RK292x + RT3188 based miracast HDMI stick firmware - Android Stick & Console AllWinner based Computers
I just bought this HDMI DLNA / Miracast receiver stick. The model seems to be a "Ugoos UG017" aka "Chromecast MD321" aka "MOCREO iPush M1" aka "HI762 HI763 (Chromecast)" aka "CX-V3" aka "PTV-2R" and possible more names. The hardware is:
- Rockchip RK2928-G @~1GHz
- 256MB DDR3
- 16 MB NAND
- RT3188 WLAN-Chip
- Push-switch to toggle DLNA / Miracast mode
There seems to be a UART available on some test points on the PCB. Any ideas on how to connect to that (settings)?
DLNA through BubbleUPnP is more or less working (skipping seems to lock the stick, playing playlists too), but Miracast is not, at least not on my Xperia L with CyanogenMod 11 / FXP 333.I tried the firmware for the "Pipo X5" and "MOCREO iPush M1" (both ~14MB) and both worked. Both state version "3.0.0-rc2". I would be thrilled if someone could link to a newer (and hopefully more bug-free) version than that...
EDIT: If found a link to a much better firmware (v5.0.0-rc2) for the CX-V3 here. DLNA is much better. Miracast still does not work, but I suppose that's just FXP 333...
if someone is interested this firmware allowed me to miracast with a samsung galaxy tab s
tried other firmwares (CR-M200,ugoos-ug017,CX-V3) but only this was updated
http://www.cloudnetgo.com/CR-M200S.htm
Regards
galaxy tab s
Hi Lucize,
I tried the firmware you posted, but the problem remains: "Impossible to initiate screen mirroring due to a HW problem"
What Android version do you have on your TAB S? Is it a 8.4 or 10.5 version?
Thanks in advance!
CR-M200 firmware on WiFi Display Dongle M806 on SM-G900V
lucize said:
if someone is interested this firmware allowed me to miracast with a samsung galaxy tab s
tried other firmwares (CR-M200,ugoos-ug017,CX-V3) but only this was updated
Regards
Click to expand...
Click to collapse
Thank you so much, lucize! It worked! I was able to miracast with my Galaxy S5 using the built in screen mirroring function. My android version is 4.4.4.
I got a Tronsmart CX-V3 dongle and I was wondering how to update it, since Tronsmart has -of course- no updates. So tried to find some more clones who could have an update and maybe even the manufacturer.
The latest I managed to find is version 9.0.0, dated 21-4-2015, by Ergotech. Their MD3054 and MD3056 seem to be the same according to the doc file in MD3054's update (8.0.0 rc1) (*1), so I downloaded MD3056's (*2) and flashed it. Sunchip-Tech strongly advices to update the software(*3), so i didn't have any hesitations.
A PDF included in 3056's update as well in the *3 link, indicates that there is OTA update option via the manufacturer (Sunchip-Tech). This means that maybe all Miracast sticks of this manufacturer can be updated directly by Sunchip-Tech. Keep in mind that the menu language will be switched to Chinese after the update, but it can be very easily switched back to English in the settings menu.
Ergotech's download page can be found in link *4.
While searching, I noticed than some RK2928 based Miracast dongles were called Lollipop (not because of Android). I searched a bit more and found Rockchip's user guide for RK2928 wireless HDMI dongles(*5), which calls RK2928 dongles as Lollipop. Seems that the reference Rockchip design is followed by the manufacturers. In that user guide I noticed the settings screen is same as my dongle's, but the main screen picture is different though same to some other RK2928/Lollipop dongles I had seen while searching. So probably there is an other manufacturer who kept the original main screen and maybe has even newer software. I did some more searching and the latest I could find is CloudNet's 3.21.00 (dated 28-5-2015) for CR-M200S. This one has OTA settings too, unveiling its manufacturer is Hotack. I believe it is a newer version than Ergotech's/Sunchip-Tech's version 9.0.0 because it has boot version 1.41 instead of 1.40.
CR-M200S download page is at link *6 and in lucize's post too.
Relatively new firmwares are also available by these companies:
Emtec (emtec-international.com/en-eu/Firmware-F100)
Ugoos (ugoos.net/A3S)
*1 drive.google.com/file/d/0B3bETZxL2iACYXdvV2VIdVh4dUU/view
*2 drive.google.com/file/d/0B3bETZxL2iACRXRZWndNRDRwZmM/view
*3 ergotech.com.tw/tw/newsdetail.aspx?id=106
*4 ergotech.com.tw/tw/Download_detail.aspx?key=
*5 upload.sunsky-online.com/res/drivers/S-EAT-0179.pdf
*6 cloudnetgo.com/CR-M200S.htm
talos_2002 said:
I did some more searching and the latest I could find is CloudNet's 3.21.00 (dated 28-5-2015) for CR-M200S. This one has OTA settings too, unveiling its manufacturer is Hotack. I believe it is a newer version than Ergotech's/Sunchip-Tech's version 9.0.0 because it has boot version 1.41 instead of 1.40.
CR-M200S download page is at link *6 and in lucize's post too.
*6 cloudnetgo.com/CR-M200S.htm
Click to expand...
Click to collapse
I can approve that the CR-M200S firmware you linked works quite well. Have you tried the OTA update too?
Latest firmware (MD3056PW 3/sept/15) is from ergotech. Version 10. However there is no dlna subtitle support yet. I am waiting for this firmware to appear soon. None of the firmwares support subtitles over dlna. There is a metadata code that can be used on the firmware to support subs. My nas network disk (twonky server) supports metadata as most do. I am using version 10 without any problems. The only other problem I have is my tablets resolution which is not supported, 1280x 800, which gives me black borders on the sides on the casting TV (when on landscape). I have tried all firmwares with the same result.
There is a metadata code in ezcast forum that they have used to display subtitles over dlna which I am not allowed to post.
Also I have managed to use kodi/xbmc to display videos over dlna but no subs support again. There is a YouTube video and files you need in order to accomplish this.
cypriot said:
Latest firmware (MD3056PW 3/sept/15) is from ergotech. Version 10. However there is no dlna subtitle support yet. I am waiting for this firmware to appear soon. None of the firmwares support subtitles over dlna. There is a metadata code that can be used on the firmware to support subs. My nas network disk (twonky server) supports metadata as most do. I am using version 10 without any problems. The only other problem I have is my tablets resolution which is not supported, 1280x 800, which gives me black borders on the sides on the casting TV (when on landscape). I have tried all firmwares with the same result.
There is a metadata code in ezcast forum that they have used to display subtitles over dlna which I am not allowed to post.
Also I have managed to use kodi/xbmc to display videos over dlna but no subs support again. There is a YouTube video and files you need in order to accomplish this.
Click to expand...
Click to collapse
I tried this vs the CR-M200S firmware, and the CR-M200S firmware is still the best imo. With my iphone that is the only one where mirroring works, and it seems to be less buggy.
Still awaiting a new better update than the CR-M200S . Youtube doesnt work with any of them!
have someone tried mirroring wich this device on wp 8.1?
lokura said:
have someone tried mirroring wich this device on wp 8.1?
Click to expand...
Click to collapse
I also have the same problem. WiDi of windows 8.1 (with supported hardware) does not work with the Chinese miracast dongle RK2928. I get the message:
Your HD digital display device did not supply the required identification data (EDID)
I found this site from sunchip, they say its workin on win 8.1 http://www.sunchip-tech.com/prod_view.aspx?TypeId=12&Id=71&FId=t3:12:3
on the screen captures you can see the firmware versión is 6.0.0 rc3, Im looking for it now in order to test.
working on wp 8.1 witch the soft from ugoos.net/A3S
lokura said:
working on wp 8.1 witch the soft from ugoos.net/A3S
Click to expand...
Click to collapse
Thanks. I will try this too.
I was able to test ergotech v10 firmware. After extensive tests It only worked with WIDI 3.5.41.0 driver. None of the latest intel WIDI drivers worked.
I will try to install ugoos firnmware to see if it works with latest intel WiDi drivers.
Thanks.
Update
Ugos A3S does not work on my Lenovo T420 laptop and Widi Intel 4.3.4.0 (((( I get the same message as before.
Update:
No firmware works with latest WiDi driver.
The only WiDi driver which works with any rk2928 firmware (I tried 3 firmwares) is 3.5.41.0.
Hardware:
Intel i5-2520M VPro
Intel Processor Graphics 3000 HD
Intel Centrino Ultimate-N 6300 WiFi
Drivers
Graphic 9.17.10.4229
Wireless: 15.18.0.1
Software
WiDi application 3.5.41.0 installed 4.3.4.0 recommended (by intel widi update tool but is not working)..
The rk2928 firmware is miracast dlna airplay compatible, without any subtitle support over dlna.
For summary if you want widi support under windows 8 (8.1) then for me only intel widi 3.5.41.0 driver is working.
Also if you want dlna support under windows 8.1 it is possible. Samsung did produce a allshare excellent application which they have now discontinued, and is working like charm under windows 8.1.
Search google and download the Samsung allshare with version: 2.1.0.12031.10 (also called 2.1.0.12031_10)
Last point. For me ergotech V10 is the best firmware on Rk2928 dongle (as I have tested. My dongle used to display a connection name: lollipop)
ios9 airplay
Since ios9 update on iphone Airplay does not work on these dongles any more! and none of the firmware.
The latest firmware located on the ergo-tech website (ergotech.com.tw/tw/Download_detail.aspx?key= firmware v.11.0.0 and 3.0.0 here) claims that it supports ios9, but i have tried ios9.0.2 and 9.1 on these with iphone and it does not work.
Does anyone know a way of getting ios9 airplay to work?
There is a RK2928 dongle which claims to have ios9 support, the Visonicom RealCast VMD-RK156 realcastptv.com/tag/WiFi-display-dongle-Rockchip-RK2928) but i cannot find a firmware download for it.
Kabeern said:
Since ios9 update on iphone Airplay does not work on these dongles any more! and none of the firmware.
The latest firmware located on the ergo-tech website (ergotech.com.tw/tw/Download_detail.aspx?key= firmware v.11.0.0 and 3.0.0 here) claims that it supports ios9, but i have tried ios9.0.2 and 9.1 on these with iphone and it does not work.
Click to expand...
Click to collapse
Firmware 3.0 disables the wifi. So it does not work.
Firmware 11 has problem with the quality. Frames are skipping and video picture gets distorted.
I have tested firmware 11 extensively it is has flaws in video quality. Only ergotech firmware 10 works flawlessly.
I am back on firmware 10.
Tested hardware: miracast rk2928, Lenovo T420 with windows 8.1, intel HD 3000 graphics card, and widi 3.5.41.0 and intel centrino ultimate N-6300 and KODI (xbmc)..
Dear Friends I am in ingrate and desperate situation, I have a briked device m806 black one with antenna, I have Prepare IDB Fail no boot and i try 50 time to flash nothing,I make 2pin shortcut and I have blue square in RK BATCH TOOL 1.7 ,but when i push RESTORE button IDB fail erorr continous! Any advice please,I have a briked device!
alesul said:
Dear Friends I am in ingrate and desperate situation, I have a briked device m806 black one with antenna, I have Prepare IDB Fail no boot and i try 50 time to flash nothing,I make 2pin shortcut and I have blue square in RK BATCH TOOL 1.7 ,but when i push RESTORE button IDB fail erorr continous! Any advice please,I have a briked device!
Click to expand...
Click to collapse
If you are using Windows 8.1 or 10, try flashing your device with windows 7.
I try with 7 and nothing!
any help???
Related
[Q&A] [ROM][Linux/XBMC] Native Linux for Amlogic based Tv-Box's {08/24/2014}
Q&A for [ROM][Linux/XBMC] Native Linux for Amlogic based Tv-Box's {08/24/2014}
Some developers prefer that questions remain separate from their main development thread to help keep things organized. Placing your question within this thread will increase its chances of being answered by a member of the community or by the developer. Thanks for understanding and for helping to keep XDA neat and tidy! :smile:
addons dont work So, i'm sorry if my question was solved in last pages.... Install...done XBMC works smooth But i cannot install any addons, or skins or anything... How i can solve this? Thanks very much!
MX Linux on G18REF with build 6/5/14 I just received my generic "MX" box which is a G18REF and currently has build JDQ39.20140605. Kernel version is 3.0.50. I would like to install MX Linux on this box and am wondering if I needed to a firmware 1.1.5 downgrade first as I saw mentioned elseware. How can I confirm this? Thanks!
remote Hi all, great work, I have a vcom dv141d box I have tried the mxlinux and the openelec and I have the same issue, as soon as the image is applied the remote stops working, I can use a usb remote but the IR won't work, as anyone got any ideas how to get this to work again ? Thanks for the great work ---------- Post added at 09:44 AM ---------- Previous post was at 09:26 AM ---------- Hi, Thanks for the great work, I have tried the mxlinux image, when I convert using the stvmx conversion, my remote stops working I have a vcom dv141d box that's a g02 ref, everything works fine but I have to use a usb keyboard its like the IR as been killed, does anyone know how to solve this Thanks
Jynxbox M1V2 Pure Linux Hello everybody, is it possible to flash this rom to the box mentioned on the title? Thank you very much for your time and answer
G02 kernel source and config Hi, Thanks for these ROMs - working great on my ATV1220 (G02). Please could you point me at the source code and config used for the kernel build? I see some kernel repos at https://github.com/CoreTech-Development but none that seem new enough given that the release changelog suggests that a kernel from March 2014 is being used.
Has anyone tested any of these roms on Bluetimes MX5 G02ref box. Sent from my SGH-I747M using Tapatalk 2
@perro69 i was reading another thread and found that an openelec M8 image has been released : http://forum.xda-developers.com/showpost.php?p=56366456&postcount=211
G02REF I beleive on page 72 of MX-Linuxs thread it stated that gotham-beta2 was a working broadcom version on a droidstick a2 now yes i can get rc1 to work no problem but with no connection it was useless last year. Excited reading about Vitaly_S work i flashed an old A2 stick laying around with BETA 2 (didnt work) and the next comment as an updated build MX_LINUX-G02REFDONGLE_170514..... I apprecite everyone and anyones work over the past year roughly as i was watching this thread from the beginning IE.. croniccorey and vitaly_S just wanted to share that after upgrading screen goes black then after restarting stick its a greenish yellow. so the AM6086A ------ A2 stick is not complient with this release Thanks guys, any ideas otherwise please let me know.
Please help me I got this box http://www.ebay.com/itm/201132479393?_trksid=p2060778.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT I think its a cheap mx 2 android tv box and ive been trying to get xbmc to work on it with no luck, i flashed it with xbmc linux, I followed these steps - http://forum.xda-developers.com/showthread.php?t=2418029 and it worked without wifi but when i turnd the box off for the first time it wouldnt come back on so i sent it back for a replacement one. my new one should be here soon and the only thing i care about is xbmc. the problem i have with xbmc on android software it comes with is it works fine till i turn it off and back on then it only loads like 1min of my movies and its like wifi quits working or something, please help so i dont ruin another box. any help would be appreciated Thanks
reefmonger said: Has anyone tested any of these roms on Bluetimes MX5 G02ref box. Sent from my SGH-I747M using Tapatalk 2 Click to expand... Click to collapse I just reread all 107 pages again to see if I missed something. Has anyone had success with these roms on Bluetimes mx5 g02ref meson6 ? Sent from my SGH-I747M using Tapatalk 2
imx6 box Hi, bought a mx clone from aliexpress want to upgrade the firmware, can I use matricon updates?
toothpick doesn't work How to Restore your Recovery when toothpick doesn't work for mx android box?
MXQ S85 Hi I bought this box from Gearbest. Its the MXQ S85 Amlogic S805 Quad-Core Multimedia Android 4.4.2 TV Box I am looking to load Linux on it for XBMC, any recommendations out there for versions available that will work? Thanks
Mygica atv1200 rebooting over and over I tried to install the mx Linux build for atv1200 posted in the forum here. it said to run the conversion file first then flash the latest release for geniatech/mygica atv1200. I made the sdcard up following the instructions in the readme file included. when I popped the sdcard in and did the upgrade process, it booted to a screen with the Linux penguin, and a yellow progress bar. I seemed to finish then reboot. but it has been doing that same process over and over for the last hour, and it seems not to be working. I tried to revert back to android but it would not boot. I tried making bootable sdcard with geniatech uboot bin, and mygica rom, but it woin't boot. then I made the sdcard with the mx Linux conversion files again, and it boots, but just keeps rebooting with the penguin screen and the progress bar. any help would be greatly appreciated. seems like there are not a lot of people having the same problem cause I cannot find a solution anywhere.
mx2update.zip for v1.1.5 is corrupted mx2update.zip for v1.1.5 is corrupted I can open all the other version mx2update.zip, like 1.1.6, but not for 1.1.5. ---------- Post added at 06:57 PM ---------- Previous post was at 06:50 PM ---------- Hi, How to un-brick this box. G-Box Midnight rev 2.2, 4GB Storage, 1GB RAM, A9 Neon CPU. was running "Linux inside, XBMC 12.2" tried to update to android firmware 1.2.2. now only getting black screen. The blue light comes on, but none of the firmware i put on my 1GB SD card get me any display. I try holding the toothpick for about 2 mins, but no sign that it is working. Can't get into recovery, even if i am there no way to be sure. Can someone help me? Thanks.
Amlogic M3 I managed to flash an early xios linux "the hydra" xbmc onto my amlogic droid stick but the wifi is completely gone which makes it hard to do anything. For some reason my unit doesn't have a bootloader, nor a reset button (so i'm doing the advancedlauncher -> sh -> reboot recovery way in xbmc) and there doesn't seem to be any other recovery roms available for it. Figured i'd try the M3 linux from here, but apparently this is configured to assert a getprop for specific hardware. I can change that myself, but when i sign the zip my unit refuses to go past that verification. With this rom the signing verification is fine, but assertion fails. I can fix that myself but how did you go about and sign the zip? I've tried a few different ways (apksigner, jarsigner) to no avail. There is very little information on what recovery (3e) actually checks, any clues on how to resolve that? (All it says is signature verification failed when i sign, with test keys and self made other keys). Best Crypth
Which firmware for generic G18REF Hi I purchased a generic MX2 G18REF, Which firmware should I install Matricon 1.1.5 or 1.1.6 before installing Linux MX? Thanks
Cheap DX M3 stick won't work. I just flashed the M3 (f16ref) based one on my cheap Amlogic AML8726-M3 stick (1gb ram, 4gb nand, 1.5Ghz), this didn't quite work out and it seems i can't flash other stuff on it either now. Just want to warn anyone else trying this
Codesnake help needed I have a square s802 M8. I recently tried several different OpenELEC zips, most zips received NO FOOTER errors and would not install but most of the ones that did install, did not have any access to wireless networks under OpenELEC settings. Including Codesnakes ROMs. They would not allow access to wireless networks. So, I finally came across a Russian zip on xbmc.ru that installed and it is the latest developer zip found at: OpenELEC-Amlogic.S82.arm-devel-20150113183017-r20272-g0481f0c.zip. After zipping it to the s802, I realized it is for the S82. It still worked but it seems to have some bugginess. It is getting stuck on the opening stream window and the working spinning wheel is getting stuck too often. I am used to Stane's MX Linux and got spoiled with speed. Please help, I need a network working .zip with audio/video synced properly and speed. Any suggestions on a more suitable ROM zip? All of codesnake's OpenELEC ROMs seem to not have wireless networks enabled. Is there a way to have ethernet hooked up after installing codesnake's zip and then get wireless by downloading a network setting addon or enabling an OpenELEC setting feature??
Miracast app for Leelbox Q3 S912?
Does anyone have a Miracast apk that works with a S912 box, or can you pull the apk from your amlogic box. I got the Leelbox Q3 (S912/2GB ram dual wifi) but the Miracast app isn't included and not available for download on their website. I want to use the box as a Miracast receiver, not a sender. Thanks
Update: have contacted leelbox support this morning, waiting for a reply. In the meantime I did find a miracast.apk in an update for a for a himedia A5 box and sideloaded it and its working. Version 2.0.20160324, no idea if this is current but I was able to play video from my Win10 laptop via miaracst. So far I'm impressed with the Leelbox Q3 S912 2/16 box. Its basically a barebones system, minimal lag, good wifi speeds, will keep tinkering. If you guys have any suggestions or ideas please let me know. My goal is to turn this device into a Miracast/Widi wireless display adapter for Windows 10 laptops and Android phones in a conference room. We have a Microsoft adapter now but its too laggy with video and none of the EZcast dongles and other display adapters are working any better. Edit: people keep sending me pm about this. To get the miracast apk I downloaded himedia A5 update from here on a PC then browsed to system -> app -> Miracast folder and pulled the apk and put it on the box with a flash drive
hi thr, even i was looking for Miracast Version 2.0.20160324 apk file, but not getting it online..can u pls share download link..pls let me know..thnks.
te deje esa version en el blackmart meconfusedthinker said: hi thr, even i was looking for Miracast Version 2.0.20160324 apk file, but not getting it online..can u pls share download link..pls let me know..thnks. Click to expand... Click to collapse te deje esa version en el blackmart
look man just install airpin pro apk reciever on box and the cast apk on the phones and the pc version / desktop version on windows then connect to common wifi network and they will be able to share screens or cast video etc etc
someguyatx said: Does anyone have a Miracast apk that works with a S912 box, or can you pull the apk from your amlogic box. I got the Leelbox Q3 (S912/2GB ram dual wifi) but the Miracast app isn't included and not available for download on their website. I want to use the box as a Miracast receiver, not a sender. Thanks Click to expand... Click to collapse hi, do you have any Custom Amlogic rom that will work with this divice ?
S905x (Android 7.1.2 ) TV Box GamePad support
Hey all, I just got a MXQ Pro+ 4K (Android 7.1.2) hx_s905x TV box with 3GB RAM / 32GB ROM. Tested SU root with a root testing app, says the device is rooted ok. I checked for software updates and it says that Android is up to date: Android Version: 7.1.2 Security patch level: May 5 2017. Kernel version: 3.14.29 (March 2018) Build: hx_s905x-userdebug 7.1.2 NHG47L 20180316 test keys Rev B5 I can not get my Logitech Rumblepad 2 wireless gamepad to work with it. Trying to avoid flashing a new ROM or anything that could brick it so I'm only looking for drivers for it and instructions on how to install them. Good news: 1. I see the device listed as plugged in through the "USB Device Info" app, it recognizes it as Logitech Rumblepad 2 and recognizes another generic gamepad as well. 2. Gamepad is not broken - my old Android Box with Android v.4.4.4 detects it just fine, I can play games and navigate through Android UI on it using the gamepad. Bad news: 1. Neither the Logitech Rumblepad nor the generic gamepad work in games or in Android UI on the MXQ Pro+ 2. Tried a bunch of gamepad testing apps from Play Store but no values come up, it is not detected at all. What I need help with: Drivers, modules... anything that will allow gamepad support on Android 7.1.2 and instructions how to install them. Can anyone point me in the right direction? It is really weird that an older Android comes with support out of the box yet the latest one doesn't.
I know this is old, but after doing searching, it seems like no one replies to these threads with gamepad issues. Is this just something that's troublesome for devs to implement? Are the driver modules just not available? I am in the exact same boat as you, I'm hoping in the future I can turn my little android boxes into steam link + htpc devices.
What is the best custom rom for BQeel 2019 Y4 MAX Amlogic S905X2 4GB / 64 GB
I own the Bqeel 2019 Android 8.1 TV Box Y4 MAX / Amlogic S905X2 Quad Core / 4G DDR4+64G eMMC / Dual WIFI 2.4/5.8G + 100M LAN / tv box Bluetooth 4.0 / USB 3.0/ HDMI 2.1 /4K Smart TV Box . I have tried many custom roms and none of them seem to work in the correct manner. I am able to use the latest USB burning tool but lot of these custom roms will flop on me after the install process. I feel like there is something usually wrong with the WIFI side. if it is not a wifi problem, then it is the remote control. I have yet to find a custom rom where I can load and then use the device the way it is suppose to be. I want the remote to work correctly. Keep in mind that I do have a direct Ethernet connection for this device. I have contacted the original manufacturer hoping that they can send me the original default firmware. Back to the topic, i am interested in the best, the latest, and the one the works the most for this device. All solutions have failed for me thus far. ps: i will re try the following .img files that I was able to obtain from FreakTabs - XTM_ATV_X96_4_4 (this one will not connect to the internet directly. it needs a cell phone or tablet, so i can transfer over the Wifi and Google Account settings. For some reason, this is impossible because it keeps asking for my WIFI password which i have entered many times in the device); - Poison_S905x2_V2.0 (this one is easy to install but after the install, the GUI seems stuck. I can't open up any apps, and the weather icon is always spinning). Again, i have tried maybe 5 different custom roms from freaktabs (i am sure they are posted here) and none of them seem to work.
Hello , i have same issue here i flashed many times with many roms and no one work properly. Sometimes i have no wifi/ethernet or no remote. please if someone have the stock firmware of Bqeel y4 max 905x2 4/64go Post it!! really sorry for my english
alilous1000rr said: Hello , i have same issue here i flashed many times with many roms and no one work properly. Sometimes i have no wifi/ethernet or no remote. please if someone have the stock firmware of Bqeel y4 max 905x2 4/64go Post it!! really sorry for my english Click to expand... Click to collapse I have the same problem. I have tried many custom roms but nothing seems to work. Wifi and Bluetooth issues is a problem. I too need STOCK firmware. I have extra device that is not been messed around with but i do not know how to make back up from stock rom. If i can make stock up rom with one app, i will do it ASAP and perhaps share it. Edit: So I am able to obtain a back up of the stock firmware via Twrp from my second device, but it is not compatible with the other Bqeel system. All i see is the Bqeel Boot Logo. I am still able to boot into recovery, and i can also install other custom roms (those custom roms stink). I still need the orgiinal stock firmware in .img or i need a custom rom that actually works really great. For those who want to purchase this device, you can but do not mess with custom roms. Just remove default apps and enjoy the default OS.
I contact the seller of my box (bqeel y4 max 4/64go) today he gonna send me the stock firmware Asap. I 'll share it when i 'll recieve it. Thanks
alilous1000rr said: I contact the seller of my box (bqeel y4 max 4/64go) today he gonna send me the stock firmware Asap. I 'll share it when i 'll recieve it. Thanks Click to expand... Click to collapse I did the same thing. They sent me the stock firmware. the device works great now! there is another hiccup though. For usb burning tool, you will need some license files. when you load the .img file in the program, it will not accept it. You need the license files (just transfer them in the directory in usb burning tool) here is the link for license files and stock firmware. https://mega.nz/#F!TvoShAAK!Jd0X15aoHWVdOf1rrYPc0g
I tried that firmware in my box and it freezes on logo!!!
any news for this device? I have tried many custom OS but none work due to missing drivers.
LooseEnd85 said: I did the same thing. They sent me the stock firmware. the device works great now! there is another Click to expand... Click to collapse What did you actually wrote into the message? I'm in touch with them since a few days but I cannot go over than "we can replace the unit"! BTW, my Device Build Fingerprints: Amlogic/u211/u211:8.1.0/OPM1.171019.011/20190402:user/release-keys Bqeel 2019 Android 9.0 TV Box Y4 MAX / Amlogic S905X2 Quad Core / 4G DDR4+64G eMMC / Dual WIFI 2.4/5.8G + 100M LAN / tv box Bluetooth 4.0 / USB 3.0/ HDMI 2.1 /4K UHD Smart TV Box Yes... it should have android v9 but it's a v8.1... I found the error when the Amazon return window was already closed...
https://www.bqeel.net/download.html There are firmwares from bqueel
Hi Can somebody now tell me if firmware from bqeel.net works or not becuse I've seen a loot that say it's stuck at logo screen or it won't boot Does it work or no?
so far the best custom ATV ported ROM I've found for this box is here: https://forum.freaktab.com/forum/tv...ionatv__bqeel_u214-y8_max_1000m_s905x3-test57 it is due for an update but works as is. I also have a SlimBox ROM that works for the Bqeel but I'll have to upload that to my Mega folder and share the link. EDIT: nevermind my boxi s the Y8 Max this is asking for the Y4 Max,.
TX9 Pro S912 Amlogic
Hi, I've recently flashed Aidan's rom ATV9 on the subject box. Everything works perfect except that Audio passthrough is not supported through Kodi. So my receiver does not play Dolby digital/plus, DTS etc... I understand it's not the ROM's problem. I read extensively on this topic, and found from Kodi's forum that this is a problem specific to Android 9. If the OS does not support audio passthrough, then Kodi won't be able to pass through the raw audio. I had android 7 installed on the box which supported audio passthrough, but this version is so old other functionalities are not available. I'm wondering if Android 8 would solve this problem. If yes, does anyone know if any past versions of Aidan's rom are available (possibly have an android 8) for testing. I can only find version 9 on the internet now. thanks! J