[Q] My experiments with e970 and unanswered questions..!! - AT&T LG Optimus G

First upon there are few senior guys in here who hates noobs questions, to them " Don't forget you too where a nobiee in the beginning."
NOw my story!!
2 weaks before I brought one unlocked E970 from my friend, which runs CM11 nightly 13. The first thing I did was updating to 14 which was just released. The phone had little heating problems and gps fixing issue, also terrible battery backup due to wake locks.
So I flashed the cm 10.2 stable and found all issues fixed except the phone fails not register in 900mhz 2G networks in India (I mean weak signal in 900mhz, where other carriers like DOCOMO which works on 1800mhz are works just fine).
After reading a lot I decided to flash on nexus 4 radio (.54),but there is no hope.
Then I flash back the stock ATT_JB radio and find the network problem is resolved have all frequencies (900/1800mhz gsm) and carriers listed, but my sim is not recognizing.
Ok good, I start flashing almost every radio up there
E970,e971,e973,e977 - all gives the No sim error. ( even on LS970) ( surprisingly the all shows the same baseband also)
but all the nexus 4 radios did works, but terrible signal in GSM 900mhz. ( also experience few problems in .84 and above)
Guys I even flashed on E980 modem and find the network and SIM works amazing but no audio, speaker and demigod crash. Which can be understood since e980 is snapdragon 600 SOC.
OK I must have broke some thing lets go to the beginning, so I did the LGNPST and return my phone to 4.1.2 stock att&t.
results -- Stock rom and stock rado
problems-- not even network scan is working( error in scanning network), and of curse no SIM!!!
That's it> I rooted my phone by using freegee unlocked my boot loader and install CWM. Then flashed back the CM11 and nexus radio. Atleast the phone is working expect the volume keys are inverted.
I may have broke the EFS, but I have IMEI number and phone working in N4 modem. So the issue is with the ATT radio which may be some RIL issue I guess.
In order to get my phone useful, either I have to make the ATT radio accpet my SIM or some have edit the nexus4 radio and make it give a good signal in gsm 900mhz. Also the inverted volume keys are awkward.
To be honest I have no idea what to do next, but I strongly feels its a software error and can be fixed, BUT HOW?

harirajrin said:
First upon there are few senior guys in here who hates noobs questions, to them " Don't forget you too where a nobiee in the beginning."
NOw my story!!
2 weaks before I brought one unlocked E970 from my friend, which runs CM11 nightly 13. The first thing I did was updating to 14 which was just released. The phone had little heating problems and gps fixing issue, also terrible battery backup due to wake locks.
So I flashed the cm 10.2 stable and found all issues fixed except the phone fails not register in 900mhz 2G networks in India (I mean weak signal in 900mhz, where other carriers like DOCOMO which works on 1800mhz are works just fine).
After reading a lot I decided to flash on nexus 4 radio (.54),but there is no hope.
Then I flash back the stock ATT_JB radio and find the network problem is resolved have all frequencies (900/1800mhz gsm) and carriers listed, but my sim is not recognizing.
Ok good, I start flashing almost every radio up there
E970,e971,e973,e977 - all gives the No sim error. ( even on LS970) ( surprisingly the all shows the same baseband also)
but all the nexus 4 radios did works, but terrible signal in GSM 900mhz. ( also experience few problems in .84 and above)
Guys I even flashed on E980 modem and find the network and SIM works amazing but no audio, speaker and demigod crash. Which can be understood since e980 is snapdragon 600 SOC.
OK I must have broke some thing lets go to the beginning, so I did the LGNPST and return my phone to 4.1.2 stock att&t.
results -- Stock rom and stock rado
problems-- not even network scan is working( error in scanning network), and of curse no SIM!!!
That's it> I rooted my phone by using freegee unlocked my boot loader and install CWM. Then flashed back the CM11 and nexus radio. Atleast the phone is working expect the volume keys are inverted.
I may have broke the EFS, but I have IMEI number and phone working in N4 modem. So the issue is with the ATT radio which may be some RIL issue I guess.
In order to get my phone useful, either I have to make the ATT radio accpet my SIM or some have edit the nexus4 radio and make it give a good signal in gsm 900mhz. Also the inverted volume keys are awkward.
To be honest I have no idea what to do next, but I strongly feels its a software error and can be fixed, BUT HOW?
Click to expand...
Click to collapse
you done lots of wrong things with your phone for minor network issue.
First flash Stock LGNPST to make your phone usable. And then use it for about a day. sometimes due to low signal it doesn't network.
If still doesn't work then flash EFS and Stock ATT JB modem and then try to use it.
or ask your friend if he gave you and unlocked phone or locked one or he might have bricked modem just like you are trying todo.
Flashing files for diff in your phone makes things worse and might give you Hard brick. so never flash anything of other phones. NEVER.
Your best bet is to use stock rom for a while to make things normal or else you might hard brick your phone and also if you are buying phone from someone else then first check it if everything works or not.

I DID TRIED lgnpst
ShoaibAhmed said:
you done lots of wrong things with your phone for minor network issue.
First flash Stock LGNPST to make your phone usable. And then use it for about a day. sometimes due to low signal it doesn't network.
If still doesn't work then flash EFS and Stock ATT JB modem and then try to use it.
or ask your friend if he gave you and unlocked phone or locked one or he might have bricked modem just like you are trying todo.
Flashing files for diff in your phone makes things worse and might give you Hard brick. so never flash anything of other phones. NEVER.
Your best bet is to use stock rom for a while to make things normal or else you might hard brick your phone and also if you are buying phone from someone else then first check it if everything works or not.
Click to expand...
Click to collapse
I did tried the stock and the modem flashes.. finally I sold it .

Related

Atrix keeps restarting when making a phonecall

ok this phone a brand new, i can receive calls and text but when i dial a number and try to make a call the phone restarts
This is factory unlocked and not rooted
Try flashing a newer radio rom.
I dont want to root it incase i cant get the original rom back.
It is weird as, i have tried with every sim card to make calls and it works but when i put the 3 sim in does plays up
We experienced the same issue on some Turkish networks as well and flashing a newer radio rom fixed the problem. Flashing roms and rooting are totally different. What you need is a newer version of your current baseband ( radio rom ) sbf and official motorola software flasher " RSD Lite 5.3 "
Hope it helps.
Thank you so much for that Semseddin.
My problem solved, i just flashed it using RSD lite 4.9
Thanks everyone
Hi. I've been having the exact same issue. I've got an unlocked AT&T Atrix and I'm trying to use a Three UK sim (I'm in the UK). I'm a bit new to the world of android, can someone post a link to an appropriate Radio Rom?
Thanks for any help!!
OK after a little more web searching I've found a (sort of) solution -
"Here's a quick fix for it thou, (not permanent)....
1. type *#*#4636#*#* on the dialer
2. Chose Phone Information
3. Set preferred network to GSM only
Viola...its fixed
problem with this fix is that you wont be able to use your 3G network but the dialer should be working."
Problem is of course that you can't use your 3G connection. Hope this helps anyone else with the same issue.
Link to article - https : // supportforums.motorola .com/message/379232
Why is it always 3 that cause a problem?
When the Nokia N900 came out, that wouldn't work with 3 initially until a couple of updates later!
lowndes783 said:
OK after a little more web searching I've found a (sort of) solution -
"Here's a quick fix for it thou, (not permanent)....
1. type *#*#4636#*#* on the dialer
2. Chose Phone Information
3. Set preferred network to GSM only
Viola...its fixed
problem with this fix is that you wont be able to use your 3G network but the dialer should be working."
Problem is of course that you can't use your 3G connection. Hope this helps anyone else with the same issue.
Link to article - https : // supportforums.motorola .com/message/379232
Click to expand...
Click to collapse
May not work for Pay as you go? I didn't think that it had 2G fall back?

Baseband Problems, Need help

I have been hunting around, trying to find a solution
I am having XT-912 Verizon Droid Razr Maxx model, and i am in India using a GSM network.
All cdma roms, dont show gsm signal bars, hence i am using patch to enable gsm using coupe of build.prop entries. [Src: http://www.internauta37.altervista.org/how-and-patch-fully-enable-gsm-verizon-cdma-phones-android]
Everything works well, but the main problem is whenever i move from one area to another, many times phone loses signal and doesnt re-connect for a loooong time.
It gets very irritating as i have been missing calls, msgs, etc
1. The problem wasnt there initially and i feel some junk data or cache in baseband might be causing it?
2. I think the problem might be a ril or baseband mismatch. I am on cdma_n_05.21.00R which is latest baseband, any idea if trying different basebands might help solve this proble,?
3. Also is it possible to flash older baseband [ics or gb or older jb] on my phone to check compatibility or will i cause brick or locking etc?
Also i read about CID, and its something about region secific identifier, so anything about that affecting my device?

Odd Problem: WiFi On=Network like"OFFline" but with signal...

Hi dudes,
i have a normal GT-i9300 NO BRAND. From the beginning i started with Ultima Rom and until version 12 and a provider CHANGE with the same number (from Wind to TIM, Italy) i never had a problem...after,starts the odd's show:
if turns on the WiFi...my device is like OFFLINE,is not reachable .KEEP ATTENTION: the signal is present, like -85dbM 14asu.But from the moment I do a phone call or i send a SMS...device turns back reachable, for a X period of time,after that: "offline" again.
I tried:
change modem (latest,oldest...)
downgrade of Ultima Rom and modem
upgrade until Ultima Rom V16 (4.3..)
pass to CM11 temasek unofficial V45 (4.4.2 GREAT ROM...)
pass to STOCK SAMSUNG ROM (with odin,latest version...my God,tried only for the test and quickly raging i came back to temasek)
used the same device with a different TIM sim
I did a deep wipe for new ROM installation,with Philz recovery...
NOTHING WORKS, the problem rest.
To Do:
try a different provider sim...for example WIND or 3 (for exclude a Provider problem...something related to communication protocols)
Try my TIM sim in another GT-I9300 always with CM11 temasek unofficial.(for exclude an HARDWARE problem...waiting for a my friend with the same device and rom)
Weird:
it seems that this problem is only in my home because from my workplace (another radiocell) i'm reachable also under wifi connection.
CALLED:
I called to my customer service TIM and they did a "format" of my sim and "account"...but nothing changes. They said that in my radiocell the signal is weak, they know that but they can't do nothing.
I REMEMBER that the problem began from the SWITCH from WIND to TIM,that not wanted,happened during an upgrade of Ultima ROM...
SO,the problem is of my device? Sim? Number? Provider?... WHAT THE H****?!
ANY SUGGESTIONS!?!??!
Skyfinder said:
Hi dudes,
i have a normal GT-i9300 NO BRAND. From the beginning i started with Ultima Rom and until version 12 and a provider CHANGE with the same number (from Wind to TIM, Italy) i never had a problem...after,starts the odd's show:
if turns on the WiFi...my device is like OFFLINE,is not reachable .KEEP ATTENTION: the signal is present, like -85dbM 14asu.But from the moment I do a phone call or i send a SMS...device turns back reachable, for a X period of time,after that: "offline" again.
I tried:
change modem (latest,oldest...)
downgrade of Ultima Rom and modem
upgrade until Ultima Rom V16 (4.3..)
pass to CM11 temasek unofficial V45 (4.4.2 GREAT ROM...)
pass to STOCK SAMSUNG ROM (with odin,latest version...my God,tried only for the test and quickly raging i came back to temasek)
used the same device with a different TIM sim
I did a deep wipe for new ROM installation,with Philz recovery...
NOTHING WORKS, the problem rest.
To Do:
try a different provider sim...for example WIND or 3
Try my TIM sim in another GT-I9300 always with CM11 temasek unofficial.(waiting for a my friend with the same device and rom)
Weird:
it seems that this problem is only in my home because from my workplace (another radiocell) i'm reachable also under wifi connection.
CALLED:
I called to my customer service TIM and they did a "format" of my sim and "account"...but nothing changes. They said that in my radiocell the signal is weak, they know that but they can't do nothing.
I REMEMBER that the problem began from the SWITCH from WIND to TIM,that not wanted,happened during an upgrade of Ultima ROM...
SO,the problem is of my device? Sim? Number? Customer?... WHAT THE H****?!
ANY SUGGESTIONS!?!??!
Click to expand...
Click to collapse
my guessing is that the problem is the sim card, probably damaged. you should try another sim card.
done yet, I wrote it I the "tried list" ... Another tim sim and the problem rest
Sent from my GT-I9300 using xda app-developers app
Skyfinder said:
done yet, I wrote it I the "tried list" ... Another tim sim and the problem rest
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
yeah sorry, it was late and i was tired, didn't see that. well, it might be the antenna of the phone, you should go to a gsm service, they have the necessary stuff to point out the problem, even if it's hardware or software.
Could even be the sim holder .
I'm thinking that is an ANDROID or Modem problem related...specially with TIM communication protocols.
Is like if where there is a low signal,and you use Wi-Fi...device don't give energy to radio antenna,but to wi-fi. When you call or sending SMS,the antenna takes more power and the device is now reachable...
I should try a real old ROM with a real old modem...ufff...is all so boring -.- (i know,exist nandroid,but still boring is!)
Skyfinder said:
I'm thinking that is an ANDROID or Modem problem related...specially with TIM communication protocols.
Is like if where there is a low signal,and you use Wi-Fi...device don't give energy to radio antenna,but to wi-fi. When you call or sending SMS,the antenna takes more power and the device is now reachable...
I should try a real old ROM with a real old modem...ufff...is all so boring -.- (i know,exist nandroid,but still boring is!)
Click to expand...
Click to collapse
if you have a rom with modem that changed your efs partition to efs v2 and try to flash a rom that has modem with efs v1 you will loose your IMEI and S/N , unless you have a backup of efs v1.
darkmage93 said:
if you have a rom with modem that changed your efs partition to efs v2 and try to flash a rom that has modem with efs v1 you will loose your IMEI and S/N , unless you have a backup of efs v1.
Click to expand...
Click to collapse
THANKS FOR REMIND ME THAT! I've the back up of old IMEI and S/N Really thanks!

SIM not working?

Anyone have the issue where the SIM card isn't recognized? I'm on the RR newest ROM and the card isn't being recognized...I'm about to try the stock ROM and see how that goes.
Similar problem
I`m in a similar position I think. However, my phone recognizes the SIM but when checking the SIM-status the mobile radio seems to be off. I canĀ“t change preferred network type, it just jumps back to "TD-SCDMA/GSM/WCDMA/LTE , I get no results when searching for mobile networks and when I use the *#*#4636#*#* - menu the "Turn on radio"-option wont respond. I`m on latest stock firmware and the phone is still displaying IMEI-numbers. I bought my unlocked European version of Oneplus X yesterday on an auction site, the seller has good reputation and he claims that it worked fine for him. I got a new SIM-card today thinking that would have solved the problem, no luck there however. I also did a hard reset and downgraded to an earlier version of a stock firmware and the error is still there. I noticed I had TWRP v.2.8.7.0 blu_spark r5 preinstalled when I bought it, its a custom kernel right? Could something related to the kernel be the root of the problem or the baseband? Any suggestions on what to do next?

Only 2G on SIM1 now

For the last two or three days, my RN3 has only been connecting to 2G networks. I understand there can be issues with this in SIM2 slot (which I experienced last week), whereas SIM1 should work fine.
Anyway, after moving the sim card from SIM2 to SIM1 last week, I enjoyed 3G networks for a few days, but now it's been on 2G only. I've tried several reboots in the meantime, and the phone was off and on as well, nothing helped. Is there any known way to resolve this? I'm running latest stable CM13 (and the only other issue since day one has been no front cam).
Did you tried a factory reset?First make a back-up,because this procedure will delete all data and apps from your internal partition.
Have checked your sim card in other phone to see if it does persist connection issue?How is signal metter in your area?
For the last two or three days, my RN3 has only been connecting to 2G networks. I understand there can be issues with this in SIM2 slot (which I experienced last week), whereas SIM1 should work fine.
Anyway, after moving the sim card from SIM2 to SIM1 last week, I enjoyed 3G networks for a few days, but now it's been on 2G only. I've tried several reboots in the meantime, and the phone was off and on as well, nothing helped. Is there any known way to resolve this? I'm running latest stable CM13 (and the only other issue since day one has been no front cam).[/QUOTE]
For me, what worked was not flashing the recommended CM13 firmware. From MIUI, just flash the recovery, then CM, Gapps, done.
I get 3G now, fingerprint etc all work fine. This isn't supported by the devs but it works for me, so...
For the record, I was on the MIUI 8 Global Dev ROM when I flashed this.
@Luiggi79 - No, but I'm about to do it (and also try some other things) this weekend if I have time.
@NSDCars5 - Did you unlock "officially"? I have the "permit" to do it now, but I have to put everything back to "factory" state first (just not sure at this moment if the global ROM, which was there when I bought it, now supports official bootloader unlock or not - I believe it used to only work on Chinese MIUI ROM).
@Luiggi79 - No, but I'm about to do it (and also try some other things) this weekend if I have time.
@NSDCars5 - Did you unlock "officially"? I have the "permit" to do it now, but I have to put everything back to "factory" state first (just not sure at this moment if the global ROM, which was there when I bought it, now supports official bootloader unlock or not - I believe it used to only work on Chinese MIUI ROM).
I haven't unlocked my device bis yet because i don't need it.I saw somewhere on MIUI website that the unlocking process have nothing to do with the ROM version:global,china or developer.
Which ROM do you have installed on the device?If you have custom ROM and custom recovery image do a search for guides,to revert all "things"to factory state.Be careful if you are on custom rom,because you need to do some procedures before MIUI original ROM install;otherwise you will get a bricked device.Search and read before any action
galadroid said:
@Luiggi79 - No, but I'm about to do it (and also try some other things) this weekend if I have time.
@NSDCars5 - Did you unlock "officially"? I have the "permit" to do it now, but I have to put everything back to "factory" state first (just not sure at this moment if the global ROM, which was there when I bought it, now supports official bootloader unlock or not - I believe it used to only work on Chinese MIUI ROM).
Click to expand...
Click to collapse
galadroid said:
@Luiggi79 - No, but I'm about to do it (and also try some other things) this weekend if I have time.
@NSDCars5 - Did you unlock "officially"? I have the "permit" to do it now, but I have to put everything back to "factory" state first (just not sure at this moment if the global ROM, which was there when I bought it, now supports official bootloader unlock or not - I believe it used to only work on Chinese MIUI ROM).
Click to expand...
Click to collapse
Yep, I unlocked officially. Unlock definitely works on Global ROMs too, I unlocked mine on Global Developer.
Well, after wiping it and flashing Santhosh CM and official CM13 - 3G worked on both. (Also, front cam works in Santhosh CM, but not in the official CM13.)
It would be great to know what the reason for 2G was... the manual network scan then only displayed 2G and 4G networks from all available operators, but no 3G anywhere. I hope Privacy Guard or AfWall weren't interfering there.

Categories

Resources