 4.3 it will always fail to reboot a second time after it has been flashed.
Currently on CleanROM ACE 4.9 (4.1.2) with TWRP 2.6.0.1
I've tried to go to CM10.2 and it would reboot initially but then hang on the Note II logo if I tried to reboot.
I've tried to go to Paranoid Android.. same thing.
I've tried to go to PAC-man.. same thing.
I've tried flashing from the stock 4.1.2 ROM and the same thing happens.
I've followed every instruction I could find including this: http://forum.xda-developers.com/showthread.php?t=2423057
I do a factory reset, format data, flash ROM, wipe caches, flash gapps, wipe caches, reboot. It will boot fine from TWRP and load everything normally. Then, if I reboot or power off the device, it will hang on the Note II screen and I have to nandroid back to my previous ROM.
Any insight as to why this is happening? I haven't been able to find anything besides some random instructions for wiping/flashing (which I've linked). These ROMs look great and I'd really like to move to 4.3, but I cannot figure out what the problem is.
Click to expand...
Click to collapse
First time installing CyanogenMod 10.2 to your Galaxy Note 2 I605, or coming from another ROM:
- Read known issues ans FAQs
- Flash the latest official ClockworkMod-Recovery
- Copy GApps and CM10.2 ZIPs to your SDCard
- Boot into Recovery
- Flash CM10.2 zip from SDCard
- Flash GApps zip from SDCard
- DO A DATA WIPE / FACTORY RESET (otherwise your device will be stuck at boot)
- Reboot
- Don't restore system data using Titanium Backup!
- Restoring Apps + Data might cause problems and is not recommended, avoid it if possible!
read the OP for CM 10.2 next time....
First - clockworkmod not twrp for 4.3 usually fixes things
Second - do a factory reset AFTER installing
Third - Dont restore apps with TiBu going to 4.3
Next time be truthful when you say you read and searched.
hello,
i never posted here before but i am following this site for a while and flashed lots of roms using the data here.
i got into a problem trying to flash the kitkat on my HTC sensation 4G.
i am using ATM the android 4.2.2 CM 10.1 albinoman887 rom.
i tried installing the android 4.4.1 according the instructions posted by android1234567 here:
http://forum.xda-developers.com/showthread.php?t=2530073
i did factory factory reset, cache wipe, and davlik wipe
after that flashed the Kernel Aroma installer, the rom and the gapps from this link.
after i flashed them i rebooted and the phone doesnt pass the reboot screen, got stuck on it for few seconds and then restart and stuck again.
could anyone help me resolve this?
thanks ahead.
Dan
ok
if mean bootloop then again do the same step but wipe the dalvik cache,data,cache means clean your phone and then install the rom u will out of boot loop
tried it, it didnt work, still bootlooping.
when i install the gapps file it says it detects 4.4 rom.
any other ideas?
thanks for the help
hello xda,
i tried to insatll CM 11 on two SGS3 GT-I9300 and after installation first boot to CM, for any reason if i restarted the phone or power it off the device will power up showing the first Screen of Galaxy S3 model then will go in deep black screen like the phone missed the CM boot file.
Here is the procedure i used to follow, please bare with me and tell me where i did mistake
1- Rooting the device using CF-Auto Root (Optional as i think since there is no KNOX in 4.3 version)
2- Flashing TWRP Recovery using Odin
3- Using TWRP to flash both CM11 stable version and GAPPs
4- Reboot (CM works like charms!!!)
5- Any reboot happen, phone will power up showing the SGS3 Logo then goes in deep black screen!!
please give a hand and help me guys.
milan guy said:
hello xda,
please give a hand and help me guys.
Click to expand...
Click to collapse
Do a clean install. Do factory reset, wipe cache & dalvik cache, wipe System and Data. Flash the ROM and Gapps again.