I've taken the update while on boost mobile with note 3 and now no signal. I can go back to nc5 but i wanted the update. Anyone have a fix?
Ive tried mj4 modem and didnt work
Related
Ok im new to this site but not to new to root and flashing. Ok so here is what I have done. I rooted my S4 when i got it and everything was fine. Then when the 4.2.2 came out I updated it straight from my rooted s4. After so my 4G LTE for some reason has been cut in half. I always get a speed of 20 to 35 mb download at my house but after update I can only get up to 10mb. I tried last night to flash back to previous build or firmware but did not have any luck. So I flashed to stock firmware that the update came with (ME7) and then rooted it again but I still cant get speeds over 10 or 11 mb. I have another LTE phone side by side and the other gets over 20mb. Is there anything like flashing modem or anything else I can do to get my S4 to preform as it did before the update.
im using the sprint note 3 on pageplus and everything was good on mj4 then i updated to nab. well now I have no signal at all. im using kitkat killer rom. Found out that I need to roll back to the mj4 modem but I dont think it is working. everytime I flash a prl in dfs it says it sticks but on the phone under prl it just says 1.also after flashing the mj4 modem should my baseband also say mj4? **** me running!! after 4 hours of troubleshooting I odin back to stock and flash the mj4 modem. would not work when i was rooted and on a custom rom but once i went back to full stock and no root the I was able to flash the mj4 baseband and flash a different prl
johntheman_692003 said:
im using the sprint note 3 on pageplus and everything was good on mj4 then i updated to nab. well now I have no signal at all. im using kitkat killer rom. Found out that I need to roll back to the mj4 modem but I dont think it is working. everytime I flash a prl in dfs it says it sticks but on the phone under prl it just says 1.also after flashing the mj4 modem should my baseband also say mj4? **** me running!! after 4 hours of troubleshooting I odin back to stock and flash the mj4 modem. would not work when i was rooted and on a custom rom.
Click to expand...
Click to collapse
Long shot, but you might try Viperboy's PRL Helper from the Play Store: https://play.google.com/store/apps/details?id=com.viper.prlhelperfree
Works flawlessly for me, although I don't have cause to use as much as I used to.
So ive run out of ideas on this problem. I no longer can update my prl and profile. I was on freeza's not3 2.2/2.25b rom had some issues with slow data and other hiccups. Flashed stock debloated and got tired of its blandness so i moved back to freeza's hoping for a better experience now that it had some time. After flashing back to it ive run into these issues.
Poor network signal, unable to update prl or profile with error code 6602. Ive gone stock tar nh7 and reflashed the modem too with no solution. Ive regained network connection after losing it entirely for a bit but still cant update prl or profile. Everybody else is talking how theirs is working great....i havent done anything different. Hope to get some input. Thx ahead of time.
Reminder at this point everything is stock flashed on odin. Twrp recovery latest version. Odin 3.09
Jataadroid said:
So ive run out of ideas on this problem. I no longer can update my prl and profile...
Click to expand...
Click to collapse
I had similar PRL/Profile problems, 'tho I was getting error code 6500. Network connections remained strong and through-speeds were very good. But the failure to update Prl/Profile really pissed me off. I also tried return to stock, other ROMs, but same error 6500. I just lived with it and did the occasional battery pull to good effect.
Then I installed Sacs_Note4 _Ported_apps_Rom_V2.
As part of the installation instructions, I updated PRL & Profile and was shocked when they worked!
Then I set up the phone as I like it, and back to error code 6500.
I turned-off the various Wanam mods and presto, no 6500 error code.
I then added them one at a time, (stuck with a few less this time) and still no error code 6500.
Good luck!
I ran into issues trying to upgrade the ROM on my gf's phone, so for now I reflashed to NK1 using Odin (full wipe/re-partition).
Phone is just barely connecting to the network after the reflash. (Shows signal strength around >20 dBm below what it used to be). Chatted w/ VZW support and the rep did all he could to reset on their end, pushed latest PRL.
What could I be missing?
You could try a different modem. Also flash the correct modules after any rom or modem flashing.
http://forum.xda-developers.com/showthread.php?t=2487298
[MODEM][Zip] Modems for Loki'd & Safestrap roms (12/03/2014)
Sent from my SCH-I545 using Tapatalk 2
So, I am on the nightly CM12.1 build for the hltespr Note 3 (N900P). This is the one.
I can't seem to find anyone else experiencing this exact issue and it hasn't been posted recently. I have no 4G/LTE service. I have toggled every setting both in the regular settings and under the *#*#4636#*#* settings and nothing seems to work. I was able to flash a stock rom and got LTE service immediately but again got nothing but 3G when I flashed CM12.1 back.
Any suggestions would be greatly appreciated.
Edit: Just wiped data, delvik, cache, etc and loaded the latest nightly fresh and I still get no LTE.
Same here i only get 3g on any room i tink it is something wrong with our modem im using the last kernel h1 let me know if u found the answer
Same here. I flashed Phronesis N5 v6.5 (with the CSC set to SPR and updated my apns-config.xml to a copy from my wife's identical phone) and have only been able to get 3G. I have reverted back to stock and 4G was up and running. This is my headache right now. We need to pull our heads together and get this figured out. My baseband is OK2 right now. I was thinking maybe upgrading to the PH1 would help. It's just odd it works fine with stock.
I just realized wilder90 said he has PH1 running and it's not working. Maybe I will still try it.
*Update- I rolled back to stock and upgraded firmware to PH1. My build says LRX21V.N900PVPUEPH1 but baseband and software still say N900PVPUEOK2. I have 4G working. Do I have to update baseband/software another way?
*Update- I downloaded PH1 from sammobile.com and flashed the update through Odin. Now all says PH1. 4G still working great. I am going to flash Phronesis again and see if there is a change.
*Update- I changed my mind and went with "Sprint Users Rejoice!! MM 6.0.1 Darklord Modded V5 By JCordero31 N5N7 APPS 1/22/17"
I have 4G/LTE working. It doesn't have really any customization available but it works and it's new.