I noticed there are dust in the front of my phone, you know, where the screen joins the sides bezel. While I may be anal, but I worry about dust getting in under the screen as have happened on my previous mobile phones.
Is that likely to happen to the SGS2? ie dust under screen.
Is there an skin that will go over the joining cracks to stop more dust getting inthere?
Yes there is dust between screen and the surrounding plastic, because of the small gap. But no dust under my screen yet.
I think Samsung took care of it.
you will hardly be able to get any dust under the screen since glass and the screen are one. so its kinda impossible
Agreed with the above comment. The Digitizer (Touchscreen) and the Display is joint together and it is not possible to separate them, hence there is no chance of dust getting accumulated between the Display and the Touchscreen.
Same with the Galaxy S
well, it seems that its not so impossible afterall...
I just can't believe me eyes just woke up this morning and reached for my phone, after a small wipe of the screen i saw one little spot that wasn't coming off... after a closer look i realized that the little spot of dust is sitting comfortably under my screen
this is a real bummer for me, never had a similar issue on my previous phone, does anyone know a real solution for this issue?
will try to take a picture and post it later
no dust for me
jeanclaudevandamme said:
I noticed there are dust in the front of my phone, you know, where the screen joins the sides bezel. While I may be anal, but I worry about dust getting in under the screen as have happened on my previous mobile phones.
Is that likely to happen to the SGS2? ie dust under screen.
Is there an skin that will go over the joining cracks to stop more dust getting inthere?
Click to expand...
Click to collapse
Did you manage to remove the dust or did it get stuck like that?
Any ideas on the best/cheapest way on replacing the glass on my Vibrant (sgh-t959)? My screen broke down towards the bottom end of it and put 3 cracks running all the way up the face. I can still see my screen fine and the touchscreen still works, although super senitive around the point of impact, so i'm pretty sure all i need is the new gorilla glass. Any help is greatly appreciated/needed.
I recently changed the screen on my note 2. When I put the new glass on i noticed it looked like a water mark when I pressed on the screen. The top half works fine when I touch it and the entire screen works fine with the s pen. would the LCD glue fix the problem?
I'm pretty certain it would. You need adhesive between the digitizer/lcd combo and the glass screen. That's how it is stock.
I hope so.
My friend gave me a note 2 and it has a cracked screen. I was wondering if i should replace the screen+digitizer or just the digi. The lcd still works and so does the digitizer but a cracked screen just annoys me.
lolwutwin said:
My friend gave me a note 2 and it has a cracked screen. I was wondering if i should replace the screen+digitizer or just the digi. The lcd still works and so does the digitizer but a cracked screen just annoys me.
Click to expand...
Click to collapse
yes the glass alone is I'm thinking around 30 us dollars on the web the glass is glued together to the amoled lcd touch panel and can be removed with the following tools .....hair dryer highest heat setting, plastic tweezers, I actually took the whole phone apart to avoid heat damage to the internal components. apply heat to the whole screen from the outside only. caution very hot so wear gloves now slowly and I repeat very gently with tons of patience start prying off piece by piece then clean and losen the glue with alcohol then I used a stain remover I cant think now but will get back to you on that good luck
I've got a Galaxy S III (i9300) with a very shattered front glass. The display and digitizer works just fine though. Menu, back and home buttons too. Everything is working, i just need to replace the front glass. I've once replaced the whole front package (LCD, Glass, Digitizer) on a Galaxy S2 very successfully so i have some form of experience.
Will be my first time replacing only the front glass. Unfortunately i wont be able to put any LOCA there as i dont have any UV light. I do however some regular adhesive 2mm tape that i will put around the screen to prevent dust and stuff from coming in. Also i dont have a IR thermometer and i will be using a hair dryer. I know how hot it has to be by feeling it. I should almost not be able to hold my hands on the glass. It might take a very long time but if its possible to do it, im willing to try.
What i'm worried about is the glass shards that are in the middle of the screen. Most shards end at the edge of the screen so i can apply pressure there when im removing the shards. But the shards in the middle have all edges on the digitizer. I cannot apply any form of pressure towards the digitizer so im worried of how ill remove them. Also the left lower corner around the menu button is full with tiny shards. like 0.5mm-3mm shards. Im wondering what is the best way of removing them? BTW i still got the touch screen protection plastic on. It got bubbles now cuz of the cracks.
Here is a picture of how cracked it is. Its not exact but close enough. Paint is OP.
The black spot in bottom is where the glass is simply gone. It fell of after time. I put some tape over it to cover it up so nothing can fall in.
Any advice on how to remove these shards?
Very appreciated