Related
Hi everyone. I have a samsung galaxy s vibrant on android 2.2. I am a total noob with any modifications but am going overseas next month and wanted to unlock my phone. After looking into rooting etc. I downloaded odin and darky's ROM resurrection edition. I followed the prompts to go into recovery and wipe etc. and remove battery and turn back on. After using odin and restarting my phone now just flashes the start screen showing galaxy s GT-I9000. I can't enter recovery mode just download mode. I'm unsure what to do and even tried mounting another recovery file on odin which lead me to the same point. Any help would be greatly appreciated.
Try re-flashing it and see if that works, sometimes that's all it takes. It's possible you just had a bad flash.
I've tried about 5 times now and it seems to keep failing to boot after flash and sticking on the initial boot screen and flashing on and off. Is there a way to download and flash an original ROM and mount on odin to start over?
Try getting into download mode. Hold and continue to hold up & down volume controls while holding in the power button. When the Vibrant logo comes up release only the power button. If you do get into recovery that way scroll down to install zip from sd card and install whatever rom you've got on there that you want to use. Let me know if that works or not.
I can still only get into download mode. I've tried flashing again with both ROMs I have and they both are doing the same thing. Holy frustrating lol
Spike84 said:
I can still only get into download mode. I've tried flashing again with both ROMs I have and they both are doing the same thing. Holy frustrating lol
Click to expand...
Click to collapse
Look for a hard surface... concrete for example.. now take your phone and throw it as hard as you can... Just kidding don't do that, that's a permanent reboot. I know the frustration, I've been there many times. You may want to go back and read through the noob guide, I'm not sure what else to suggest. Hopefully someone else will read this and have a better suggestion. Good luck.
haha yeah the thought crossed my mind. I appreciate your help. I'm still reading through the forum. Most instructions seem to require me to reach recovery mode or usb debugging. My phone is no longer being recognized on the computer but odin is obviously still recognizing so I'm going to try a fresh 2.2 on odin and see if that works.
Good luck, I'm rooting for ya. If that does not work and your close to a T-mobile store I'd just run it in and have them check it out, they may have to replace it.
Thanks again. I'm actually in Canada and using a sub provider from bell "virgin mobile".
I am new to this forum, to fascinate and to root/flash things.
I know about the solution offered at http://forum.xda-developers.com/showthread.php?t=1178544
But it is not working for me because samsungPST is not talking to my phone. I rooted phone with superoneclick and it worked like charm. It has no problem taking to my phone as I have all required drivers. I think may be I need ODIN method to recover instead of SamsungPST. But I dont know anything its just guess.
Here is the thing I want to do:
-My phone is 2.2, ED01, rooted by superoneclick method.
-No partition or flashing is done. It runs same stock android 2.2 though I removed some crappy VZ apps with the help of Titanium Backup.
-Now I want to bring my phone to non-root, 2.2 android, ED05 factory state.
-How can I do so?
I appreciate step-by-step guidance if anyone can provide me.
Use odin instead of samsung pst to flash the ed05 package in the link...follow the steps and your done.
Thanks for quick response.
Please guide me through steps. for example there is pit file in the package, I dont know what to do with it. I am not familiar with ODIN either.
I highly appreciate your time. But PS give me exact step so I can follow it.
dowload odin v1.7 to computer and open program
power off phone and pull battery
plug in usb cable and hold the volume(down) until download mode appears
place the ed05.tar in the pda fiunction(NOT PHONE)
place the atlas 2.2 pit file in the Pit function
click start and it should take 5min
wait for it to say "pass" then "reset" before you unplug the phone
insert battery and reboot
This link will provide you with the files if you dont have em already
http://forum.xda-developers.com/showthread.php?t=1026746
thank you ktulu and droidstyle.
I am doing it rightnow. It says "PASS". Now it is doing nothing. my phone screen appears off.
What next should I do?
You said"Reset" but i did not see that appear.
Hey guys,
Many Thanks for this quick help.
It worked like charm. I am on frech phone. 2.2.2 android ED05.
It was so quick and easy to do after you help me.
Many many thanks.
jasmin9782 said:
thank you ktulu and droidstyle.
I am doing it rightnow. It says "PASS". Now it is doing nothing. my phone screen appears off.
What next should I do?
You said"Reset" but i did not see that appear.
Click to expand...
Click to collapse
I'm assuming you took the battery out when you did the odin process. Place the battery back into the phone and power on.
So I have been told my phone had the wrong firmware installed and I am not even sure where to post this any more...
I have US Cellular as a carrier. and I have the Samsung Galaxy S Mesmeris.
I went to install an update and downloaded the update from the Samsung site and followed the instructions to get to the download mode. was installing it when at like 99% i got an error message. SO I tried it again and same thing. So I downloaded Odin but must of been the wrong once because I redownloaded a different odin and it looks way different the second one has more options where as the 1st one I downloaded and used has only 2. 1) being Start and the 2) being Master Clear.
So I was getting the error that showed a pic of a phone - ! Computer so I read that odin could wipe it and get it back to the way it was.
Well now I am getting nothing but a AT&T World phone screen and it wont even let me get back to the download mode.
I tried every combination with holding the volume button down and up and putting battery in and still just get the AT&T when ever I unplug the USB. Nothing more.
Can anyone walk me through the steps to get it back so it is US Cellular and not showing AT&T?
Someone told me I had the wrong firm ware installed and that it was bricked.
Any help would be great!
xxampdxfatalxx said:
So I have been told my phone had the wrong firmware installed and I am not even sure where to post this any more...
I have US Cellular as a carrier. and I have the Samsung Galaxy S Mesmeris.
I went to install an update and downloaded the update from the Samsung site and followed the instructions to get to the download mode. was installing it when at like 99% i got an error message. SO I tried it again and same thing. So I downloaded Odin but must of been the wrong once because I redownloaded a different odin and it looks way different the second one has more options where as the 1st one I downloaded and used has only 2. 1) being Start and the 2) being Master Clear.
So I was getting the error that showed a pic of a phone - ! Computer so I read that odin could wipe it and get it back to the way it was.
Well now I am getting nothing but a AT&T World phone screen and it wont even let me get back to the download mode.
I tried every combination with holding the volume button down and up and putting battery in and still just get the AT&T when ever I unplug the USB. Nothing more.
Can anyone walk me through the steps to get it back so it is US Cellular and not showing AT&T?
Someone told me I had the wrong firm ware installed and that it was bricked.
Any help would be great!
Click to expand...
Click to collapse
1. Remove battery.
2. Insert battery.
3. While holding down the volume down button plug into usb. It should go into Download mode.
4. If you got into Download Mode, then it is pretty easy from here on. Go into Odin, you can get it from here http://www.mediafire.com/?429fcpdtpckkcea (Link from Droidstyle guide)
You can get the stock mesmerize rom from USCC from here http://android.clocktowergaming.com/mesmerize/Samsung_i500_Mesmerize_EH09.rar
Click PDA and select the rar file and hit start.
If everything goes well, your back on stock where you can go on your way to flashing roms.
Please use the Q&A Forum for questions &
Read the Forum Rules Ref Posting
Thanks ✟
Moving to Q&A
Early yesterday I launched Kies and hit the update firmware option from the tools menu to see if the alleged ICS update was available for my phone. It appeared it was with, a message promoting that it would clear all personal data from the phone, which I then selected cancel so I could do a backup of pictures/videos on the phones internal SD.
Without doing any sort of backup yet I shutdown the phone, only for it to freeze on the shutting down screen. After 20 mins I pulled the battery and let the phone cool down since it had gotten warm trying to shut itself down. After replacing the battery and turning on it was stuck in a bootloop with only the SGS2 logo, never reaching the ATT logo.
At that point I came to XDA, which I frequently browse but have yet to root, and began reading and searching everything I could find.
Hours later I decided to attempt to flash the stock firmware from sammobile.com using Odin. The flash took a long time and I assume never completed. I left it overnight since I didnt want to unplug it mid-flash. Checking back in the morning the phone is black, Odin says failed/disconnected, and I find the battery completely drained. I charged it for a while then tried turning it back on and got the yellow triangle "firmware upgrade encountered an issue..." screen.
Now i'm attempting once more to flash the firmware but again it has been 30 mins on Sbl.bin. I've had a hard time finding stock firmware in different varieties with working links, so to not increase the flash counter in the event I ultimately have to send it in for repair.
Any suggestions on where to go from here? I've followed every direction I can find for flashing stock firmware and nothing has been successful.
Glad to help if I can. Please tell me exactly what package you flashed from sammobile, with a link if possible.
You should change the title of the thread.... I killed my phone. LOL!
http://forum.xda-developers.com/showthread.php?t=1313659
I attempted to flash I777UCKH7, 2011 August, USA (AT&T)
w.sammobile.com/firmware/?page=3&t=1&o=1&m=SGH-I777&r=-1#modelsa
BROKKANIC:
I've tried the steps in that thread, the One-click Oden does not have the phone showing up in any boxes, yet it still shows up in the non-One click Oden.
nett3 said:
I attempted to flash I777UCKH7, 2011 August, USA (AT&T)
w.sammobile.com/firmware/?page=3&t=1&o=1&m=SGH-I777&r=-1#modelsa
BROKKANIC:
I've tried the steps in that thread, the One-click Oden does not have the phone showing up in any boxes, yet it still shows up in the non-One click Oden.
Click to expand...
Click to collapse
Try this.....
2c.) How to root by flashing Entropy512's Return/Unbrick to Stock, Kernel + Rooted System Package with Modem using Odin3 One-Click Downloader (Windows)
Download the "Odin3 One-Click Downloader Stock I-777 UCKH7 with Root no BL" package from Hotfile. Extract the contents of the zip file to a directory on your hard disk drive. This is a One-Click version of Entropy512's Return/Unbrick to Stock, Kernel + Rooted System Package plus stock modem from the development forum. (Contains stock zImage, factoryfs.img with root, and modem.bin.)
Start the Odin3 One-Click Downloader program by double clicking on "I777UCKH7 OCD With Root.exe".
Now Enter Download Mode:
With the phone powered off, plug in the usb cable while holding the vol up + vol down buttons (but not the power button).
When the warning screen appears, press Volume up to continue into download mode.
In Odin, the small edit box in the upper left corner will turn yellow, and say something like [0:COM8]. The number could be different.
Click Start. Watch the progress bar advance in green while the message box in the lower area describes the steps. When the flash is finished, the top left larger edit box will turn green and say PASS! and your phone will automatically reboot.
Unplug the usb cable from you phone after it boots up. Success. You're Rooted.
SOURCE: http://forum.xda-developers.com/showthread.php?t=1311081
creepyncrawly would know better. It's his thread.
Download the file from below post to go back to stock I777UCKH7. Follow the instruction written in the post. I just had the same a while ago using the mobile odin to go back to stock. Got stuck on Samsung Galaxy SII screen. Pulled the battery and then followed the instructions from this post. I selected the one that says no BL 'I777UCKH7 OCD No BL'.
http://forum.xda-developers.com/showpost.php?p=18859438&postcount=199
Once you are done with the stock restore. To upgrade to ICS LE5 follow the instructions from below post. Make sure you read and follow the instructions as mentioned in the post.
http://forum.xda-developers.com/showpost.php?p=27707563&postcount=83
nett3 said:
I attempted to flash I777UCKH7, 2011 August, USA (AT&T)
w.sammobile.com/firmware/?page=3&t=1&o=1&m=SGH-I777&r=-1#modelsa
BROKKANIC:
I've tried the steps in that thread, the One-click Oden does not have the phone showing up in any boxes, yet it still shows up in the non-One click Oden.
Click to expand...
Click to collapse
You downloaded I777UCKH7_I777ATTKH7_ATT and extracted I777UCKH7-rev02-home-low-cl503881.tar.md5?
Flashed the .tar.md5 in the pda slot?
What version of Odin are you using?
Edit: You're getting lots of advice here. Let me know if you need me to help troubleshoot your issues.
BROKKANIC/krips2003: Thanks for helping so far, but no luck. Those both link to the same Odin One click. This and another one click I tried do not show the phone connected to any COM#. But, in the non-one click Oden the phone shows up. I have pulled the battery and changed USB ports and it still will not show up in the one click.
In the mean time I'll see if there's a solution for that, but I'd like to hear any other suggestions.
Edit: I get the feeling Odin is not starting the write process, since neither the progress bar or words show up in the box above COM# until AFTER I unplug the phone, at which time it flashing quickly then displays Failed.
nett3 said:
BROKKANIC/krips2003: Thanks for helping so far, but no luck. Those both link to the same Odin One click. This and another one click I tried do not show the phone connected to any COM#. But, in the non-one click Oden the phone shows up. I have pulled the battery and changed USB ports and it still will not show up in the one click.
In the mean time I'll see if there's a solution for that, but I'd like to hear any other suggestions.
Edit: I get the feeling Odin is not starting the write process, since neither the progress bar or words show up in the box above COM# until AFTER I unplug the phone, at which time it flashing quickly then displays Failed.
Click to expand...
Click to collapse
Try using another micro usb wire if you have one. If not then get one from radioshack or bestbuy. I had the almost similar issue on my captivate with the original USB cable. Then I got a Rocketfish one from bestbuy and it worked like a charm.
I'm sure you might have already done this. Make sure you first run the ODIN and then put your phone in download mode.
krips your a genius!
The one click is now working thanks to the suggestion to pay attention to order of operations. I must have never plugged the phone in AFTER starting the one click. This was easily overlooked when I've been switching the phone between 2 PCs and 3 micro usb cables.
I now have a progress bar and have had made more progress than in the last 24 hours. Even after searching I did not find this solution, even though it's stated in the directions and it seems trivial, maybe it should be emphasized the one click needs to phone plugged in after it's running.
Thanks again. I'll update this post when it's back to being a phone again.
PS. BROKKANIC: you were right, if I didn't kill my phone then I sure was the impeding factor in its recovery.
Good news/bad news. Still stuck in bootloop, but now have SGS2 logo instead of yellow triangle. Trying to enter recovery mode crashes the phone soon after it appears.
Is this a bootloader problem, kernel problem, or something else?
LOL!. Glad you got it working.
nett3 said:
Good news/bad news. Still stuck in bootloop, but now have SGS2 logo instead of yellow triangle. Trying to enter recovery mode crashes the phone soon after it appears.
Click to expand...
Click to collapse
Flash back to stock first.
BROKKANIC said:
LOL!. Glad you got it working.
Flash back to stock first.
Click to expand...
Click to collapse
I believe that what I have been doing. I ran I777UCKH7 OCD With Root.exe, which resulted in bootloop, then ran I777UCKH7-CL503881-No-BL.exe, which also resulted in bootloop. Both completed successfully, but resulted in the same bootloop.
Odin appears unable to flash anything without it being a one click. I'm trying to flash Siyah-v2.6.14-att.tar. But Odin hangs at zImage with no progress bar.
What operating system you using: if windows 7 are you running as administrator ?
hd779 said:
What operating system you using: if windows 7 are you running as administrator ?
Click to expand...
Click to collapse
I've resorted to my WinXP laptop which has been more successful than my Win7 desktop. On the Win7 attempts everything is run as admin, but has many time bluescreened and hard reset the whole PC when attempting to flash anything with Odin. Maybe a separate issue, maybe not. But the XP machine is atleast successfully flashing the Odin one clicks.
Update: Odin standalone (non-one click) appears to be unable to flash anything, it will only hang when trying to write. One click Oden packages seem to work. Is there a one click with full stock sbl, param, kernel, etc?
I think your problem is you flash to stock with packet include bootloader, so that is the reason why your phone is brick.
I'm using this: http://forum.xda-developers.com/showthread.php?t=1691659 for stock UCKH7. This is non-root version and work very well for me. It include sbl, kernel and param, ...
gefox4vn said:
I think your problem is you flash to stock with packet include bootloader, so that is the reason why your phone is brick.
I'm using this: http://forum.xda-developers.com/showthread.php?t=1691659 for stock UCKH7. This is non-root version and work very well for me. It include sbl, kernel and param, ...
Click to expand...
Click to collapse
I haven't flashed a package with a bootloader yet. The only ones that work for me are Odin one click packages, and the two I've tried do not have bootloaders. I've been looking for one WITH a bootloader but no such luck yet, since maybe that would solve the problem.
The guide/link you've suggested will not work for me at this time. I do not have the ability to boot into any andriod OS. The only capability my phone has is executing Odin one click packages for some reason, even Oden standalone firmware flashes do not work.
I had a similar issue...I eventually got mine stuck at the ATT droplets....
Finally I flashed back to 2.3.4 stock....did the ota...then upgraded to ICS.
Its all on my work laptop so I wont be able to post any specific files or their names until monday...
Good luck!
Once your phone gets to the boot screen try to get into stock 3e (both volume buttons + power till 2nd SGSII splash screen) recovery and do a factory reset. Should boot after that. Good luck.
Sent from my SAMSUNG-SGH-I777 using xda premium
Why not try a custom ics rom? What else do you have to lose? Staying stock is overrated anyways. You may also have an antivirus stopping Odin but I doubt it. Just turn off your antivirus and try.
Sent from my SGH-I777 using xda premium
Alright, so here's my problem:
I just upgraded to the Galaxy S III yesterday, and today decided to try to 'root' the device. So I found the Toolkit here on XDA (from here), and went through the initial steps without any issues (driver installation, device recognition, etc..).
I then went to the 'rooting option' menu, where I selected the first--and most basic --option, which was to only install Super User, and the push the permissions.
I was following the automated guide, opened Odin, selected the correct file, 'boot-insecure-i9300xxale8-gsm.tar', and made sure only 'auto-restart' and F.reset time' were checked, and clicked 'start'. The flash appeared to have gone well, but when it tried to restart, the phone never rebooted. I attempted to reboot into download mode (Vol. Down + Home + Power), but the device was unresponsive. I then browsed around the forums a bit looking for other methods, including taking the battery out for several minutes, then putting it back in whilst holding down the 'download mode' button combination, and other various variations of that method; yet again, none prevailed.
The device gives no indicator lights when plugged in, no light up when the power button is held down, and is overall seemingly unresponsive. However, when I hold down the 'home' button alone - after about 30 seconds - a green vertical battery appears on the screen, with a little white loading indicator on it, but vanishes after about 5 seconds or so, and the device becomes unresponsive once more.
The device is not being recognized by my computer whatsoever, no beeps or anything when plugged in.
Any ideas as to what I can do?
EDIT: I have been able to get into 'Download mode' somehow, but after trying to reflash the stock rom, it went back to the 'Unresponsive' mode. I have it in Download mode again currently, so what do I do from here?
I assume it is still under warranty, since it is less than a few days old. Return it to the store claiming hardware malfunctioning.
Forget about the toolkit. In my opinion, it's quite useless (as you know by now), and it tends to automate tasks that are simple by nature.
Even although I appreciate the effort the developers of the toolkit put into it, I would never do it, since I want to have control of the entire process: I want to know exactly what is being done and why, and that is something the Toolkit won't give me.
If you want to root your phone and keep it stock, do this:
- Install the drivers for the device.
- Install SiyahKernel for S3 version 1.3 using ODIN.
- Install superSU (from market) and let it update it's binary su
- Install MobileOdin (free version)
- download the latest Samsung ROM (such as DBT [Germany] or ITV [Italy]) using CheckFus downloader
- copy the downloaded and unzipped ROM to your phone's external SD card (just the .md5 file)
- using MobileODIN, flash the ROM and select the "EverRoot" feature
- after reboot the ROM will be updated, stock, but with root
- Install TriangleAway to get rid of any annoying triangles and to reset the binary counter
Done. supposing the ROM is already downloaded, the entire process takes exactly 4 minutes.
Simonetti2011 said:
I assume it is still under warranty, since it is less than a few days old. Return it to the store claiming hardware malfunctioning.
Forget about the toolkit. In my opinion, it's quite useless (as you know by now), and it tends to automate tasks that are simple by nature.
Even although I appreciate the effort the developers of the toolkit put into it, I would never do it, since I want to have control of the entire process: I want to know exactly what is being done and why, and that is something the Toolkit won't give me.
If you want to root your phone and keep it stock, do this:
- Install the drivers for the device.
- Install SiyahKernel for S3 version 1.3 using ODIN.
- Install superSU (from market) and let it update it's binary su
- Install MobileOdin (free version)
- download the latest Samsung ROM (such as DBT [Germany] or ITV [Italy]) using CheckFus downloader
- copy the downloaded and unzipped ROM to your phone's external SD card (just the .md5 file)
- using MobileODIN, flash the ROM and select the "EverRoot" feature
- after reboot the ROM will be updated, stock, but with root
- Install TriangleAway to get rid of any annoying triangles and to reset the binary counter
Done. supposing the ROM is already downloaded, the entire process takes exactly 4 minutes.
Click to expand...
Click to collapse
Thank you so much for responding!
I have the phone in download mode right now though, as I've been able to get that far. Is there anything I can do from here to fix the issue? I really don't want to take it back up, and face the chance of confrontation if they decided to call me out on the issue.
I tried flashing the Sinyah Kernel via Odin just now, using the PDA mode, but once again, just flashes the Samsung logo for a brief second, and disappears, leaving me with a black screen.
Samsung don't seem to really care if you have rooted or not, so far about 4 people in 2 days on this and other for mums have returned phones because they have possibly bricked them, all got them exchanged with out a problem.
To unroot and return your galaxy S3 to stock for warranty watch this. http://www.youtube.com/watch?v=_8Tga_yKywc&feature=youtube_gdata_player
Zenno said:
Thank you so much for responding!
I have the phone in download mode right now though, as I've been able to get that far. Is there anything I can do from here to fix the issue? I really don't want to take it back up, and face the chance of confrontation if they decided to call me out on the issue.
I tried flashing the Sinyah Kernel via Odin just now, using the PDA mode, but once again, just flashes the Samsung logo for a brief second, and disappears, leaving me with a black screen.
Click to expand...
Click to collapse
Flash a stock rom for your phone and location or if it was a branded phone flash that .
Even if it does not boot you stand a better chance under warranty .
Say you where doing a Kies update and it just failed to reboot .
jje
JJEgan said:
Flash a stock rom for your phone and location or if it was a branded phone flash that .
Even if it does not boot you stand a better chance under warranty .
Say you where doing a Kies update and it just failed to reboot .
jje
Click to expand...
Click to collapse
I tried to reboot the stock firmware 'boot-stock-i9300xxale8-gsm.tar', but when Odin failed to reboot the phone, and I manually put it back into download mode, it still said my binary was 'Custom'.
Should I be trying to flash that under 'Bootloader' in Odin or something? Because I've been doing 'PDA' and it hasn't been working.
Download an original, stock ROM from samsung-updates.com or use checkFus downloader.
That is what you'll flash.
This is the one I use: http://samsung-updates.com/get/1932/Samsung_Firmware_GT-I9300_DBT_I9300XXALF6_Android_4_0_4.html
After some further browsing, I was able to fix it thanks to this post here, posted by 'mskip'.
Whew! That was stressing. Thanks guys for helping out though!
How to get out of hard brick to download mode
Zenno said:
After some further browsing, I was able to fix it thanks to this post here, posted by 'mskip'.
Whew! That was stressing. Thanks guys for helping out though!
Click to expand...
Click to collapse
After hardware brick, how did you get it back to download mode agian?
i cnat do anything , no turn on no charging, nothing, how you do it?
i think if i can get it back to dowload mode, i can flash out the stock rom again.
any advise will help
Pull the Batteery
jiafu790617 said:
After hardware brick, how did you get it back to download mode agian?
i cnat do anything , no turn on no charging, nothing, how you do it?
i think if i can get it back to dowload mode, i can flash out the stock rom again.
any advise will help
Click to expand...
Click to collapse
Remove the battery for about 2 minutes, replace it and immediately try to go into download mode. This worked for me
same problem
Hard bricked it too, flashed a wrong rom made for international model, i have the att model are you sure taking out the battery works?
Zenno said:
EDIT: I have been able to get into 'Download mode' somehow, but after trying to reflash the stock rom, it went back to the 'Unresponsive' mode. I have it in Download mode again currently, so what do I do from here?
Click to expand...
Click to collapse
I have the same problem! Do you know how you got into download mode?
Surge411 said:
I have the same problem! Do you know how you got into download mode?
Click to expand...
Click to collapse
Just keep trying,I must have removed the battery and pressed the buttons over six times to get into download mode. Hope you get there.