I wiped stock on my rooted droid razr. Now I'm unable to get back to normal. When plugged in to wall I get m logo. I can get into recovery n try to flash firmware but no luck. Reads file_getprop:failed to stat " system/build.prop:no such file or directory
Rsd didn't work either .got XML file n was connected fast boot but phone was not recognized. N/a
I'm stuck need help
This never happened to me... but i hope that somebody can help you in this thread:
http://forum.xda-developers.com/showthread.php?t=2194825
freddyfingaz said:
I wiped stock on my rooted droid razr. Now I'm unable to get back to normal. When plugged in to wall I get m logo. I can get into recovery n try to flash firmware but no luck. Reads file_getprop:failed to stat " system/build.prop:no such file or directory
Rsd didn't work either .got XML file n was connected fast boot but phone was not recognized. N/a
I'm stuck need help
Click to expand...
Click to collapse
try to boot to stock recovery and do a complete wipe...next boot into ap fastboot and your phone should now be detected by rsd lite...
and then you can flash a firmware depending upon your preference...
hope this helps
freddyfingaz said:
I wiped stock on my rooted droid razr. Now I'm unable to get back to normal. When plugged in to wall I get m logo. I can get into recovery n try to flash firmware but no luck. Reads file_getprop:failed to stat " system/build.prop:no such file or directory
Rsd didn't work either .got XML file n was connected fast boot but phone was not recognized. N/a
I'm stuck need help
Click to expand...
Click to collapse
Just flash it using rsdlite
download the file to flash depending your region
install the motorola device manager on your system
charge your phone for a few hours
then press the power and volume down buttons for five seconds (when your phone is off) then let go it should say ap fasboot mode and at the bottom battery ok
connect it to your system and then flash it
Related
Recently tried flashing to CM7. It appears the install completed fine (flashed using CWM) but can't get past boot screen. Showing Motorolo boot screen/unlocked.
I've also tried flashing to [Gobstopper] Bell GB 2.3.4, install completed but still same result, frozen at boot screen.
Can Access CWM recovery but cannot access RSD or FastBoot, battery is too low to start these functions.
Phone won't boot up using battery, can only turn on phone using A/C adapter.
Any insight how I can charge up my battery? It appears it won't charge under CWM. When plugging into PC via USB I get a green solid light.
Any help would be greatly appreciated!! Thanks in advance.
Go to RomRacers CWM Recover thread HERE and download the latest ROMRacer recovery and flash it.. He has both img files and CWM flashable zip files. After flashing re-flash CM7... It seems that you are not using a recovery that has EXT4 capabilities, which is why you are stuck on the Boot logo.. Hope this helps.
Thanks for the quick reply!
The problem I'm facing is that my battery is dead. It doesn't appear to be charging while in recovery mode. I can't keep my usb storage mounted long enough to copy the zip file over. The phone works fine while plugged into A/C.
Any way to charge the battery while in recovery mode?
No way of charging while in recovery mode... So you said you cannot boot into fastboot or ADB? How are you getting into CWM? If you can get into CWM, you should be able to get into fastboot to flash the .img file.
fastboot erase recovery
fasbtoot flash recovery recovery-green-atrix3.3.img
Click to expand...
Click to collapse
or
moto-fastboot erase recovery
moto-fasbtoot flash recovery recovery-green-atrix3.3.img
Click to expand...
Click to collapse
Depending on the fastboot you have... and which img you pull
You could always try letting your phone sit there powered off plugged into the AC charger to see if it will charge.
I can boot into CWM while phone is plugged into A/C power.
When I try opening fastboot or ADB I get a message stating the battery is too low to flash. No fastboot/RSD connections can be made to the phone.
Yep.... need battery. You could try to go to a local AT&T and see if they will let you use a battery out of a display or put your phone in their display model for an hour
Problem fixed once updating to RomRacers CWM Recovery. Thanks again for your help!
No problem! Glad it worked out for you!!
romracers newest after flash should read 5.0.2.3atrix4.1 and it works great!
us-alienv4UL /OC1.3V2.0{webtop2sd(fixed}CWM5.0.2.3atrix4.1
I have a photon with ALIEN ROM+rooted Using AIO method with CWM installed.
I tried to update my photon running using RSD lite with "1FF-sunfire-user-2.3.4-4.5.1A-1_SUN-198_7-CM-release-keys-signed-Sprint-US.sbf".
.After completing 75% it failed with the message "failed flashing process.Phone".
After wards I tried "1FF-sunfire-user-2.3.4-4.5.1A-1_SUN-154_5-CM-release-keys-signed-Sprint-US.sbf". Still the flashing process fails at nearly 75 %.
I am using RSDLite 5.5 version on windows XP.
What should be done next???How can I check the SBF I downloaded is not corrupt?
Is there any method I can recover my device from this soft brick state???
thanks in advance
I was able to flash 154 successfully
I had a problem last night it would stop at creating image... I later reallized its because I had no space left on my C:. Image file is pretty big when uncompressed.
were you able to flash stock 154???
The failed to boot RSD 2 is generally cause you messed up some place along the line, I've done it a couple times. And I was able to flash the 198 update afterwords and the 154 as well with no issues.
Try going to Yay's thread and download the 198_7 build and flash that. It worked on my phone, so the files shouldn't be corrupt.
I had this happen a couple times..
1) Make sure your phone is charged all the way up
2) Plug your phone into the back of the computer
3) If you used titanium backup to delete something and can't get it back, I'd factory reset/wipe and let the phone update itself,
4) or when you get to stock, flash the latest SBF through RSD again and it SHOULD work
Thank you All. The problem was USB port of my laptop.Changed to another port and it went smoothly
Good deal. Glad that helpes out.
Sent from my Photon via XDA
well i was wondering if you guys can help me out... my phone reboot all of a sudden and now says "fail to boot 4 starting rsd mode battery to low to flash"... but i have it connect on power socket ... when i connect to usb only white led shows up... if any body can help me thanks!!!
Try plugging it in to the wall socket and leaving it to charge. I had my phone in moto logo loop and it powers on when you plug it in, but after a few hours it was able to flash, even though there is no sign it is charging
Sent from my MB855 using XDA App
ok i will try dat... but when i leave plug in it starts up and it says faill to boot.... starting... battery to low to lfash... ill try dat thanks broe!!
I got working just had to charge my battery on a separate photon so battery could be full and it could flash
Sent from my MB855
Well I got myself into it this time. I have a Rogers Canada XT910 razr. I installed the Arctic rom and lost all my data connection, and all my apps and could not reload them from google play because it says they are already installed. So I did a wipe and reset and decided to try to use RSD to reflash the ics leak. The flash failed, and my phone is bricked. What's guy to do.
Thanks
John
http://forum.xda-developers.com/showthread.php?p=27944788
That's the leak you need I guess.
There's just one Problem. You need an patched Boot. Img and the system signed of the necessary GB Rom.
I've not searched this Thread for an boot. Img. Maybe someone posted one.
I'm not sure, if you can flash the European Fastboot Files, to get an working RazR, till there's an solution for you.
Gesendet von meinem XT910 mit Tapatalk 2
Thanks man. I had already side loaded the leak that you had linked to so I was on ics before I tried the arctic. I will try tonight to install the European version. I'll let you know how it goes.
Well I am at my wits end.
I eventually got my phone to reboot back into the Arctic rom I loaded, but can't figure out how to update this rom or load another. I have tried with RSD to flash a different flashboot files, but they all fail. I have down loaded a few different custom roms and loaded them on my sd card and tried updating my phone from external storage through the Android system recovery utility but action is always aborted. I can't load any apps like rom manager, file manager, or anything for that matter. When I go to the play store and look at my apps it says i already have them all installed and can't load any. What can I do?
Well I can't seem to leave well enough well enough. tried a few more things and now the phone won't boot. It gets to the Motorola logo and turns off. So can I can get to fastboot and recovery or off. Brutally expensive paper weight.
Can help
hammily said:
Well I can't seem to leave well enough well enough. tried a few more things and now the phone won't boot. It gets to the Motorola logo and turns off. So can I can get to fastboot and recovery or off. Brutally expensive paper weight.
Click to expand...
Click to collapse
I bricked my Rogers RAZR too and was able to fix it. It's a matter of finding the correct signed img and flashing it using the fastboot (when starting phone press power and hold volume up if I remember correctly). Will check what the name of the image is and get back to you. I flashed three or so different images before it would finally boot, then I was able to re-root it, install CWM and get back on my feet.:good:
The rom I loaded is European from here.
http://forum.xda-developers.com/showthread.php?t=1760702
I have been bricked before and fixed the issue, but after loading this custom rom the flash I used the first time with RSD does not work. I appreciate any help and I am willing to try what ever. I did not impress my wife with this one.
flash this
http://forum.xda-developers.com/archive/index.php/t-1634223.html
then reboot....it will work
Thanks I will try it after I get home from work today.
[TUTORIAL]
1. Download the empty_radio.img
2. Turn off the Razr
3. Power On the Razr and select Fastboot Mode AP
4. Open the command prompt CMD
5. Go to the folder where the radio is empty
6. Make flash the radio with the following command and then type "fastboot reboot"
7. Rest assured I tested on my Razr this command does not erase the radio
8. This command will only restart the fastboot
9. Now then turn off the Razr holding vol - and power
10. Plug the Razr holding vol + vol - and power and have it start normally
11. Now restart the fastboot screen will not show more ...
This stuff is over my head. I don't know how to do steps 4,5,6. I don't know what to do in command prompt, I can't find the folder where the radio is empty, and I don't know how to flash the radio. I am totally lost.
Does any body have any other Ideas?
Have you tried fastboot with rsd lite?
Sent from my DROID RAZR using xda premium
Yes I have tried flashing several different XML files from different ROM's With RSD lite 5.7. The flash always fails. In RSD it says that my phone is connected, but it does not show my IMEI it just has N/A in that box. When I hook up my wife's phone which is totally stock it does show her IMEI. Could this be part of the problem?
Hello everyone, this is my second post in the community and as above, I draw you before the serious problem that has my cell phone and that despite the help of all of you still not solved enclose descriptions videos and fails the steps and followed over time. :crying::crying:
All this happened when installing from retail jb rom ics one Chinese, after the installation the cell began to discharge too fast to the point of completely unloaded and not turn over, the next thing was wired switch it could enter the factory and then recovery only restarted.
after the above procedure to unbrick with Unbrick method & switch to 982.124.14.XT910.Retail.en.EU with which obtube not any response, after that a user community graciously offered to assist and I sending the same procedure but with the files for my region (Latam) after that the phone showed the motorola logo and restarted but at times passed motorola logo and showed the animated logo motorola, encendia the lights cell buttons and screen bottom came out "Wait a minute" restarted (enclose one. rar with videos of procedures performed and detailed information.
I count on your help and already thank you very much for reading my topic and I hope to get my phone I need too :crying:
:victorydt: my apologies for the bad drafting but all this is performed with English translator (I'm from chile) :laugh::laugh:
Hi,
Based on your video, I haven't see you flashed with RSD Lite and fastboot file.
You can give a try based on this thread:
http://forum.xda-developers.com/showthread.php?t=2231289
Download LATAM fastboot file (Chile should be latam right?) and download also latest rsd lite ver 6.1.4
Good luck and hope it will unbrick your phone.
idwijayaku said:
Hi,
Based on your video, I haven't see you flashed with RSD Lite and fastboot file.
You can give a try based on this thread:
http://forum.xda-developers.com/showthread.php?t=2231289
Download LATAM fastboot file (Chile should be latam right?) and download also latest rsd lite ver 6.1.4
Good luck and hope it will unbrick your phone.
Click to expand...
Click to collapse
reaches the motorola dual core logo and restarts :crying::crying:there some method other than by fasboot?, or some solution?
Have you download fastboot files that match with you region? if yes then you have same issue with me
So far what I know to flash is use batch file that developed by awesome developers here and RSD lite.
Have you try this:
- Go to boot menu (the way you get AP Fastboot menu) but this time try to select BP Tools
- and wait will your phone able to boot into system or not... If you able to boot into bp tools, get your phone root (JB is able for root now, get the thread in development), then install BMM to have it normal boot .. I got this suggestion but never able to have my phone boot in BP Tools, so I never know this works or not so good luck
- When you choose BP Tools and your phone still on M logo turn it off (you should wait only 10 or 15 minutes max) then turn off your phone and put it in boot menu to select BP HW Diag.. then.. we have same issue.. be prepare your phone only able to phone call , sms , taking camera, cannot access data only rely wifi , USB debugging not working, some fastboot files makes your phone not able to charge (I have to turn off my phone then charge)
I still strugling to have my phone back to normal also..
idwijayaku said:
Have you download fastboot files that match with you region? if yes then you have same issue with me
So far what I know to flash is use batch file that developed by awesome developers here and RSD lite.
Have you try this:
- Go to boot menu (the way you get AP Fastboot menu) but this time try to select BP Tools
- and wait will your phone able to boot into system or not... If you able to boot into bp tools, get your phone root (JB is able for root now, get the thread in development), then install BMM to have it normal boot .. I got this suggestion but never able to have my phone boot in BP Tools, so I never know this works or not so good luck
- When you choose BP Tools and your phone still on M logo turn it off (you should wait only 10 or 15 minutes max) then turn off your phone and put it in boot menu to select BP HW Diag.. then.. we have same issue.. be prepare your phone only able to phone call , sms , taking camera, cannot access data only rely wifi , USB debugging not working, some fastboot files makes your phone not able to charge (I have to turn off my phone then charge)
I still strugling to have my phone back to normal also..
Click to expand...
Click to collapse
did not work :crying::crying: still coming to dual core logo and restarts, other help......
Esto.Vir said:
did not work :crying::crying: still coming to dual core logo and restarts, other help......
Click to expand...
Click to collapse
Reflash the appropriate fastboot once again and then reboot into stock recovery and do fill wipe data and chaches . It may fix ya problem
Thx
Hit the thx button if i helped ya in anyways
anurag.dj2u said:
Reflash the appropriate fastboot once again and then reboot into stock recovery and do fill wipe data and chaches . It may fix ya problem
Thx
Hit the thx button if i helped ya in anyways
Click to expand...
Click to collapse
and tested with the brazil retail rom, fido, rogers ye had the same problem, my question is, if all the rom's the same that another problem will have my phone? , I can enter the ap fastboot recovery and all that d the stock recovery, my phone stayed brick to install a Chinese jb rom this tutorial :
http://www.chileandroid.com/t16992-romxt910jelly-bean-jelly-bean-41-2-china-retail-oficial
, Change kernel and everything that goes in the guide, that will be a problem? I hope you can help me from now thank you very much:crying::crying:
Hello, yesterday while trying to encrypt a folder in the internal memory in the beta program, I discovered to my horror that the entire internal memory(sdcard) have been erased. I do not know how or why. After reset, the overhang on the logo. I have uploaded JB o2, retail Europe, does not start up the phone. Overhang on the logo or bootloop. I try this http://forum.xda-developers.com/showthread.php?t=2505254. In the end I took the tutorial in this topic http://forum.xda-developers.com/showthread.php?t=2194825&highlight=unbrick&page=4, phone starts up but after a reboot bootloop. After re-uploading the Blur files phone starts, but after a reboot bootloop again. Does anyone have any ideas?
Regards
kamel828 said:
Hello, yesterday while trying to encrypt a folder in the internal memory in the beta program, I discovered to my horror that the entire internal memory(sdcard) have been erased. I do not know how or why. After reset, the overhang on the logo. I have uploaded JB o2, retail Europe, does ot start up the phone. Overhang on the logo or bootloop. I try this http://forum.xda-developers.com/showthread.php?t=2505254. In the end I took the tutorial in this topic http://forum.xda-developers.com/showthread.php?t=2194825&highlight=unbrick&page=4, phone starts up but after a reboot bootloop. After re-uploading the Blur files phone starts, but after a reboot bootloop again. Does anyone have any ideas?
Regards
Click to expand...
Click to collapse
First of all stay calm and relax all can be solved....
The best way for flash again the rom is use rds lite
For flash a 4.1.2 you have to use rds lite 6.0 (google it)
Also you need to install the usb drive otherways your razr will not connect perfectly
If you have the 4.1.2 europe try another one like the german retail or the franch one
SO:
Turn off (power botton and vol -)
Let it charge a little bit (half battery will be ok)
enter recovery mode (power vlo- vol+)
go in ap fastboot using vol - and power for confirm
decompress the file you want to flash (in a folder and rename as you like)
launch the rds (remember install mototrala driver)
search the folder where you extract the rom and double click on .xlm file
plug the phone in pc,wait few seconds (10)
click on start
wait
done
some link
rds 6.0 http://forum.xda-developers.com/show...php?p=32900727
Motorola drivers https://motorola-global-portal.custhelp.com/app/answers/detail/a_id/88481/action/auth
rom to flash http://forum.xda-developers.com/showthread.php?t=2231289 Retail british work for me
Finger crossed for you
Phone starts after flashing, but after switching off no longer runs. It hangs on a moving logo Motorola. Every few attempts to phone starts up again after a reboot unfortunately hang.Wipe data and cache does not help. I used RSD Lite 6.0, I downloaded the drivers from the Motorola version 2.43, the system is a Retail France from the given topic. Regards and thanks for help.
EDIT:
Phone boot up in BP HW Test mode in stock recovery. After reboot in normal mode phone still bootloop.
Regards
Anyone have any idea? I ran out of ideas. I had installed BBM and Retail JB slot 1 if it has any meaning.