Hello guys,
I've got a big problem with my I9300 and therefore I would like to ask here for any help. (If I'm in the wrong section, please move the thread to a correct one)
I had installed the Resurrection Remix ROM, v5.2.6. from 30.12.2014 and Googy-Max 2 recovery (CWM based) on my phone. I was using it for days and all worked fine.
One day I turned the phone off and I wanted to restart it. But it never restarted again; it ends up in a boot loop. It shows me the white Samsung Boot-Logo for some seconds, then a total black screen and the same thing repeats in a loop.
So I wanted to get into the recovery for wiping etc. but I couldn’t access the recovery. Nothing happens by pressing the relevant buttons. The device is still hanging in the boot loop. So I wanted to flash via Odin, but this isn't possible. I also can't go into the download mode. After pressing the relevant buttons, the green warning screen appears, which asks me if I really want to go to the download mode. But when I press volume up for "continue" or even if I don't press anything, the phone turns off and the boot loop with the white Samsung Logo starts again.
Therefore I ordered a USB JIG for forcing the device to go into download mode. When I plug the USB JIG in, the device actually goes into download mode but this status holds on only for a few seconds. After accessing download mode through the JIG, after a few seconds the phone turns off, restarts, (and because the JIG is still plugged in) the download mode appears again and it ends in a loop.
At first I thought maybe the power button is sticking and therefore the device turns on and off autonomous. But definitively I can negate it, because I opened the phone and removed the power button and nothing changed. Also by pressing the power button on the mainboard I can clearly hear the "click".
So I started a new attempt. Although the time, in which the device stays in download mode before turning off, is very short (only a few seconds), I tried flashing an other recovery, namely TWRP v2.8.3.0. So I prepared ODIN, plugged the JIG into the device, by appearing the download mode I switched cables and an other person clicked start at ODIN and it worked. So now TWRP is installed. Now I also can't get into recovery but after flashing TWRP there exist two little differences. First, after pressing the relevant buttons, TWRP appears for less than 1 second until the phone turns off. Secondly, when I plug the device in for charging, the Samsung charging logo appears for some seconds, then for less than 1 second appears a charging logo from Lollipop and the device ends up in a loop by displaying alternately the two different charging logos. Before flashing TWRP, the device booted in a boot loop (as I wrote above) by plugging it in for charging.
So the main question: how can I get my device work again
I tried telling you all details so that you have a better view of the problem.
Maybe I should flash a fully (stock) rom, but as I told you the download mode appears only for a few seconds. Flashing a recovery was possible, because the recovery file is very small - 7 MB. A full rom is much bigger and I think by flashing a complete rom, the device would turn off while Odin is flashing, therefore I ask first here for any assistance.
Thank you very much in advance!
beginnerteur said:
Hello guys,
I've got a big problem with my I9300 and therefore I would like to ask here for any help. (If I'm in the wrong section, please move the thread to a correct one)
I had installed the Resurrection Remix ROM, v5.2.6. from 30.12.2014 and Googy-Max 2 recovery (CWM based) on my phone. I was using it for days and all worked fine.
One day I turned the phone off and I wanted to restart it. But it never restarted again; it ends up in a boot loop. It shows me the white Samsung Boot-Logo for some seconds, then a total black screen and the same thing repeats in a loop.
So I wanted to get into the recovery for wiping etc. but I couldn’t access the recovery. Nothing happens by pressing the relevant buttons. The device is still hanging in the boot loop. So I wanted to flash via Odin, but this isn't possible. I also can't go into the download mode. After pressing the relevant buttons, the green warning screen appears, which asks me if I really want to go to the download mode. But when I press volume up for "continue" or even if I don't press anything, the phone turns off and the boot loop with the white Samsung Logo starts again.
Therefore I ordered a USB JIG for forcing the device to go into download mode. When I plug the USB JIG in, the device actually goes into download mode but this status holds on only for a few seconds. After accessing download mode through the JIG, after a few seconds the phone turns off, restarts, (and because the JIG is still plugged in) the download mode appears again and it ends in a loop.
At first I thought maybe the power button is sticking and therefore the device turns on and off autonomous. But definitively I can negate it, because I opened the phone and removed the power button and nothing changed. Also by pressing the power button on the mainboard I can clearly hear the "click".
So I started a new attempt. Although the time, in which the device stays in download mode before turning off, is very short (only a few seconds), I tried flashing an other recovery, namely TWRP v2.8.3.0. So I prepared ODIN, plugged the JIG into the device, by appearing the download mode I switched cables and an other person clicked start at ODIN and it worked. So now TWRP is installed. Now I also can't get into recovery but after flashing TWRP there exist two little differences. First, after pressing the relevant buttons, TWRP appears for less than 1 second until the phone turns off. Secondly, when I plug the device in for charging, the Samsung charging logo appears for some seconds, then for less than 1 second appears a charging logo from Lollipop and the device ends up in a loop by displaying alternately the two different charging logos. Before flashing TWRP, the device booted in a boot loop (as I wrote above) by plugging it in for charging.
So the main question: how can I get my device work again
I tried telling you all details so that you have a better view of the problem.
Maybe I should flash a fully (stock) rom, but as I told you the download mode appears only for a few seconds. Flashing a recovery was possible, because the recovery file is very small - 7 MB. A full rom is much bigger and I think by flashing a complete rom, the device would turn off while Odin is flashing, therefore I ask first here for any assistance.
Thank you very much in advance!
Click to expand...
Click to collapse
Check and make sure that your volume buttons and home button are not stuck also. If they are not, I would suggest a visit to a repair shop as your EMMC chip might be weak already.
beginnerteur said:
Hello guys,
I've got a big problem with my I9300 and therefore I would like to ask here for any help. (If I'm in the wrong section, please move the thread to a correct one)
I had installed the Resurrection Remix ROM, v5.2.6. from 30.12.2014 and Googy-Max 2 recovery (CWM based) on my phone. I was using it for days and all worked fine.
One day I turned the phone off and I wanted to restart it. But it never restarted again; it ends up in a boot loop. It shows me the white Samsung Boot-Logo for some seconds, then a total black screen and the same thing repeats in a loop.
So I wanted to get into the recovery for wiping etc. but I couldn’t access the recovery. Nothing happens by pressing the relevant buttons. The device is still hanging in the boot loop. So I wanted to flash via Odin, but this isn't possible. I also can't go into the download mode. After pressing the relevant buttons, the green warning screen appears, which asks me if I really want to go to the download mode. But when I press volume up for "continue" or even if I don't press anything, the phone turns off and the boot loop with the white Samsung Logo starts again.
Therefore I ordered a USB JIG for forcing the device to go into download mode. When I plug the USB JIG in, the device actually goes into download mode but this status holds on only for a few seconds. After accessing download mode through the JIG, after a few seconds the phone turns off, restarts, (and because the JIG is still plugged in) the download mode appears again and it ends in a loop.
At first I thought maybe the power button is sticking and therefore the device turns on and off autonomous. But definitively I can negate it, because I opened the phone and removed the power button and nothing changed. Also by pressing the power button on the mainboard I can clearly hear the "click".
So I started a new attempt. Although the time, in which the device stays in download mode before turning off, is very short (only a few seconds), I tried flashing an other recovery, namely TWRP v2.8.3.0. So I prepared ODIN, plugged the JIG into the device, by appearing the download mode I switched cables and an other person clicked start at ODIN and it worked. So now TWRP is installed. Now I also can't get into recovery but after flashing TWRP there exist two little differences. First, after pressing the relevant buttons, TWRP appears for less than 1 second until the phone turns off. Secondly, when I plug the device in for charging, the Samsung charging logo appears for some seconds, then for less than 1 second appears a charging logo from Lollipop and the device ends up in a loop by displaying alternately the two different charging logos. Before flashing TWRP, the device booted in a boot loop (as I wrote above) by plugging it in for charging.
So the main question: how can I get my device work again
I tried telling you all details so that you have a better view of the problem.
Maybe I should flash a fully (stock) rom, but as I told you the download mode appears only for a few seconds. Flashing a recovery was possible, because the recovery file is very small - 7 MB. A full rom is much bigger and I think by flashing a complete rom, the device would turn off while Odin is flashing, therefore I ask first here for any assistance.
Thank you very much in advance!
Click to expand...
Click to collapse
Your power button is failing, stuck in 'pressed' position. Try pressing repeatedly power button for several seconds, then release it completely. It shall bring it back to life. Visit your local service, or prepare tin, heat gun and soldering pistol. One button cost $0.2, they are selling them on eBay in sets of three (and 10, and 100....).
Happened to me some time ago, and video on youtube helped me to dismantle my phone, pull broken button out of it, and change it for new.
My phone was cycling like yours.
beginnerteur said:
Hello guys,
I've got a big problem with my I9300 and therefore I would like to ask here for any help. (If I'm in the wrong section, please move the thread to a correct one)
I had installed the Resurrection Remix ROM, v5.2.6. from 30.12.2014 and Googy-Max 2 recovery (CWM based) on my phone. I was using it for days and all worked fine.
One day I turned the phone off and I wanted to restart it. But it never restarted again; it ends up in a boot loop. It shows me the white Samsung Boot-Logo for some seconds, then a total black screen and the same thing repeats in a loop.
So I wanted to get into the recovery for wiping etc. but I couldn’t access the recovery. Nothing happens by pressing the relevant buttons. The device is still hanging in the boot loop. So I wanted to flash via Odin, but this isn't possible. I also can't go into the download mode. After pressing the relevant buttons, the green warning screen appears, which asks me if I really want to go to the download mode. But when I press volume up for "continue" or even if I don't press anything, the phone turns off and the boot loop with the white Samsung Logo starts again.
Therefore I ordered a USB JIG for forcing the device to go into download mode. When I plug the USB JIG in, the device actually goes into download mode but this status holds on only for a few seconds. After accessing download mode through the JIG, after a few seconds the phone turns off, restarts, (and because the JIG is still plugged in) the download mode appears again and it ends in a loop.
At first I thought maybe the power button is sticking and therefore the device turns on and off autonomous. But definitively I can negate it, because I opened the phone and removed the power button and nothing changed. Also by pressing the power button on the mainboard I can clearly hear the "click".
So I started a new attempt. Although the time, in which the device stays in download mode before turning off, is very short (only a few seconds), I tried flashing an other recovery, namely TWRP v2.8.3.0. So I prepared ODIN, plugged the JIG into the device, by appearing the download mode I switched cables and an other person clicked start at ODIN and it worked. So now TWRP is installed. Now I also can't get into recovery but after flashing TWRP there exist two little differences. First, after pressing the relevant buttons, TWRP appears for less than 1 second until the phone turns off. Secondly, when I plug the device in for charging, the Samsung charging logo appears for some seconds, then for less than 1 second appears a charging logo from Lollipop and the device ends up in a loop by displaying alternately the two different charging logos. Before flashing TWRP, the device booted in a boot loop (as I wrote above) by plugging it in for charging.
So the main question: how can I get my device work again
I tried telling you all details so that you have a better view of the problem.
Maybe I should flash a fully (stock) rom, but as I told you the download mode appears only for a few seconds. Flashing a recovery was possible, because the recovery file is very small - 7 MB. A full rom is much bigger and I think by flashing a complete rom, the device would turn off while Odin is flashing, therefore I ask first here for any assistance.
Thank you very much in advance!
Click to expand...
Click to collapse
As said your emmc chip maybe failing.
The dead boot thread maybe of interest to you.
Virnik0 said:
Your power button is failing, stuck in 'pressed' position. Try pressing repeatedly power button for several seconds, then release it completely. It shall bring it back to life. Visit your local service, or prepare tin, heat gun and soldering pistol. One button cost $0.2, they are selling them on eBay in sets of three (and 10, and 100....).
Happened to me some time ago, and video on youtube helped me to dismantle my phone, pull broken button out of it, and change it for new.
My phone was cycling like yours.
Click to expand...
Click to collapse
He said he has tested this and can also hear the micro-switch clicking.
scorpionhd2 said:
Check and make sure that your volume buttons and home button are not stuck also. If they are not, I would suggest a visit to a repair shop as your EMMC chip might be weak already.
Click to expand...
Click to collapse
Virnik0 said:
Your power button is failing, stuck in 'pressed' position. Try pressing repeatedly power button for several seconds, then release it completely. It shall bring it back to life. Visit your local service, or prepare tin, heat gun and soldering pistol. One button cost $0.2, they are selling them on eBay in sets of three (and 10, and 100....).
Happened to me some time ago, and video on youtube helped me to dismantle my phone, pull broken button out of it, and change it for new.
My phone was cycling like yours.
Click to expand...
Click to collapse
Darke5tShad0w said:
As said your emmc chip maybe failing.
The dead boot thread maybe of interest to you.
He said he has tested this and can also hear the micro-switch clicking.
Click to expand...
Click to collapse
Thank you very much for helping! :good:
So the question is, whether it's the power button's or emmc's fault...
I did a little searching and found this video. I've got exactly the same problem like the guy. At 1:06 following the boot loop, at 1:34 following the problem with downlod mode.
Although he thinks it's caused to the sudden death problem, but at least in my case I think it's wrong because months ago I did the eMMC Brickbug Check.
Also I noticed a probably important detail. When I put the battery in the phone, it automatically turns on without pressing the power button like in 1:04-1:09 in the video. Which normal working phone turns itself on by simply putting in the battery...?
So it must get a command for turning on - (possibly through a defect power button?)
@Virnik0, do you remember, if you could hear the micro-switch clicking on your phone before replacing the button on the mainboard?
beginnerteur said:
Also I noticed a probably important detail. When I put the battery in the phone, it automatically turns on without pressing the power button
Click to expand...
Click to collapse
Your power button is faulty, replace it before you try fixing anything else.
Thank you very, very much for helping! :good: :good: :good:
Truly the power button was fault although you could hear clearly the "click".
I unsoldered and removed the power module and (by startig with JIG and rebooting via ADB) the phone works as it should. :victory:
Now I'm trying to solder a new power button......it's a bit tricky
Again, thank you very much guys!
I had the same problem, pressed the button many times, and it helped. Thank you for your suggestions
Related
Hi guys,
I figured I'll post again here since I think I bricked my phone.... I was trying to install Eugene's Vibrant6.zip and I got stuck on the Vibrant Logo with Samsung at the bottom. I tried to reset with both volume buttons and power button and got to grey battery and nothing else...
What I did prior to this was I formatted system and data on the recovery screen as per some posts here and it would just boot into a loop. Windows won't recognize a device and it just shows grey battery image and it doesn't seem to be charging. Anyone can help me?
EDIT:
Out and in the battery, plugged in to USB and it just loads the battery image and it's all grey color as if fully discharged and just stuck on it. Device is also not found in my system so I can't do any adb commands. If I just reset it without the cable it would just sit on the Samsung boot loop. Anything I can do?
UPDATE: Ok, some good news! I heard the sound as it connected via USB, I can see the 2 drives, but they read as Removable Disk and I can't access them...
adb reboot recovery or download
error: device not found
What if simply format the drives via Windows right click menu? Will that do any good or bad? What are my options here? Any help will be appreciated!
UPDATE: Well... looks like this is pretty much a dead phone.... I right clicked and selected Format in My Computer and it just says There is no disk in Driver F: Insert a disk and try again.
Can I a mount an image somehow via MagicISO? Or is there something simpler that I just can't figure out?
Again, thanks for your help!
Thanks.
Has anyone experienced this or am I the only one?
M5devil said:
Has anyone experienced this or am I the only one?
Click to expand...
Click to collapse
Sorry I have never heard of this or witnessed it while flashing anything to my device. Obviously the battery screen signifies that the phone is off but is in charging mode and hitting the power button will boot the device up. (I'm sure you already know of this). Never heard of it being stuck at that screen after flashing. Hopefully you can get this solved soon. Good luck
M5devil said:
Hi guys,
I figured I'll post again here since I think I bricked my phone.... I was trying to install Eugene's Vibrant6.zip and I got stuck on the Vibrant Logo with Samsung at the bottom. I tried to reset with both volume buttons and power button and got to grey battery and nothing else...
What I did prior to this was I formatted system and data on the recovery screen as per some posts here and it would just boot into a loop. Windows won't recognize a device and it just shows grey battery image and it doesn't seem to be charging. Anyone can help me?
EDIT:
Out and in the battery, plugged in to USB and it just loads the battery image and it's all grey color as if fully discharged and just stuck on it. Device is also not found in my system so I can't do any adb commands. If I just reset it without the cable it would just sit on the Samsung boot loop. Anything I can do?
UPDATE: Ok, some good news! I heard the sound as it connected via USB, I can see the 2 drives, but they read as Removable Disk and I can't access them...
adb reboot recovery or download
error: device not found
What if simply format the drives via Windows right click menu? Will that do any good or bad? What are my options here? Any help will be appreciated!
UPDATE: Well... looks like this is pretty much a dead phone.... I right clicked and selected Format in My Computer and it just says There is no disk in Driver F: Insert a disk and try again.
Can I a mount an image somehow via MagicISO? Or is there something simpler that I just can't figure out?
Again, thanks for your help!
Thanks.
Click to expand...
Click to collapse
Slow down for a second. Your phone is definitely not bricked. Ive been over the edge, and been able to bring my phone back to life.
To clarify, you flashed vibrant6.zip through clockwork mod, and then the phone got stuck on the samsung S? How long did you let it sit there?
It sounds like just your ROM is messed up.
Are you able to "get into recovery"? Holding both volume buttons while you power on the phone, without it being plugged into usb.
Do you have Odin? And have you ever used it?
Its totally frustrating when your phone gets messed up and you don't know what to do.
I flashed the stock ROM via Odin and then wanted to install Vibrant6.zip. For that I entered into a recovery mode via Clockwork and as someone in the other thread advised, I formatted system and also data, don't recall exactly. Then it looped to a standard recovery mode and I just rebooted the phone. This is where it got stuck... Vibrant in the center and Samsung at the bottom of the screen. To test it I left it like that from night till this morning. In the morning I woke up it was on the same boot screen.
Before that at night, after seeing it hand at the boot, I held both volume keys and power, waited for it to reboot, and immediately it showed a circular progress bar, but not moving just highlighted the 12 o'clock bar and second later I see the battery image all in gray and nothing else. It just sits on that grey static image without actually charging it (no green section or flashing dots)
Boot logo only appears if I am trying to reset without the USB cable. On the boot loop I plug in the cable and I hear the USB connecting it, I see the 2 Removable disks, but both inaccessible and adb commands don't recognize the device.
Very weird, as in turned off mode it's not charging at all.. just shows this grey battery image with a circle progress froze on 12 o'clock bar.
That's pretty much it.... I was never able to enter into recovery nor download via the buttons. It would just always reboot into this grey battery screen....
Completely helpless.... I did order a new battery from TMO, maybe the battery is fried and that's why it's not charging and just sits on this stupid static grey battery screen.
ArbitrageMan said:
It sounds like just your ROM is messed up.
Are you able to "get into recovery"? Holding both volume buttons while you power on the phone, without it being plugged into usb.
Do you have Odin? And have you ever used it?
Its totally frustrating when your phone gets messed up and you don't know what to do.
Click to expand...
Click to collapse
Holding both volume keys and releasing power once screen goes blank, only show Vibrant logo again... I have tried this a million times
With USB cable it shows grey battery screen, without the cable just a Vibrant boot loop...
I'm assuming that you have the Samsung drivers installed.
Try the following steps:
Take out the battery and then put it back in but don't turn the phone on.
Plug it via USB.. does anything show up on the screen?
zephiK said:
I'm assuming that you have the Samsung drivers installed.
Try the following steps:
Take out the battery and then put it back in but don't turn the phone on.
Plug it via USB.. does anything show up on the screen?
Click to expand...
Click to collapse
Yes, I have the drivers installed as I was able to locate my device and use adb commands to enter into recovery and download. Also Kies worked.
Doing what you asked simply load the grey battery image and nothing else with a progress bar not spinning. Just sort of hangs on this image and that's all.
Booting without the USB cable loads the Vibrant boot loop. Connecting USB at this boot loop state, would play a sound as if it connected to my windows, but I can only see Removable disks that are inaccessible and adb doesn't find the device...
Very strange.... trying to use the button keys to enter into recovery or download is no use, as that just won't ever happen, even when phone was working fine.
Any other suggestions? I would return the phone for replacement... but I am not sure how it would look with all the files still on the internal disk including root if I am not mistaken... I had only few hours of sleep because of this headache
M5devil said:
Yes, I have the drivers installed as I was able to locate my device and use adb commands to enter into recovery and download. Also Kies worked.
Doing what you asked simply load the grey battery image and nothing else with a progress bar not spinning. Just sort of hangs on this image and that's all.
Booting without the USB cable loads the Vibrant boot loop. Connecting USB at this boot loop state, would play a sound as if it connected to my windows, but I can only see Removable disks that are inaccessible and adb doesn't find the device...
Very strange.... trying to use the button keys to enter into recovery or download is no use, as that just won't ever happen, even when phone was working fine.
Any other suggestions? I would return the phone for replacement... but I am not sure how it would look with all the files still on the internal disk including root if I am not mistaken... I had only few hours of sleep because of this headache
Click to expand...
Click to collapse
Are you sure that you're doing the right things to get to download? I've been in this situation and I wasn't able to get into recovery but I was able to get back into download mode.
I believe if you return it back and they find out it was rooted, they will charge you for it. If not, it'll appear on your bill.
I'm sure that you're doing the wrong things to get into download mode. If something is appearing on your screen it is a soft-brick and you're not bricked.
1. Take out battery, put it back in. (to turn the phone fully off)
2. Don't turn it the phone on!
3. Plug the phone into your PC, do not hit the power button!
4. See if the phone shows anything on the screen (powers on its own when plugged in)
IF the phone screen does 'turn on' after being plugged in without you hitting the power button, so far so good.
5. Now while it's on like this, hold the volume up and volume down buttons.
6. Hold the power button as well as the volume buttons until the screen goes black.
7. As soon as the screen goes black, let go of the power button! But DON'T let go of the volume buttons!
Click to expand...
Click to collapse
A tip to get into download mode is to put the phone HORIZONTALLY (sideways) and it will make it a lot easier.
I am pretty much positive about it. I know a lot of people can easily enter into recovery or download modes, but I know many can't and I am one of them. It would just load the grey battery image instantly as I let go of the power button.
1. Take out battery, put it back in. (to turn the phone fully off) DONE
2. Don't turn it the phone on! DONE
3. Plug the phone into your PC, do not hit the power button! DONE
4. See if the phone shows anything on the screen (powers on its own when plugged in) FIRST THING THAT APPEARS IS A CIRCULAR PROGRESS BAR THAT CHANGES TO A GREY BATTERY IMAGE WITH A BAR IN THE MIDDLE OF IT. STATIC IMAGE, NOTHING ELSE.
IF the phone screen does 'turn on' after being plugged in without you hitting the power button, so far so good.
5. Now while it's on like this, hold the volume up and volume down buttons. DONE
6. Hold the power button as well as the volume buttons until the screen goes black. DONE
7. As soon as the screen goes black, let go of the power button! But DON'T let go of the volume buttons! DONE
THE STUPID GREY COLOR BATTERY IMAGE APPEARS AS BEFORE....
I'm thinking maybe battery is fried and that's why the grey color screen appears and not the usual screen where you see the battery charging...
After reading this thread it's clear that my handset is one of the new ones that have recovery/download modes disabled via the volume+power buttons.
So that pretty much covers it... I hope TMO will not ***** about the files that are on the internal sd that I am unable to access and remove... unless anyone else has any fresh ideals how to gain access to the disk
I think I might have a similar problem.
I accidentally deleted the touchwiz framework so I can't do anything ON the phone. It boots up, and gets me to the lock screen. As soon as I unlock, I am greeted with dozens of unending force closes.
I can get into both download and recovery mode, however, I have not been able to get ADB to recognize the device. I am attempting to push the stock ROM to the internal memory to flash over everything.
I'm not sure what to do to get ADB to work but it's driving me nuts!
Stuck at vibrant? I have a fix
Check out android Dev Section... I figured out how to access download mode or stock recovery mode when you are stuck at the vibrant screen!!!! BACK IN BUSINESS VIBRANT OWNERS!!!
i got the same problem and nothing seems to work
Try this out http://forum.xda-developers.com/showthread.php?t=1103706
Feels like I'm having same issues..
the previous post requires opening the phone and I don't have tools for that..
Here's my issue.
I can't get into Recovery or Download and computer won't see phone to Odin.
I've got drivers installed and AIO Toolbox as well as ADB(which won't work because of computer not seeing phone.
Using the manual option(vol+ vol- power), nothing works.
I've done all the tricks like unplug it then hold vol keys plug it insert battery..
When I do plug in the phone to to even just get a charge in it goes the the battery, but my is is frozen or something. doesn't turn green or have a charging animation. After about a minute or so it was start up and boot loop. I read something about a bad battery? I've got two of them and they seemed fine before..
Before all this I had to Odin and go to stock. I was attempting to get ics back but I was being lazy and trying to do as little as possible..bad idea. I was following slim ics install and flashed cm9 daily, slimics and commons..and now this..
I'm not sure what to do..I usually search around xda or google..10 hours later.. idk..Anyone able to give help please?
:crying:
eduardo_reflex said:
i got the same problem and nothing seems to work
Click to expand...
Click to collapse
... do i even have to say it?
droyd666 said:
Try this out http://forum.xda-developers.com/showthread.php?t=1103706
Click to expand...
Click to collapse
this problem is most likely solved. After 2 years!
mylostlonelysoul said:
Feels like I'm having same issues..
the previous post requires opening the phone and I don't have tools for that..
Here's my issue.
I can't get into Recovery or Download and computer won't see phone to Odin.
I've got drivers installed and AIO Toolbox as well as ADB(which won't work because of computer not seeing phone.
Using the manual option(vol+ vol- power), nothing works.
I've done all the tricks like unplug it then hold vol keys plug it insert battery..
When I do plug in the phone to to even just get a charge in it goes the the battery, but my is is frozen or something. doesn't turn green or have a charging animation. After about a minute or so it was start up and boot loop. I read something about a bad battery? I've got two of them and they seemed fine before..
Before all this I had to Odin and go to stock. I was attempting to get ics back but I was being lazy and trying to do as little as possible..bad idea. I was following slim ics install and flashed cm9 daily, slimics and commons..and now this..
I'm not sure what to do..I usually search around xda or google..10 hours later.. idk..Anyone able to give help please?
:crying:
Click to expand...
Click to collapse
Try asking another question. But I suggest using a USB jig. They usually work. Then odin
Sent from Mount Olympus via Hermes
Did you ever get it fixed man? I literally did the very same to mine a while back and It works like butter as we speak. It is fixable with a mini-usb jig or dongle. You can make your own with about $3 worth of parts from radio shack but I recommend buying one, it will be easier. I for the record made mine simply twisting together the resistors and though it was tough to touch the right pins it did eventually work and get me back into download mode.
Hopefully you already got it fixed though. If not I can help you out.
So, I wanted to update the Rom, so tried to go into recovery mode. Pushed the volume down button instead of up, so got into download mode. Pushed the volume down button to cancel. Then pushed the right combination, but nothing past the Galaxy S2 logo with the warning triangle happened.
Tried to reboot a couple of times, but now the phone is completely dead.
Everytime I turn it on the Galaxy S2 logo appear, and when it dissappear the phone seems to be dead. However if I look closely, the screen is not turned off, it it just black (but turned on), and every 5 seconds or so I can see it "blinking", but it blinks "black" if you could say that, you won't notice it if you don't look careful, or you are in a dark room.
If you triple click the home button you normally "invert" the colours on the screen, and this also works in this case. Instead of it flashing with an almost unnoticable black, it is now white and every 5 seconds the screen turns off very briefly, but then the screen is white again.
To get it to stop doing this I need to remove battery. If I push and hold the power button the phone just restarts with the galaxy s2 logo, and then does the same again.
When I connect the phone to a charger or to a PC (while it's powered down), the battery logo appears for a couple of seconds, and then it enters this "blinking" screen thing again.
When connected to a PC it does not appear as a drive - however it seems like windows detects it, it installs the GT-9100 drivers. Samsung Kies can't connect, it just keeps trying to connect forever, without coming with an error, but it's not connecting.
Hard reset is not working in any of the described ways, whatever I do, if its to get it into recovery mode, download mode, or just trying to turn the damn phone on, it just do the blinking thing.
Is this some sort of a boot loop from hell!!?
sounds strange, can you still get it in download mode without issues?
If you can i would advice to flash back to stock(!!)
or you could try to flash a cf-root to see if thats gets you into recovery format system, data, cache, dalvik and flash the new rom.
but im not sure if that would work, a clean install from stock would be better i believe,
as to why it went this way i have no idea!
Good luck!
If you can get in download mode, flash a stock rom with odin and that should do the trick
yes!
Well, that was odd, thought I had tried that several times, but yes now at least I can get it into download.
Now I used ODIN to flash a file (CF-Root-SGS2_XX_XEO_LPQ-v5.3-CWM5.tar) that I had laying on my PC from back when I was originally rooting my phone. ODIN gave me a "Pass" reply and I got the phone into a bootloader. I quickly wiped everything I could, and at the moment I'm seeing if I can boot the phone normally.
Thanks!!
Well my rom is f***** it won't boot, but atleast I can get it into recovery mode.
Have just installed cyanogen 9 stable + gapps, it is now booting up!
Luckily I backed my phone up with Titanium backup just a couple of hours ago!!!
it's working!
Well that saved my ass. I was so close to throwing my phone out of the window and going online to order a S3...
Now I'm setting up my phone - nice, wanted to try Cyanogen 9 anyway.
Cool.. Always be patient.... Rather than thinking of purchasin a new phone when these kind of situations occur. Keep a usb jig with you
Sent from my GT-I9100G using xda premium
I have a rooted i777 with SHOstock rom, I haven't updated the rom for a few months so I'm not sure which version it is.
The phone was working yesterday and it suddenly got stuck so I tried to reboot it (had to take out the battery because the power button didn't respond) but now each time I try to turn it on it is stuck on a black screen with the logo "Samsung Galaxy SII" and won't progress.
I tried to boot to recovery but it shows a screen saying "CWM-based Recovery v6.0.2.7" but it doesn't go pass the screen to show the recovery menu (it just reboots after being stuck on this screen for about a minute).
I tried to boot to download mode and succeeded, but every time I connect the device to my pc, the pc doesn't recognize it
(I tried re-installing kies, but it didn't help and probably the problem is not with the pc drivers because if I connect my wife's unrooted i777 to the pc it does recognize it).
so now I don't have clue what else to try.
any advice will be appreciated.
Make sure you have Odin v1.85 on your Windows PC. Look in the Windows Add/Remove programs dialog (or Uninstall a Program dialog) to see if you have SAMSUNG USB driver for mobile phones.
Open Odin on the desktop. Next put the phone into download mode by holding down vol + and vol - while plugging in the USB cable.
If Odin recognizes your phone, flash back to stock. I would recommend UCMD8 stock firmware, which you can get from the Download Repository.
don't know what happened to it but now it doesn't even turn on.
it's stopped turning on before I had a chance to try what you suggested.
now even if I connect it to the charger it doesn't show the charging status.
is there any other "force something" I can try?
kokoman said:
is there any other "force something" I can try?
Click to expand...
Click to collapse
Remove the battery and leave it out. Connect the USB cable to your PC. While holding down the vol- button (also try it with both vol- and vol+) but not the power button, plug the USB cable into the phone. The computer will provide the power. If this works, your phone will go into download mode. If not... you have very likely had some kind of hardware failure.
unfortunately it didn't work.
can't get it to download mode.
I'll try to leave the battery out for a longer time and try again.
should I try ordering a JTAG usb and see if it puts it in download mode or
probably my only option is to send it to mobiletechvideos?
I had the same problem, Your battery got too low. Pull your battery and leave it out for a while 15 mins or so. Put the battery back in and connect charger. Let the battery charge for a while without trying to turn on phone. The phone will not turn on with a dead battery even if it is connected to charger.
I just solved a problem that I didn't find any help with, so I thought I would post it here in case somebody else needs help out of this situation, and this is a recent and related thread.
After I pulled the battery of my i777 to test in another phone, without remembering to power my phone off first, it would only hang at the Samsung boot logo (stock UCMD8 ROM, rooted, stock recovery). Normally the Samsung boot screen shows for only about five seconds. Pulling the battery wouldn't get it to boot right. Holding Power to force a reboot didn't solve it. After clearing the cache it would move to the AT&T Rethink Possible screen once, then reboot and then again get hung on the Samsung logo screen. Also my battery was heating up a lot as it was hung.
I could get into both download mode and recovery. I tried reflashing my ROM from the stock file in ODIN since that would save all of my data IF it worked. This still didn't get it to boot past the first logo. Finally doing a factory reset on stock recovery is what solved my problem. I had to re-add my account and reload apps from scratch, etc.
How the problem occurred
So a year or two ago I bought a Jiayu G4A/T/Whatever they're calling it and safely got it here. I've used the stock ROM for a bit but I wanted to get rid of the bloatware that was still on it, so I eventually ended up with a properly rooted phone with a ROM from Jiayu.es (Everything worked, have ClockworkMod as recovery, accessible via Mobileuncle Tools), which was essentially a stock Kitkat rom made to work for the phone. Now I got sick of the ROM and recently saw the new EMUI version on Huawei's P8 Lite, so I figured I'd look around for a tailored ROM running that, and ended up at "jiayu-emui-3-0-stable" from Needrom.
What I did
1. I downloaded a ROM from Needrom with identifier "jiayu-emui-3-0-stable" (I can't post external links)
2. Backed up my important files following a guide from androidcentral titled "[Guide] How to Backup and Restore Apps and Data when installing new ROMs" that I can't link,and did a full backup using CWM
3. Placed the ZIP on my internal SD card, went into recovery, wiped data/cache (not dalvik, since it wasn't described in the instructions, I think this might be a probable cause) and installed the new ROM from ZIP
4. Rebooted the phone and now it's stuck in the boot loop I mentioned.
What the problem is
Bootloops aren't that much of a problem usually, except this one is... I can't get into recovery mode. From there on it'd be cake, since I made the right preparations, but I can't get into it. While connected to my PC it keeps powering on, showing a splash screen from Jiayu.es briefly (which shouldn't be present anymore) and powering off after 10 seconds, only to come back to the splash screen.
What I've tried
I've unplugged it, removed the battery, waited to get a full power cycle and tried to hold my buttons in these combinations: [power button + volume up], [power button + volume down] - but neither work. It just keeps going with the boot loop. I can succesfully power it down, and when I plug it in from there it shows the low battery image. At the moment of seeing that I thought I could connect to it using ADB / Fastboot, but no luck there either. It keeps saying no devices found, and with fastboot it keeps on <waiting for device>.
My questions
What exactly can I do if there is no way for me to get into recovery mode? Are there any alternatives? How can I get my device to be recognized by ADB? Is that even possible? Why is this bootloop any different from others?
Update from the massive Q&A thread:
ZipAddict said:
Is it booting up on its own too after being off? This happened to wifes phone and it turned out the power button was stuck. I took a pencil and hit the power button with the eraser a few times and it worked then. Her case mustve dislogded it. I will keep my fingers crossed for u. If not send me a private message and i will look for an answer tomorrow and get back with u
Click to expand...
Click to collapse
Thank you for the reply!
Yes, it does. I took the battery out and let it lay disassembled for a night, after which I cleaned it a little and re-inserted the battery. With the case back on, nothing happened, so the power button wasn't stuck for sure. When I powered it back on with the power button (no USB attached) it showed the emblem for ~8 seconds and powered off. It then buzzes to show it's powered on again and up comes the splash screen again. Could it be that the ROM was just a rebooting falsehood? Why would it disallow me getting into recovery mode? I really hope there is something that can still force the device into recovery mode / interact with it somehow while in this state.
Oh, I also tried to see if the volume down button was broken but all the contacts seem intact, plus, they worked an hour before I started switching roms.
Hello,
New to the forum and all of this, so please go easy on me.
I have a Samsung Galaxy S9+ (SM-G960F).
On Thursday evening, I went to the device and it was completely dead. It wouldn't turn on and I attempted to do power key/volume down and various other button combinations I found online that would normally boot the device. Obviously, I attempted to charge the phone, but the charging light did not come on yet the phone did warm up slightly as if it was charging. After leaving it plugged in for so long, a 'Downloading... Do Not Turn Target Off' screen appeared. It also states I can restart the phone by holding volume down/power button for seven seconds. However, when I do this the phone just goes dead and doesn't boot up. After plugging in the charger again trying various buttons, I eventually end up back at the same download screen.
I've read about recovery mode, safe mode etc but I am unable to access them using the instructions I've read.
Any help would be appreciated. Ideally I'd like to be able to access my photos/videos/messages on the device and be able to use it again.
Jamfocus said:
Hello,
New to the forum and all of this, so please go easy on me.
I have a Samsung Galaxy S9+ (SM-G960F).
On Thursday evening, I went to the device and it was completely dead. It wouldn't turn on and I attempted to do power key/volume down and various other button combinations I found online that would normally boot the device. Obviously, I attempted to charge the phone, but the charging light did not come on yet the phone did warm up slightly as if it was charging. After leaving it plugged in for so long, a 'Downloading... Do Not Turn Target Off' screen appeared. It also states I can restart the phone by holding volume down/power button for seven seconds. However, when I do this the phone just goes dead and doesn't boot up. After plugging in the charger again trying various buttons, I eventually end up back at the same download screen.
I've read about recovery mode, safe mode etc but I am unable to access them using the instructions I've read.
Any help would be appreciated. Ideally I'd like to be able to access my photos/videos/messages on the device and be able to use it again.
Click to expand...
Click to collapse
-Download odin
-Download firmware for your phone
-unrar firmware file
-open odin
-flash AP , BL , CP , HOME_CSC (HOME_CSC goes on USERDATA) if you haven t formated your phone by mistake your files will be there and your phone working.