Hello guys.
I have an M8S Pro +, when I turned it on, the screen went green and when I tried to use the reset button, I realized that it does not have one.
But, it seems that this (or my?) Box doesn't have a reset button. There is a small hole at the bottom of the box, opposite the LAN and HDMI connectors, but there is no button. I tried a toothpick and an office clip but it just doesn't click.
I proceeded to open it and it has no button anywhere.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Short these two pins in the top left of your picture when plugging in.
Related
This little application I wrote long ago only for myself. I just tried to simulate multitouch control on the classic (non-multitouch) display. Of course, I finally decided that it was impossible.
But I have at least one demo application (which I decided to share) that shows two color blinking rectangles. When you press one of them, it turns off. The point is that when you press the both of them together (or gradually), they turn off both . Just try it. You can release whichever of them and it turns back on, while the pressed one will be still turned off.
To quit, press the right top corner .
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
App can be downloaded here (and it works on all screens).
Hi volks,
my power button is broken :crying:
but wtf its not only the power button,
one connector on the circuit board is broken... :angel:
I can solder any new power button
Is there a way, to connect a wire to another place on the phone,
to "bridge" the pin?
I can start the phone with volume down, battery out and in,
but i need to connect a switch for fixed car install.
I hope there is a way to connect a wire somewehre on
the circuit board, and install new switch.
(Pic for better illustrating below)
Any Tipps??
Thank you!
Greetings
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I'm wondering it anyone knows anything about what appears to be two little buttons on the back of the Galaxy Alpha, after you take the battery cover off. They are to the left of the battery, and are marked "L" and "R." Are these buttons at all, and if so, what do they do? Thanks.
Its not buttons. Under that plugs are some connectors (from ifixit):
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
sqllz said:
Its not buttons. Under that plugs are some connectors (from ifixit):
Click to expand...
Click to collapse
I took a look at a SM-G850A (no little covers over the "buttons" and figured they were connectors. NOW, what are the connectors for?
I got a IPTV box with no remote that says "Cloud Stream TV" on the top. I took it apart, and the motherboard says AMLOGIC S805 BOX V02 and the wifi chip says RTL8188etv. When I plug it in there is a red light, but I plug in a keyboard or mouse and they dont do anything. I see IR reciever but I tried MXQ S805 code from AnyMote app on my S4 and it does not do anything. Is there anything I can do to turn it on?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Figured it out, power supply was bad, new one worked fine. Before only red light was on, I thought red light means standby mode and it needed to be power on.
Hi everyone, I own a Mi Pad 5 pro with the official keyboard. But... I like to use it with a more hard cover, that also has the holes for the keyboard, but of course, they don't touch in any way... Then, I was wondering, that maybe "already exist" (as the cover has the holes for the keyboard) some way to connect them, some kind of cable that connect them, or another way ?
Any ideas ?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Trim the 3 silicone holes and make it one big hole. Use a sharp boxcutter razor.
That should help a lot.