I'm looking for the stock ROM for the vodafone 888. The phone won't boot because an update went wrong but I still have access to the recovery menu.
The current ROM version reported in the recovery is:
4.4.220.06.T3.140404.DVT49L.VF.GR
Thank you!
silverThe said:
I'm looking for the stock ROM for the vodafone 888. The phone won't boot because an update went wrong but I still have access to the recovery menu.
The current ROM version reported in the recovery is:
4.4.220.06.T3.140404.DVT49L.VF.GR
Thank you!
Click to expand...
Click to collapse
hi.
i am looking for the stock firmware for this device..anyone has it..? or recovery or custom rom..?
have u find a firmware?
my vodafone 888 does not boot any moore
fixed my phone today and all is well. The name of the phone is actually coolpad 7576u and the firmware i downloaded from http://www.yulong.com/product/produ...productBO.product.id=6504&productBO.menuId=30
the frogram to install this firmware is Coolpad Download Assistant Setup V1.86_140626 (google-it)
steps to install are simple.
1 download firmware
2 unzippit to *.CPB
3 start program
4 point program to the unzipped rom
5 connect phone to pc without battery (you remove the battery)
6 wait until is done
7 ENJOY
Did you install some drivers? Mine doesn't seem to work. I load the rom into Coolpad Download Assistant, I hit some button in Chinese, instinctively, then a bar loads to 100% and another one is at 0%. Stays like this forever nothing happens to the phone. It is in fastboot mode, battery off, plugged in with usb cable, adb drivers installed.
Later edit: I finally got it right. Reinstalled the drivers...
i have the same problem.any idea?
---------- Post added at 09:20 AM ---------- Previous post was at 08:55 AM ----------
i am looking for drivers
Install android sdk - now also integrated into Android studio - it should install google adb drivers automatically. Also give the PC and phone a restart after sdk is installed. Then you should have no problem hooking up the phone and yulong download assistant.
freakaleo said:
fixed my phone today and all is well. The name of the phone is actually coolpad 7576u and the firmware i downloaded from http://www.yulong.com/product/produ...productBO.product.id=6504&productBO.menuId=30
the frogram to install this firmware is Coolpad Download Assistant Setup V1.86_140626 (google-it)
steps to install are simple.
1 download firmware
2 unzippit to *.CPB
3 start program
4 point program to the unzipped rom
5 connect phone to pc without battery (you remove the battery)
6 wait until is done
7 ENJOY
Click to expand...
Click to collapse
100% worked for me. Now My Vodafone 888 is fully working.
Download flash Software from here...
Coolpad Download Assistant Setup V1.88
RO.maniac said:
Install android sdk - now also integrated into Android studio - it should install google adb drivers automatically. Also give the PC and phone a restart after sdk is installed. Then you should have no problem hooking up the phone and yulong download assistant.
Click to expand...
Click to collapse
Hey can you help me? I downloaded android SDK and now it recognizes the phone as an ADB Interface. Although on "Coolpad Download Assistant" it goes through the first 10% and then just skips to the end and a weird smile shows up with some chinese stuff.
What am I doing wrong? (I am connecting the phone to the pc withough battery it shows "Fastboot mode TA" on the screen) I'm using my country's rom (4.4.230.33.T3.140715.7576U.vf_pt) Tried with YGDP doesn't work as well...
Edit I'm using windows 8.1 tried on Windows 7 and it goes all the way up to 55%
firmware file needed
I have been searching around sites but unlucky, i cannot find firmware file for vodafone 888 smart 4 / coolpad 7576u firmware file. original site redirects to main page only by the above links. Please help me.
HI where is firmwere¿¿??
xbekoolx said:
I have been searching around sites but unlucky, i cannot find firmware file for vodafone 888 smart 4 / coolpad 7576u firmware file. original site redirects to main page only by the above links. Please help me.
Click to expand...
Click to collapse
gold_mobile said:
HI where is firmwere¿¿??
Click to expand...
Click to collapse
Here you have a .zip file containing the RO version of the stock 4.4.2 ROM for Vodafone 888. You can change the language afterwards, it's just a matter of bloatware apps for each country.
drive: https://goo.gl/o79jHC
vodafone 888
RO.maniac said:
Here you have a .zip file containing the RO version of the stock 4.4.2 ROM for Vodafone 888. You can change the language afterwards, it's just a matter of the bloatware apps that comes with in each country.
https://www.dropbox.com/s/ajp6sbie8eeqn8a/4.4.230.33.T3.140715.7576U.vf_ro.CPB.zip?dl=0
Click to expand...
Click to collapse
Thank you work perfect ! I flash phone with Coolpad Download Assistant
http://forum.xda-developers.com/android/help/stock-rom-vodafone-888-t3002958:)
Vodafone 888
Since I am a new member I can't post links so if anyone wants the greek rom just message me
Not really sure what the error is, but i guess it`s something wrong with the drivers.
After 3% i get the following (see the attached pic)
I used Android_adb-USB_UnifL_Driver_v1.17
from here: http://leshcatlabs.net/downloads_usb_unifl/
tintome said:
Not really sure what the error is, but i guess it`s something wrong with the drivers.
After 3% i get the following (see the attached pic)
I used Android_adb-USB_UnifL_Driver_v1.17
from here: http://leshcatlabs.net/downloads_usb_unifl/
Click to expand...
Click to collapse
I had this problem but at some higher percentage. I just kept retrying and it finally worked. I don't remember if I messed with the drivers anymore once it started. You should uninstall every android/google driver you have, reboot, install again.
Device manager looks fine tough, bootloader interface.
///jos Gâdea & Co///
RO.maniac said:
Did you install some drivers? Mine doesn't seem to work. I load the rom into Coolpad Download Assistant, I hit some button in Chinese, instinctively, then a bar loads to 100% and another one is at 0%. Stays like this forever nothing happens to the phone. It is in fastboot mode, battery off, plugged in with usb cable, adb drivers installed.
Later edit: I finally got it right. Reinstalled the drivers...
Click to expand...
Click to collapse
can u provide a link with the drivers for Vodafone 888? multumesc
Custom rom vodafone 888 ?
domino_xxi said:
can u provide a link with the drivers for Vodafone 888? multumesc
Click to expand...
Click to collapse
uninstall every google/android driver you have, then install android studio, it bundles the drivers, easy. or you can search for some fastboot/adb drivers little package.
I no longer have this phone. sorry for being late
Lefter1s said:
Since I am a new member I can't post links so if anyone wants the greek rom just message me
Click to expand...
Click to collapse
hi can you send me the greek rom please?
Related
Hi all,
I have Gionee elife s5.5 and it had english rom (android 4.2.2) with google play installed. The problem was it kept freezing a couple of times a day, so I tried to reinstall the only official rom I could find (CBT5701A01_A_T2898) with flash tool. After the installation, it got stuck in the boot loop.
I tried:
- entering the recovery mode and cleaning the cache
- entering the recovery mode and factory reset/wipe
- reinstall rom with flash tool with update option
- reinstall rom with flash tool with download option
- reinstall rom with flash tool with download and format option
- reinstall rom with flash tool v3.1344.0.212 and v5.1352.01
So far, no luck. The only answer I can think of is that this rom is not for my phone version. Anybody has any idea what can I do? Or does anybody have some other rom I could try to install?
Thanks in advance.
tchs said:
Hi all,
I have Gionee elife s5.5 and it had english rom (android 4.2.2) with google play installed. The problem was it kept freezing a couple of times a day, so I tried to reinstall the only official rom I could find (CBT5701A01_A_T2898) with flash tool. After the installation, it got stuck in the boot loop.
I tried:
- entering the recovery mode and cleaning the cache
- entering the recovery mode and factory reset/wipe
- reinstall rom with flash tool with update option
- reinstall rom with flash tool with download option
- reinstall rom with flash tool with download and format option
- reinstall rom with flash tool v3.1344.0.212 and v5.1352.01
So far, no luck. The only answer I can think of is that this rom is not for my phone version. Anybody has any idea what can I do? Or does anybody have some other rom I could try to install?
Thanks in advance.
Click to expand...
Click to collapse
Where did you get the phone? Try looking here, translate it using Google.
http://www.mgyun.com/
I bought it on ebay from China. Thanks for the link but no luck. I've downloaded the new rom and the romaster program (I'm guessing I should use it for the installation) but the program is not detecting that the phone is connected via usb. Same thing with vroot.
Since this rom is in another format, I was thinking maybe I could install it via adb option in recovery mode but I'm getting 'device not found' message when I try to start adb shell.
tchs said:
I bought it on ebay from China. Thanks for the link but no luck. I've downloaded the new rom and the romaster program (I'm guessing I should use it for the installation) but the program is not detecting that the phone is connected via usb. Same thing with vroot.
Since this rom is in another format, I was thinking maybe I could install it via adb option in recovery mode but I'm getting 'device not found' message when I try to start adb shell.
Click to expand...
Click to collapse
Have you installed the drivers for the phone?http://gionee.co.in/portfolio/elife-s5-5/#t4
---------- Post added at 03:12 AM ---------- Previous post was at 02:30 AM ----------
Try here, you need to register.
http://www.yougerom.com/bbs/forum.php?mod=viewthread&tid=265
Yes, I installed usb and phone drivers. I also installed adb driver (at least adb driver installer says it is installed as android composite adb interface) and yet when I try adb shell, deamon starts ok but I keep getting the message that the device is not found.
The rom from your link is the same one I already have, but thanks anyway.
All this is very frustrating. Seems like everywhere I go, I hit the wall:
- if the phone has sdcard I could try install rom from there, but it doesn't
- if adb connection works I could try that, but it doesn't
- if romaster detects the phone I could try install it from there, but it doesn't
- sp flash tool is working but I could find only one rom version and it's not working
You did the brushing before installing the flash've used Flashtool?
Have you looked in setting pc, peripherals, if you have something in conflict, if you do not have the yellow exclamation mark?
Also I have just bought this phone, by Liaow, who did the root and installed the Playstore. Now my phone is still stuck in Hong Kong and I do not know when it will arrive in Italy.
How did you like the phone, the battery life, becomes very hot since the minimum thickness?
I don't know what do you mean by 'brushing' so the answer is probably not?
Everything looks ok in pc's control panel, no conflicts or unrecognized devices etc. It's win7 64bit.
I was thinking about buying it via Liaow but in the end I used ebay. It took 3 weeks to arrive, and I paid for DHL express delivery (!) Isn't EU wonderful thing...
I really liked the phone (in the brief time it was working). Display is great, it's fast and the battery would last for a day without a problem. The build is very solid. I wasn't playing any games on it or use any apps that would use cpu extensively, but in normal operational time I didn't notice any significant heating. I even liked the Amigo skin. It has some nice features and was working very fast. The only problem was it kept freezing couple of times a day, usually after long times of inactivity which led me to believe it has some sort of problem with power saving functions in android (or amigo). Oh one other thing: it doesn't have notification led. I miss that.
If you don't get your phone, I know where you can get one very, very cheap. It's stuck in the boot loop, but still...
Brushing think it is to do a full wipe before doing the flash with Flashtool.
When you receive your phone, you've got an update OTA of 98 mb?
Thank you but the phone I have already paid and are waiting for his arrival.
I hope we put less than three weeks since I also took DHL.
In Italy we have a beautiful community where there are developers who work here in Xda, who are fond of Chinese mobile phones and in particular there is a person who develops rom alternatives.
So I guess I would be able to help me if I had the same problem, but I hope I do not have any problems.
You say you had blocks of hibernation in power saving mode enabled, then maybe in normal mode just fine.
I do not usually use the mode energy in any phone I've had.
I prefer to charge the battery when needed.
First I tried only update, after that I tried full wipe.
I did try to disable every power saving mode I could find, but the phone still kept freezing. Although, there are some options that are useful, like limiting cpu for more energy and lower temperature.
I didn't get OTA update, but the seller told me that they had to open the box to install english rom version with google play. Maybe they also installed this update.
got another elife threat here http://forum.xda-developers.com/showthread.php?t=2699708
Here's the quick update: after I manually edited adb_usb.ini file, adb sideload works now. But...none of the rom's I have can be installed with adb (I get 'installation failed' message after transfer).
So, what I need is:
- rom that can be installed via adb sideload
or
- rom that can be installed via flashtool with scatter file (after extensive search of the web, the only rom I could find on several places is the one made 11-03-2014 and this one is not working for me)
Any help would be greatly appreciated.
tchs said:
Here's the quick update: after I manually edited adb_usb.ini file, adb sideload works now. But...none of the rom's I have can be installed with adb (I get 'installation failed' message after transfer).
So, what I need is:
- rom that can be installed via adb sideload
or
- rom that can be installed via flashtool with scatter file (after extensive search of the web, the only rom I could find on several places is the one made 11-03-2014 and this one is not working for me)
Any help would be greatly appreciated.
Click to expand...
Click to collapse
http://bbs.amigo.cn/thread-758-1-1.html
XPAction said:
http://bbs.amigo.cn/thread-758-1-1.html
Click to expand...
Click to collapse
Thanks but I already tried that. This only works with Romaster app and it doesn't recognize my phone being connected while on boot loop or recovery mode.
Even my phone is stuck on boot, can anyone help me
Tired of searching everywhere cant find it anywhere, can anyone please share a link from where I can download rom for my gionee elife S5.5 Indian version, my phone was working fine until I installed beats audio It asked to reboot and the then it never rebooted, stuck on gionee boot animation, I also flashed the Chinese rom but it doesn't support, phone was booting up but the rom is too lagging and unstable. I don't want to go to the service center cause my phone is rooted and warranty will be voided, I just bought it two days back. Is CWM available for this phone cause I couldn't find that too, I'd be more than grateful If anyone can help me out I just need the rom file (Indian version), thanks a million !!!!
i also tried to install beat audios on my gionee s5.5 ... and now it is not statting my phone get stucks at boot animation logo "gionee smatyphone"
Here are some good news people: needrom.com site finally released new rom version and it can be installed via adb sideload. It is CH/EN version and even when you switch it to English, some things still stay in Chinese but hey - at least it's not in boot loop anymore and now you have more options for rom installation.
Thanks dev, was so sick of this phone and its features, especially free mobile heater(owen) + worst sound ever + lots of lags, even flappy bird lags on this phone though I had optimised the cpu performance using set cpu to its max by creating a profile to play flappy bird, mediatek chipset sucks happy after entering the snapdragon world, just bought M8 yesterday and believe me this is the best phone till date though the ram is 2gb the processor is a the beast and there's no comparison to it and when it comes to the sound no one can beat htc, the looks it feels so ****n premium, the touch is like butter smooth, loving it!! Thanks
Sent from my HTC One_M8 using XDA Free mobile app
how to install rom from needrom via adb shell.?? can anyone explain?
FirmwareFile
https://firmwarefile.com/gionee-s5-5 , i've used T8881 version , and it was good
Unbrick Oppo R5
Since oppo forums support is minimal and a lot of Oppo R5/ R5s owners are facing difficulties flashing new rom and since Oppo is unbrickable here are a guide as posted to oppo forum members by the member Ricky.
I had clear instructions not to post this tool anywhere BUT THEY DON’T SUPPORT ANY DEVICE and I have to break my promise as they broke any kind of support.
This community (XDA) is to help all members
The tool works with windows 10 and not only with windows 7 as they mention in their instructions
Packages you have to download first
1- Firmware ColorOS https://www.partage-facile.com/LM6Y85FF7Z/r8106ex_11_a.16_150806.tar.bz2.html
File Name: R8106EX_11_A.16_150806.tar.bz2
Size: 1.4GB
MD5: F85ED63BA637B559976D9BFF0AED0187
2- Instructions:
https://drive.google.com/file/d/0B3AWkNVCRSNVZGNRUE1rQW5YOFk/view?sid=
3- Driver : http://en.oppo.com/downloads/firmware/driverForFind5.rar
Mirror for driver http://www109.zippyshare.com/v/MEMiPlOv/file.html
Attention
a-Unbrick tool will wipe all data on your device including photos and music etc, if do you want to reserve your data please make o back up on your PC
b- After unbrick the first time power up take around 5-15 minutes
c- The most important things are to install the driver. For windows 10 you must enable unsigned signature verification through windows advanced settings (google it) prior driver installation.
d- In order to shut phone completely hold the power button for 8 -10 secs
How to use the tool
I tried to use the tool and the files you provided to revive my Oppo R5, but the layout of the tool which you provided is different from the one in the picture (you gave in the links). It is also in foreign characters so difficult to choose with option to tick.
In fact, the version that came with you package does not have as many option as the one in the picture. My confusion actually starts from when the program starts. There is a drop down menu to chose from a long list of 14005 to 15065. Which one do I choose for Oppo R5?
As for the qualcomm port, the device manager identified my phone on port 9006, whereas the picture shows 9008.
Please help me. I really need to get this phone to work. The phone would not do any thing is the buttons are pressed individually or in combination, other than being detected by the computer and enumerated in the device manager.
Many thanks in advance for your help.
amadoro said:
I tried to use the tool and the files you provided to revive my Oppo R5, but the layout of the tool which you provided is different from the one in the picture (you gave in the links). It is also in foreign characters so difficult to choose with option to tick.
In fact, the version that came with you package does not have as many option as the one in the picture. My confusion actually starts from when the program starts. There is a drop down menu to chose from a long list of 14005 to 15065. Which one do I choose for Oppo R5?
As for the qualcomm port, the device manager identified my phone on port 9006, whereas the picture shows 9008.
Please help me. I really need to get this phone to work. The phone would not do any thing is the buttons are pressed individually or in combination, other than being detected by the computer and enumerated in the device manager.
Many thanks in advance for your help.
Click to expand...
Click to collapse
For R5 use 14016.
mermigas said:
For R5 use 14016.
Click to expand...
Click to collapse
Thank you for your reply. I tried to use the tool again, but there is not option for 14016. The full list is here: 14005, 14006, 14023, 14037, 14039, 14040, 14041, 14042, 14043, 14045, 14046, 14047, 14050, 14051, 14052, 14061, 14062, 14065, 14068, 140083, 14085, 14097, 14098, 15005, 15005_4G, 15006, 1500_4G, 15007, 15007_4G, 15011, 15012, 15013, 15018, 15057, 15061, 15065.
The flash tool that I am using is V1.5. Is is possible that I am using a wrong version for what I need to do?
Many thanks for your attention.
amadoro said:
Thank you for your reply. I tried to use the tool again, but there is not option for 14016. The full list is here: 14005, 14006, 14023, 14037, 14039, 14040, 14041, 14042, 14043, 14045, 14046, 14047, 14050, 14051, 14052, 14061, 14062, 14065, 14068, 140083, 14085, 14097, 14098, 15005, 15005_4G, 15006, 1500_4G, 15007, 15007_4G, 15011, 15012, 15013, 15018, 15057, 15061, 15065.
The flash tool that I am using is V1.5. Is is possible that I am using a wrong version for what I need to do?
Many thanks for your attention.
Click to expand...
Click to collapse
Sorry mistyped
14061
Also there is an English Version for the flashing tool here
https://forum.xda-developers.com/r7-plus/help/oppo-r7plusm-msm-tool-t3313759.
Just download it and copy to the folder that there is the Chinese tool
For me the Chinese version works fine
Also there is a same guide here
http://community.oppo.com/en/forum.php?mod=viewthread&tid=51497&extra=
mermigas said:
Sorry mistyped
14061
Also there is an English Version for the flashing tool here
https://forum.xda-developers.com/r7-plus/help/oppo-r7plusm-msm-tool-t3313759.
Just download it and copy to the folder that there is the Chinese tool
For me the Chinese version works fine
Also there is a same guide here
http://community.oppo.com/en/forum.php?mod=viewthread&tid=51497&extra=
Click to expand...
Click to collapse
Thank you so much. it worked. Not my Oppo r5 is back alive.
Where is the download?
Is it normal that when I hit the download link there appear aliexpress??
I thought I had bricked my R5 but while trying to follow this guide it wasn't showing up in the "Ports" section of the Device Manager. I found that my phone still had fastboot, so I used it to install latest TWRP and then the repair rom. And now my phone is finally back to working condition! I hadn't modified in any way my phone and one day it got stuck at the logo. Anyway, thanks for the guide Mermigas!
anyone mirror pls
mega
[email protected] said:
anyone mirror pls
Click to expand...
Click to collapse
[dead link]
If it asks for a key leave it blank
Kushracer said:
https://mega.nz/#F!q8YFEJyB
If it asks for a key leave it blank
Click to expand...
Click to collapse
No asking for decryption key
mirror
Uploading here: R5S Unbrick Tools
Please help
After i have done all those instructions: my phone was completely dead(no more display and can't use any buttons).
Please what should i do for revive that.
Link Broken
cpuld you re-load the link of Color Os firmware please?
Its not valid now =(
Number for R5S?
Hi, I tried the 14061 for my OPPO R5S. Unfortunately it did not work. Now the phone is not starting.. help? Should I use another number?
Code:
**** DISCLAIMER ****
This post is an EXPERT-LEVEL Post.
I am NOT RESPONSIBLE for what you do to your device.
Please not that I am still working on a solution to this brick.
Hello XDA-Developers,
I recently got my hands on a Meizu M3 note and, of course, wanted the newest - nougat - firmware on it. It seems I accidently flashed a incompatible (or currupted) Update (flashed an A Firmware on a G version phone). Sadly it broke down and showed only vertical stripes on it's display.
Image here: https://ibb.co/cpGunm
After some hours research I found some information on how to reflash the M3 note via SP Flash Tool here and here. Since the first tutorial is for the M3 and M3s and the second tutorial is for the M model of the device (I've got the L model) there are some changes needed for it to somehow magically work.
I exchanged files provided (such as preloader.bin, lk.bin etc) with the matching ones from the latest Official Global Firmware from Meizu. Just extracted them out of the update.zip. (Don't forget to select the Authentication File!)
Image here: https://ibb.co/k3zYDR
Short flashing tutorial: make sure your device is turned off and disconneced then click "Download" and connect your device via USB. Don't worry if it now shows an error like "Download DA Failed", just dismiss the error and click "Download" again. It should flash the device now.
Sadly it is not possible to flash the boot.img provided in the latest official update.zip from Meizu (you'll get an security mismatch error). BUT the boot-verified.img provided by the chinese archive is flashable and is accepted by the device. The device is now in a bootloop, fastboot is accessible via holding Vol - and Power, but no recovery access via Vol+ and Power
The files seem to be repaired now but the display still shows these stripes - I think the firmware actually fried something on the display chipset. I bought a replacement screen and then will update this thread as soon as possible. If you have any Ideas of how to unbrick the device feel free to discuss.
Update 18.11.2017
Thanks to @ncristian !
I did as he suggested, downloaded and flashed the files from the russian forum here (if you do not speak russian and want to get straight to the point: Direct Download Link)
I still have the stripes on my screen but the device booted up successfully and got recognized again by my computer! While booting up I could see the stripes changing their color slightly as the bootanimation of flyme was playing. I guess I will have to replace the screen to make the display error go away... I will update this post as soon as I did so
Update 10.11.2018
Sadly I never actually exchanged the screen, I'm running a Pro 7 Plus as a daily driver now and I'm loving it
Update 19.05.2019
I have attached the boot-verified.img as someone requested it
I had the same problem and I solved thanks to this: https://4pda.ru/forum/index.php?showtopic=739028&st=24480#entry65580668 and Google Translate; I downloaded the .zip, installed drivers, launched the flash tool and flashed files contained in the folder L691H (Remember to install drivers and disable antivirus or it will not work). Then I downloaded FlyMe 6.1.0.0G, went into recovery with vol up + power, copied the update.zip into the device "Recovery" and flashed it; the only problem I had is that the phone charged but he didn't recognize the battery level; by reflashing the files contained in the 4pda .zip, the battery level went up (obviously, after leaving the phone charging for about an hour).
Someone please help my meizu m3 note bricked after flashing flyme 7.8 beta.
Rajdas26 said:
Someone please help my meizu m3 note bricked after flashing flyme 7.8 beta.
Click to expand...
Click to collapse
Try reflashing via the original recovery, that might be your easiest solution. If that doesn't work you might try your luck with something like SP flash tool
Hey. Uhmm i know it's an olld post but i'm hopeless now. I need the boot-verified img you have. i can't find it anywhere. can you send it to my gmail ?? [email protected]
shawn_mendes said:
Hey. Uhmm i know it's an olld post but i'm hopeless now. I need the boot-verified img you have. i can't find it anywhere. can you send it to my gmail ?? [email protected]
Click to expand...
Click to collapse
I have attached the file to the first post. Good thing I never delete anything :angel:
m3shat said:
I have attached the file to the first post. Good thing I never delete anything :angel:
Click to expand...
Click to collapse
First of all, thank you mate I successfully downloaded the boot verified. But still it didn't turned on. Just no power but recognized by the sp tool. I'm starting to think that downloaded again the wrong firmware. I also found out that their are two main board(or whatever is that). So this global firmware can be flashed in the both L and M series. I'm wondering what firmware you used to flash. Again, thank you in advance ^_^
l got same problem .. (because I'm not read careful )l tired to flash using many firmware or using boot verified .. i tired that for 2 Days.. So l give up.. take my device to profesional service . and solved. solved with Emmc repair ..
my device is L681H.
SORRY WAS INACTIVE FOR SOMETIME... NOW IM BACK YOU CAN ASK AGAIN...
ALL CHIPSETS UNBRICKING METHOD HAS BEEN POSTED
Hi you may ask me anything related to android and I promise to answer within 24 hours and m reply will definitely work for you.
*****************************************************
SPECIALIST IN ROOTING, DEVELOPMENT, HACKING, SECURITY BYPASS, RECOVERY, FLASHING, CUSTOM ROM'S
*****************************************************
SEE YOU SOON
*****************************************************
•NOT RESPONSIBLE FOR ANY DAMAGE CAUSED TO YOUR DEVICE•
LG Aristo v10g Metropcs
How do i start configuring this phone without a google account?
A friend who was using it gave me this phone but forgot the boot password and the google account was not of him. So, now, we can´t use the phone.
Mephis96 said:
How do i start configuring this phone without a google account?
A friend who was using it gave me this phone but forgot the boot password and the google account was not of him. So, now, we can´t use the phone.
Click to expand...
Click to collapse
You mean to say that the phone is in frp mode?
(Factory reset protection)
Yes
FRP..... thanks, id did not know what it means.
Yes, it is in FRP
Mephis96 said:
FRP..... thanks, id did not know what it means.
Yes, it is in FRP
Click to expand...
Click to collapse
Can you please tell me the phone model and it's info.
LG Aristo v10g from Metropcs
x.ak**** said:
Can you please tell me the phone model and it's info.
Click to expand...
Click to collapse
Ita LGMS210 v10g.
What's more do you want me to send? I dont know which information do you need?
[PC] HOW TO CURE A BRICKED M-TEK DEVICE!!
///////////////////////////////////////////////////////////////////////////////////////////
• Download and Install the Android USB drivers for your device that I have mentioned below.
• Power Off your device and remove the battery (only if it's removable)
• Download the stock ROM or the Custom ROM on your PC that you want to flash. (GIVEN BELOW)
• Download and extract SPFT (Smart Phone Flash Tool) on your PC, you will be able to see the files shown in the picture below. (Pic 1.1)
• Open Flash tool.exe (Pic 1.2)
• Once SPFT is launched tap on Download tab. (Pic 1.3)
• In download tab click on Scatter-Loading button. (Pic 1.4)
• Now locate the Scatter File that you will find in the Stock ROM folder that you downloaded in step 3. (Pic 1.5)
• Click on Download button to start the flashing process.(Pic 1.6)
• After finishing a success message will appear. (Pic 1.7)
///////////////////////////////////////////////////////////////////////////////////////////
Downloads:-
https://androiddatahost.com/b9cyw (DRIVERS)
https://spflashtool.com/download/SP_Flash_Tool_v5.1744_Win.zip (SPFT)
https://www.needrom.com/download/lenovo-s850/ (ROM FOR LENOVO S850, REGISTRATION NEEDED ON WEBSITE TO DOWNLOAD THE ROM)
///////////////////////////////////////////////////////////////////////////////////////////
Mephis96 said:
Ita LGMS210 v10g.
What's more do you want me to send? I dont know which information do you need?
Click to expand...
Click to collapse
I was working on another project that you can see below give me 1 hour I'll get back to you ASAP.
Best tool like SetCPU for controlling CPU with profiles?
SetCPU doesn't allow core control though
Mephis96 said:
Ita LGMS210 v10g.
What's more do you want me to send? I dont know which information do you need?
Click to expand...
Click to collapse
How to BYPASS FRP LOCK!
Test conducted on Virtual Machine on my PC
****************************************************************
I am not responsible for any damage you may cause to your device!
****************************************************************
****************************************************************
Never wanted to upload it but did it because I aim at helping people.
****************************************************************
Google FRP (factory reset protection) is aimed at making a stolen phone less valuable.
We usually keep our phones locked with a password or pattern but once its stolen it is easy to erase the data (via Hard Reset) and reuse the phone. With Google FRP in place, whenever the phone is formatted using hardware keys it will ask for the last synced google account details before proceeding further.
///////////////////////////////////////////////////////////////////////////////////////////
Until now, everytime some sort of hack comes out to bypass this screen and then its patched with a security update very soon. Same is the case with LG Aristo. There is a working solution as of now but it may not last long. Let’s see how to get this working –
///////////////////////////////////////////////////////////////////////////////////////////
How to Bypass LG Aristo Google Account –
This process is lengthy, but it’s a sure shot method and works every time.
We need 2 apps to complete this bypass process. They are Shortcut Master Lite and Sidebar Lite. Download the zip file from below link.
DOWNLOAD
>Extract the zip file and transfer the apk files to a micro sd card. Install the SD card in your LG Aristo before proceeding further.
///////////////////////////////////////////////////////////////////////////////////////////
Mephis96 said:
Ita LGMS210 v10g.
What's more do you want me to send? I dont know which information do you need?
Click to expand...
Click to collapse
Done
Drop a like on all my replies so I can stay encouraged and help you further.
YeshYyyK said:
Best tool like SetCPU for controlling CPU with profiles?
SetCPU doesn't allow core control though
Click to expand...
Click to collapse
You may use Kernel Manager it's super useful and will do what you're asking for!
Hi ! Could you help me with my problem ?? https://forum.xda-developers.com/search.php?searchid=446201503
No one seems to be able to help me... thanks a lot!!!!
antoflos said:
Hi ! Could you help me with my problem ?? https://forum.xda-developers.com/search.php?searchid=446201503
No one seems to be able to help me... thanks a lot!!!!
Click to expand...
Click to collapse
I will definitely help you just give me one hour but can you post the following info:
Model Number:
Exact Problem:
How that problem occured:
Model Number: SM-G935F / Galaxy S7 edge
Exact Problem : I can't go back to the dock ROM
How that problem occured : Last week, I wanted to try to change my phone a SM-G935F on a custom rom " Minotaurus Oreo V10". I did it successfuly but didn't like it so much so I decided to go back to stock Rom.
I used Odin and a stock ROM for that but I think I made a big mistake by not wiping with TWRP before flashing with Odin.
It resulted that my phone was stocked on the S7 edge logo. Luckly I can go on download mode so it's not hard bricked but Odin failed on every flash I've tried. It stoped at the step "config.msi"
To flash I used this dock Rom : SM-G935F_1_20161201150115_pbdym44h2s_fac
x.ak**** said:
I will definitely help you just give me one hour but can you post the following info:
Model Number:
Exact Problem:
How that problem occured:
Click to expand...
Click to collapse
Hey man this quite difficult and i need to install this phone's firmware on my VIRTUAL Machine, basically I request you to wait for the time being so I can save your phone.
Drop a like on all my comments above to encourage me.
Huawei P10+ Firmware on Huawei P10 - by accident
Hi:
On my P10, I used Firmwarefinder for Huawei to find the firmware (Oreo with EMUI 8) and after verifying, I downloaded and upgraded the P10 to new firmware. After reboot, the dpi is seemed changed (as picture attached) and when I went to check it on about phone, it says Model is VKY (which is Huawei P10+) - picture attached.
Is there a way to rollback and install the correct firmware on this phone somehow?
antoflos said:
Model Number: SM-G935F / Galaxy S7 edge
Exact Problem : I can't go back to the dock ROM
How that problem occured : Last week, I wanted to try to change my phone a SM-G935F on a custom rom " Minotaurus Oreo V10". I did it successfuly but didn't like it so much so I decided to go back to stock Rom.
I used Odin and a stock ROM for that but I think I made a big mistake by not wiping with TWRP before flashing with Odin.
Click to expand...
Click to collapse
***********************************************************************************
I AM NOT RESPONSIBLE FOR ANY FURTHER DAMAGE THAT MAY BE CAUSED TO YOUR DEVICE...(UNLIKELY TO HAPPEN)
***********************************************************************************
For being able to make the downgrade operation you will have to use a Windows based computer on which you will then install Odin (an official program developed by Samsung and used on update types of operations).
***********************************************************************************
Download Odin on your computer; afterwards install the program by following on screen prompts.
The Samsung Galaxy S7 Edge USB drivers must be installed on your PC too – use Samsung KIES in that respect.
Download the stock / official Android OS for your S7 Edge – from SamMobile or from Samsung’s official website.
Power off your device and reboot into download mode: press and hold the Power, Volume Down and Home buttons for a few moments; then connect your phone with your computer with the help of the USB cable.
After making sure that Odin has recognized your device (the “added” message must be displayed and the ID:COM field should be turned yellow or blue) from the program select the PA option.
Load the firmware file; don’t select the Re Partition and Auto Reboot options; click on Start when done.
Wait while your SGS7 Edge is being updated; when done, remove the USB cord and reboot your phone.
For further info related to the update process reply to my thread
LIKE ALL MY COMMENTS TO ENCOURAGE ME TO HELP YOU.
xironimoh said:
Hi:
On my P10, I used Firmwarefinder for Huawei to find the firmware (Oreo with EMUI 8) and after verifying, I downloaded and upgraded the P10 to new firmware. After reboot, the dpi is seemed changed (as picture attached) and when I went to check it on about phone, it says Model is VKY (which is Huawei P10+) - picture attached.
Is there a way to rollback and install the correct firmware on this phone somehow?
Click to expand...
Click to collapse
No pictures attached!! and yes you can roll back to the stock ROM or even customize the DPI according to your phone [ROOT REQUIRED]
Let me know which one you prefer?
Also like all my comments above to encourage me to help you even faster.
Im try to convert cn to global but my phone gate this arror
negima100 said:
Im try to convert cn to global but my phone gate this arror View attachment 5327565
Click to expand...
Click to collapse
Did you unlock bootloader first, before flashing global fw?
dEFLASH said:
Did you unlock bootloader first, before flashing global fw?
Click to expand...
Click to collapse
No i just use rescue and smart application from motorola web. After i download firmware on application and flash i think can solve my problem on account problem but i got new problem my devices stuck in edl mode. And use another solution use QFIL application but i got thats arror pop.
Sorry my English so bad
negima100 said:
No i just use rescue and smart application from motorola web. After i download firmware on application and flash i think can solve my problem on account problem but i got new problem my devices stuck in edl mode. And use another solution use QFIL application but i got thats arror pop.
Sorry my English so bad
Click to expand...
Click to collapse
Still having the brick phone?
dEFLASH said:
Still having the brick phone?
Click to expand...
Click to collapse
No im send back to claim warranty
dEFLASH said:
Still having the brick phone?
Click to expand...
Click to collapse
Hello,
I´m having exactly the same issue. I tried QFIL to fix it but its giving me errors and I cannot flash it anyhow.
I also have Chinese ROM available: https://meta.box.lenovo.com/v/link/view/b7dd980e0e874b58b2a6d683ad63adac
Problem is that phone is stuck in Download mode and its not possible to turn it off or switch the mode. It can still communicate over COM port within Download mode.
Bootloader was locked.
Is there any way how to get phone from this state?
Ideally I need Global ROM there, but getting it into original state with Chinese ROM would help as well.
Shadow27Jirka said:
Hello,
I´m having exactly the same issue. I tried QFIL to fix it but its giving me errors and I cannot flash it anyhow.
I also have Chinese ROM available: https://meta.box.lenovo.com/v/link/view/b7dd980e0e874b58b2a6d683ad63adac
Problem is that phone is stuck in Download mode and its not possible to turn it off or switch the mode. It can still communicate over COM port within Download mode.
Bootloader was locked.
Is there any way how to get phone from this state?
Ideally I need Global ROM there, but getting it into original state with Chinese ROM would help as well.
Click to expand...
Click to collapse
EDIT:
I´ve fixed it! Heres how to:
Download Chinese ROM from link above
Open Lenovo Smart and Rescue assistant and let it download Lenovo L70081 ROM
Open folder with downloaded ROM from Lenovo Smart and Rescue assistant - you should see bunch of extracted ROM files
Delete all files from that ROM folder
Extract Chinese ROM to Lenovo ROM folder
Run standard Rescue process in Lenovo Smart and Rescue assistant
After this, device will have Chinese ROM and will be booted in FastBoot mode.
Problem is that it doesnt want to boot to OS
EDIT 2:
I´ve also fixed booting problem. Now it will load Chinese OS without any troubles:
Open QFIL
Select Meta Build
Select Programmer path as "prog_firehose_ddr.elf" from extracted Chinese ROM files
Load Content.xml from Chinese ROM files ("contents.xml")
Press Download
Switch phone to Download mode (press and hold all volume and power buttons for a while and the plug a cable to side USB port)
Download will start automatically and it´ll flash whole OS
If step 5 will not be enabled, use step 6 and press Download right after phone is detected by QFIL
Shadow27Jirka said:
EDIT:
I´ve fixed it! Heres how to:
Download Chinese ROM from link above
Open Lenovo Smart and Rescue assistant and let it download Lenovo L70081 ROM
Open folder with downloaded ROM from Lenovo Smart and Rescue assistant - you should see bunch of extracted ROM files
Delete all files from that ROM folder
Extract Chinese ROM to Lenovo ROM folder
Run standard Rescue process in Lenovo Smart and Rescue assistant
After this, device will have Chinese ROM and will be booted in FastBoot mode.
Problem is that it doesnt want to boot to OS
EDIT 2:
I´ve also fixed booting problem. Now it will load Chinese OS without any troubles:
Open QFIL
Select Meta Build
Select Programmer path as "prog_firehose_ddr.elf" from extracted Chinese ROM files
Load Content.xml from Chinese ROM files ("contents.xml")
Press Download
Switch phone to Download mode (press and hold all volume and power buttons for a while and the plug a cable to side USB port)
Download will start automatically and it´ll flash whole OS
If step 5 will not be enabled, use step 6 and press Download right after phone is detected by QFIL
Click to expand...
Click to collapse
Do we do the first process using Lenovo rescue or qfil? Or a combo of both?
TemperedUncle69 said:
Do we do the first process using Lenovo rescue or qfil? Or a combo of both?
Click to expand...
Click to collapse
First part is with Lenovo rescue. Second was with QFIL. But I think first should work with QFIL as well, just didnt try it...
Shadow27Jirka said:
First part is with Lenovo rescue. Second was with QFIL. But I think first should work with QFIL as well, just didnt try it...
Click to expand...
Click to collapse
Thank you. I will try it today.
TemperedUncle69 said:
Thank you. I will try it today.
Click to expand...
Click to collapse
Okay from a non booting phone... Used your first method of replacing global rom with Chinese ROM in rescue app... Got it to go into bootloader afterwards. Yay...
Now I tried using gfil and nothing...it keeps failing.
TemperedUncle69 said:
Okay from a non booting phone... Used your first method of replacing global rom with Chinese ROM in rescue app... Got it to go into bootloader afterwards. Yay...
Now I tried using gfil and nothing...it keeps failing.
Click to expand...
Click to collapse
Locked bootloader too?
dEFLASH said:
Locked bootloader too?
Click to expand...
Click to collapse
Yes
The easier Way for me was
Download Chinese ROM from link above
Open Lenovo Smart and Rescue assistant and let it download Lenovo L70081 ROM
Open folder with downloaded ROM from Lenovo Smart and Rescue assistant - you should see bunch of extracted ROM files
Go directly into the ROM Folder what namend "L70081_ROW_SECURE_USER_......"
Delete all files (abl.elf, aop.mbn, and so on) from that ROM folder
Extract Chinese ROM folder and go into the extracted Folder named "L70081_CN_SECURE_USER_......"
Copy all the files from inside the folder "L70081_CN_SECURE_USER_......" to the Folder "L70081_ROW_SECURE_USER_......"
Run standard Rescue process in Lenovo Smart and Rescue assistant
After this, device will have Chinese ROM and will be booted in this ROM.
This worked for me two times
x.0ldB0y.x said:
The easier Way for me was
Download Chinese ROM from link above
Open Lenovo Smart and Rescue assistant and let it download Lenovo L70081 ROM
Open folder with downloaded ROM from Lenovo Smart and Rescue assistant - you should see bunch of extracted ROM files
Go directly into the ROM Folder what namend "L70081_ROW_SECURE_USER_......"
Delete all files (abl.elf, aop.mbn, and so on) from that ROM folder
Extract Chinese ROM folder and go into the extracted Folder named "L70081_CN_SECURE_USER_......"
Copy all the files from inside the folder "L70081_CN_SECURE_USER_......" to the Folder "L70081_ROW_SECURE_USER_......"
Run standard Rescue process in Lenovo Smart and Rescue assistant
After this, device will have Chinese ROM and will be booted in this ROM.
This worked for me two times
Click to expand...
Click to collapse
So the thread is cn to global, but your instructions are to get to cn rom. Confused.
bs3pro said:
So the thread is cn to global, but your instructions are to get to cn rom. Confused.
Click to expand...
Click to collapse
No this thread is for firmware issues. I got mine working using the method oldboy mentions.
I tried several times, but now my cell phone doesn't show anything on the screen. Could you give me a hand? in qfil several errors appear.
eduardosilvaedias said:
I tried several times, but now my cell phone doesn't show anything on the screen. Could you give me a hand? in qfil several errors appear.
Click to expand...
Click to collapse
need to search on google. there have a few thing tht lead to sahara fail. n let the phone in download mode for a long time also one of it. after u connet to pc u need to press download quick.
@x.0ldB0y.x
Only question others may wonder: did you unlock your bootloader before you performed the region switch?
i tried replacing global rom with china rom in rsa now my phone is brick and i tried flashing in qfil it keeps on failing my phone is locked bootloader. any fix?