This is what i did
OK i ve been trying to flash a new custom rom on my Xperia P, i looked at a number of guidelines and doing things step by step.
Since im very new to this i downloaded a few Roms. I was following the guide "http://droidors.com/2014/07/08/update-xperia-p-lt22i-to-android-4-4-4-kitkat-with-slimkat-custom-rom/2/" and everything was going fine. I reached the step to "fastboot flash boot boot.img", i did that and then went on the next step to boot in CWM Recovery and install the zip rom and the Gapps. During the Zip Rom install i got status 7 error.
Now, i noticed that i might have flashed the wrong Rom so rechecked the guide and installed the correct Rom which is mentioned in "http://forum.xda-developers.com/xperia-u/p-development/rom-slimkat-4-4-2-release-candidate-t2657795" . But now THE PROBLEM IS, AFTER I FLASHED THE INCORRECT IMG, MY PC IS NOT RECOGNISING THE XPERIA P SAYING IT DOESNOT RECOGNISE THE DRIVERS, therefore im not able to copy the ROM Zip on the SDcard, to then run it from CWM.
After I flashed the SlimKat Rom, and things went out of hand ( till this point i could see Slimkat logo at boot and could also go in CWM Recovery ), I tried to restore through Nandroid Backup i had done. As soon i selected the restore option and then the backup file, within 2-3 seconds the phone went off, and then on boot all i can do is see "SONY" on screen. Nothing else happens. i cannot even go in CWM now, its just stuck on "SONY"
I then tried to flash the stock Rom through this link "http://forum.xda-developers.com/xperia-u/p-development/ftf-firmware-xperia-p-generic-world-t2322163", through flashtool to bring my phone back to life. I installed the drivers as per instructions from drivers folder, but for some reason the pc is just not accepting. I did install the drivers through this exact method yesterday night and it worked perfectly.
I have tried all this on a different machine, different cables and ports, but still the issue persists
Please suggest. I hope im asking at the right place.
Kindly advise, im stuck with no spare phone.
Related
Ok, so I have been running a Honeycomb rom but wasnt happy with it so I decided to try a different one. In the Roms directions, it said to be on a stock 1.2 rom. So I downloaded the one from its instructions and flashed. All went well, it booted into the stock rom with no problem. So I put the new HC rom on my sd and renamed to update.zip. I booted into recovery and noticed that the recovery was reverted back to the stock recovery. I thought, no big deal, Ill just flash the rom from that recovery. Well it kept aborting the install for some reason. Doesnt give an error, just says installation aborted. So I figured it was the recovery that was the problem. I downloaded CWM 0.8 and followed instructions, put the recovery folder and the update.zip on the sd card, I booted into recovery and the installation bar came up like it was installing, then switched back to the stock recovery. I assumed all went well and rebooted the device then powered off again and tried to boot into CWM, shows the three birds and the recovery key detected but doesnt go any further. I can power the device off and boot it back up into the stock rom but every time I try to boot into recovery, it does the same thing and gets stuck. Any help would be great.
CWM v8 isn't compatible with 1.2 branch.
My website here.
Hello guys,
as a last resort I turn to you for help. Have been searching for the answer for the last 2 days. I am running CWM-based Recovery v.6.0.1.1 and have a rooted x10 together with an unlocked bootloader. I flashed the recovery without any problems and installed miui v4 but an older file which was very unstable (without any problems). Then I decided to install the newer version so i downloaded it, placed it on my sdcard and in the same recovery flashed rom. Unfortunately I had my usb cable plugged in all the time (during installation). Installation got stuck in the middle and nothing could be done so i removed the battery and started the phone again (this time without the usb cable). When I tried to reinstall that rom again it gave me status 7 error installation aborted, assert failed:getprop,error in sdcard and things like that. So I tried the ROM which had already worked on my phone but received exactly the same message. What is more usb storage mounting in the recovery doesnt work anymore (but it already worked!). Now the problem is that I don't have any system installed and when i try to flash the recovery again, flashtool does not recognize my phone (so does windows) and so it leads me nowhere. I think this is definitely problem with the recovery, after the failed attempt to install rom when i had to remove the battery it does not behave normally. Is there any way that I can maybe install another recovery from .zip - i do not even know whether it will install or just sends me another error. Any help would be greatly appreciated
SqU33z3R said:
Hello guys,
as a last resort I turn to you for help. Have been searching for the answer for the last 2 days. I am running CWM-based Recovery v.6.0.1.1 and have a rooted x10 together with an unlocked bootloader. I flashed the recovery without any problems and installed miui v4 but an older file which was very unstable (without any problems). Then I decided to install the newer version so i downloaded it, placed it on my sdcard and in the same recovery flashed rom. Unfortunately I had my usb cable plugged in all the time (during installation). Installation got stuck in the middle and nothing could be done so i removed the battery and started the phone again (this time without the usb cable). When I tried to reinstall that rom again it gave me status 7 error installation aborted, assert failed:getprop,error in sdcard and things like that. So I tried the ROM which had already worked on my phone but received exactly the same message. What is more usb storage mounting in the recovery doesnt work anymore (but it already worked!). Now the problem is that I don't have any system installed and when i try to flash the recovery again, flashtool does not recognize my phone (so does windows) and so it leads me nowhere. I think this is definitely problem with the recovery, after the failed attempt to install rom when i had to remove the battery it does not behave normally. Is there any way that I can maybe install another recovery from .zip - i do not even know whether it will install or just sends me another error. Any help would be greatly appreciated
Click to expand...
Click to collapse
Flash tool recognize your phone? if yes flash any stock firmware and start over
quintas84 said:
Flash tool recognize your phone? if yes flash any stock firmware and start over
Click to expand...
Click to collapse
When I want to flash .tft file and i go to flash mode it does not recognize my phone in windows even though I have installed all the necessary drivers. It starts to flash but then says flashing aborted (this did not happen before, i could flash without any problems). Another problem is that i do not have any rom installed right now so i cannot even switch debugging on and if i remember right, i left debugging off in my previous rom.
Use Sony Update Service. Download from Sony site and install on PC. Follow the instruction, and this will reflash Stock Rom and Kernel (GB 2.3.3). Then, with latest Flashtool, first Root phone again, then flash whatever you want (custom kernels, roms..). You don't need to unlock bootloader again. It remains unlocked.
Sent from my X10i using xda premium
Dzufa said:
Use Sony Update Service. Download from Sony site and install on PC. Follow the instruction, and this will reflash Stock Rom and Kernel (GB 2.3.3). Then, with latest Flashtool, first Root phone again, then flash whatever you want (custom kernels, roms..). You don't need to unlock bootloader again. It remains unlocked.
Sent from my X10i using xda premium
Click to expand...
Click to collapse
Omg - I found solution to my problem - I just changed usb port and it started to flash even using flashtool. Still, many thanks since it helped me find solution
Hi, few month ago, I have unlocked the bootloader, rooted my phone, and installed CWM and CM 11.
It was quite buggy, and OTA updates didn't work, and I needed something more stable.
Yesterday, I wanted to reboot into recovery, and try flashing SlimKat or a newer CM if I don't like the Slimkat.
The combination of keys for Recovery didn't work and there wasn't any reasonable way to get around it.
On adb, the phone got detected, but offline, so I wasn't able to reboot into recovery this way.
Fast forward couple of hours, I have tried flashing about everything, but didn't manage anything besides being able to pass adb commands.
Now,
- when I turn on the phone the phone hangs on the Sony logo and I have to force turn it off
- I get the phone on ADB even when it keeps hanging on the Sony logo
- I can get into Fastboot by holding the up button on conneting to computer
- I have flashed the boot.img from CM11 for XPeria P to bring CWM back, but didn't happen, or did happen, but I can't get into recovery
- "adb reboot recovery" brings me to the same old hanging SONY logo.
- pushing whatever on boot doesn't help > SONY logo
Please help!
Why not just flash stock with flashtool?
[SOLVED] Partially...
I have downloaded FTF file for the device, and manage to flash it using Flashtool (worked only if I flashed incl. Kernel) and got the device up and running. I tried reflashing CM and Slim again, but none worked as I still wasn't able to get into recovery, so I reflashed once more. Finally, the device is working - with the stock firmware, at least...
davidszedely said:
worked only if I flashed incl. Kernel
Click to expand...
Click to collapse
This is a solution. When you flashing CM you need to flash CM kernel too. In some cases kernel needs to be flashed several times(for example before flashing CM and after flashing it).
Sorry for my bad English.
Thanks a lot for explanation. I'm happy to have the stock now, and will probably stick with it for the time being.
Hello, i will try to be thorough.
BUT, i am a noob and didnt write down everything i did.
Have a I717 at&t note 1. with the 4.1.2 update originally OTA installed by keis.
I recently rooted it using Saferoot. it went well and i didnt see any problems. i flashed a custom rom and didnt like it so using clockworkmod recovery i went back to the 4.1.2. I then tried pac lollipop >pac_quicyatt_lp.beta-1.unofficial_20150327< i liked this rom but needed to flash Gapps.
This is where the trouble started. i didnt/dont know the proper procedure to flash the Gapps on top of or into the rom.
I first tried >gapps-5.0.x-20150404-minimal-edition-signed.zip< and it looked like it loaded correctly. but nothing appeared in the phone. the pac rom was still working well.
I then did more research and tried >gapps-lp-20150222-signed.zip< , again it looked like it loaded well but nothing showed up "in" the phone.
right here is where things got screwy. i had been using clorkworkmod for recovery and rebooting. and i think somewhere in developer settings i clicked something about how rebooting is handled.
because after trying to install the Gapps it went into Cyanogen recovery... and loops.
no matter what i do it goes back to cyanogen recovery.
I never knowingly installed cyanogen and dont know why it all of a sudden is going into cyanogen recovery over and over.
a list of things that may have bearing:
1. i tried reinstalling the pac rom. it loads and completes but it still just goes to recovery.
2. tried different ways of clearing cache and data wipes.
3. computer, kies, and odin 3.09 do not recognize phone.
4. have proper drivers on computer. phone was previously recognized by kies and cpu (4.1.2).
5. currently the only way to get anything into phone is by pulling sd card and reinstalling with info on it then using cyanogen recovery.
6. i have searched for about 11 hours and tried a bunch of things. but just restarts in cyanogen recovery
7. i was scared to fully try things i found that wernt specifically for the i717.
8. i could not find an original gingerbread rom. they all seemed fishy (needed downloaders. or ended in .zip.rar)
9. had backed up with clockworkmod and with titanium recovery (while in 4.1.2).
I dont know if i can reach the clockworkmod save through cyanogen recovery.... if so it seems like a great option.
10. at the bottom of the screen while loading rom is.... ---->>> E: cannot load volume /misc
11. only pac rom will successfully re-flash (even though it still just goes back to cyanogen). any other flash and it crashes halfway through.... i then restart and it just loops back to cyanogen recovery.
I searched here and tried the five recommended posts.
I could not try a lot of the "fixes" because the phone isnt recognized by cpu or odin (computer does beep when connected but doesnt show up anywhere).
Can you help me get back my phone please?
Randall
added
This is the only site i am asking for help on. I am willing to reply quickly and put in the time!
Thank you very much for reading this far.
Randall
It seems a bit trendy to mess with the recovery, resulting in a brick or bootloop.
Just making a new thread cause my case is a bit different.
I was on Existenz 4.7.0 when I decided to flash 5.0.
Wasn't a clean install, resulted in some app fc'ing and restarting, so i went back to trwp and used my backup, keeping in mind to come back and make a clean install when I can take the time it needs.
Made a few backups today and wanted to start the trwp backup when I realised that I wasn't able to enter recovery.
Installed the trwp app, which wasn't able to reflash the recovery.
So I read another posting and I decided to delete the chargemon and rename the chargemon.stock, but that wasn't that smart, I decided later.
So back home I downloaded the dual recovery software from NUT's website to totally reinstall the recovery. After some ADB trouble I managed to get everything running, the batch file installed the recovery, everything looked pretty, at the end of the process the Z2 rebootet and e voila, I'm stuck in bootloop, clueless.
When I power the phone you can feel the first small vibration, then the Sony logo appears, stays, and it reboots.
Reset Button, powering on and holding Volume up isn't doing anything, so is Volume down.
What can I Do?
I know I made a few mistakes, but help is still needed!
Bro, Please read carefully before installing recoveries.
Nut's Recovery is NOT for Marshmallow. and it will cause bootloop and same problem you encounter here.
Only Solution is to flash via flashtool and re-root.(personally i would flash a kitkat .ftf then root it with any of the available methods. you can try kingroot it is the easiest) after that install Nut's recovery and flash your MM rom which will come with its own working recovery.
Oh, ok, so thats the cause. Didn't know that, shame on me.
So Existenz 5 messed up my recovery and maybe the silly try of reflashing killed it totally or just the bootloader.
So I will try to setup a Win7 PC and setup flash tool properly (didn't seem to work on win10)
Thanks for that finger point I the right direction
Flashtool works on windows 10 no problem for me.
Just install the right drivers and install 0.9.18.6 version of flashtool and try different drivers it shall work
Will do, thanks a lot. Seems to me that I had a 4.7 Existenz Rom with bootloader/recovery from MM, which I destroyed.
Is it possible to reflash the old bootloader? Or will flash tool spare my datas on internal SD card?
why to flash a boot loader?? is your device unlocked bootloader??
It's locked.
So it can't be a broken bootloader?
So it's just because the recovery is messed up?
JackDCalloway said:
It's locked.
So it can't be a broken bootloader?
So it's just because the recovery is messed up?
Click to expand...
Click to collapse
yes bro don't worry.
It seems that you are new to sony or you re coming from samsung or any other device with recovery partition.
By default, Sony doesn't have a recovery partition like in samsung. that is why developers made the recovery a part of the system (your ROM) the chargemon files are the one responsible for the recovery. so when you install a recovery it is like you are installing a system application which can be messed up if it is not compatible with your rom version.
PS:Be carefull never wipe the system partition from recovery and restart your phone before installing a new rom because if you restart without having installed your rom your phone won't have a recovery(part of the rom) neither a system----> Bootloop and need to reflash.
you can unlock your bootloader and make a recovery partition and install aosp roms. but on sony once you unlock your bootloader you will loose a lots of features and camera enhancements. so better keep it Locked and use stock based roms like existenz and MIUI roms which are stock based.
I hope i have been able to clarify all
OK, makes sense.
Seems like I'm still pretty new to Sony. Came from Samsung last December, just got enough knowledge to flash and improvise, quick and dirty.
So if I could get hands on my old chargemon file, (from when I didn't tried to install Existenz 5) I may get the Z2 running again?
Of course a pretty clean install afterwards.
Just asking, cause of backup reasons
Edit: I knew that unlocking the BL has a few disadvantages. I'm happy with Existenz but now I know a few things more, thanks michel090428
it is very difficult now even if you have the chargemon file. i don't know what could be messed up with the system. go for a clean flash it is the most safe way to do it.
Read this guide if you want a help with flashing it is very easy and detailed. and remember it is better to flash kitkat .ftf as it is easily rootable.
http://www.gizmobolt.com/2015/04/09...z3-23-1-a-0-690-ftf-using-flashtool-manually/
Hey folks, I'm back again!
Managed to setup a Win7 PC, installed the correct drivers, setup Flashtool, found correct ftf file and so on.
Problem is that I'm only able to get into fastboot mode with my Z2, for me it seems like Flashtool won't work when the device is only in fastboot mode.
What can I do?
why you can't start your device with flashmode?
You need to shutdown the device then when flashtool ask you to start in flash mode you press volume down(keep pressed then you plug in USB cable and it should start in flash mode directly.
have you tried to follow the guide i posted in the first page? where are you stuck? which step?
michel090428 said:
why you can't start your device with flashmode?
You need to shutdown the device then when flashtool ask you to start in flash mode you press volume down(keep pressed then you plug in USB cable and it should start in flash mode directly.
have you tried to follow the guide i posted in the first page? where are you stuck? which step?
Click to expand...
Click to collapse
Was a bit tricky, did the 'vol down + plug in' thing several times and it worked suddenly, flashtool flashed the ftf. Now it's FCing several tasks while it would do the android setup. Trying to flash a 4.4.2 ROM now, thanks for patience and help, appreciated this!
WIPE DATA
JackDCalloway said:
Was a bit tricky, did the 'vol down + plug in' thing several times and it worked suddenly, flashtool flashed the ftf. Now it's FCing several tasks while it would do the android setup. Trying to flash a 4.4.2 ROM now, thanks for patience and help, appreciated this!
Click to expand...
Click to collapse
You re Welcome Bro,
Concerning the FC You need to check the WIPE DATA option in flashtool i think it will solve the FC's
I'm with 23.1.A.1.28 now and it's fine. Just need to get root, there should be an exploit but it's not working for me, reasons unknown. Going to have a look at it later. Want to flash Existenz, that's the goal.
Bro , Use KINGROOT it is able to root .28 firmware.
there is a thread here for kingroot.