Related
I made a very simple init.d script to make sure that my IVA UV on my Galaxy Nexus would go back to their values after reboot. However, when I tested the script through Script Manager it shows an exit code 1 on the "is executable" part, along with "No such file or directory". I have been looking around for about 2-3 hours trying to find a solution but to no luck. I have attached a screenshot of the boot log. Thanks.
Also if it helps any, the following is the script's contents:
Code:
#!/system/bin/sh
# IVA
echo "1050 950 900 825" > /sys/class/misc/customvoltage/iva_voltages
Update: I have found the solution, thanks for the help!
Want to save power when WiFi Tethering... try WiFi TXpower. You can find it here:
https://play.google.com/store/apps/details?id=rubberbibpepper.WiFiTxPower
Solution for missing IWCONFIG file:
1. Download the first attachment "iwconfig.txt" (default save location is '/mnt/sdcard/download')
3. Open 'File Manager'
a. Select: 'Menu' -> 'More' -> 'Settings' -> scroll down paste 'donate' (which you should do!)
b. Select: Mark Yes for both checkbox options of "Root Explorer" & "Mount System Folders"
3. Navigate your path over to '/mnt/sdcard/download' and find & rename the file "iwconfig.txt" to 'iwconfig'
4. COPY the file, and navigate your path over to '/system/xbin' and PASTE the file. It may say it wasn't pasted, but scroll down and the file will be there.
5. Launch busybox 'terminal emulator' and type these two commands:
# su
# chmod 755 /system/xbin/iwconfig
6. Boot up WiFi TXpower and verify that the iwconfig error message is gone, and that you do not get a 'iwconfig' permissions error. You should see "iwconfig" and "eth0" titles and all the signal and power stats listed in the app. Lower numbers, less range, and greater batter life.
7. Enjoy! If this has helped you, please hit the "Thanks" button below.
Backstory:
Problem is, this app needs a file 'iwconfig' to be installed in '/system/xbin' and this directory is R/O (read-only, write protected). There are a few ways to do this;
adb push to install the file
Find an APP that will install iwconfig for you
Symlink the file if its somewhere else
Copy & Paste File yourself
I'm old school, so I like to have a hard copy of the file anywhere its needed, and at 30.4 KB, who cares. So following the 80% help link below, I downloaded the 'iwconfig.tar' file, extracted the internal file, and started trying to copy it into '/system/xbin'. From this same site, I used fragments of commands in the busybox 'terminal emulator' to finish the install after the file was copied into the directory. I used '# chmod 755' to set the permissions on the new file, so WiFi TXpower could use it.
"Quoted from:
# su
# cd /mnt/sdcard/download — (this assumes the download location of the file)
# tar –xf iwconfig.tar — (this was to extract the single file from inside the tar file)
# mount –o rw,remount /system — (I couldn't get this command to work, but you can try next line below instead)
# mount -o remount,rw -t yaffs2 /system /system — ccdreadcc line of code, that looks like it would work, I received no terminal emulator errors when attempting.
# cp iwconfig /system/xbin — (Above didn't work, so I copy & paste this file in 'File Manager' as I couldn't get 'Root Explorer' to do it, it wouldn't R/W '/system')
# chmod 755 /system/xbin/iwconfig — (You will need this later to correctly set permissions on 'iwconfig', if you don't you will get a "permission denied" error in the WiFi TXpower App)
"
Helpful Links:
80% Help to figure this out, and will be quoting useful parts to solution:
http://jhanford.wordpress.com/2011/10/03/lowering-wi-fi-transmit-power-in-android/
20% Starting and finishing information for solution:
http://forum.xda-developers.com/showthread.php?t=1209251
Attached Files
Does anyone have this working on ICS or on an HTC Glacier MT4G?
My rom has the file needed, but I could not get it to show any type of config, then I tried this method and still nothing.
RUN IT
Working on VZW GS3! Thanks buddy for the help! BEEN LOOKING EVERYWHERE!
---------- Post added at 01:34 PM ---------- Previous post was at 01:11 PM ----------
What does iwmulticall do exactly? Would it benefit Galaxy S3 Wi-Fi or battery?
deep thoughts
zwieringa said:
Working on VZW GS3! Thanks buddy for the help! BEEN LOOKING EVERYWHERE!
---------- Post added at 01:34 PM ---------- Previous post was at 01:11 PM ----------
What does iwmulticall do exactly? Would it benefit Galaxy S3 Wi-Fi or battery?
Click to expand...
Click to collapse
I am running on a rooted sprint samsung S3, the app continues to show::
iwconfig:
Unknown id: wlan0.
when I select 4dBm, there is no indication it worked. In terminal I run iwconfig, and it shows that the setting took effect! My stock power is 1496, which seems to be my max. Selecting 11dbm works, but 18, 25 and 32 do not. I am guessing my wifi adapter will not allow anything over 1496.
If I had iw and ifconfig on my device I could try this to force a higher speed:
ifconfig wlan0 down
iw reg set BO<--------------is an o not a 0
ifconfig wlan0 up
iwconfig wlan0 channel 13
iwconfig wlan0 txpower 30
any suggestions how to pull this off.. I can install this on a debian destro, but there's no point to that... if I can get the iw and ifconfig on my andriod OS, maybe I can force it higher than 1496...
Tried this.. Surprisingly, it's also working on my Nexus 7 (2012) too..
Not that is requires wireless extensions.
Code:
[email protected]:/data/data/bcmon/misc $ ./iwconfig
lo no wireless extensions.
svnet0 no wireless extensions.
ifb0 no wireless extensions.
ifb1 no wireless extensions.
sit0 no wireless extensions.
ip6tnl0 no wireless extensions.
wlan0 no wireless extensions.
In last Samsung Aries kernel, it's one of these:
Code:
CONFIG_WIRELESS=y
CONFIG_WIRELESS_EXT=y
CONFIG_WEXT_CORE=y
CONFIG_WEXT_PROC=y
CONFIG_WEXT_SPY=y
CONFIG_WEXT_PRIV=y
CONFIG_CFG80211_WEXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
iwconfig has no effect on tx-power
This is great, thank you.
Unfortunately, when I followed all the instructions, got the iwconfig file from this thread, renamed it, successfully put it into system/xbin/, and then ran "iwconfig wlan0 txpower 2dBm" and then "iwconfig wlan0" the tx-power level is unchanged. It is still listed as 19 dBm. There's no error message.
Any ideas?
Does the "iwconfig [interface] txpower" command need to be run in a certain manner for it to have effect?
(I'm running a nightly build of Cyanogenmod 11 on a Moto G 4G.)
Yes, it's works on SGS4 i9506 4.4.2 after install iwconfig/iwmulticall. The signal is really changing, I see it when checking with other devices.
"iwconfig" shows txpower=31dbm for wlan0 (on other devices - S3, S5 and Tab - it shows 1496dbm)
I send command "iwconfig wlan0 txpower %%" with different values, but only 4, 11, 18, 25 and 31 works (yes, the last is not 32).
How can i increase it for better signal?
sorry for my english!
Thanks
Also I tried this:
iwconfig wlan0 sens -90
but
SET failed on device wlan0 ; Operation not supported on transport endpoint.
Is it needs orher diriver for wifi?
it doesn't work on lollipop
any ideas how to make it work on lollipop
Same here. Any solutions for Lollipop iwconfig?
error: only position independent executables (PIE) are supported.
how to fix this problem?
---------- Post added at 11:06 AM ---------- Previous post was at 10:46 AM ----------
kotaries said:
error: only position independent executables (PIE) are supported.
how to fix this problem?
Click to expand...
Click to collapse
Answering my own question:
You see this error because android doesnt want you to run old binaries on new version of system (as google explains, if I got the idea correctly)
To rebuild the binaries for new system is pretty complicated, so you can just fool the system by changing 17th byte in current (not working) binary file
Open some hex editor (online version for example: hexed.it), find the 17th byte (counting from 1, as humans do) and change it from 02 to 03
This byte (as I now see) is the first byte on 2nd string in the hex editor
Good luck
Try to edit, but the result "Segmentation Fault" :3
Just starting to look into writing my own init.d (for use with perseus kernel for example.)
can any one point me in the right direction for a beginners guide to init.d?
I have searched but it is mainly linux in general that comes up - nothing specific to Android or the GSIII.
thanks
found this, which seems a very good start.
Beginner's Guide to init.d Scripts
init.d scripts has to be copied to /system/etc/init.d. All scripts in init.d are automatically executed after booting. (in Siyah, 30 seconds after booting)
I) How To:
1) In an editor such as notepad++, type #!/system/bin/sh
This should be the first line of all shell scripts. This invokes the compatible shell to execute our scripts.
2) From next line, type in your scripts line by line. After saving, push it to /system/etc/init.d using root explorer.
3) Use Script Manager from market to run the script as root to make sure there are no errors. (if you're confident of your script, then no need of script manager)
note: if you use editors such as wordpad to create a script, the carriage return leaves some 'invisible' illegal characters in the script and hence the script will fail to execute. So use editors such as notepad++, or use script manager itself to make the script.
4) If there are no errors when you run using script manager, then navigate to the script and set the following permissions:
owner: read,write
group: read
others: read
Also check 'set UID' and 'set GID'.
Now you're all good to go. Your script will be executed each time you reboot.
II) References:
We can use init.d scripts to perform a lot of things.
Refer post 2 from Q&A (courtesy kwerdenker)
http://forum.xda-developers.com/show....php?t=1325831
Use this post as a reference on how to tweak or change Cpu Frequencies/Voltages, Gpu Frequencies/Voltages, Bus Speed, I/O Scheduler, Charge Current, etc.
Apart from these, you can also tweak sched_mc values, change backlight response curve, change upper and lower thresholds for second-core-active (for screen-on and screen-off), etc.
III) Examples:
1) sched_mc
Ex:
echo "1" > /sys/devices/system/cpu/sched_mc_power_savings
This cause filling cpu0 (1st core) first for long running threads and processes.
Valid values are 0, 1 and 2
2) Second Core Active Threshold
Ex 1:
echo "70" > /sys/module/pm_hotplug/parameters/loadh
echo "25" > /sys/module/pm_hotplug/parameters/loadl
During screen on, This causes cpu1 to kick-in only after the load on cpu0 reaches 70% and cpu1 to turn off when load is less than or equal to 25%
Ex 2:
echo "90" > /sys/module/pm_hotplug/parameters/loadh_scroff
echo "35" > /sys/module/pm_hotplug/parameters/loadl_scroff
During screen off, This causes cpu1 to kick-in only after the load on cpu0 reaches 90% and cpu1 to turn off when load is less than or equal to 35 %. Useful to control power drain when you're listening to music when screen off, etc.
3) Tweak brightness Response Curve
Ex:
echo "30" > /sys/class/misc/brightness_curve/min_bl
echo "24" > /sys/class/misc/brightness_curve/max_gamma
This means any brightness value below 30 will have 0 gamma and brightness level above 30 will be linearly mapped to [0:24] gamma levels.
30 & 24 are stock values. Beta 16 will have voodoo color support as well. Use Voodo Screen Tuning R&D app from market to experiment and play around with yur SAMOLED screen.
4) Tweak Governors
Ex:
echo "85" > sys/devices/system/cpu/cpufreq/ondemandx/up_threshold
This means when ondemandx is used, the polling function scales cpu up to next frequency when cpu is 85% loaded w.r.t current frequency.
Many thanks to droidphile
Dear sir,
I have Sony SL, actually i have a problem with wifi as inserting sim card. I read many topics to find that is a common issue.
Some member has a fix. I fllowed their instruction but to no avail.
As i run the script, this happen :
Error resolving interpreter: /bin/sh does not exist
Using default shell
Exec sh '/sdcard/fix_country_code'
Fix_country_code'
Error: unable to open database "/data/data/com.android.providers.settings/databases/settings.db": unable to open database file
Killed
Killed
Orginally posted by DKTigra:
I wrote a short script (tried to run as init.d - but it has no sense as country code is beeing read from simcard when all init.d scripts are finished), so i used free Script Manager - SManager (https://play.google.com/store/apps/d....scriptmanager) to launch script after boot.
That's script code (just changed wifi_country_code location):
Code:
#!/bin/sh
sleep 10
sqlite3 /data/data/com.android.providers.settings/databases/settings.db "INSERT INTO global (name, value) VALUES ('wifi_country_code', 'EU');"
svc wifi disable
sleep 10
svc wifi enable
Also i've added sleep for 10 seconds for ensure that sim data is already read, and added wifi down - sleep - wifi up for reestablish network connection (as i'm using n/g network for old devices, so Nexus is connected in g-mode to my router when script is executed).
Instruction:
1. Download sqlite3 binary from any source (I've got it from xda http://forum.xda-developers.com/show...29&postcount=2) and move it to /system/xbin, set permissions 755 (rwx-rx-rx)
2. Save script to internal SD-card, f.e. as "fix_country_code.sh",
3. Install script-manager, that is able to run scripts on boot, and set to execute script with root rights (like on screenshot if SManager is used). Also it's possible to test script w/o reboot
Please help me
jad.smoke said:
Dear sir,
I have Sony SL, actually i have a problem with wifi as inserting sim card. I read many topics to find that is a common issue.
Some member has a fix. I fllowed their instruction but to no avail.
As i run the script, this happen :
Error resolving interpreter: /bin/sh does not exist
Using default shell
Exec sh '/sdcard/fix_country_code'
Fix_country_code'
Error: unable to open database "/data/data/com.android.providers.settings/databases/settings.db": unable to open database file
Killed
Killed
Orginally posted by DKTigra:
I wrote a short script (tried to run as init.d - but it has no sense as country code is beeing read from simcard when all init.d scripts are finished), so i used free Script Manager - SManager (https://play.google.com/store/apps/d....scriptmanager) to launch script after boot.
That's script code (just changed wifi_country_code location):
Code:
#!/bin/sh
sleep 10
sqlite3 /data/data/com.android.providers.settings/databases/settings.db "INSERT INTO global (name, value) VALUES ('wifi_country_code', 'EU');"
svc wifi disable
sleep 10
svc wifi enable
Also i've added sleep for 10 seconds for ensure that sim data is already read, and added wifi down - sleep - wifi up for reestablish network connection (as i'm using n/g network for old devices, so Nexus is connected in g-mode to my router when script is executed).
Instruction:
1. Download sqlite3 binary from any source (I've got it from xda http://forum.xda-developers.com/show...29&postcount=2) and move it to /system/xbin, set permissions 755 (rwx-rx-rx)
2. Save script to internal SD-card, f.e. as "fix_country_code.sh",
3. Install script-manager, that is able to run scripts on boot, and set to execute script with root rights (like on screenshot if SManager is used). Also it's possible to test script w/o reboot
Please help me
Click to expand...
Click to collapse
Helpppp
Well, i struggled for half a day relentlessly and finally got Reaver Working on my Xiaomi Mi4 android phone with a big help from the below mentioned link , everything is going good and fine, i got the Reaver app working on my Rooted app without bcmon and it worked and i'm ready to hack the network but just as i bypassed "Test Monitor" successfully(by loading a few scripts and debugging) and hit "Start Attack" this thing showed up, below i've written down the issue as it appeared since i'm not allowed to post screenshots & Links untill i make 10 posts(i'm a new user) and the scripts that i used to bypass Test Monitor are attached below, i'm basically a noob but good at technical things, the guide mentioned in the below link isn't as easy as it is told there, there are a few more steps that aren't added in the guide!!
HELP URGENTLY!!!! I waisted a whole day trying to get it working, i'd be so grateful :laugh: if you could help me out with it! PLEASE!! :crying:
Here are those scripts i loaded and put the phone on debug mode
Custom activation script:
#!/bin/bash
svc wifi disable
LD_LIBRARY_PATH=/data/data/com.bcmon.bcmon/files/libs
LD_PRELOAD=/data/data/com.bcmon.bcmon/files/libs/libfake_driver.so sh
cd /data/data/com.bcmon.bcmon/files/tools
./enable_bcmon
echo “rfasuccess”
exit
Custom Warm-up Script
#!/bin/bash
LD_LIBRARY_PATH=/data/data/com.bcmon.bcmon/files/libs
LD_PRELOAD=/data/data/com.bcmon.bcmon/files/libs/libfake_driver.so sh
cd /data/data/com.bcmon.bcmon/files/tools
Custom stop Script:
#!/bin/bash
svc wifi enable
echo “rfasuccess”
1. this happened first but i continued anyway.
Stdout:
"rfa success"
StdErr:
Control the Wifi manager
usage: svc wifi [enable[disable] Turn wifi on or off.
svc wifi prefer
set Wifi as the preferred data network
.//srart.shl[4]: sh :not found
.//start.sh[5]: cd: /data/data/com.bcmon.bcmon/files/tools : No Such File or Directory
./start.sh[6]: ./enable_bcmon : not found
2. and then this happened in the processing window
sh: <stdin>[3]: sh: not found
CANNOT LINK EXECUTABLE: could not load library "libcap.so.1" needed by "./reaver"; caused by library "libcap.so.1" not found
3. and finally when i hit stop, this message showed up
Stdout:
?rfasuccess?
StdErr:
Control the Wi-fi manager
usage: svc wifi[enable[disable]
Turn Wi-Fi on or off
svc wifi prefer
Set Wi-Fi as the preferred data network
These are the Steps i followed to get the monitoring mode done.
1.Download bcmon- (link)
2.Save the app on your sdcard but don’t install it.
3.download Reaver apk(RFA) and install it.- (link)
4.Download root explorer by speed speed software and install it.- (link)
6.Install and open bcmon app
keep it open for 5s and then press home.
(This will surely create a com.bcmon.bcmon folder in/Data/data)
7.Open root explorer and browse to the bcmon apk.
8.Select it and press view.
9.Open assets.
10.Copy all the files to /Data/data/com.bcmon.bcmon/files.
#If any file or folder of the same name is found then delete it#
/Now you’ll have to add custom scripts that I have given below(just copy them in a note editor and save with a .sh extension)
Start script-
Start script- mentioned above in custom start script
Warm script- mentioned above in custom warm up script
Stop script- mentioned above in custom stop script
#Now open root explorer
Browse to com.bcmon.bcmon/files/tools/reaver
Long press on it and press permissions and then check the execute boxes(all 3).now click OK.
Now in tools long press enable_bcmon and give it execute rights (all 3).now click OK .
#All set….now open reaver and scan for networks press on one with green color and with a good range.
Go to settings and monitor mode setting and unchek the use bcmon and load all the scripts properly.
#while loading scripts start.sh is the activation script,warm.sh is the warm up script and stop.sh is the stop script. #
Now scroll down and check the debugging mode.
#Go back to the attack screen and press test monitor mode.
Rfasuccess comes then press OK and press start attack.
#All done,now wait until it finds the routers key for you.
#This worked on my I ball slide 6318i,Alcatel ot 918n and redmi note.
goodpeace said:
Well, i struggled for half a day relentlessly and finally got Reaver Working on my Xiaomi Mi4 android phone with a big help from the below mentioned link , everything is going good and fine, i got the Reaver app working on my Rooted app without bcmon and it worked and i'm ready to hack the network but just as i bypassed "Test Monitor" successfully(by loading a few scripts and debugging) and hit "Start Attack" this thing showed up, below i've written down the issue as it appeared since i'm not allowed to post screenshots & Links untill i make 10 posts(i'm a new user) and the scripts that i used to bypass Test Monitor are attached below, i'm basically a noob but good at technical things, the guide mentioned in the below link isn't as easy as it is told there, there are a few more steps that aren't added in the guide!!
HELP URGENTLY!!!! I waisted a whole day trying to get it working, i'd be so grateful :laugh: if you could help me out with it! PLEASE!! :crying:
Here are those scripts i loaded and put the phone on debug mode
Custom activation script:
#!/bin/bash
svc wifi disable
LD_LIBRARY_PATH=/data/data/com.bcmon.bcmon/files/libs
LD_PRELOAD=/data/data/com.bcmon.bcmon/files/libs/libfake_driver.so sh
cd /data/data/com.bcmon.bcmon/files/tools
./enable_bcmon
echo “rfasuccess”
exit
Custom Warm-up Script
#!/bin/bash
LD_LIBRARY_PATH=/data/data/com.bcmon.bcmon/files/libs
LD_PRELOAD=/data/data/com.bcmon.bcmon/files/libs/libfake_driver.so sh
cd /data/data/com.bcmon.bcmon/files/tools
Custom stop Script:
#!/bin/bash
svc wifi enable
echo “rfasuccess”
1. this happened first but i continued anyway.
Stdout:
"rfa success"
StdErr:
Control the Wifi manager
usage: svc wifi [enable[disable] Turn wifi on or off.
svc wifi prefer
set Wifi as the preferred data network
.//srart.shl[4]: sh :not found
.//start.sh[5]: cd: /data/data/com.bcmon.bcmon/files/tools : No Such File or Directory
./start.sh[6]: ./enable_bcmon : not found
2. and then this happened in the processing window
sh: <stdin>[3]: sh: not found
CANNOT LINK EXECUTABLE: could not load library "libcap.so.1" needed by "./reaver"; caused by library "libcap.so.1" not found
3. and finally when i hit stop, this message showed up
Stdout:
?rfasuccess?
StdErr:
Control the Wi-fi manager
usage: svc wifi[enable[disable]
Turn Wi-Fi on or off
svc wifi prefer
Set Wi-Fi as the preferred data network
These are the Steps i followed to get the monitoring mode done.
1.Download bcmon- (link)
2.Save the app on your sdcard but don’t install it.
3.download Reaver apk(RFA) and install it.- (link)
4.Download root explorer by speed speed software and install it.- (link)
6.Install and open bcmon app
keep it open for 5s and then press home.
(This will surely create a com.bcmon.bcmon folder in/Data/data)
7.Open root explorer and browse to the bcmon apk.
8.Select it and press view.
9.Open assets.
10.Copy all the files to /Data/data/com.bcmon.bcmon/files.
#If any file or folder of the same name is found then delete it#
/Now you’ll have to add custom scripts that I have given below(just copy them in a note editor and save with a .sh extension)
Start script-
Start script- mentioned above in custom start script
Warm script- mentioned above in custom warm up script
Stop script- mentioned above in custom stop script
#Now open root explorer
Browse to com.bcmon.bcmon/files/tools/reaver
Long press on it and press permissions and then check the execute boxes(all 3).now click OK.
Now in tools long press enable_bcmon and give it execute rights (all 3).now click OK .
#All set….now open reaver and scan for networks press on one with green color and with a good range.
Go to settings and monitor mode setting and unchek the use bcmon and load all the scripts properly.
#while loading scripts start.sh is the activation script,warm.sh is the warm up script and stop.sh is the stop script. #
Now scroll down and check the debugging mode.
#Go back to the attack screen and press test monitor mode.
Rfasuccess comes then press OK and press start attack.
#All done,now wait until it finds the routers key for you.
#This worked on my I ball slide 6318i,Alcatel ot 918n and redmi note.
Click to expand...
Click to collapse
let me know as well if you find any solution.
i get frist error
Start .sh not found plzzz help me bro
Same here pal!
The person who posted this method is my frnd on FB , whenever I tried to connect he ignored my text.
Stucked at the same..
So I was having the same error as the couple people above me, but I was able to get Reaver to recognize where my files were. I moved it off of the SD card to: /data/data/com.bcmon.bcmon
Then I manually typed in the location path of my .sh files:
/data/data/com.bcmon.bcmon/start.sh
/data/data/com.bcmon.bcmon/warm.sh
/data/data/com.bcmon.bcmon/stop.sh
Obviously you'll want to put in whatever you named those files there.
So I've gotten past that hurtle. I am however stuck with this new set of errors now, although it will allow me to progress to "start attack".
I'm new so the site is preventing me from posting these links normally but here are the two errors I'm getting:
Code:
Stdout: rfasuccess
StdErr: Control the Wi-Fi manager
usage: svc wifi [enable|disable]
Turn Wi-Fi on or off
./data/data/com.bcmon.bcmon/start.sh[4]: sh : not found
./data/data/com.bcmon.bcmon/start.sh[5]: cd: /data/data/com.bcmon.bcmon/files/tools : no such file or directory
.data/data/com.bcmon.bcmon/start.sh[6]: ./enable_bcmon : not found
After this I am able to progress and next see:
Code:
tmp-mksh: <stdin>[3]: sh: not found
error: only position independent executables (PIE) are supported.
Any suggestions?
- HTC One M7vzw
PacMan Rom 5.1.1
Stucked at same place
:silly::silly:
Libcap.so.1 error please sort it out soon..
Does anyone managed to solve this?
Your scripts shebang points to /bin/bash you could try changing to #!/system/bin/sh which should hopefully solve the sh not found error. More recent android versions force pie executables as a tool to help lower hack risks, the option there is to try to bypass pie systemwide or get a pie executable. Libcap error is due to the file not being present I'm not sure if your app is supposed to include it but it's not a standard android library.
Hey please help can I use in Micromax canvas nitro A310
Err msg displayed... Plzzz help
:Hi, m a general user of an android phone (without much technical skills). I have tried the method suggested step by step for using Reaver Rfa without bcmon and it enabled monitor mode but after that a popup appeared, which was as followed (unable to attach screenshot)
Stdout:
StdErr:
bmon_wrapper_loaded
K_Shell/10118:1442:<Stdin>[4]:
iwconfig:not found
I am unable to understand it. Please help
goodpeace said:
Well, i struggled for half a day relentlessly and finally got Reaver Working on my Xiaomi Mi4 android phone with a big help from the below mentioned link , everything is going good and fine, i got the Reaver app working on my Rooted app without bcmon and it worked and i'm ready to hack the network but just as i bypassed "Test Monitor" successfully(by loading a few scripts and debugging) and hit "Start Attack" this thing showed up, below i've written down the issue as it appeared since i'm not allowed to post screenshots & Links untill i make 10 posts(i'm a new user) and the scripts that i used to bypass Test Monitor are attached below, i'm basically a noob but good at technical things, the guide mentioned in the below link isn't as easy as it is told there, there are a few more steps that aren't added in the guide!!
HELP URGENTLY!!!! I waisted a whole day trying to get it working, i'd be so grateful :laugh: if you could help me out with it! PLEASE!! :crying:
Here are those scripts i loaded and put the phone on debug mode
Custom activation script:
#!/bin/bash
svc wifi disable
LD_LIBRARY_PATH=/data/data/com.bcmon.bcmon/files/libs
LD_PRELOAD=/data/data/com.bcmon.bcmon/files/libs/libfake_driver.so sh
cd /data/data/com.bcmon.bcmon/files/tools
./enable_bcmon
echo “rfasuccess”
exit
Custom Warm-up Script
#!/bin/bash
LD_LIBRARY_PATH=/data/data/com.bcmon.bcmon/files/libs
LD_PRELOAD=/data/data/com.bcmon.bcmon/files/libs/libfake_driver.so sh
cd /data/data/com.bcmon.bcmon/files/tools
Custom stop Script:
#!/bin/bash
svc wifi enable
echo “rfasuccess”
1. this happened first but i continued anyway.
Stdout:
"rfa success"
StdErr:
Control the Wifi manager
usage: svc wifi [enable[disable] Turn wifi on or off.
svc wifi prefer
set Wifi as the preferred data network
.//srart.shl[4]: sh :not found
.//start.sh[5]: cd: /data/data/com.bcmon.bcmon/files/tools : No Such File or Directory
./start.sh[6]: ./enable_bcmon : not found
2. and then this happened in the processing window
sh: <stdin>[3]: sh: not found
CANNOT LINK EXECUTABLE: could not load library "libcap.so.1" needed by "./reaver"; caused by library "libcap.so.1" not found
3. and finally when i hit stop, this message showed up
Stdout:
?rfasuccess?
StdErr:
Control the Wi-fi manager
usage: svc wifi[enable[disable]
Turn Wi-Fi on or off
svc wifi prefer
Set Wi-Fi as the preferred data network
These are the Steps i followed to get the monitoring mode done.
1.Download bcmon- (link)
2.Save the app on your sdcard but don’t install it.
3.download Reaver apk(RFA) and install it.- (link)
4.Download root explorer by speed speed software and install it.- (link)
6.Install and open bcmon app
keep it open for 5s and then press home.
(This will surely create a com.bcmon.bcmon folder in/Data/data)
7.Open root explorer and browse to the bcmon apk.
8.Select it and press view.
9.Open assets.
10.Copy all the files to /Data/data/com.bcmon.bcmon/files.
#If any file or folder of the same name is found then delete it#
/Now you’ll have to add custom scripts that I have given below(just copy them in a note editor and save with a .sh extension)
Start script-
Start script- mentioned above in custom start script
Warm script- mentioned above in custom warm up script
Stop script- mentioned above in custom stop script
#Now open root explorer
Browse to com.bcmon.bcmon/files/tools/reaver
Long press on it and press permissions and then check the execute boxes(all 3).now click OK.
Now in tools long press enable_bcmon and give it execute rights (all 3).now click OK .
#All set….now open reaver and scan for networks press on one with green color and with a good range.
Go to settings and monitor mode setting and unchek the use bcmon and load all the scripts properly.
#while loading scripts start.sh is the activation script,warm.sh is the warm up script and stop.sh is the stop script. #
Now scroll down and check the debugging mode.
#Go back to the attack screen and press test monitor mode.
Rfasuccess comes then press OK and press start attack.
#All done,now wait until it finds the routers key for you.
#This worked on my I ball slide 6318i,Alcatel ot 918n and redmi note.
Click to expand...
Click to collapse
Please explain step by step on how you did this I'm stuck. Thanks.
BiteMyCAPTCHA said:
So I was having the same error as the couple people above me, but I was able to get Reaver to recognize where my files were. I moved it off of the SD card to: /data/data/com.bcmon.bcmon
Then I manually typed in the location path of my .sh files:
/data/data/com.bcmon.bcmon/start.sh
/data/data/com.bcmon.bcmon/warm.sh
/data/data/com.bcmon.bcmon/stop.sh
Obviously you'll want to put in whatever you named those files there.
So I've gotten past that hurtle. I am however stuck with this new set of errors now, although it will allow me to progress to "start attack".
I'm new so the site is preventing me from posting these links normally but here are the two errors I'm getting:
Code:
Stdout: rfasuccess
StdErr: Control the Wi-Fi manager
usage: svc wifi [enable|disable]
Turn Wi-Fi on or off
./data/data/com.bcmon.bcmon/start.sh[4]: sh : not found
./data/data/com.bcmon.bcmon/start.sh[5]: cd: /data/data/com.bcmon.bcmon/files/tools : no such file or directory
.data/data/com.bcmon.bcmon/start.sh[6]: ./enable_bcmon : not found
After this I am able to progress and next see:
Code:
tmp-mksh: <stdin>[3]: sh: not found
error: only position independent executables (PIE) are supported.
Any suggestions?
- HTC One M7vzw
PacMan Rom 5.1.1
Click to expand...
Click to collapse
Dude..
This is the same error that mentioned in the post
---------- Post added at 08:54 AM ---------- Previous post was at 08:53 AM ----------
10258Smoker said:
Libcap.so.1 error please sort it out soon..
Click to expand...
Click to collapse
find out libcap.so.1 from bcmon assets and put it on system/lib
How to copy bcmon files from rootex, there's no copy option, only extract.
goodpeace said:
Well, i struggled for half a day relentlessly and finally got Reaver Working on my Xiaomi Mi4 android phone with a big help from the below mentioned link , everything is going good and fine, i got the Reaver app working on my Rooted app without bcmon and it worked and i'm ready to hack the network but just as i bypassed "Test Monitor" successfully(by loading a few scripts and debugging) and hit "Start Attack" this thing showed up, below i've written down the issue as it appeared since i'm not allowed to post screenshots & Links untill i make 10 posts(i'm a new user) and the scripts that i used to bypass Test Monitor are attached below, i'm basically a noob but good at technical things, the guide mentioned in the below link isn't as easy as it is told there, there are a few more steps that aren't added in the guide!!
HELP URGENTLY!!!! I waisted a whole day trying to get it working, i'd be so grateful :laugh: if you could help me out with it! PLEASE!! :crying:
Here are those scripts i loaded and put the phone on debug mode
Custom activation script:
#!/bin/bash
svc wifi disable
LD_LIBRARY_PATH=/data/data/com.bcmon.bcmon/files/libs
LD_PRELOAD=/data/data/com.bcmon.bcmon/files/libs/libfake_driver.so sh
cd /data/data/com.bcmon.bcmon/files/tools
./enable_bcmon
echo “rfasuccess”
exit
Custom Warm-up Script
#!/bin/bash
LD_LIBRARY_PATH=/data/data/com.bcmon.bcmon/files/libs
LD_PRELOAD=/data/data/com.bcmon.bcmon/files/libs/libfake_driver.so sh
cd /data/data/com.bcmon.bcmon/files/tools
Custom stop Script:
#!/bin/bash
svc wifi enable
echo “rfasuccess”
1. this happened first but i continued anyway.
Stdout:
"rfa success"
StdErr:
Control the Wifi manager
usage: svc wifi [enable[disable] Turn wifi on or off.
svc wifi prefer
set Wifi as the preferred data network
.//srart.shl[4]: sh :not found
.//start.sh[5]: cd: /data/data/com.bcmon.bcmon/files/tools : No Such File or Directory
./start.sh[6]: ./enable_bcmon : not found
2. and then this happened in the processing window
sh: <stdin>[3]: sh: not found
CANNOT LINK EXECUTABLE: could not load library "libcap.so.1" needed by "./reaver"; caused by library "libcap.so.1" not found
3. and finally when i hit stop, this message showed up
Stdout:
?rfasuccess?
StdErr:
Control the Wi-fi manager
usage: svc wifi[enable[disable]
Turn Wi-Fi on or off
svc wifi prefer
Set Wi-Fi as the preferred data network
These are the Steps i followed to get the monitoring mode done.
1.Download bcmon- (link)
2.Save the app on your sdcard but don’t install it.
3.download Reaver apk(RFA) and install it.- (link)
4.Download root explorer by speed speed software and install it.- (link)
6.Install and open bcmon app
keep it open for 5s and then press home.
(This will surely create a com.bcmon.bcmon folder in/Data/data)
7.Open root explorer and browse to the bcmon apk.
8.Select it and press view.
9.Open assets.
10.Copy all the files to /Data/data/com.bcmon.bcmon/files.
#If any file or folder of the same name is found then delete it#
/Now you’ll have to add custom scripts that I have given below(just copy them in a note editor and save with a .sh extension)
Start script-
Start script- mentioned above in custom start script
Warm script- mentioned above in custom warm up script
Stop script- mentioned above in custom stop script
#Now open root explorer
Browse to com.bcmon.bcmon/files/tools/reaver
Long press on it and press permissions and then check the execute boxes(all 3).now click OK.
Now in tools long press enable_bcmon and give it execute rights (all 3).now click OK .
#All set….now open reaver and scan for networks press on one with green color and with a good range.
Go to settings and monitor mode setting and unchek the use bcmon and load all the scripts properly.
#while loading scripts start.sh is the activation script,warm.sh is the warm up script and stop.sh is the stop script. #
Now scroll down and check the debugging mode.
#Go back to the attack screen and press test monitor mode.
Rfasuccess comes then press OK and press start attack.
#All done,now wait until it finds the routers key for you.
#This worked on my I ball slide 6318i,Alcatel ot 918n and redmi note.
Click to expand...
Click to collapse
Could anyone tell me how to copy bcmon assets files from sd card to data, because all the options says is extract.
Please help meeee...!
Possible Fix for libcap.so.1 problem
By moving "libcap.so.1", "libsqlite3.so.0" from "/data/data/com.bcmon.bcmon/files/libs" to "/system/lib" and setting the wifi-interface in the "Monitor-Mode settings" to "wlan0". I was able to solve the "libcap.so.1" error.
Straight afterwards, I got the "<stdin>[3] : not found" error.
By changing the "start.sh" script from :
Code:
#!/bin/bash
svc wifi disable
LD_LIBRARY_PATH=/data/data/com.bcmon.bcmon/files/libs
LD_PRELOAD=/data/data/com.bcmon.bcmon/files/libs/libfake_driver.so sh
cd /data/data/com.bcmon.bcmon/files/tools
./enable_bcmon
echo “rfasuccess”
exit
--to--
Code:
#!/bin/bash
svc wifi enable
LD_LIBRARY_PATH=/data/data/com.bcmon.bcmon/files/libs
LD_PRELOAD=/data/data/com.bcmon.bcmon/files/libs/libfake_driver.so sh
cd /data/data/com.bcmon.bcmon/files/tools
./enable_bcmon
echo “rfasuccess”
exit
I was able to pass the "<stdin>[3] : not found" error but now it is stuck on "Waiting for beacon from <Mac Address here>".
I've tried multiple router and waited around 15 minutes on that screen for each router with my phone next to them but it will not get pass that line.
Galaxy s3 i9300 here.
script errors
start.sh, warm.sh and stop.sh are not functioning properly, I am stuck at the same stage as you are and a can't even run the scripts on the terminal emulator.
I have tried granting permissions to the scripts but is is giving errors, if you enable "debug mode", you will see that not even one command is being issued without errors.
BatDroid said:
After this I am able to progress and next see:
Any suggestions?
- HTC One M7vzw
PacMan Rom 5.1.1
Dude..
This is the same error that mentioned in the post
---------- Post added at 08:54 AM ---------- Previous post was at 08:53 AM ----------
find out libcap.so.1 from bcmon assets and put it on system/lib
Click to expand...
Click to collapse
How do I fix the PIE problem? I'm using a Moto E LTE Surnia with CM13.
I cant copy files from extracted folder/asset folder of "bcmon" from any root explorer even from premium root explorer by speedspeed software. Please help me with this. Thank you in advance.
No app in market that can hack wifi password.
Don't waste time.
New wifi routers have WPA 2PSK highest security current time. To crack this type of password may take 2 mintues to many of years depend on which type of character and length have been chosen. All the procedure of cracking password done on linux platform.
In my opinion there are lots of apps on playstore are fake promising to crack wifi password.
Because wifi wpa2psk generate new reandoms keys with 24 or more characters changes with time to time (2-5 sec). And this keys doesn't not save in android in any way. So, how can you say this app hack wifi passwords.
If wifi router has WEP protected security then it can be easily cracked in 2 min any password.