I flashed custom recovery image successfully and after that, when phone has to restart, it just stuck at LG logo.
When I tried to enter in custom recovery menu, but it shows only LG logo.
I tried to connect with PC, but it was unsuccessfully. The PC doesn't recognize the device. (nothing happens).
Can anyone help me?
This happened to me also. I solved it like this:
First thing to do is get sure the LG drivers are installed ( there is a topic in the forum on this also).
Install KDZ ( serch in the forum and download it)
Download a room ( stock or not )
Flash the phone with KDZ ( after the drivers have been installed the phone should be detected on the pc.
After flashing if it does not start up do not fear, get the battery out, re install the battery and do a hard reset power+home+volume down buttons pressed at the same time and it should work.
If its your first time install Stock GB 20E as it is an open room, if not new to this I would suggest CM7.
Hope it helped
Regards
But the PC doesn't recognize the phone.
Here is the log from KDZ:
[R&D Test Tools Log File]
23:47:37 : Launching SW update
23:47:37 : Unpacking KDZ
23:47:39 : KDZ file extraced
23:47:40 : Files were extracted.
23:47:40 : LGMobileDL Load.
23:47:40 : Port = -1
23:47:40 : Connecting to phone
23:47:40 : PHONE WAS NOT FOUND!
23:47:42 : ===FINISHED===
Click to expand...
Click to collapse
How should I solve this problem? :/
bondzi said:
But the PC doesn't recognize the phone.
Here is the log from KDZ:
How should I solve this problem? :/
Click to expand...
Click to collapse
I had this same issue too, do not worry.
Keep your phone plugged into your computer, and go to Start > Control Panel > System > Hardware > Device Manager > Modems and disable the LG modem.
I am on Windows XP, so it may not be the same steps, but the point is that you have to disable the LG modem in Device Manager.
I had the same problem as well at one point. What operating system are you running on your computer?
I had the same issue, but I could not find the LG modem to disable it, it was just that windows was not detecting my phone at all, or using the drivers I had installed for my P500 to figure out what was connected to my laptop. Bricked phone after a failed ROM flash. Reinstallation of USB drivers for my phone failed to do anything.
Have you used LG Mobile update at all? I got all my drivers through it, rather than useless PC Suite 4.
Download it through HERE
Here's what I did to rectify it (Running windows vista):
DO NOT PLUG IN YOUR PHONE UNTIL STEP 3!
1. Went to system restore in windows(you'll find it under Backup and Restore in the Control Panel) and restore your computer to a state before installing any drivers for your phone.
2. After everything had completed, installed LG Mobile update. There is an option to install general USB drivers for your phone, DO NOT do it! Go to Customer Support > Application, Manual & USB driver download. Input your IMEI number from behind the battery in the back of your phone(or just select the "Read your phone" option if you can get it to read your phone). It will search and return the correct drivers for your exact phone. Download and install your USB drivers.
3. Keep your phone disconnected from your PC, and start up LG mobile update again. Connect your phone, LG mobile update should verify the connection by trying to connect to your phone, checking software versions, etc. It will connect even if you are stuck at the LG screen.
4. If everything checks out run KDZ updater and flash your phone back to original specs.
hey first go to emergency mode by pressing back(return) and volume up
and then in emergency mode use kdz it then only pc will recongnise your phone
believe me this thing also happens with me and I know that time I very scared
that time I used this article
http://forum.xda-developers.com/showthread.php?t=1015332
bondzi said:
I flashed custom recovery image successfully and after that, when phone has to restart, it just stuck at LG logo.
When I tried to enter in custom recovery menu, but it shows only LG logo.
I tried to connect with PC, but it was unsuccessfully. The PC doesn't recognize the device. (nothing happens).
Can anyone help me?
Click to expand...
Click to collapse
read general thread it has been answered many times,stucking at lg logo is solved by take out battery reinsert and the 3 button combo
have u tried HOME + VOL DOWN +POWER BUTTON,still if it dont,
read downgrading details here http://forum.xda-developers.com/showthread.php?t=1038338
error guide here http://forum.xda-developers.com/showthread.php?t=883314
The same problem. But i solved it.
1) install again the driver using B2CAppSetup
2)This is based by xda forum by: Zecanills with a detailed explanation from my side.
- You need to download the firmware of your device. Download "Orginal LG Firmware" application (search in xda forum). Open it, put your IMEI and you will download the original ROM.
- Download KDZ updater and uncompress it
KDZ_FW_UPD_EN.zip - 4shared.com - online file sharing and storage - download
- Install msxml.msi from the uncompressed directory
3) Remove the battery, put it back and start the phone in emergency mode (actually the only way possible) back+up volume+power
Connect your device and run KDZ_FW_UPD.exe (as administrator). If the phone is not recognized repeat step 3) several times.
Select Type : 3GQCT
Select PhoneMode : DIAG
In KDZ file : Choose the ROM file you downloaded in the step 2)
Press Launch software update and wait (It will be 10 minutes or so).
Wait until it reboots.
After reboot will appear an image as in the following link: http://androidforums.com/getitnowmarketing/330813-all-one-recovery-thread.html
Don't worry. Restart phone again pushing power button (or remove battery, put it back and push power ) and then after few minutes you will have the phone as the begging when you bought it.
Thanks people for helping me. I just put the phone in emergency mode (Volume UP button + Home button), connected to the PC and flashed with KDZ.
After that, the phone works fine.
Thank you again!
bondzi said:
I flashed custom recovery image successfully and after that, when phone has to restart, it just stuck at LG logo.
When I tried to enter in custom recovery menu, but it shows only LG logo.
I tried to connect with PC, but it was unsuccessfully. The PC doesn't recognize the device. (nothing happens).
Can anyone help me?
Click to expand...
Click to collapse
man i am new as this thing
my lg is p925 and i didnot know that after i install root kdz for p920 and when i run rom maneger i did not find my model lg p925 so i tryed the res of the lest in rom maneger
bad move..........one of them is about lisen or somthing like that....but when i restart my phone frezzzz in lg logo ...i went to recovery mode (vol dwn+power)and all list about wiping no install zip in sd so i tryd (vol up+connect to pc) works so i use lg update an it says i have last apdate then i tryd cs>recovery with imei number but it says model not spport s/w....what must i do..dose flash it will hilp me? plzzzzzzzzzzzzz hilppppppppppp
LG P925
Same thing happened to me! I'm desperate... I've done research for hours and tried everything but no success so far... anyone could help us?
88prince said:
man i am new as this thing
my lg is p925 and i didnot know that after i install root kdz for p920 and when i run rom maneger i did not find my model lg p925 so i tryed the res of the lest in rom maneger
bad move..........one of them is about lisen or somthing like that....but when i restart my phone frezzzz in lg logo ...i went to recovery mode (vol dwn+power)and all list about wiping no install zip in sd so i tryd (vol up+connect to pc) works so i use lg update an it says i have last apdate then i tryd cs>recovery with imei number but it says model not spport s/w....what must i do..dose flash it will hilp me? plzzzzzzzzzzzzz hilppppppppppp
Click to expand...
Click to collapse
Hi!
I had a problem yesterday with my Amoi N828 cell phone. During a contact list or messages searching, my phone was automaticly restarted. My idea was to make a system restore using option available on the power on/off button. After that I saw chinesse menu which is not understoded for me I pressed some button and after that such process was started and stopped during 15 min. My decision was to a phone restart. And right now, during system initialization I'm seeing only Amoi logo and phone is stoped.
My next step was to flash system again. I found some drivers MT6589, additionally firmware and "SP flash tool"
When I'm connecting phone without battery by USB cable to the system (Win7 32 and 64 bit) is detected and looking the drivers. And now is a problem. my device is visible for the moment and after that is disappears and again - see link below:
youtube.com/watch?v=Wg47gdlB7YU
the question is why? When the drivers are installed, the problem is still same like before - nothing changed
PLEASE HELP ME! I'm woeful ((((
Hello,
During the past days I've been trying to flash my C7 with no success. When pressing power button, it turns on and displays the Alcatel logo but stays there, it does not load the OS.
I have tried to use SPtools to flash it, I have the mtk drivers installed in my PC. When I plug the switched-off phone to the computer it turns on and couple seconds after my PC detects it (I can see the preloader mtk loaded on the device manager); however, one second right after it is detected, it is disconnected as it keeps booting to show the logo and stay there. Obviously, if the phone is not detected I cannot use SPtools to flash it.
Any suggestion will be highly appreciated.
PS: I have also tried to connect to it with adb, and dump a ROM using sideload with no sucess, the PC recognizes it from the recovery but after copying the image nothing new happens on reboot.
Hi guys, I recently purchased a Homtom HT3 for my mother, when it arrived to me I charged it and checked it out a bit just to make sure everything was fine which it was.
She collected it from me the next day and told me she'd start to use it the day after, she calls me up the next day and tells me there's some problems with it and a few people at her workplace tried to fix it for her to no avail. I pick the phone back up and I notice that everytime I power it on, it gets stuck on the "homtom" logo.
As I don't know too much about fixing phones I only took the following steps before asking for advice here; I went into recovery mode by holding up volume and power button, the android guy with the red triangle appeared so I tapped up + power button to get into the recovery(?) menu. I wiped the phone to factory settings and deleted the cache in there but it hasn't fixed the problem.
I assume I need to flash a firmware or something to potentially fix this, but I'm unable to find an official firmware from doogee/homtom's site for the HT3. I've found a firmware that I downloaded from "chinagadgetsreviews" but I'm a bit weary to try and flash with that rom because it isn't from the manufacturer. (even if I knew how to - the only experience I have is rooting my own phone but that's when I actually had access to a working phone, not one thats stuck on a boot logo).
Sorry for the long post but could anyone guide me in the right direction here? TIA
I'm not opposed to not using official firmware, I think I use cyanogen mod(?) on my own phone. I'd just like the problem fixed in the easiest way possible.
Trying to fix it myself by flashing a rom via SP flash tools but I've ran into another problem which is stopping any kind of progress - the phone isn't detected in Windows, I can't enable usb debugging because I can't get passed the boot loop, I've tried installing the ADB driver manually which didn't seem to work (just said it didn't install correctly and left me with a yellow exclamation mark) and I tried to install it automatically via ADB driver installer but it just throws up an error that the device isn't detected.
Any help would be greatly appreciated.
Hello. I bought a Homtom HT3 and next day a done an update with sp flash tool. all gone ok, but phone now wont to turn on. I contact homtom and got all drivers and room to fix it. Now i have a problem , i hit download on flash tool , take off battery + pres volume down + conect phone on usb cable. My computer detect it as USB MTK PORT sp flash tool load only the first red line but not detecting phone info, then after 1 minute i get
s_ft_da_no_response(4001) da didn't send response data to flash tool.
I changed drivers port even to MTK preloader, but i get same error.
NOTE....... All drivers and rom i got original from HOMTOM.
Thanks to all who can help me.
I can show a screenshot if need.
Same here - any solution for this problem?
Kleos89 said:
Hello. I bought a Homtom HT3 and next day a done an update with sp flash tool. all gone ok, but phone now wont to turn on. I contact homtom and got all drivers and room to fix it. Now i have a problem , i hit download on flash tool , take off battery + pres volume down + conect phone on usb cable. My computer detect it as USB MTK PORT sp flash tool load only the first red line but not detecting phone info, then after 1 minute i get
s_ft_da_no_response(4001) da didn't send response data to flash tool.
I changed drivers port even to MTK preloader, but i get same error.
NOTE....... All drivers and rom i got original from HOMTOM.
Thanks to all who can help me.
I can show a screenshot if need.
Click to expand...
Click to collapse
Hi Guys,
I'm in a bit of a problem. I bricked my phone and nothing seem to help.
Let me tell whats happened
1. I updated my TWRP in LeTV X500
2. This kinda made my phone to in soft brick mode every time I restarted it went to TWRP
3. I than installed new ROM from TWRP (i think it might be too high for my phone)
4. Phone endup bricked, not switching on, off nothing - redl light only
5. I tried here to install new rom from Windows and Linux via SP Flash Tools - phone is not recognised.
6. I disassembled the phone and detached battery
- now this is actually helped in a way that windows now recognises the phone, but the connection is not continous
- it recognises MediaTek Pre launcher ... few seconds pass
- it disconnets the MT Pre Launcher
- It recognises VCOM USB Port ... few seconds pass
- It disconnets again
- loop like this goes on and on
7. I tried holding any of the buttons (up, down, power and combination) - not helping
8. I believe my last option is to try and bridge some of the points on the motherboard to try and reset the system ... is this correct?
I have no idea what should I bridge with what ... there are no labels on the MB, i'm not even sure where the GND is.
Any ideas fellas?
Here is front of the MB:
Code:
imgur.com/a/b4oWI
Here is back of MB
Code:
imgur.com/a/XgZiV
help will be appreciated
Have you found a solution?