Related
Hi everybody ////////-----------------
I'm no expert in this section........ but I want you all to understand clearly( I didn't mean that Willey1986's guide not clear)
But for some new members, hard to understand that
First download FTF bundle & Recovery image from below link
http://forum.xda-developers.com/showthread.php?t=1192152
download Xrecovery 0.3GBready.zip from following link
http://forum.xda-developers.com/showthread.php?t=859571
here step by step,
1/-Flash 2.1 update1 stock rom with the lastest flash tool.......
2/-After that root your x10 with super one click
3/-After that install busy box.... then install Xrecovery 0.3(not GBready)
4/-Backup your current rom using xrecovery ,,,,, reboot
5/-Extract prerooted zip to your pc desktop , you will see one folder
6/-Then connect your phone with pc and mount sd card
open your memory card/xrecovery/backup/your backup date(folder)
7/-You will need to delete your backup date(folder) and replace with prerooted
folder
8/-Copy and paste Xrecovery 0.3 GB ready.zip to your sd card
9/-Then disconnect with pc and your phone and switch off your phone
10/-Boot up your phone with xrecovery and restore your backup folder
11/-And flash Xrecovery 0.3 GB ready.zip
12/-If finished, don't reboot your phone
13/-Take out your battery and flash FTF bundle (Extracted ftf file) with flash
tool
14/-Now start your x10i and ENJOY
THIS IS NOT MY ROM ,,,,,, I JUST SHOW HOW I DID
THANK YOU ALL.............
For point 2 and
3 you can do it with flashtool
Sent from my X10i using XDA App
Yeap!!!!
As you say.... can finish that point 2 and 3 with flash tool....
But that is a little bit hard to understand for some peoples
http://forum.xda-developers.com/showthread.php?t=1193753
good try btw.appreciated
Cheers for the guide Just one thing i think im misssing some drivers or somthing.
When i connect my phone and then start up flashtools it says X10 connected ect ect. Then i click flash select my firmware then it says preparing files for flashing then after that asks me to power off my phone ect and then i go to hold the usb and connect phone but it won't connect i have tried a numerous amount of times and its not having it.
Anybody know what my problem is cheers.
Cheers Jacko_oafc ..... sorry for that
there is something missing
b4 you flash you need to switch off your phone take out battery
then open flashtool and press flash button
then connect your usb cable to your pc and press your phone back button (don't release you hand ) and put usb cable to your phone(still need to press back button) and put battery you can see green light on your phone now release your hand from back button ... that's all
Ewaret said:
Cheers Jacko_oafc ..... sorry for that
there is something missing
b4 you flash you need to switch off your phone take out battery
then open flashtool and press flash button
then connect your usb cable to your pc and press your phone back button (don't release you hand ) and put usb cable to your phone(still need to press back button) and put battery you can see green light on your phone now release your hand from back button ... that's all
Click to expand...
Click to collapse
Tried that but its still not having it works on the laptop but no on my desktop PC must be missing drivers or somthing.
jacko_oafc said:
Tried that but its still not having it works on the laptop but no on my desktop PC must be missing drivers or somthing.
Click to expand...
Click to collapse
Then send your computer to me....
I will format for you.......
I'm 8pert in that section
XperiaU have a modified kernel with android 2.3.7, want to know if I upgrade to ICS by Sony's PC Companion can cause a problem for the modified kernel. (root)
If you use a modified kernel, then you have an unlocked bootloader so you cant use Sony PC Companion! Get Flashtool and the FTF instead Its a lot faster and simpler in my opinion
If you have any doubts on howto proceed, reply here or message me
Cheers
Min3r said:
If you use a modified kernel, then you have an unlocked bootloader so you cant use Sony PC Companion! Get Flashtool and the FTF instead Its a lot faster and simpler in my opinion
If you have any doubts on howto proceed, reply here or message me
Cheers
Click to expand...
Click to collapse
already heard about using FlashTool if you know of any link that teaches this would be grateful if you showed. but if I tried using the PC companio what would happen?
Found this on AndroidSoul Blog and modified for relevance :
1) Now copy the “.ftf” firmware file that you downloaded for your phone, and paste it inside the “firmwares” folder.
2) Double click the “FlashTool.exe” file.
3) Once the program opens — click on the “Flash” button. Its the Lightning button on top left
4) You’ll see the firmware that you copied loaded on the screen — click “Ok”!
Now it should ask you to connect your phone to the PC. So first plug the USB cable to PC, then pick up your phone and hold the “Volume Down” key and then connect the USB cable to your phone. Remember you’ve to hold the “Volume Down” key while connecting the USB cable to phone.
Once the phone gets connected — Flashtool will automatically start the flashing process.
Keep an eye on the Flashtool’s screen.
And once the process gets finished, disconnect your phone from PC and switch it ON.
Don’t freak if it takes longer to boot (that’s normal) as the phone has to build the cache again after flashing.
That will get you started And Sony PC Companion will give an error saying modified software if you try to flash on device with unlocked bootloader
ps : Since you are flashing a rom, use Flashmode and not fastboot when asked
Min3r said:
Found this on AndroidSoul Blog and modified for relevance :
1) Now copy the “.ftf” firmware file that you downloaded for your phone, and paste it inside the “firmwares” folder.
2) Double click the “FlashTool.exe” file.
3) Once the program opens — click on the “Flash” button. Its the Lightning button on top left
4) You’ll see the firmware that you copied loaded on the screen — click “Ok”!
Now it should ask you to connect your phone to the PC. So first plug the USB cable to PC, then pick up your phone and hold the “Volume Down” key and then connect the USB cable to your phone. Remember you’ve to hold the “Volume Down” key while connecting the USB cable to phone.
Once the phone gets connected — Flashtool will automatically start the flashing process.
Keep an eye on the Flashtool’s screen.
And once the process gets finished, disconnect your phone from PC and switch it ON.
Don’t freak if it takes longer to boot (that’s normal) as the phone has to build the cache again after flashing.
That will get you started And Sony PC Companion will give an error saying modified software if you try to flash on device with unlocked bootloader
ps : Since you are flashing a rom, use Flashmode and not fastboot when asked
Click to expand...
Click to collapse
Thank you. I'll test
Hi all,
I can't flash the stock rom on my xperia p with flashtool. I followed all step of many guide of various web sites (much the same). I trying to flash LT22i_6.2.A.1.100_Generic World.ftf, but when i connected my device in flash mode, i waited a few second and flashtool output this:
26/059/2014 15:59:57 - INFO - (MainSWT.java:127) - Device disconnected
26/000/2014 16:00:08 - INFO - (MainSWT.java:139) - Device connected with USB debugging off
26/000/2014 16:00:08 - INFO - (MainSWT.java:140) - For 2011 devices line, be sure you are not in MTP mode
Why? My device was in debug on when i plugged it, and Flashtool recognized it!
What is MTP mode??
Some details:
- My device is Xperia P LT22i;
- I have installed xperia p drivers;
- It has custom rom and kernel of Kit Kat's android version;
- It has unlocked BL;
- I'm using windows 7.
Sorry for my english. I hope this post is clear.
Thank's in advance =D
Turn device off
To flash it you must turn off your device & connect in Flashmode
"Device connected with USB debugging off" YOUR DEVICE ON NOT OFF
ya he is right
yes to flash firmware u have to connect the Device in flashmode (connect the device while holding vol - button )
MTP mode is media transfer mode u can access internal and SD card section through it..
Yes, i got it
Yes, i have pressed volume down on device turned off and plugged it. It sparkle green led, as guide say. Flashtool indeed output this:
27/032/2014 13:32:22 - INFO - Device connected in flash mode
It was on debug on, going to settings - developer options and ticking USB Debugging (hoping i have it right!)
- Jun - said:
Yes, i have pressed volume down on device turned off and plugged it. It sparkle green led, as guide say. Flashtool indeed output this:
27/032/2014 13:32:22 - INFO - Device connected in flash mode
It was on debug on, going to settings - developer options and ticking USB Debugging (hoping i have it right!)
Click to expand...
Click to collapse
You waited until the firmware prepare for firmware, and after it notified hooked smartphone?
SonyFan23 said:
You waited until the firmware prepare for firmware, and after it notified hooked smartphone?
Click to expand...
Click to collapse
If you mean the window that figure how to turn off the phone and plug it in flash mode appeared after the flashtool's notice "Please connect your device into flashmode", yes, I did it.
- Jun - said:
If you mean the window that figure how to turn off the phone and plug it in flash mode appeared after the flashtool's notice "Please connect your device into flashmode", yes, I did it.
Click to expand...
Click to collapse
And then what is?
- Jun - said:
If you mean the window that figure how to turn off the phone and plug it in flash mode appeared after the flashtool's notice "Please connect your device into flashmode", yes, I did it.
Click to expand...
Click to collapse
Without performing flash, open flashtool and connect in flash mode, see that it stays in flash mode for about 45 seconds, if not it may be driver issue.
Which window version you are using and have you installed flash mode driver that come with flashtool?
SonyFan23 said:
And then what is?
Click to expand...
Click to collapse
I don't know. I wrote here because i need help about this strange situation.
ChikeD said:
Without performing flash, open flashtool and connect in flash mode, see that it stays in flash mode for about 45 seconds, if not it may be driver issue.
Click to expand...
Click to collapse
Sorry, but i don't understand what i do exactly: i have to click the black flash icon, choose flash mode and see what does it do flashtool?
ChikeD said:
Which window version you are using and have you installed flash mode driver that come with flashtool?
Click to expand...
Click to collapse
I'm using windows 7. I have installed xperia p drivers.
Talking of drivers, the first time i used drivers to unlock bootloader, i didn't use flashtool. Instead (following instructions in an android forum) i download a fastboot-driver folder containing Flashtool_drivers.exe and installed drivers from there and unlocked BL from command line (cmd). Later i download and installed flashtool (Version 0.9.10.2beta6). The procedure for installing drivers are the same. It might be this the problem?
I'm not very pratical with this element and terms. So be patient with me xD
- Jun - said:
I don't know. I wrote here because i need help about this strange situation.
Sorry, but i don't understand what i do exactly: i have to click the black flash icon, choose flash mode and see what does it do flashtool?
I'm using windows 7. I have installed xperia p drivers.
Talking of drivers, the first time i used drivers to unlock bootloader, i didn't use flashtool. Instead (following instructions in an android forum) i download a fastboot-driver folder containing Flashtool_drivers.exe and installed drivers from there and unlocked BL from command line (cmd). Later i download and installed flashtool (Version 0.9.10.2beta6). The procedure for installing drivers are the same. It might be this the problem?
I'm not very pratical with this element and terms. So be patient with me xD
Click to expand...
Click to collapse
instruction
1 ) Run label - Flashtool.exe ( After installing the label should appear on your desktop , but if it does not, look for a shortcut to the root directory of the installed program " C :/ ... / Flashtool")
2 ) After starting the program you will see the Flashtool window inside which will block with the lightning bolt (click )
3 ) In the resulting window, select Flashmode
4) In the resulting window , in the left center of the screen you will see the firmware which was previously thrown in " C :/ ... / Flashtool / firmwares", click on the firmware
5) On the right will "tick" do not click if you do not know what you are doing . "Wipe Data" means erase all that was in the phone. Remove or leave - you decide for yourself. However, we strongly recommend that when a different version of firmware OS erase everything .
6) We click "OK "
7 ) You will see a graphical user guide your actions , namely : Turn off your phone , hold Volume Down + Connect the USB cable to the computer and then to your phone. You did everything right if you turned green diode . In no case " run " line of the firmware not vyderayte USB cable! Do not get scared if you see a mistake sometimes in red font !
9. ) Wait reported successful firmware "Flashing finished"
- Jun - said:
ISorry, but i don't understand what i do exactly: i have to click the black flash icon, choose flash mode and see what does it do flashtool?
Click to expand...
Click to collapse
Just open flashtool, do not click any icon, and connect in flash mode, see in the log if it get into flash mode and how long it says in flash mode untill it dissconnects.
- Jun - said:
I'm using windows 7. I have installed xperia p drivers.
Click to expand...
Click to collapse
You did not install flash and/or fastboot mode drivers too (though it seem you had if you unlocked bootloader)?
If you are on 64 bit windows you may try Flashtool.exe instead Flashtool64.exe.
Revealed(?)
@SonyFan23: Thanks for the guide. =)
I followed all steps carefully knowing terms and what it make me do. It's not the red font, but the red diode after the green one to worry me! -_-
@ChikeD: I try both Flashtool.exe and Flashtool64.exe. it seems they both work. In any case, i'm on 64 bit.
Yes, i unlock BL, so i had to install this drivers. But, after i connect my phone in flash mode as you told me, few seconds later flashtool show that the device is disconnected!
It seems that the problem is drivers.
What should i do? Unistall and install them again?
- Jun - said:
[MENTION=5735449]What should i do? Unistall and install them again?
Click to expand...
Click to collapse
Maybe, only I don't know how to uninstall them.
Hi All,
Need some help. My Samsung S3 mini i2800L was flashed with the wrong firmware in an attempt to upgrade to Jellybean 4.2.2 using odin and it failed . It remained in download mode and I did a battery pull ,now the phone is absolutely dead. Black Screen for all the following:Recovery Mode and Download Mode .The phone wont power on at all. The only sign of life , is when I plugged into my girl friend's Toshiba laptop via usb cable and it searched and installed the drivers.In addition Windows makes a sound when the device is plugged in and unplugged, but is not being recognized by Kies or Odin. I also tried a USB JIG with no success.
Is there any debrick file that I can use for to place on my SD card and attempt to boot from SD, or is JTAG the only option left?
yes!!! you can UNBrick it!!!
OK ... good news for you is it can still be read by the comp when connected (prompts by audio signal) ... it wont take more than 2 min to unbrick your phone... tell me have if you have a stock ROM available for your device?
unbrick Samsung galaxy s3 mini
omkarfrozen said:
OK ... good news for you is it can still be read by the comp when connected (prompts by audio signal) ... it wont take more than 2 min to unbrick your phone... tell me have if you have a stock ROM available for your device?
Click to expand...
Click to collapse
Yes I have downloaded a stock ROM from the internet that can be used. My phone is unlocked so I just downloaded a open firmware , please guide me on the steps required and thanks for responding BTW.
Leon bernard said:
Yes I have downloaded a stock ROM from the internet that can be used. My phone is unlocked so I just downloaded a open firmware , please guide me on the steps required and thanks for responding BTW.
Click to expand...
Click to collapse
have you downloaded SP flash tool along with it??? if not then search for that tool on needrom website... now turn off your phone by removing the battery... now open the SP flash tool and select the Scatter-Loading file present in your stock ROM folder... now click download button... then quickly connect your phone via USB... wait for 5 min ... you will get a message box with green circle and you are done!!! use your phone as you used to earlier...
will try it
omkarfrozen said:
have you downloaded SP flash tool along with it??? if not then search for that tool on needrom website... now turn off your phone by removing the battery... now open the SP flash tool and select the Scatter-Loading file present in your stock ROM folder... now click download button... then quickly connect your phone via USB... wait for 5 min ... you will get a message box with green circle and you are done!!! use your phone as you used to earlier...
Click to expand...
Click to collapse
Wow. Im going to try this when I reach home from work today, I will let you know if it works. Thanks a million
how to access scatter loading file
Leon bernard said:
Wow. Im going to try this when I reach home from work today, I will let you know if it works. Thanks a million
Click to expand...
Click to collapse
Hi ,
So I have the stock rom but its in md.5 format so I cant access the directories. Is their anyway I can convert it so I can access the scatter loading file ?
omkarfrozen said:
have you downloaded SP flash tool along with it??? if not then search for that tool on needrom website... now turn off your phone by removing the battery... now open the SP flash tool and select the Scatter-Loading file present in your stock ROM folder... now click download button... then quickly connect your phone via USB... wait for 5 min ... you will get a message box with green circle and you are done!!! use your phone as you used to earlier...
Click to expand...
Click to collapse
Hi ,
So I have the stock rom but its in md.5 format so I cant access the directories. Is their anyway I can convert it so I can access the scatter loading file ?
Leon bernard said:
Hi ,
So I have the stock rom but its in md.5 format so I cant access the directories. Is their anyway I can convert it so I can access the scatter loading file ?
Click to expand...
Click to collapse
OK if you have stock ROM in md5 then follow these steps
1) copy the md5 file on desktop
2. Download Odin 3.07
3. Switch off your phone and boot Galaxy S3 Mini I8200L into Download
Mode by pressing and holding the Volume Down+Home+Power buttons
(long press until the boot screen appear), now press Volume Up key to
proceed to Download Mode .IN CASE IT doesn't WORK TRY EVERY COMBINATION SO AS TO ACHIEVE 6TH STEP... IF NOTHING WORKS THEN JUST CONNECT THE PHONE WITHOUT PRESSING ANY COMBINATIONS...
4. Extract the downloaded Odin3.07 zip file and run the Odin3 v3.07.exe
file as an administrator (Right click on the .exe file and click on Run as
administrator)
5. Now connect your Galaxy S3 Mini I8200L to your computer via USB
cable
6. In Odin3 screen, you should see a COM Port number like “0:[COM7]” at
ID:COM section and “Added!” text at the message box. This means your
device has been detected by Odin3.
7. Make sure that, only the “Auto Reboot” and “F. Reset Time” options are
checked.
8. Now, extract the downloaded firmware .zip file, you’ll find a firmware file
with extension .tar.md5
9. In Odin screen, click on PDA button and select the firmware file with
.tar.md5 extension (The firmware file look something like:
I8200LXXDLJ5_I8200LODDDLI7_INU.tar.md5)
10. Now, click on the Start button to begin the installation process, wait few
moments.
11. Once completed, you would see “PASS!” message in ID:COM port having
green background
12. Your phone should automatically reboot after completion
13. You can now disconnect your phone from computer
14. Finish.
omkarfrozen said:
OK if you have stock ROM in md5 then follow these steps
1) copy the md5 file on desktop
2. Download Odin 3.07
3. Switch off your phone and boot Galaxy S3 Mini I8200L into Download
Mode by pressing and holding the Volume Down+Home+Power buttons
(long press until the boot screen appear), now press Volume Up key to
proceed to Download Mode .IN CASE IT doesn't WORK TRY EVERY COMBINATION SO AS TO ACHIEVE 6TH STEP... IF NOTHING WORKS THEN JUST CONNECT THE PHONE WITHOUT PRESSING ANY COMBINATIONS...
4. Extract the downloaded Odin3.07 zip file and run the Odin3 v3.07.exe
file as an administrator (Right click on the .exe file and click on Run as
administrator)
5. Now connect your Galaxy S3 Mini I8200L to your computer via USB
cable
6. In Odin3 screen, you should see a COM Port number like “0:[COM7]” at
ID:COM section and “Added!” text at the message box. This means your
device has been detected by Odin3.
7. Make sure that, only the “Auto Reboot” and “F. Reset Time” options are
checked.
8. Now, extract the downloaded firmware .zip file, you’ll find a firmware file
with extension .tar.md5
9. In Odin screen, click on PDA button and select the firmware file with
.tar.md5 extension (The firmware file look something like:
I8200LXXDLJ5_I8200LODDDLI7_INU.tar.md5)
10. Now, click on the Start button to begin the installation process, wait few
moments.
11. Once completed, you would see “PASS!” message in ID:COM port having
green background
12. Your phone should automatically reboot after completion
13. You can now disconnect your phone from computer
14. Finish.
Click to expand...
Click to collapse
Sigh , unfortunately odin is not detecting my phone at all. Remember that the phone is completely dead, which means it cant power on or go any mode . I think the SP Flash tool would work but I need the scatter file
Leon bernard said:
Sigh , unfortunately odin is not detecting my phone at all. Remember that the phone is completely dead, which means it cant power on or go any mode . I think the SP Flash tool would work but I need the scatter file
Click to expand...
Click to collapse
Download Samsung mobile drivers... Because you had said your friends laptopts prompts when you connect your mobile to his laptop. So remember 1thñg your phone is not completely dead yet. try if flash ROM from his laptop
omkarfrozen said:
Download Samsung mobile drivers... Because you had said your friends laptopts prompts when you connect your mobile to his laptop. So remember 1thñg your phone is not completely dead yet. try if flash ROM from his laptop
Click to expand...
Click to collapse
Ok so update: I downloaded Keis and installed all drivers. I recognized now that the phone is connecting as EMEI on PC. I clicked on it uninstall the drivers and re install it , but ODIN nor Keis still does not recognize phone , only computer recognizes phone as EMEI. Let me know your views.
Leon bernard said:
Ok so update: I downloaded Keis and installed all drivers. I recognized now that the phone is connecting as EMEI on PC. I clicked on it uninstall the drivers and re install it , but ODIN nor Keis still does not recognize phone , only computer recognizes phone as EMEI. Let me know your views.
Click to expand...
Click to collapse
get your Samsung usb drivers from here developer.samsung .com /board/download.do?bdId=0000000700&attachId=0000000001 (remove the spaces in between). give me some time so that I can find scatter file for your phone.
omkarfrozen said:
get your Samsung usb drivers from here developer.samsung .com /board/download.do?bdId=0000000700&attachId=0000000001 (remove the spaces in between). give me some time so that I can find scatter file for your phone.
Click to expand...
Click to collapse
drivers downloaded and installed. I await the scatter file. thanks for your efforts .
Leon bernard said:
Hi All,
Need some help. My Samsung S3 mini i2800L was flashed with the wrong firmware in an attempt to upgrade to Jellybean 4.2.2 using odin and it failed . It remained in download mode and I did a battery pull ,now the phone is absolutely dead. Black Screen for all the following:Recovery Mode and Download Mode .The phone wont power on at all. The only sign of life , is when I plugged into my girl friend's Toshiba laptop via usb cable and it searched and installed the drivers.In addition Windows makes a sound when the device is plugged in and unplugged, but is not being recognized by Kies or Odin. I also tried a USB JIG with no success.
Is there any debrick file that I can use for to place on my SD card and attempt to boot from SD, or is JTAG the only option left?
Click to expand...
Click to collapse
follow this brick
Help me too
Leon bernard said:
drivers downloaded and installed. I await the scatter file. thanks for your efforts .
Click to expand...
Click to collapse
I got the exact same issue.. my phone is samsung galaxy s3 mini. i will be very happy if you would also find the scatter file (although i still have no idea what is that) for my phone too, while i google it. i'm newbie, i'm not really sure what to find.. help me.. :crying:
tebegaya said:
I got the exact same issue.. my phone is samsung galaxy s3 mini. i will be very happy if you would also find the scatter file (although i still have no idea what is that) for my phone too, while i google it. i'm newbie, i'm not really sure what to find.. help me.. :crying:
Click to expand...
Click to collapse
Hey guys am using samsung s3 mini GT I8190, i recently flashed cyanogenmode 5.1.1 on my device, it was working fine but i decided to do a nandroid back up and in the process my phone died. it cannot power on or go to downloading mode. When i connect to my laptop there is a sound that its connected but then it disconnects help please..
omkarfrozen said:
OK if you have stock ROM in md5 then follow these steps
1) copy the md5 file on desktop
2. Download Odin 3.07
3. Switch off your phone and boot Galaxy S3 Mini I8200L into Download
Mode by pressing and holding the Volume Down+Home+Power buttons
(long press until the boot screen appear), now press Volume Up key to
proceed to Download Mode .IN CASE IT doesn't WORK TRY EVERY COMBINATION SO AS TO ACHIEVE 6TH STEP... IF NOTHING WORKS THEN JUST CONNECT THE PHONE WITHOUT PRESSING ANY COMBINATIONS...
4. Extract the downloaded Odin3.07 zip file and run the Odin3 v3.07.exe
file as an administrator (Right click on the .exe file and click on Run as
administrator)
5. Now connect your Galaxy S3 Mini I8200L to your computer via USB
cable
6. In Odin3 screen, you should see a COM Port number like “0:[COM7]” at
ID:COM section and “Added!” text at the message box. This means your
device has been detected by Odin3.
7. Make sure that, only the “Auto Reboot” and “F. Reset Time” options are
checked.
8. Now, extract the downloaded firmware .zip file, you’ll find a firmware file
with extension .tar.md5
9. In Odin screen, click on PDA button and select the firmware file with
.tar.md5 extension (The firmware file look something like:
I8200LXXDLJ5_I8200LODDDLI7_INU.tar.md5)
10. Now, click on the Start button to begin the installation process, wait few
moments.
11. Once completed, you would see “PASS!” message in ID:COM port having
green background
12. Your phone should automatically reboot after completion
13. You can now disconnect your phone from computer
14. Finish.
Click to expand...
Click to collapse
Hello, i need some help. I have tried all but always shows faild...i even use a recovery.tar and the bar goes all the way to the end but when the procces its almost finish it shows FAIL.
What can i do?
I do have the firmwarew file and it does not work, thx
Hello!
I have problem when try to get back to stock after installed GPe ROM...
Flashtool vagy Pc Companion doesnt work anybody could help me how to solve?
Have you tried rebooting your computer?
This usually fixes it for me when I have had that issue.
pTeronaut said:
Have you tried rebooting your computer?
This usually fixes it for me when I have had that issue.
Click to expand...
Click to collapse
Lot of time
yupiter00 said:
Hello!
I have problem when try to get back to stock after installed GPe ROM...
Flashtool vagy Pc Companion doesnt work anybody could help me how to solve?
Click to expand...
Click to collapse
First of all, this should be posted in the FAQ section, not here. To help you fix this can you please answer these questions?
1- What do you mean by Flashtool and PC companion "does not work"? What error messages do you get from each?
2- How do you use Flashtool? In Falsh mode or fastboot mode?
3- What is the version of your flashtool?
najoor said:
First of all, this should be posted in the FAQ section, not here. To help you fix this can you please answer these questions?
1- What do you mean by Flashtool and PC companion "does not work"? What error messages do you get from each?
2- How do you use Flashtool? In Falsh mode or fastboot mode?
3- What is the version of your flashtool?
Click to expand...
Click to collapse
Of course
1.Flashtool Said will be need usb debugging and uknown sources ,Sony Sompanion doesnt start repairing because modified ROM...
2.In Flashmode try in fastboot mode probadly doesnt answering...
3.0.9.18 the newest...
But the biggest problem when try the charge still rebooting because that bootlop
yupiter00 said:
Of course
1.Flashtool Said will be need usb debugging and uknown sources ,Sony Sompanion doesnt start repairing because modified ROM...
2.In Flashmode try in fastboot mode probadly doesnt answering...
3.0.9.18 the newest...
But the biggest problem when try the charge still rebooting because that bootlop
Click to expand...
Click to collapse
Please copy and paste your Flashtool log here, or attach it as a file.
OR:
Follow this instruction VERY CAREFULLY.
1- Disconnect your phone from the computer and turn it off completely.
2- Find and download an FTF that is specifically for your device. For example if your device is a C6833 find an FTF specifically for that model. You can find a ton of these FTFs in the general forum.
3- Make sure your Flashtool version is exactly 0.9.18.6. If not, uninstall it and install 0.9.18.6.
4- Run Flashtool and click on the icon that looks like a spark (flash device). Choose flash mode.
5- Navigate to the directory where the FTF is and select the directory.
6- You should see the contents of the FTF appear in the dialog window. Under "Wipe" select all of them (APPSLOG, DATA, and CACHE).
7- Click on flash and let the program do its work. Wait until it prompts you to connect the phone.
8- When prompted, hold the volume down key and then connect the phone to the USB port of the computer. Keep holding the key down until you see the flash starting. Wait until it completes.
If you get an error in any step, CLEARLY describe what fails AND include the error message by posting the log or a snapshot of your screen. If you just say "it didn't work" I won't be able to help.
Tried this very carefully but get this error!
najoor said:
Please copy and paste your Flashtool log here, or attach it as a file.
OR:
Follow this instruction VERY CAREFULLY.
1- Disconnect your phone from the computer and turn it off completely.
2- Find and download an FTF that is specifically for your device. For example if your device is a C6833 find an FTF specifically for that model. You can find a ton of these FTFs in the general forum.
3- Make sure your Flashtool version is exactly 0.9.18.6. If not, uninstall it and install 0.9.18.6.
4- Run Flashtool and click on the icon that looks like a spark (flash device). Choose flash mode.
5- Navigate to the directory where the FTF is and select the directory.
6- You should see the contents of the FTF appear in the dialog window. Under "Wipe" select all of them (APPSLOG, DATA, and CACHE).
7- Click on flash and let the program do its work. Wait until it prompts you to connect the phone.
8- When prompted, hold the volume down key and then connect the phone to the USB port of the computer. Keep holding the key down until you see the flash starting. Wait until it completes.
If you get an error in any step, CLEARLY describe what fails AND include the error message by posting the log or a snapshot of your screen. If you just say "it didn't work" I won't be able to help.
Click to expand...
Click to collapse
http://i62.tinypic.com/oqeu0m.png
Thanks for trying help
You are not using the version of flashtool that najoor told you to use.
DOWNLOAD VERSION 9.18.6, the latest version is causing that error.
pTeronaut said:
You are not using the version of flashtool that najoor told you to use.
DOWNLOAD VERSION 9.18.6, the latest version is causing that error.
Click to expand...
Click to collapse
That i use which version?
yupiter00 said:
That i use which version?
Click to expand...
Click to collapse
Ok:
1- Read post #6 carefully
2- Apply it.
3- If it doesn't work, read post #6 carefully again.
4- Repeat until it works.
najoor said:
Ok:
1- Read post #6 carefully
2- Apply it.
3- If it doesn't work, read post #6 carefully again.
4- Repeat until it works.
Click to expand...
Click to collapse
Ok and how fix always rebooting which kill the battery? I cant flash with this problem...Cannot charge
yupiter00 said:
Ok and how fix always rebooting which kill the battery? I cant flash with this problem...Cannot charge
Click to expand...
Click to collapse
And cannot get switch off with red button ad with vol + power off ...
When battery had enough power switch it immediatly and still rebooting that canoot charge....
najoor said:
Please copy and paste your Flashtool log here, or attach it as a file.
OR:
Follow this instruction VERY CAREFULLY.
1- Disconnect your phone from the computer and turn it off completely.
2- Find and download an FTF that is specifically for your device. For example if your device is a C6833 find an FTF specifically for that model. You can find a ton of these FTFs in the general forum.
3- Make sure your Flashtool version is exactly 0.9.18.6. If not, uninstall it and install 0.9.18.6.
4- Run Flashtool and click on the icon that looks like a spark (flash device). Choose flash mode.
5- Navigate to the directory where the FTF is and select the directory.
6- You should see the contents of the FTF appear in the dialog window. Under "Wipe" select all of them (APPSLOG, DATA, and CACHE).
7- Click on flash and let the program do its work. Wait until it prompts you to connect the phone.
8- When prompted, hold the volume down key and then connect the phone to the USB port of the computer. Keep holding the key down until you see the flash starting. Wait until it completes.
If you get an error in any step, CLEARLY describe what fails AND include the error message by posting the log or a snapshot of your screen. If you just say "it didn't work" I won't be able to help.
Click to expand...
Click to collapse
Hi again!
Problem now are in 7 step with flash because battery when enough power still get off ...That how to flash?
yupiter00 said:
Hi again!
Problem now are in 7 step with flash because battery when enough power still get off ...That how to flash?
Click to expand...
Click to collapse
If the phone not have enough battery do the following:
1- Makes sure it is turned off. To do so you can hold the power and volume up buttons simultaneously for a few seconds and then you will feel a vibration and then the phone will turn off.
2- leave the phone connected to a charger for about 10 hours.
If that doesn't charge the phone you will have to take it to a Sony repir center.
najoor said:
If the phone not have enough battery do the following:
1- Makes sure it is turned off. To do so you can hold the power and volume up buttons simultaneously for a few seconds and then you will feel a vibration and then the phone will turn off.
2- leave the phone connected to a charger for about 10 hours.
If that doesn't charge the phone you will have to take it to a Sony repir center.
Click to expand...
Click to collapse
04/027/2015 18:27:34 - INFO - Flashtool Version 0.9.18.6 built on 30-05-2015 22:30:00
04/027/2015 18:27:34 - INFO - Executing search strategies to find proxy selector
04/027/2015 18:27:34 - INFO - No proxy found for IE. Trying next one
04/027/2015 18:27:34 - INFO - No proxy found for firefox. Trying next one
04/027/2015 18:27:34 - INFO - No proxy found for java. Trying next one
04/027/2015 18:27:35 - INFO - Syncing devices from github
04/027/2015 18:27:39 - INFO - Scanning devices folder for changes.
04/027/2015 18:27:57 - INFO - Pulling changes from github.
04/027/2015 18:27:58 - INFO - Devices sync finished.
04/028/2015 18:28:02 - INFO - Selected Bundle for Sony Xperia Z Ultra (C6833). FW release : 14.5.A.0.270. Customization : Customized CE4
04/028/2015 18:28:02 - INFO - Preparing files for flashing
04/028/2015 18:28:03 - INFO - Device disconnected
04/030/2015 18:30:59 - INFO - Please connect your device into flashmode.
04/036/2015 18:36:35 - INFO - Device connected with USB debugging off
04/036/2015 18:36:35 - INFO - For 2011 devices line, be sure you are not in MTP mode
04/036/2015 18:36:39 - INFO - Device disconnected
04/041/2015 18:41:28 - INFO - Device connected with USB debugging off
04/041/2015 18:41:28 - INFO - For 2011 devices line, be sure you are not in MTP mode
04/041/2015 18:41:34 - INFO - Device disconnected
04/009/2015 19:09:27 - INFO - Device connected with USB debugging off
04/009/2015 19:09:27 - INFO - For 2011 devices line, be sure you are not in MTP mode
04/009/2015 19:09:54 - INFO - Device disconnected
04/010/2015 19:10:32 - INFO - Flash canceled
04/011/2015 19:11:00 - INFO - Selected Bundle for Sony Xperia Z Ultra (C6833). FW release : 14.4.A.0.108. Customization : 1275-9426
04/011/2015 19:11:00 - INFO - Preparing files for flashing
04/011/2015 19:11:56 - INFO - Please connect your device into flashmode.
04/018/2015 19:18:25 - INFO - Flash canceled
Flashtool logs...
najoor said:
If the phone not have enough battery do the following:
1- Makes sure it is turned off. To do so you can hold the power and volume up buttons simultaneously for a few seconds and then you will feel a vibration and then the phone will turn off.
2- leave the phone connected to a charger for about 10 hours.
If that doesn't charge the phone you will have to take it to a Sony repir center.
Click to expand...
Click to collapse
Thanks but little worrying about heating it will be doesn t porblem for 10 hours ?
najoor said:
If the phone not have enough battery do the following:
1- Makes sure it is turned off. To do so you can hold the power and volume up buttons simultaneously for a few seconds and then you will feel a vibration and then the phone will turn off.
2- leave the phone connected to a charger for about 10 hours.
If that doesn't charge the phone you will have to take it to a Sony repir center.
Click to expand...
Click to collapse
1 is working but only for few seconds after vibration will switch on
Probadly go to servis ,flashtool doesnt receiving flash mode only windows sound when touch it...
yupiter00 said:
Probadly go to servis ,flashtool doesnt receiving flash mode only windows sound when touch it...
Click to expand...
Click to collapse
I am sorry I'm trying to help you, but unfortunately I don't understand your sentence.
I looked at the log that you posted. it seems that when you connect your phone to the computer in step 8, the phone is not turned off.
Try turning the phone off again the way I told you. When you are turning it off if should not be connected to the computer or charger. Otherwise it turns right back on.
And don't worry about heating. After the phone is turned off you can connect it to the charger for many hours.
Don't try anything new. Just follow the instructions I gave you.
najoor said:
I am sorry I'm trying to help you, but unfortunately I don't understand your sentence.
I looked at the log that you posted. it seems that when you connect your phone to the computer in step 8, the phone is not turned off.
Try turning the phone off again the way I told you. When you are turning it off if should not be connected to the computer or charger. Otherwise it turns right back on.
And don't worry about heating. After the phone is turned off you can connect it to the charger for many hours.
Don't try anything new. Just follow the instructions I gave you.
Click to expand...
Click to collapse
Thanks man you are amazing It s done worked can i add to friend list?