Dell venue 8 won't boot after failed update - Dell Venue

I have this error when I update my tablet
I can not enter the nandroid
when I try to enter the nandroid
the battery icon appears with the question mark (?)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
when I connect the tablet to the PC appears this

Plug the tablet into an outlet let charge for 5 or 6 hours unplug and press power until dell icon appears release power and allow tablet to boot normally.

vampirefo said:
Plug the tablet into an outlet let charge for 5 or 6 hours unplug and press power until dell icon appears release power and allow tablet to boot normally.
Click to expand...
Click to collapse
when I try to connect the tablet appears this
https://www.youtube.com/watch?v=ziM_juuXh-s&feature=youtu.be

The video is showing wrong boot.img, you need to boot into fastboot and flash correct boot.img.
On my dell press and hold volume up and power, once you see dell icon release power and keep holding volume up til you get into fastboot mode, then flash correct boot.img.
Sent from my Venue 8 3830 using XDA Free mobile app
---------- Post added at 09:17 AM ---------- Previous post was at 09:02 AM ----------
Your first picture simply means tablet can't charge via computer, so charge via wall outlet, the reason you can't charge via computer is your boot.img is wrong or corrupt.
Once your tablet has charged via wall outlet for a few hours you need to get the tablet into fastboot mode, and replace the boot.img, you may need to replace the entire system, recovery, boot.img depends on what is corrupt, for now just replace boot.img.
Sent from my Venue 8 3830 using Tapatalk

vampirefo said:
The video is showing wrong boot.img, you need to boot into fastboot and flash correct boot.img.
On my dell press and hold volume up and power, once you see dell icon release power and keep holding volume up til you get into fastboot mode, then flash correct boot.img.
Sent from my Venue 8 3830 using XDA Free mobile app
---------- Post added at 09:17 AM ---------- Previous post was at 09:02 AM ----------
Your first picture simply means tablet can't charge via computer, so charge via wall outlet, the reason you can't charge via computer is your boot.img is wrong or corrupt.
Once your tablet has charged via wall outlet for a few hours you need to get the tablet into fastboot mode, and replace the boot.img, you may need to replace the entire system, recovery, boot.img depends on what is corrupt, for now just replace boot.img.
Sent from my Venue 8 3830 using Tapatalk
Click to expand...
Click to collapse
I will charge the tablet for a few hours
but when I try to enter the fastboot battery icon appears

gato06 said:
I will charge the tablet for a few hours
but when I try to enter the fastboot battery icon appears
Click to expand...
Click to collapse
It needs to charge first, the tablet should also charge while is recovery mode, provided recovery.img isn't corrupted as well.
Recovery mode on my tablet is hold volume down plus power, letting power go still holding volume down as soon as dell icon appears.
You can try on your tablet and see if you can get into recovery mode, if so you can charge via computer in recovery mode.
Sent from my Venue 8 3830 using Tapatalk

vampirefo said:
It needs to charge first, the tablet should also charge while is recovery mode, provided recovery.img isn't corrupted as well.
Recovery mode on my tablet is hold volume down plus power, letting power go still holding volume down as soon as dell icon appears.
You can try on your tablet and see if you can get into recovery mode, if so you can charge via computer in recovery mode.
Sent from my Venue 8 3830 using Tapatalk
Click to expand...
Click to collapse
When I press volume down + power I see the dell icon later I see the battery icon (?)

gato06 said:
When I press volume down + power I see the dell icon later I see the battery icon (?)
Click to expand...
Click to collapse
You are going to have to let tablet charge for a while, sounds like recovery is corrupt also, wont know for sure until tablet has charged, and you get into fastboot mode.
Sent from my Venue 8 3830 using Tapatalk

vampirefo said:
You are going to have to let tablet charge for a while, sounds like recovery is corrupt also, wont know for sure until tablet has charged, and you get into fastboot mode.
Sent from my Venue 8 3830 using Tapatalk
Click to expand...
Click to collapse
It's work man thanks the tablet start
you have the boot.img, recovery.img and the system
to venue 8 3830
o the link for that

gato06 said:
It's work man thanks the tablet start
you have the boot.img, recovery.img and the system
to venue 8 3830
o the link for that
Click to expand...
Click to collapse
They are in this thread.
http://forum.xda-developers.com/showthread.php?t=2681783
Sent from my Venue 8 3830 using Tapatalk

Related

can't turn off to install ROM , HELP :(

hello everybody
I've Flashed my Xperia P with kernel Nemesis_XP_v6.3[ENIGMA]
to recover a backup I've made before in this kernel
after flashing I can't recover CWM backup , it send me MD5 mismatch although I didn't do anything for CWM folder
then I tried to turned the phone off to flash the stock ROM again
but the phone can't turned off !!!
I tried to force shutdown with the power key and volume up for 10 sec then finally the phone turned off
I tried to flash the stock ROM but the phone can't boot to flashmode or fast boot or even boot when it's connected to PC
also I tried to turn it on but it can't with the power button only !!
the phone turn on with "power key + volume up"
please help me what should I do here ??
What happens when you connect in fastboot or flash mode. Any led displayed?
Sent from my Xperia P using XDA Premium 4 mobile app
Hamza Murad said:
What happens when you connect in fastboot or flash mode. Any led displayed?
Sent from my Xperia P using XDA Premium 4 mobile app
Click to expand...
Click to collapse
the phone when is turned off normally you can connect to PC with any mode.
but when I turned it off using Force method (power key + volume up) the phone doesn't respond to any connect to PC !
also it can't be turned on normally (by power key only) !
only when I pressed (power key + volume up) = (the same shutdown method) it turned on
and now I don't know how to let it shutdown normally to flash the ROM
Try the volume up + power while CWM is on and phone connected to the PC, this shult put in fastboot mode, then disconnect and try flash mode.
ChikeD said:
Try the volume up + power while CWM is on and phone connected to the PC, this shult put in fastboot mode, then disconnect and try flash mode.
Click to expand...
Click to collapse
I connected the the phone to PC and it's in CWM then press Power key + volume up until the phone vibrate 3 times but no connection to PC or the flashtool detect the phone !!!
I'm so confused
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
engnajjar said:
I connected the the phone to PC and it's in CWM then press Power key + volume up until the phone vibrate 3 times but no connection to PC or the flashtool detect the phone !!!
I'm so confused
Click to expand...
Click to collapse
Just the one vibration then leave the power, keep volume up
ChikeD said:
Just the one vibration then leave the power, keep volume up
Click to expand...
Click to collapse
the phone is turned off at all !!!!!!!!
maybe the battery is damaged or something like this ??
I try to turn it on by anyway but nothing happen
engnajjar said:
the phone is turned off at all !!!!!!!!
maybe the battery is damaged or something like this ??
I try to turn it on by anyway but nothing happen
Click to expand...
Click to collapse
All you did is flash the kernel and try to restore backup nothig else?
ChikeD said:
All you did is flash the kernel and try to restore backup nothig else?
Click to expand...
Click to collapse
yea , I think the main problem is the battery was drained because after I flash the kernel and can't restore the backup I turned it off from CWM well and plan to flash the ROM but in a moment I decide to turn it on to try to wipe data/Factory reset maybe I could restore the backup .
but the same I couldn't , so I decide to turn it off and flash the ROM , but I couldn't , the phone was not able to turn off from CWM as I did before .
at the end the phone was turned off due to the battery was drained
so I connect it to charger for about 3 hours but as the phone doesn't charge !
and now I'm so scare that maybe the battery or the phone is damaged ..... !
finally the problem is gone
my friend disassembled it and removed the battery cable then re-back
then the phone is able to be charged properly then flash the ROM

Droid razr xt912 no os installed soft bricked

Hi guys as the title says i have bricked the phone . i had a working liquid smooth rom v3.2 kitkat 4.4.4 installed using safe strap v3.73 but could not utilize the stock rom slot so i wiped it without backup intalled the custom rom it gave an error i didnt look at it and booted now i cant go back to safesttap
Only to boot menu selection which includes recovery ap fastboot bp tools etc . really need help guys and the battery's dead cant get it to charge
you will need to flash stock firmware with RSD Lite
to charge battery try
Booting from AP fastboot to charging mode
If the Device will only boot to AP Fastboot and it says Battery Low
Connect the phone/Device ato a Wall Charger (not PC)
-In AP Fastboot Mode hold Volume down& power buttons at the same time for +10 seconds
- When screen goes black...release power button
-Then IMMEDIATELY press and hold Vol - and Vol+ to boot to Boot Menu.
- In Boot Menu scroll down with volume down to BP Tools, press volume up to select
- Device should boot to Charging Mode with battery icon
- Once battery is charged, try flashing in AP Fastboot again
This will only work if battery charging Firmware is still preset and not corrupted
If Motorola Device will not boot to Charging Mode, a Fastboot cable will be needed.
http://goo.gl/QllP1j
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sent from my XT907 using Tapatalk
Thx for the reply
Get the fast boot cable! Best 16$ I ever spent lol. I've soft bricked my xt912 at least 3 times and thanks to that cable I'm back in the running in 15 minutes max!
Sent from my DROID SPYDER using XDA Premium 4 mobile app
Thats the prob can't find it anywhere
Amazon I got mine for 18$ shipped with 2 day shipping.
Sent from my DROID SPYDER using XDA Premium 4 mobile app
---------- Post added at 05:56 PM ---------- Previous post was at 05:54 PM ----------
I thought it was 16$ it was actually 18$ with the faster shipping. So worth it I freaking love the XT912 its my favorite phone now!
Sent from my DROID SPYDER using XDA Premium 4 mobile app
amkhan said:
Thats the prob can't find it anywhere
Click to expand...
Click to collapse
Motorola Fastboot/Factory Programming Cables Links
Sent from my XT907 using Tapatalk
Thanks guys
Dont worry i have given it to a harfware expert he will hardwire the battery for me than i can flash it with rsd lite

Xt912 ap fastboot after digitizer replacement

Oops sorry about the caps guys.
So i replaced the digitizer / lcd assembly on an xt912 and before screwing it all back together I wanted to test the lcd.
It's working fine, it's just stuck in M Motorola bootloop and it will go into ap fastboot mode stating PLEASE CONNECT USB etc. No other error...
I don't have the special cable,and keep in mind I don't have it fully assembled.
I do have another xt912 with the battery charged but has a bad lcd as well.
The phone In question - I have no idea if it booted before the lcd broke.
I can't get to recovery mode. Tried numerous times
wondering if I should just use the guts from the other xt912
Can i take out a charged battery from another razr to get this to boot?
Do you think I broke the motherboard?
Do you think this may be stuck in ap fastboot simply because the screws aren't back I yet?
I truly don't feel like downloading sdk kit all over again and flashing this etc etc.
dovedescent7 said:
Oops sorry about the caps guys.
So i replaced the digitizer / lcd assembly on an xt912 and before screwing it all back together I wanted to test the lcd.
It's working fine, it's just stuck in M Motorola bootloop and it will go into ap fastboot mode stating PLEASE CONNECT USB etc. No other error...
I don't have the special cable,and keep in mind I don't have it fully assembled.
I do have another xt912 with the battery charged but has a bad lcd as well.
The phone In question - I have no idea if it booted before the lcd broke.
I can't get to recovery mode. Tried numerous times
wondering if I should just use the guts from the other xt912
Can i take out a charged battery from another razr to get this to boot?
Do you think I broke the motherboard?
Do you think this may be stuck in ap fastboot simply because the screws aren't back I yet?
I truly don't feel like downloading sdk kit all over again and flashing this etc etc.
Click to expand...
Click to collapse
If AP fastboot doesn't say low battery, then it's not a battery issue, and a fastboot cable is not needed.
But it's not uncommon that firmware needs to be flashed after a hardware repair.
See Flashing with RSD Lite in the index
http://forum.xda-developers.com/showthread.php?t=3023837
[INDEX] Motorola Droid Razr Development (2015)
Sent from my XT907 using Tapatalk
Much appreciated . YeS it does say low battery sorry about that
dovedescent7 said:
Much appreciated . YeS it does say low battery sorry about that
Click to expand...
Click to collapse
Try Booting from AP fastboot to charging mode
If the Device will only boot to AP Fastboot and it says Battery Low
Connect the phone/Device ato a Wall Charger (not PC)
-In AP Fastboot Mode hold Volume down& power buttons at the same time for +10 seconds
- When screen goes black...release power button
-Then IMMEDIATELY press and hold Vol - and Vol+ to boot to Boot Menu.
- In Boot Menu scroll down with volume down to BP Tools, press volume up to select
- Device should boot to Charging Mode with battery icon
- Once battery is charged, try flashing in AP Fastboot again
This will only work if battery charging Firmware is still preset and not corrupted
If Motorola Device will not boot to Charging Mode, a Fastboot cable will be needed.
http://goo.gl/QllP1j
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sent from my XT907 using Tapatalk
this i all i can get to guys

Note 5 stock/adb access?

My phone is freezing/locking up a few seconds after loading the OS and I can't transfer any of my photos over since the phone jams and the connection stalls
I've tried a multiple solution regarding this problem but it won't go away.
Is there a way perhaps using adb I could retrieve my data without loading into the OS.
I cannot modify the phone in any way since it's under warranty and i will be getting it exchange soon.
Sent from my SM-N900W8 using Tapatalk
You should be able to activate USB Debugging in the Maintenance Boot Mode if you don't already have it. If you hold Volume Down and Power for like 10 seconds, you should boot into this and have that option. If the phone can still boot to the system, even if it freezes up when loaded, hopefully you can still adb pull the /sdcard/ with adb. Other than that, without loading a custom recovery, which will trip Knox, then there's not much to do.
I don't have the option for maintenance boot mode on the note 5.
Sent from my SM-N900W8 using Tapatalk
Can I access the phone with adb in download mode?
Sent from my SM-N900W8 using Tapatalk
Droidherder said:
I don't have the option for maintenance boot mode on the note 5.
Sent from my SM-N900W8 using Tapatalk
Click to expand...
Click to collapse
Droidherder said:
Can I access the phone with adb in download mode?
Sent from my SM-N900W8 using Tapatalk
Click to expand...
Click to collapse
It definitely should. https://www.youtube.com/watch?v=HVBresgUXEw - Skip to about 1:05 and watch the steps to get in to the mode.
adb does not work in Download Mode.
That just resets the phone for me. I press the volume down and power and let go right after it turns off and then the logo shows up and starts loading the OS
Sent from my SM-N900W8 using Tapatalk
Droidherder said:
That just resets the phone for me. I press the volume down and power and let go right after it turns off and then the logo shows up and starts loading the OS
Sent from my SM-N900W8 using Tapatalk
Click to expand...
Click to collapse
Try it from a powered off state.
es0tericcha0s said:
Try it from a powered off state.
Click to expand...
Click to collapse
That just boots the phone into safe mode
Sent from my SM-N900W8 using Tapatalk
Hmm. Safe mode is supposed to activate if you hold volume down after you let go of power but if you hold both together it should boot to the maintenance mode. Not sure why it's not working for you. I have booted into it with some S7s but have not tried with a Note 5, I don't think, but there's video proof it does have it. Unless your carrier had it disabled for some reason or you're not getting the timing right, not sure what to tell you.
es0tericcha0s said:
Hmm. Safe mode is supposed to activate if you hold volume down after you let go of power but if you hold both together it should boot to the maintenance mode. Not sure why it's not working for you. I have booted into it with some S7s but have not tried with a Note 5, I don't think, but there's video proof it does have it. Unless your carrier had it disabled for some reason or you're not getting the timing right, not sure what to tell you.
Click to expand...
Click to collapse
That keeps restarting the phone no matter how I do it
Sent from my SM-N900W8 using Tapatalk
So I did the volume down and power and now it's black screen but still powered on. I connected the cable to my PC and adb does detects an unauthorized device connected. Is it possible to still retrieve data?
Sent from my SM-N900W8 using Tapatalk
Edit
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Is this good, and can anyone guide me through in how to retrieve data if possible?
Sent from my SM-N900W8 using Tapatalk
You'll have to see if you get prompted to authorize on the phone when you reboot before it freezes... I hadn't tried this before without having the phone authorized as it's one of the first things I do with my phone because of stuff like this...
es0tericcha0s said:
You'll have to see if you get prompted to authorize on the phone when you reboot before it freezes... I hadn't tried this before without having the phone authorized as it's one of the first things I do with my phone because of stuff like this...
Click to expand...
Click to collapse
I've tried booting in the OS with the adb connection but no option shows up to authorize anything unless it's somewhere else?
Sent from my SM-N900W8 using Tapatalk
Leave phone plugged in and reboot and in command prompt type :
adb wait-for-device devices
When you reboot and PC recognizes it, this should bring up the prompt.
es0tericcha0s said:
Leave phone plugged in and reboot and in command prompt type :
adb wait-for-device devices
When you reboot and PC recognizes it, this should bring up the prompt.
Click to expand...
Click to collapse
Alright I was able to click the prompt and the check box to remember the device before it locked up. I then rebooted it into maintenance mode which only shows me a black screen btw and adb still notes unauthorized in the CMD window
Sent from my SM-N900W8 using Tapatalk
I swear I'm fed up with this **** and it's stupid lockup. I can't do **** before it freezes up on me. I'm so frustrated already.
Sent from my SM-N900W8 using Tapatalk
You should be able to pull the sdcard with adb while it's booted even though the OS is not responding.
es0tericcha0s said:
You should be able to pull the sdcard with adb while it's booted even though the OS is not responding.
Click to expand...
Click to collapse
The phone is currently frozen and adb is recognizing the device. Not sure if this works or not but what command do I type to get the dcim folder. It's where my photos are located?
Sent from my SM-N900W8 using Tapatalk
adb pull /sdcard/DCIM/
and
adb pull /sdcard/Pictures
Some other apps save pictures there too.

Phone not booting. It's turnning eRecovery

Hello. Today I have a problem with my mothers' Huawei P20 Lite.
So lets start from the begging. Phone was lying about 1.5 years.
Yestreday I decided to turn it on. The battery was totally dead so I took off backplate and disconected the battery.
Then I connected phone to power and tried to turn it on.
I saw only Huawei logo and then phone enter eRecovery mode.
Spoiler: Photo after try to turn on
I tried first eRecovery option "Download the latest version and recovery but it didn't work
Spoiler: Photo fail recovery
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
When i connect it to PC i can enter FASTBOOT&RESCUE MODE (volume down+power btn)
Spoiler: Photo FASTBOOT MODE
On PC it's shows
Spoiler: Photo PC
So here is my question. How can I unbrick it? Is there any option?
Majke123PL said:
Hello. Today I have a problem with my mothers' Huawei P20 Lite.
So lets start from the begging. Phone was lying about 1.5 years.
Yestreday I decided to turn it on. The battery was totally dead so I took off backplate and disconected the battery.
Then I connected phone to power and tried to turn it on.
I saw only Huawei logo and then phone enter eRecovery mode.
Spoiler: Photo after try to turn on
I tried first eRecovery option "Download the latest version and recovery but it didn't work
Spoiler: Photo fail recovery
When i connect it to PC i can enter FASTBOOT&RESCUE MODE (volume down+power btn)
Spoiler: Photo FASTBOOT MODE
On PC it's shows
Spoiler: Photo PC
View attachment 5504805
So here is my question. How can I unbrick it? Is there any option?
Click to expand...
Click to collapse
I've never tried it, but I don't think the phone will boot properly without a battery. Battery plays primary role in the mobile phone circuitry.
You do not have access to Recovery and eRecovery (see your photo No.1), that's why update via eRecovery doesn't work, imo.
So I need to buy new battery and then try again? Or maybe you have any idea to recover old one?
Majke123PL said:
So I need to buy new battery and then try again?
Click to expand...
Click to collapse
Exactly.
Majke123PL said:
to recover old one?
Click to expand...
Click to collapse
it is strongly not recommended
Okey so i changed the battery and phone still isn't working .
When I connected new battery and connected to charger phone blink red LED 3 times and then started blinking like it is charing but no image of charging. When i tried to turn it on it bilnked again 3 times red LED and nothing else. I let it charge for about 12 hours and nothing changed.
Tommorow i will send a video.
Majke123PL said:
Okey so i changed the battery and phone still isn't working .
When I connected new battery and connected to charger phone blink red LED 3 times and then started blinking like it is charing but no image of charging. When i tried to turn it on it bilnked again 3 times red LED and nothing else. I let it charge for about 12 hours and nothing changed.
Tommorow i will send a video.
Click to expand...
Click to collapse
No need to send the video.
It looks like a damaged motherboard or dead emmc memory (see screen No.1), hard to say. It may not have been a good idea to turn on your phone without a battery...
Plug it on a computer, if it only says USB SER, then you can probably only restore it using testpoint & board firmware (if it is a software problem).
-Alf- said:
No need to send the video.
It looks like a damaged motherboard or dead emmc memory (see screen No.1), hard to say. It may not have been a good idea to turn on your phone without a battery...
Plug it on a computer, if it only says USB SER, then you can probably only restore it using testpoint & board firmware (if it is a software problem).
Click to expand...
Click to collapse
Okey so when the battery is connected i can just turn phone by power + vol down. And then phone enter fastboot&rescue mode. PC detect it like others -> fastboot 2.0
Link to video
Few months ago I tried to turn phone on and it turned on correctly.
It may not have been a good idea to turn on your phone without a battery...
Click to expand...
Click to collapse
And then about week ago i decided to turn it again and it won't turn on. So i thought that the battery may be down and i tried to turn it on without battery.
Majke123PL said:
PC detect it like others -> fastboot 2.0
Click to expand...
Click to collapse
It should be "Android Sooner Single ADB Interface", if I'm not mistaken. "fastboot 2.0" = 'black fastboot' = hard bricked phone.
I saw the video, but I can't advise you anything new, sorry.
Uncle Google is your friend, or ask here
Okey
Thanks

Categories

Resources