Helloo
I register in this forum because my mobile is dead. One month ago suddenly it started to reboot and now I can´t swicht on it, I am trying to use the flashtools and use a ROM for revive my mobile.
My computer and the flastools recognize the mobile drivers, but all the time appears the same error:
BROM ERROR: S_FT_DA_ENABLE_DRAM_FAIL (4032)
I tryed with different computers, different ROMs, different SO and I couldn´t do nothing.
I write this post for ask any idea or possible solutions that somebody can give to me, I don´t know which more can I do....:crying:
uupp
uppp
uupp
:crying::crying:
up
Related
Hi all,
please help me out because I'm desperate.
Yesterday I received a THL W8 mobile phone and I flashed it with the ROM reported on this thread.
Once done, my SD card wasn't recognized by the phone, so I decided to flash the same ROM again.
Unluckily, my bad, I didn't uncheck the PreLoader tick and as result now the phone doesn't boot at all.
The PC recognizes it and the drivers are ok, but when I try to flash a ROM, any ROM, I get different errors.
With SP Flash Tools version "SP_Flash_Tool_v3.1304.0.119" the bottom bar fills red fully (100%) but after about 40 seconds it gives me the following error:
S_FT_ENABLE_DRAM_FAIL (4032)
With the SP Flash tools version "AntiBrick_Flash_Tool_v3.1224.0.sn85" 3 seconds after the bottom bar gets filled in red, the following error is returned:
SP FLASH TOOL ERROR: (8200)
[Platform Error] The load and target are inconsistent!
I've also tried to flash the stock ROM but with the same bad results. More, I tried to do a reset with both the aforementioned Flash tools versions with success, but after that whenever I try to flash the phone with any ROM, I get the same errors as before.
Since the PC recognizes the phone I'm kinda sure it can be restored, but apart what I tried already, I'm out of ideas.
Any help is welcome
Thank you guys
Cheers
Heide
really? no one really answered the poor guy, the phone ended up bricked for good after all
good I need help, I bought a lenovo s900 and now is supposed to be a Fake S90 +. When trying to change the ROM with another different with smtools, now no lights or display. So if when you connect and disconnect the USB if the PC recognizes it. And I tried several times but nothing putting on a ROM, I always skip the error
BROM_ERROR : S_DL_GET_DRAM_SETTING_FAIL (5054)
I think everything is erased completely even preolader please .. If you can help me or pass me the original rom stock it. The processor is leading MT6572.
Greetings hope your help
Xavier
What happened:-
I have Micromax A114(Canvas 2.2) which has MT6582 chip. One day when I restart my phone got a screen with white background that says "Encryption Unsuccessful" you need to reset ur phone. I tried to wipe cache and data from recovery it said "unable to mount". So I re-flashed the official stock rom(the one that I was running on my phone) but the flash process was unsuccessful.
You will find all the screenshots here http :// download. pratiyogitadarpanpdf. com/cover/a114flash /index.php
What is the current situation with my phone:-
It is not starting up not even any sign of charging when connected to charger, but when connected to my laptop it shows "Micromax A110 Preloader USB VCOM Port (COM42)" in the device manager. Sometimes it also shows "MediaTek DA USB VCOM Port (COM73)"
What I've tried:-
1. I tried flashing different ROMs compatible with my phone but getting the Brom error s_dl_pmt_err_no_space (5069). So, it is not the problem with the size of ROM, i guess.
1.1 Flashing with "firmware upgrade" option throws "Failed to get PMT info"1.2 Flashing with "download" option says "partition management table is not found. Please use "format+download" option."1.3 Flashing with "format all + download" option throws "Brom error S_DL_PMT_ERR_NO_SPACE (5069)"1.4 When tried to auto format flash (with format flash except bootloader option), it says "S-DL_READ_PT_FAILED(5073)":crying:2. I used different versions of sp_tools from 3.2 to latest version 5. But, still getting the same error with all versions.
3. I tried to readback with sp tools it says OK.
4. When I tried memory test in sp tools with the scatter file of official rom(that was running fine on my phone earlier), it gives error S_DA_SDMMC_WRITE_FAILED (3149) and same old NAND FLASH NOT DETECTED error in the output.
5. But when I flashed only the preloader of the same rom with "format all + download" option, it was formated and flashed successfully.:fingers-crossed: But then try to flash the other files of that same rom, it again shows "Brom error S_DL_PMT_ERR_NO_SPACE (5069)"
6. I don't have Mtk_Droid_Tool backup files for my phone. And it is not detecting my phone.
7. I read other threads on XDA with similar symptoms but no luck.
What should I do now? Help needed.
I tried searching for the solution on the internet continuously for like 4 days and found things that do nothing. Please suggest me what to do? Should I giveup or what? I love my phone very much:crying:. I seriously need your suggestions.:angel: Any help would be highly appreciated.
occurred same problem with my phone canvas 2.2
occurred same problem with my phone canvas 2.2 before 4 days and I am trying to search out any resolution on internet but yet not succeeded; Let's hope someone from XDA will help us in this matter.
mcn18cm said:
occurred same problem with my phone canvas 2.2 before 4 days and I am trying to search out any resolution on internet but yet not succeeded; Let's hope someone from XDA will help us in this matter.
Click to expand...
Click to collapse
fingers crossed
I am facing the same problem! Exactly the same problem with the same device.
Any solution to resolve this error?
Brom error: S_dl_read_pt_fail (5073)
i have the same prlbm .....
do you guyzzz have any solutions...??
I just hard-bricked my phone(Canvas Magnus A117) as well. No luck in finding any solution to this. It was working fine until I decided to reboot it just like that. Got the same errors after trying at the same level.
Same problem happened to my A114
Anyone get their phone rectified?
I had same problem while flashing. I took it to 2-3 places, they said it cannot be rectified. I however did not contact service center. Anyways, did the problem solved for anyone of you
hi friends i am new at this forum and need some help, before this, I usually figured everything out by reading others thread or googling. But now I need your help guys. I recently try to flash my i ball cobalt 4 with the stock rom of the same version [downloaded from needrom.com],But I probably did a mistake and I was messing up with bootloader. The result is that my phone wont even start. No bootloop, no recovery, nothing. Display and everything else remains dead.
At least is phone still detected by computer when I connect it as mtk usb port[it is on META mode now i think]
Also in Smart Phone Flash Tools phone is still visible.
But when I try to flash or format anything it gives me this error message:
It says:
"BROM ERROR: S_FT_ENABLE_DRAM_FAIL (4032)
[EMI] Enable DRAM Failed!
[HINT]: Please check your load matches to your target which is to be downloaded"
I already tried different versions of SPFT and also stock cobalt 4's ROM's from diferrent sources.cleaned mtk deivers many times by using usbdeview according to tutorial. but sadly did not get any success.
My OS is Windows 7x64.
Please guys, this is the first time I'm asking for a help, because I am really desperate and I don't know what else try to make my phone flashable and working again. I googled, searched lot of topics, everything what I was capable to think about. I would be super gratefull for help.
THX guys for your suggestions and help!!!
BTW: I heard some phones can be turned to some kind of "service" bootloader mode with connecting two contacts on main board of phone. Do you know if iball cobalt 4 have this function?
one more thing is that when i selected scatter file first time in spft it gave me an error invalid scatter file so i had to delete scatter file's first line[ie birdtoolminver3.4].so is the scatter file is problem of mentioned error.
I have a problem with my Paris X device. I had an unofficial rom and I wanted to flash the official one. When I started the flashing process with SP flash tool I got this message: "BROM ERROR: S_INVALID_BBCHIP_TYPE (0x3EB)"
Since that my phone is like dead. I cant switch on, I cant either flash again because my driver disappears in 2 seconds and I got the same error everytime.
Please help me, I would really appreciate it. :fingers-crossed:
hi i also bought paris x last year tried to flash it today using sp flash tool with official android 6 rom everything fine until i clicked download...
pmt changed rom - error #1
so then i looked up im supposed to switch to firmware upgrade but that resulted in error
s_invalid_bbchip_type - error #2
now my phone is bricked and whenever i connect it to my pc it appears for about 2 seconds and then disappears...
well im hoping that someone here could actually help cause this is really frustrating and i need to be able to use my phone next week... :/
thanks for replys
same probleme here
invalid bbchip type (0x3eb)
If anyone have this solution, Then please reply
I have also this type of problem In my Intex ace mini mobile
I also experienced problems like that, and couldn't solve it.... ERROR: S_INVALID_BBCHIP_TYPE (1003)
slekdor50 said:
I also experienced problems like that, and couldn't solve it.... ERROR: S_INVALID_BBCHIP_TYPE (1003)
Click to expand...
Click to collapse
Check the scatter, make sure that the line, i.e. matches the device chip type:
platform: MT6735M < -- is this correct?
peti2ty said:
I have a problem with my Paris X device. I had an unofficial rom and I wanted to flash the official one. When I started the flashing process with SP flash tool I got this message: "BROM ERROR: S_INVALID_BBCHIP_TYPE (0x3EB)"
Since that my phone is like dead. I cant switch on, I cant either flash again because my driver disappears in 2 seconds and I got the same error everytime.
Please help me, I would really appreciate it. :fingers-crossed:
Click to expand...
Click to collapse
I think this is scatter file mismatch, because I have done a proper read back of Inew L4 mt6735 to flash it to another phone with exact same model and build. But that flash file is not even working to flash that phone from which I made it giving this same error.
ERROR: S_INVALID_BBCHIP_TYPE (1003)
Still working on it.
[Update]
Only a single "m" in MT6735M in scatter file was missing, now its working all fine. :fingers-crossed:
I searched the whole internet for years to solve this error...
So if your getting this error better check your scatter platform names etc.....bcz even if you get it from readback or official flash files, like in my case it can give you error.
If you're getting this same error every time so try the above advice and here is a tip for early disconnection, connect while holding volume button or open yiu device and find kcolo[\B] and short it with GND.(better find details from google bcz i am too funding it)