Hi volks,
my power button is broken :crying:
but wtf its not only the power button,
one connector on the circuit board is broken... :angel:
I can solder any new power button
Is there a way, to connect a wire to another place on the phone,
to "bridge" the pin?
I can start the phone with volume down, battery out and in,
but i need to connect a switch for fixed car install.
I hope there is a way to connect a wire somewehre on
the circuit board, and install new switch.
(Pic for better illustrating below)
Any Tipps??
Thank you!
Greetings
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Related
HI,
I TRIED TO GO TO BOOTMODE WITH AN HP H6315,
AND I THOUGHT THAT I HAD TO PRESS POWER BUTTON, RESET BOTON AND THE CENTER ONE AT THE SAME TIME, WHAT I GOT AS A RESULT WAS THAT THE PDA DOESNT POWER UP,
I CHECKED INSIDE TO SEE IF THERES ANY INTERNAL BATTERY TO DISCONECT, BUT DIDNT GET ANYTHING,
DOES ANYONE HAS ANY IDEA HOW TO POWER IT UP AGAIN, PLEASE,
AND IF SOMEONE KNOWS HOW TO DO THE UNLOCK PLEASE I WOULD BE VERY PLEASED
Find this button and press:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Then rewrite your post and i might think about reading it.
made me laugh
:lol: @ midget haha!
I'm wondering it anyone knows anything about what appears to be two little buttons on the back of the Galaxy Alpha, after you take the battery cover off. They are to the left of the battery, and are marked "L" and "R." Are these buttons at all, and if so, what do they do? Thanks.
Its not buttons. Under that plugs are some connectors (from ifixit):
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
sqllz said:
Its not buttons. Under that plugs are some connectors (from ifixit):
Click to expand...
Click to collapse
I took a look at a SM-G850A (no little covers over the "buttons" and figured they were connectors. NOW, what are the connectors for?
Dear all,
I lost my cradle and my watch totally powered off now
I have a plan to buy a replacement cradle, but I prefer to make a handmade cradle.
Can someone check where the ground and +5 pin is?
Please take a look this picture (picture credit goes to @phinal post)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
By my guess, GND at pin number 1 after contacting watch body using a multimeter. CMIIW.
Thanks for your help.
Just checked, the bottom pin, #5 in your pic is where the +5 comes from on the cradle
Hello, I did the worst thing possible on one of my devices which was formatting all + flashing a wrong firmware and a bad preloader. Therefore my phone isnt even recognized when i plug it in.
I wanted to try wiring GND to the KCOLO pin cause it supposedly forces a usb connection and therefore I could reflash my phone. However, not all pins on my phone's motherboard are labeled. I took a screenshot, can anyone tell me where I should connect GND to? I cant find the KCOLO pin.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hello guys.
I have an M8S Pro +, when I turned it on, the screen went green and when I tried to use the reset button, I realized that it does not have one.
But, it seems that this (or my?) Box doesn't have a reset button. There is a small hole at the bottom of the box, opposite the LAN and HDMI connectors, but there is no button. I tried a toothpick and an office clip but it just doesn't click.
I proceeded to open it and it has no button anywhere.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Short these two pins in the top left of your picture when plugging in.